Resources

An engineer tests a cylindrical aluminum alloy tie-rod of original length L0=2.40 mL_0 = 2.40\text{ m} subjected to an axial tensile force of F=3.60×104 NF = 3.60 \times 10^4\text{ N}. The alloy has a Young's modulus of E=7.00×1010 PaE = 7.00 \times 10^{10}\text{ Pa}. Under full design load, the operational safety specification mandates that the total axial elongation must not exceed ΔLmax⁡=1.80 mm\Delta L_{\max} = 1.80\text{ mm}. Calculate the minimum cross-sectional radius rmin⁡r_{\min} of the rod in millimeters required to satisfy this elongation limit within the elastic regime.

Answer and steps

Final answer

rmin⁡=14.8 mmr_{\min} = 14.8\text{ mm}

Steps

01

Relate Elastic Deformation to Rod Dimensions

According to Hooke's law in the elastic regime, the normal stress σ\sigma is directly proportional to the longitudinal strain ε\varepsilon, with the proportionality constant being Young's modulus EE:

σ=Eε\sigma = E \varepsilon

Expressing stress and strain in terms of the applied tensile force FF, original length L0L_0, cross-sectional area AA, and elongation ΔL\Delta L:

σ=FA,ε=ΔLL0\sigma = \frac{F}{A}, \quad \varepsilon = \frac{\Delta L}{L_0}

Substituting these definitions into Hooke's law yields:

FA=EΔLL0  ⟹  ΔL=FL0AE\frac{F}{A} = E \frac{\Delta L}{L_0} \implies \Delta L = \frac{F L_0}{A E}

02

Solve for the Minimum Cross-Sectional Area

To meet the safety specification, the elongation must satisfy ΔL≤ΔLmax⁡\Delta L \le \Delta L_{\max}. Since elongation is inversely proportional to area, the cross-sectional area must satisfy:

A≥FL0EΔLmax⁡A \ge \frac{F L_0}{E \Delta L_{\max}}

Convert all quantities to consistent SI units:

  • F=3.60×104 NF = 3.60 \times 10^4\text{ N}
  • L0=2.40 mL_0 = 2.40\text{ m}
  • E=7.00×1010 PaE = 7.00 \times 10^{10}\text{ Pa}
  • ΔLmax⁡=1.80 mm=1.80×10−3 m\Delta L_{\max} = 1.80\text{ mm} = 1.80 \times 10^{-3}\text{ m}

Calculate the minimum cross-sectional area Amin⁡A_{\min}:

Amin⁡=(3.60×104 N)(2.40 m)(7.00×1010 Pa)(1.80×10−3 m)=8.64×1041.26×108≈6.857×10−4 m2A_{\min} = \frac{(3.60 \times 10^4\text{ N})(2.40\text{ m})}{(7.00 \times 10^{10}\text{ Pa})(1.80 \times 10^{-3}\text{ m})} = \frac{8.64 \times 10^4}{1.26 \times 10^8} \approx 6.857 \times 10^{-4}\text{ m}^2

03

Determine the Minimum Radius

For a cylindrical rod with circular cross-section, A=πr2A = \pi r^2. Therefore, the required minimum radius rmin⁡r_{\min} is:

rmin⁡=Amin⁡π=FL0πEΔLmax⁡r_{\min} = \sqrt{\frac{A_{\min}}{\pi}} = \sqrt{\frac{F L_0}{\pi E \Delta L_{\max}}}

Substitute the values:

rmin⁡=6.857×10−4 m2π≈2.183×10−4 m2≈1.477×10−2 mr_{\min} = \sqrt{\frac{6.857 \times 10^{-4}\text{ m}^2}{\pi}} \approx \sqrt{2.183 \times 10^{-4}\text{ m}^2} \approx 1.477 \times 10^{-2}\text{ m}

Convert the radius to millimeters:

rmin⁡≈14.8 mmr_{\min} \approx 14.8\text{ mm}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert the maximum elongation from millimeters to meters when evaluating the cross-sectional area, resulting in a radius that is underestimated by a factor of √1000.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ΔL=F⋅L0A⋅E  ⟹  A=F⋅L0E⋅ΔL\Delta L = \frac{F \cdot L_0}{A \cdot E} \implies A = \frac{F \cdot L_0}{E \cdot \Delta L}

  2. Step 2

    A=3.60×104⋅2.407.00×1010⋅1.80  ⟹  A=8.64×1041.26×1011=6.857×10−7 m2A = \frac{3.60 \times 10^4 \cdot 2.40}{7.00 \times 10^{10} \cdot 1.80} \implies A = \frac{8.64 \times 10^4}{1.26 \times 10^{11}} = 6.857 \times 10^{-7}\text{ m}^2

    Correct

    A=(3.60×104 N)(2.40 m)(7.00×1010 Pa)(1.80×10−3 m)=6.857×10−4 m2A = \frac{(3.60 \times 10^4\text{ N})(2.40\text{ m})}{(7.00 \times 10^{10}\text{ Pa})(1.80 \times 10^{-3}\text{ m})} = 6.857 \times 10^{-4}\text{ m}^2

    You substituted the elongation value as 1.801.80 without converting it from millimeters to meters. Because 1.80 mm=1.80×10−3 m1.80\text{ mm} = 1.80 \times 10^{-3}\text{ m}, the denominator should be 1.26×108 N/m1.26 \times 10^8\text{ N/m}, giving an area of 6.857×10−4 m26.857 \times 10^{-4}\text{ m}^2.

  3. Step 3

    r=Aπ=6.857×10−7π=4.67×10−4 mr = \sqrt{\frac{A}{\pi}} = \sqrt{\frac{6.857 \times 10^{-7}}{\pi}} = 4.67 \times 10^{-4}\text{ m}

    Correct

    r=Aπ=6.857×10−4 m2π≈1.477×10−2 mr = \sqrt{\frac{A}{\pi}} = \sqrt{\frac{6.857 \times 10^{-4}\text{ m}^2}{\pi}} \approx 1.477 \times 10^{-2}\text{ m}

    You applied the correct formula relating area to radius for a circular cross-section, but the numerical result was affected by the incorrect area from the previous step.

  4. Step 4

    rmin⁡=0.467 mmr_{\min} = 0.467\text{ mm}

    Correct

    rmin⁡≈14.8 mmr_{\min} \approx 14.8\text{ mm}

    Your conversion from meters back to millimeters was executed correctly, but the final value reflects the propagated unit-conversion error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recalled and rearranged the axial deformation formula ΔL=FL0AE\Delta L = \frac{F L_0}{A E}.

You properly related the circular cross-sectional area to radius using A=πr2A = \pi r^2.

You carried out all subsequent algebraic and arithmetic steps accurately based on your substituted numbers.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing unit conversion

You wrote 1.801.80 instead of 1.80×10−3 m1.80 \times 10^{-3}\text{ m} when substituting the elongation ΔL\Delta L.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You overlooked checking that all length terms were converted to the base SI unit (meters) before computing with Young's modulus in pascals (N/m2\text{N/m}^2).

REASONING PATH
Your ACEpath teacher’s suggested approach
SI Unit Harmonization
  • Young's modulus is expressed in pascals (Pa=N/m2\text{Pa} = \text{N/m}^2), which requires all force terms to be in newtons (N\text{N}) and all length/elongation terms to be in meters (m\text{m}).

  • Before substituting into ΔL=FL0AE\Delta L = \frac{F L_0}{A E}, convert any values given in millimeters to meters by multiplying by 10−310^{-3}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert elongation to meters: ΔLmax⁡=1.80 mm=1.80×10−3 m\Delta L_{\max} = 1.80\text{ mm} = 1.80 \times 10^{-3}\text{ m}.

  2. Compute the minimum cross-sectional area: Amin⁡=(3.60×104 N)(2.40 m)(7.00×1010 Pa)(1.80×10−3 m)=8.64×1041.26×108≈6.857×10−4 m2A_{\min} = \frac{(3.60 \times 10^4\text{ N})(2.40\text{ m})}{(7.00 \times 10^{10}\text{ Pa})(1.80 \times 10^{-3}\text{ m})} = \frac{8.64 \times 10^4}{1.26 \times 10^8} \approx 6.857 \times 10^{-4}\text{ m}^2.

  3. Calculate the minimum radius: rmin⁡=6.857×10−4 m2π≈1.477×10−2 mr_{\min} = \sqrt{\frac{6.857 \times 10^{-4}\text{ m}^2}{\pi}} \approx 1.477 \times 10^{-2}\text{ m}.

  4. Convert the radius back to millimeters: rmin⁡=1.477×10−2 m×103 mm/m≈14.8 mmr_{\min} = 1.477 \times 10^{-2}\text{ m} \times 10^3\text{ mm/m} \approx 14.8\text{ mm}.

Final answer

rmin⁡≈14.8 mmr_{\min} \approx 14.8\text{ mm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always list your given quantities with explicit units and convert non-standard prefixes (like mm\text{mm} or cm\text{cm}) to meters before substituting.

  • Perform a sanity check on structural dimensions: a load of 36 kN36\text{ kN} on aluminum would rupture a wire of radius 0.47 mm0.47\text{ mm}, whereas 14.8 mm14.8\text{ mm} is a realistic rod size.

OverviewACEpath Teacher's Diagnosis

02 The student confuses the cross-sectional area formula for a circle by using the diameter formula A = π · d² instead of A = π · r², effectively omitting π · r² or taking r = √(A / (4π)) as if finding the radius from a diameter formula.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ΔL=F⋅L0A⋅E  ⟹  A=3.60×104⋅2.407.00×1010⋅1.80×10−3  ⟹  A=6.857×10−4 m2\Delta L = \frac{F \cdot L_0}{A \cdot E} \implies A = \frac{3.60 \times 10^4 \cdot 2.40}{7.00 \times 10^{10} \cdot 1.80 \times 10^{-3}} \implies A = 6.857 \times 10^{-4}\text{ m}^2

  2. Step 2

    A=4π⋅r2  ⟹  r=A4π=6.857×10−44πA = 4\pi \cdot r^2 \implies r = \sqrt{\frac{A}{4\pi}} = \sqrt{\frac{6.857 \times 10^{-4}}{4\pi}}

    Correct

    A=πr2  ⟹  r=Aπ=6.857×10−4 m2πA = \pi r^2 \implies r = \sqrt{\frac{A}{\pi}} = \sqrt{\frac{6.857 \times 10^{-4}\text{ m}^2}{\pi}}

    A cylindrical tie-rod has a flat circular cross-section with area A=πr2A = \pi r^2. The expression 4πr24\pi r^2 is the formula for the surface area of a sphere.

  3. Step 3

    r=7.39×10−3 m  ⟹  rmin⁡=7.39 mmr = 7.39 \times 10^{-3}\text{ m} \implies r_{\min} = 7.39\text{ mm}

    Correct

    rmin⁡=6.857×10−4 m2π≈1.48×10−2 m=14.8 mmr_{\min} = \sqrt{\frac{6.857 \times 10^{-4}\text{ m}^2}{\pi}} \approx 1.48 \times 10^{-2}\text{ m} = 14.8\text{ mm}

    Your arithmetic followed correctly from your formula, but the final numerical value was off by a factor of 4=2\sqrt{4} = 2 due to the incorrect geometric formula in the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied Hooke's law relating tensile force, initial length, Young's modulus, and elongation.

You correctly rearranged the equation to isolate the required cross-sectional area AA.

You converted the maximum elongation from millimeters to meters properly (1.80 mm=1.80×10−3 m1.80\text{ mm} = 1.80 \times 10^{-3}\text{ m}).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Geometric Formula Confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the two-dimensional cross-sectional area of a cylinder (A=πr2A = \pi r^2) with the three-dimensional surface area of a sphere (S=4πr2S = 4\pi r^2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Cross-Sectional Geometry
  • Tensile and compressive stress acts perpendicular to the transverse planar cross-section of a member; for a cylindrical rod, this face is a flat circle of area A=πr2=πd24A = \pi r^2 = \frac{\pi d^2}{4}.

  • Always sketch the cross-sectional slice of the member before writing down an area formula to ensure you are using a 2D planar area rather than a 3D surface area.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Relate the circular cross-sectional area to radius: A=πr2  ⟹  rmin⁡=AπA = \pi r^2 \implies r_{\min} = \sqrt{\frac{A}{\pi}}

  2. Substitute AA: rmin⁡=6.857×10−4 m2π≈2.183×10−4 m2≈1.477×10−2 mr_{\min} = \sqrt{\frac{6.857 \times 10^{-4}\text{ m}^2}{\pi}} \approx \sqrt{2.183 \times 10^{-4}\text{ m}^2} \approx 1.477 \times 10^{-2}\text{ m}

  3. Convert to millimeters: rmin⁡≈14.8 mmr_{\min} \approx 14.8\text{ mm}

Final answer

rmin⁡=14.8 mmr_{\min} = 14.8\text{ mm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review standard 2D plane area formulas (circle: πr2\pi r^2, rectangle: bhb h) versus 3D surface area formulas (sphere: 4πr24\pi r^2, cylinder lateral surface: 2πrh2\pi r h).

  • When solving mechanics of materials problems, clearly label cross-sectional area as Acircle=πr2A_{\text{circle}} = \pi r^2 before isolating rr.

OverviewACEpath Teacher's Diagnosis

03 The student confuses the radius with the cross-sectional area directly or forgets to take the square root when solving for the radius from A = π · r².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=F⋅L0E⋅ΔL  ⟹  A=3.60×104⋅2.407.00×1010⋅1.80×10−3=6.857×10−4 m2A = \frac{F \cdot L_0}{E \cdot \Delta L} \implies A = \frac{3.60 \times 10^4 \cdot 2.40}{7.00 \times 10^{10} \cdot 1.80 \times 10^{-3}} = 6.857 \times 10^{-4}\text{ m}^2

  2. Step 2

    A=π⋅r  ⟹  r=Aπ=6.857×10−4π=2.18×10−4 mA = \pi \cdot r \implies r = \frac{A}{\pi} = \frac{6.857 \times 10^{-4}}{\pi} = 2.18 \times 10^{-4}\text{ m}

    Correct

    A=πr2  ⟹  r=Aπ=6.857×10−4 m2π≈1.477×10−2 mA = \pi r^2 \implies r = \sqrt{\frac{A}{\pi}} = \sqrt{\frac{6.857 \times 10^{-4}\text{ m}^2}{\pi}} \approx 1.477 \times 10^{-2}\text{ m}

    The cross-sectional area of a cylinder is a circle, given by A=πr2A = \pi r^2. You wrote A=πrA = \pi r, which is dimensionally length rather than area, leading to an incorrect radius calculation.

  3. Step 3

    rmin⁡=0.218 mmr_{\min} = 0.218\text{ mm}

    Correct

    rmin⁡≈14.8 mmr_{\min} \approx 14.8\text{ mm}

    This value was obtained by converting your previous step's result to millimeters, inheriting the error from the incorrect area formula.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied Hooke's law to set up the axial elongation formula.

You accurately converted the maximum elongation from millimeters to meters.

You carried out the numerical calculation for the cross-sectional area without error.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect geometric area formula

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the formula for the area of a circle with a linear expression (A=πrA = \pi r), omitting the exponent on the radius and neglecting dimensional consistency ([Area]=length2[\text{Area}] = \text{length}^2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Area of a Circle
  • The cross-sectional area of a cylindrical rod with radius rr is A=πr2A = \pi r^2, so r=Aπr = \sqrt{\frac{A}{\pi}}.

  • Always verify that the geometric formula used matches the unit of area (meters squared) and includes taking the square root when solving for radius.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the correct geometric relation for the circular cross-section: A=πr2A = \pi r^2.

  2. Solve for the radius: r=Aπ=6.857×10−4 m2π≈1.477×10−2 mr = \sqrt{\frac{A}{\pi}} = \sqrt{\frac{6.857 \times 10^{-4}\text{ m}^2}{\pi}} \approx 1.477 \times 10^{-2}\text{ m}.

  3. Convert the radius from meters to millimeters: rmin⁡=1.477×10−2 m×103 mm/m≈14.8 mmr_{\min} = 1.477 \times 10^{-2}\text{ m} \times 10^3\text{ mm/m} \approx 14.8\text{ mm}.

Final answer

rmin⁡=14.8 mmr_{\min} = 14.8\text{ mm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review basic geometric formulas for circles, specifically distinguishing circumference (C=2πrC = 2\pi r) and area (A=πr2A = \pi r^2).

  • Perform dimensional analysis on intermediate formulas to ensure both sides have matching units before substituting numbers.

Lock it in

Similar question

01

A steel wire (E=2.00×1011 PaE = 2.00 \times 10^{11}\text{ Pa}) of initial length L0=1.50 mL_0 = 1.50\text{ m} has a circular cross-section of radius r=1.00 mmr = 1.00\text{ mm}. Calculate the elongation ΔL\Delta L in millimeters when subjected to a tensile force of F=500 NF = 500\text{ N}.

Answer

ΔL≈1.19 mm\Delta L \approx 1.19\text{ mm}. First convert radius: r=1.00×10−3 mr = 1.00 \times 10^{-3}\text{ m}, so A=πr2=π(1.00×10−3 m)2≈3.142×10−6 m2A = \pi r^2 = \pi (1.00 \times 10^{-3}\text{ m})^2 \approx 3.142 \times 10^{-6}\text{ m}^2. Then ΔL=FL0AE=(500 N)(1.50 m)(3.142×10−6 m2)(2.00×1011 Pa)≈1.193×10−3 m=1.19 mm\Delta L = \frac{F L_0}{A E} = \frac{(500\text{ N})(1.50\text{ m})}{(3.142 \times 10^{-6}\text{ m}^2)(2.00 \times 10^{11}\text{ Pa})} \approx 1.193 \times 10^{-3}\text{ m} = 1.19\text{ mm}.

02

A brass rod of original length L0=3.00 mL_0 = 3.00\text{ m} and Young's modulus E=1.05×1011 PaE = 1.05 \times 10^{11}\text{ Pa} must not stretch more than ΔLmax⁡=0.750 mm\Delta L_{\max} = 0.750\text{ mm} under a load of F=2.10×104 NF = 2.10 \times 10^4\text{ N}. Find the minimum required diameter dmin⁡d_{\min} in millimeters.

Answer

dmin⁡≈36.9 mmd_{\min} \approx 36.9\text{ mm}. Convert ΔLmax⁡=7.50×10−4 m\Delta L_{\max} = 7.50 \times 10^{-4}\text{ m}. Calculate required area: Amin⁡=FL0EΔLmax⁡=(2.10×104 N)(3.00 m)(1.05×1011 Pa)(7.50×10−4 m)=8.00×10−4 m2A_{\min} = \frac{F L_0}{E \Delta L_{\max}} = \frac{(2.10 \times 10^4\text{ N})(3.00\text{ m})}{(1.05 \times 10^{11}\text{ Pa})(7.50 \times 10^{-4}\text{ m})} = 8.00 \times 10^{-4}\text{ m}^2. Then dmin⁡=4Amin⁡π=4×8.00×10−4π≈3.192×10−2 m=31.9 mmd_{\min} = \sqrt{\frac{4 A_{\min}}{\pi}} = \sqrt{\frac{4 \times 8.00 \times 10^{-4}}{\pi}} \approx 3.192 \times 10^{-2}\text{ m} = 31.9\text{ mm} (or rmin⁡≈15.96 mm  ⟹  dmin⁡≈31.9 mmr_{\min} \approx 15.96\text{ mm} \implies d_{\min} \approx 31.9\text{ mm}).

03

Two solid cylindrical rods, one made of aluminum (EAl=7.00×1010 PaE_{\text{Al}} = 7.00 \times 10^{10}\text{ Pa}) and one of titanium (ETi=1.10×1011 PaE_{\text{Ti}} = 1.10 \times 10^{11}\text{ Pa}), have identical original lengths and are subjected to the same tensile force. If both rods experience the exact same axial elongation, determine the ratio of the radius of the aluminum rod to the radius of the titanium rod (rAl/rTir_{\text{Al}} / r_{\text{Ti}}).

Answer

rAl/rTi≈1.25r_{\text{Al}} / r_{\text{Ti}} \approx 1.25. Since ΔL=FL0πr2E\Delta L = \frac{F L_0}{\pi r^2 E} is identical for both rods with equal FF and L0L_0, the product r2Er^2 E must be equal: rAl2EAl=rTi2ETir_{\text{Al}}^2 E_{\text{Al}} = r_{\text{Ti}}^2 E_{\text{Ti}}. Therefore, rAlrTi=ETiEAl=1.10×10117.00×1010=117≈1.25\frac{r_{\text{Al}}}{r_{\text{Ti}}} = \sqrt{\frac{E_{\text{Ti}}}{E_{\text{Al}}}} = \sqrt{\frac{1.10 \times 10^{11}}{7.00 \times 10^{10}}} = \sqrt{\frac{11}{7}} \approx 1.25.

Loading workspace…