Resources
An insulated copper calorimeter cup of mass contains of liquid water in thermal equilibrium at an unknown initial temperature . When of dry ice at is added to the water, the ice melts completely, and the final equilibrium temperature of the entire apparatus is measured to be . Assuming no heat is lost to the surroundings, determine the initial temperature of the calorimeter and water. Use , , and .
Answer and steps
Final answer
Steps
Principle of Conservation of Energy
Because the calorimeter is thermally insulated and no heat is exchanged with the surroundings, the total heat absorbed by the cold substance must equal the total heat released by the warm substances:
Here:
- The ice absorbs heat to melt and then warms from to the final equilibrium temperature .
- The warm water and the copper calorimeter release heat as they cool from the unknown initial temperature to .
Calculate the Heat Absorbed by the Ice ()
The ice undergoes two distinct thermal processes:
- Phase change (melting): The ice at melts completely into liquid water at .
- Temperature increase of the melted water: The resulting water warms from to .
Total heat gained by the ice system:
Common Pitfall: A frequent error is accounting only for the latent heat of fusion () and forgetting that the melted ice water must also be warmed up to the final equilibrium temperature ().
Express the Heat Released by the Calorimeter and Water ()
Both the water initially present and the copper cup cool from to :
Calculate the combined heat capacity of the water and copper calorimeter:
- For water:
- For copper:
Total heat capacity:
Therefore:
Solve for
Equate to :
Divide both sides by the total heat capacity:
Typical errors
01 The student forgets to account for warming the melted ice water from 0°C to the final equilibrium temperature of 14.5°C.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You calculated the latent heat required to melt the ice, but the resulting liquid water at must also absorb heat to warm up to the final temperature .
- Step 2
- Step 3Correct
Your algebraic setup and division were executed correctly, but this step inherits the incomplete value for from Step 1.
- Step 4Correct
Your final temperature is slightly lower than expected due to the omitted warming term.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly applied the conservation of energy principle by equating heat gained to heat lost.
You accurately computed the total heat capacity of the water and copper calorimeter.
You correctly calculated the latent heat of fusion for melting the ice.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the phase change as the complete thermal process for the ice, overlooking that after melting at , the newly formed liquid water must also warm to the mixture's final equilibrium temperature .
REASONING PATH
Your ACEpath teacher’s suggested approach- Track the full thermal journey of added mass
When ice at melts in warmer water, .
Always list two stages for a phase-changing additive when : the latent heat of fusion plus the sensible heat to reach .
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the sensible heat absorbed by the melted ice water: .
Find the complete heat gained: .
Equate to heat lost: .
Solve for the temperature change: .
02 The student neglects the heat capacity of the copper calorimeter cup and only includes the water when setting up heat lost.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You forgot to include the copper calorimeter cup. Because the copper cup was in thermal equilibrium with the initial water, it also cools from to and releases heat.
- Step 3Correct
Your algebraic procedure for solving for the temperature difference was carried out correctly, but the equation lacked the heat capacity of the copper cup.
- Step 4Correct
Your final temperature is higher than the actual value because the omitted heat capacity of the calorimeter cup caused the temperature drop to be overestimated.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly accounted for both the phase change of melting and the warming of the melted ice water.
You applied the conservation of energy principle by equating heat gained to heat lost.
You performed the algebraic isolation of the unknown temperature accurately.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisWhen modeling calorimetry experiments, you only accounted for the liquid water releasing heat and neglected the calorimeter cup itself. Any container holding the contents is in thermal contact with the liquid and must undergo the exact same temperature change.
REASONING PATH
Your ACEpath teacher’s suggested approach- Inventory All Thermal Bodies
Every mass in thermal contact that experiences a temperature change must be included in either or .
Before writing down the energy balance, list each item: the ice, the water, and the copper calorimeter container.
- Combined Heat Capacity
For substances cooling together over the same temperature change , total heat lost is .
Add to the heat capacity of water.
CORRECTED PATH
ACEpath Teacher's DemonstrationInclude the copper cup in the heat-loss expression: .
Calculate the combined heat capacity: .
Equate to your correct : .
Solve for the temperature change: .
03 The student forgets the latent heat of fusion and assumes the ice only warms as liquid water from 0°C to 14.5°C.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You calculated the heat needed to warm liquid water from to , but you forgot to include the latent heat of fusion () required to melt the solid ice at into water.
- Step 2
- Step 3Correct
Your algebra and thermal equilibrium setup were correct, but substituting the incomplete value for led to an incorrect initial temperature.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly combined the heat capacities of the copper cup and the initial water.
You set up the conservation of energy equation accurately.
You carried out the algebraic steps and arithmetic cleanly.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the added ice as liquid water warming from rather than solid ice that must first undergo a phase change.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking the phase transition term () when a substance changes physical state at its melting temperature before its temperature changes.
REASONING PATH
Your ACEpath teacher’s suggested approach- Phase Change Check
Whenever a substance starts in one phase and ends in another, you must include the latent heat term .
Before setting up heat equations, sketch the process path (e.g., Ice at Water at Water at ).
- Energy Balance Verification
Every step in the thermal path absorbs or releases heat; .
Count the arrows in your path sketch to ensure each corresponds to a distinct term in your heat balance equation.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the latent heat required to melt the ice: .
Add the sensible heat needed to warm the melted ice to : .
Equate heat lost to heat gained: .
Solve for the initial temperature: .
Lock it in
When solid ice at melts in liquid water and reaches equilibrium at , what two heat terms make up ?
. Latent heat melts the solid; sensible heat warms the resulting liquid.
Similar question
A ice cube at is placed into of water at in an ideal insulated container of negligible heat capacity. What is the final equilibrium temperature ? Use and .
Answer
. Key steps: . . Equating gives .
An aluminum calorimeter of mass () contains of water at . An unknown mass of ice at is dropped into the cup. If the final equilibrium temperature is , find . Use and .
Answer
(). Key steps: Heat released by cup and warm water is . Heat absorbed per kg of ice is . Thus .
A ice cube initially at is added to an insulated flask containing of liquid water at an unknown initial temperature . The final equilibrium temperature of the mixture is . Neglecting the flask's heat capacity, determine . Use , , and .
Answer
. Key steps: Ice undergoes three stages: warm to (), melt (), and warm liquid to (). Total . Equating to yields .