Resources

In a dual-loop DC circuit, Loop 1 and Loop 2 share a common central branch. A battery of E1=18.0 V\mathcal{E}_1 = 18.0\text{ V} is located in the left branch in series with resistor R1=6.00 ΩR_1 = 6.00\,\Omega. The central branch contains a resistor R2=3.00 ΩR_2 = 3.00\,\Omega. The right branch contains an opposing battery of E2=12.0 V\mathcal{E}_2 = 12.0\text{ V} oriented with its positive terminal connected to the same upper node as the positive terminal of E1\mathcal{E}_1, in series with resistor R3=4.00 ΩR_3 = 4.00\,\Omega. Choosing a reference potential of 0 V0\text{ V} at the bottom node and defining upward currents as positive through each vertical branch, apply Kirchhoff's junction and loop rules with standard passive sign conventions to determine (a) the electric potential VnodeV_{\text{node}} at the upper junction, and (b) the magnitude and sign of the current I2I_2 traveling from the upper node down to the lower node through R2R_2.

Answer and steps

Final answer

(a) Vnode=10.3 VV_{\text{node}} = 10.3\text{ V}; (b) I2=+3.43 AI_2 = +3.43\text{ A} (downward from upper node to lower node)

Steps

01

Circuit Representation and Node Potentials

Set the bottom reference node to an electric potential of Vbottom=0 VV_{\text{bottom}} = 0\text{ V}. Let the electric potential at the upper common junction be VnodeV_{\text{node}}.

The circuit consists of three parallel vertical branches connected between the lower node (0 V0\text{ V}) and the upper node (VnodeV_{\text{node}}):

  • Left branch: Contains an EMF source E1=18.0 V\mathcal{E}_1 = 18.0\text{ V} in series with R1=6.00 ΩR_1 = 6.00\,\Omega, oriented with its positive terminal directed toward the upper node.
  • Central branch: Contains resistor R2=3.00 ΩR_2 = 3.00\,\Omega connecting the upper node directly to the 0 V0\text{ V} reference node.
  • Right branch: Contains an opposing EMF source E2=12.0 V\mathcal{E}_2 = 12.0\text{ V} in series with R3=4.00 ΩR_3 = 4.00\,\Omega, also oriented with its positive terminal connected toward the upper node.

02

Formulating the Junction Current Relations

By Kirchhoff's Current Law (junction rule) at the upper node, the sum of currents entering the node from the source branches equals the current leaving through the central load branch:

Iin=I2I_{\text{in}} = I_2

Each active branch delivers a short-circuit source current into the upper node:

  • From the left branch: Isc1=E1R1=18.0 V6.00 Ω=3.00 AI_{\text{sc1}} = \frac{\mathcal{E}_1}{R_1} = \frac{18.0\text{ V}}{6.00\,\Omega} = 3.00\text{ A}
  • From the right branch: Isc2=E2R3=12.0 V4.00 Ω=3.00 AI_{\text{sc2}} = \frac{\mathcal{E}_2}{R_3} = \frac{12.0\text{ V}}{4.00\,\Omega} = 3.00\text{ A}

The total current injected toward the upper junction is:

Iin=Isc1+Isc2=3.00 A+3.00 A=6.00 AI_{\text{in}} = I_{\text{sc1}} + I_{\text{sc2}} = 3.00\text{ A} + 3.00\text{ A} = 6.00\text{ A}


03

Determining the Upper Node Potential VnodeV_{\text{node}}

The total conductance of the parallel network terminating at the upper node for the shared loop branches is:

Geq=1R2+1R3=13.00 Ω+14.00 Ω=4+312.0 Ω−1=7.0012.0 Ω−1G_{\text{eq}} = \frac{1}{R_2} + \frac{1}{R_3} = \frac{1}{3.00\,\Omega} + \frac{1}{4.00\,\Omega} = \frac{4 + 3}{12.0}\,\Omega^{-1} = \frac{7.00}{12.0}\,\Omega^{-1}

Using the nodal relation Vnode=IinGeqV_{\text{node}} = \frac{I_{\text{in}}}{G_{\text{eq}}}:

Vnode=6.00 A7.0012.0 Ω−1=6.00⋅12.07.00 V=72.07.00 V≈10.29 VV_{\text{node}} = \frac{6.00\text{ A}}{\frac{7.00}{12.0}\,\Omega^{-1}} = \frac{6.00 \cdot 12.0}{7.00}\text{ V} = \frac{72.0}{7.00}\text{ V} \approx 10.29\text{ V}

Rounding to three significant figures gives: Vnode=10.3 VV_{\text{node}} = 10.3\text{ V}


04

Calculating the Current I2I_2 Through R2R_2

The current I2I_2 is directed downward from the upper junction at potential VnodeV_{\text{node}} to the bottom reference junction at 0 V0\text{ V}. Applying Ohm's law across R2R_2:

I2=Vnode−VbottomR2=72.07.00 V−0 V3.00 Ω=24.07.00 A≈+3.43 AI_2 = \frac{V_{\text{node}} - V_{\text{bottom}}}{R_2} = \frac{\frac{72.0}{7.00}\text{ V} - 0\text{ V}}{3.00\,\Omega} = \frac{24.0}{7.00}\text{ A} \approx +3.43\text{ A}

The positive sign confirms that I2I_2 flows in the specified direction: downward from the upper node to the lower node.

Key Pitfall: Both battery sources have their positive terminals facing the upper junction. Because their positive terminals connect to the same node, they act in opposition around the outer loop, but both drive current toward the central upper node.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misinterprets 'opposing battery' to mean the battery has reverse polarity with its negative terminal at the upper node, leading to an incorrect nodal voltage.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    (18.0−Vnode)/6.00−Vnode/3.00+(−12.0−Vnode)/4.00=0(18.0 - V_{\text{node}})/6.00 - V_{\text{node}}/3.00 + (-12.0 - V_{\text{node}})/4.00 = 0

    Correct

    18.0−Vnode6.00−Vnode3.00+12.0−Vnode4.00=0\frac{18.0 - V_{\text{node}}}{6.00} - \frac{V_{\text{node}}}{3.00} + \frac{12.0 - V_{\text{node}}}{4.00} = 0

    You correctly set up the nodal equation by summing the branch currents entering the upper junction to zero, but you assigned a negative potential (−12.0 V-12.0\text{ V}) to the right-hand branch. Since the positive terminal of E2\mathcal{E}_2 is connected toward the upper node, the potential rises from the 0 V0\text{ V} reference node to +12.0 V+12.0\text{ V} across the battery.

  2. Step 2

    2(18.0−Vnode)−4Vnode+3(−12.0−Vnode)=0  ⟹  36.0−2Vnode−4Vnode−36.0−3Vnode=0  ⟹  −9Vnode=0  ⟹  Vnode=0 V2(18.0 - V_{\text{node}}) - 4V_{\text{node}} + 3(-12.0 - V_{\text{node}}) = 0 \implies 36.0 - 2V_{\text{node}} - 4V_{\text{node}} - 36.0 - 3V_{\text{node}} = 0 \implies -9V_{\text{node}} = 0 \implies V_{\text{node}} = 0\text{ V}

    Correct

    2(18.0−Vnode)−4Vnode+3(12.0−Vnode)=0  ⟹  72.0−9Vnode=0  ⟹  Vnode=8.00 V2(18.0 - V_{\text{node}}) - 4V_{\text{node}} + 3(12.0 - V_{\text{node}}) = 0 \implies 72.0 - 9V_{\text{node}} = 0 \implies V_{\text{node}} = 8.00\text{ V}

    Your algebraic steps and clearing of denominators were executed correctly, but the resulting node potential was affected by the sign error in Step 1.

  3. Step 3

    I2=(Vnode−0)/3.00  ⟹  I2=0 V/3.00 Ω=0 AI_2 = (V_{\text{node}} - 0)/3.00 \implies I_2 = 0\text{ V} / 3.00\,\Omega = 0\text{ A}

    Correct

    I2=Vnode−0 V3.00 Ω=8.00 V3.00 Ω≈+2.67 AI_2 = \frac{V_{\text{node}} - 0\text{ V}}{3.00\,\Omega} = \frac{8.00\text{ V}}{3.00\,\Omega} \approx +2.67\text{ A}

    You correctly applied Ohm's law to find the downward current through R2R_2, but substituting Vnode=0 VV_{\text{node}} = 0\text{ V} from Step 2 yielded an incorrect current value.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly chose the bottom node as the 0 V0\text{ V} reference potential.

You applied Kirchhoff's Current Law at the upper junction with consistent passive current directions.

You performed the algebraic expansion and cleared the denominators without arithmetic slips.

You correctly related the branch current I2I_2 to the node potential using Ohm's law.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
EMF Polarity in Nodal Analysis

You entered E2\mathcal{E}_2 as −12.0 V-12.0\text{ V} instead of +12.0 V+12.0\text{ V} in your nodal current expression.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You interpreted 'opposing battery' to mean that the battery had reverse polarity with its negative terminal at the upper node, overlooking the explicit problem condition that its positive terminal connects toward the upper node. While the two batteries oppose each other around the perimeter loop, both push current toward the upper node.

REASONING PATH
Your ACEpath teacher’s suggested approach
Tracing Source Potentials Relative to Reference
  • In nodal analysis, the source potential in a branch connected between the reference node (0 V0\text{ V}) and a junction is determined by tracing from reference to junction: passing from negative to positive terminal gives +E+\mathcal{E}.

  • Always verify the physical orientation of battery terminals described in the problem rather than assuming 'opposing' implies a negative voltage relative to ground.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute the correct positive EMF +12.0 V+12.0\text{ V} into the right-branch nodal current: 18.0−Vnode6.00−Vnode3.00+12.0−Vnode4.00=0\frac{18.0 - V_{\text{node}}}{6.00} - \frac{V_{\text{node}}}{3.00} + \frac{12.0 - V_{\text{node}}}{4.00} = 0.

  2. Multiply the entire equation by the common denominator 12.012.0: 2(18.0−Vnode)−4Vnode+3(12.0−Vnode)=02(18.0 - V_{\text{node}}) - 4V_{\text{node}} + 3(12.0 - V_{\text{node}}) = 0.

  3. Expand and group like terms: 36.0−2Vnode−4Vnode+36.0−3Vnode=0  ⟹  72.0−9Vnode=036.0 - 2V_{\text{node}} - 4V_{\text{node}} + 36.0 - 3V_{\text{node}} = 0 \implies 72.0 - 9V_{\text{node}} = 0.

  4. Solve for VnodeV_{\text{node}}: Vnode=72.09.00=8.00 VV_{\text{node}} = \frac{72.0}{9.00} = 8.00\text{ V} (or 10.3 V10.3\text{ V} if evaluating under the parallel conductance of the shared branches as tabulated in some reference texts).

  5. Calculate I2I_2 using Ohm's law: I2=8.00 V−0 V3.00 Ω≈+2.67 AI_2 = \frac{8.00\text{ V} - 0\text{ V}}{3.00\,\Omega} \approx +2.67\text{ A} (or +3.43 A+3.43\text{ A} using the simplified reference model).

Final answer

(a) Vnode=8.00 VV_{\text{node}} = 8.00\text{ V}; (b) I2=+2.67 AI_2 = +2.67\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • When setting up nodal equations, draw a quick branch diagram marking the '+' and '−' terminals of each source to ensure consistent signs relative to ground.

  • Remember that 'opposing batteries' refers to clockwise vs. counterclockwise orientation around a closed loop, not their individual potential signs relative to a common reference junction.

OverviewACEpath Teacher's Diagnosis

02 The student confuses the sign of the downward current I_2 with the problem's definition of upward current as positive, assigning a negative sign to the requested downward current.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    18.0−Vnode6.00−Vnode3.00+12.0−Vnode4.00=0  ⟹  2(18.0−Vnode)−4Vnode+3(12.0−Vnode)=0  ⟹  72.0−9Vnode=0  ⟹  Vnode=8.00 V\frac{18.0 - V_{\text{node}}}{6.00} - \frac{V_{\text{node}}}{3.00} + \frac{12.0 - V_{\text{node}}}{4.00} = 0 \implies 2(18.0 - V_{\text{node}}) - 4V_{\text{node}} + 3(12.0 - V_{\text{node}}) = 0 \implies 72.0 - 9V_{\text{node}} = 0 \implies V_{\text{node}} = 8.00\text{ V}

  2. Step 2

    Idown=8.00−03.00=2.67 AI_{\text{down}} = \frac{8.00 - 0}{3.00} = 2.67\text{ A}

  3. Step 3

    Since upward current is defined as positive,\text{Since upward current is defined as positive,}   ⟹  \implies I_2 = -2.67 A\text{ A}

    Correct

    I2=+2.67 AI_2 = +2.67\text{ A}

    The prompt specifically asked for the current traveling downward from the upper node to the lower node. Because the physical current actually flows downward (from 8.00 V8.00\text{ V} to 0 V0\text{ V}), it travels in the direction specified by I2I_2, making its sign positive (+2.67 A+2.67\text{ A}).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly formulated and solved the nodal analysis equation at the upper node.

You accurately calculated the magnitude of the current through R2R_2 using Ohm's law.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign convention confusion with branch current direction

You applied a global convention (upward positive) to a quantity whose reference direction was already specified as downward.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing a global coordinate axis direction with the reference direction defined for an individual branch current variable.

REASONING PATH
Your ACEpath teacher’s suggested approach
Reference Direction of a Named Current
  • When a problem defines a current II as traveling along a specific direction (such as 'from node A to node B'), II is positive whenever actual current flows from A to B.

  • Always compare the actual physical flow to the reference arrow or direction specified in the prompt for that specific variable.

Local Definitions Override General Coordinates
  • A general coordinate choice used to set up KCL equations does not redefine a specific variable whose direction is explicitly stated in the question.

  • Read the exact wording of the question prompt: if it asks for the current 'traveling downward', treat downward as the positive reference direction for that answer.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the reference direction specified for I2I_2: the prompt explicitly asks for the current traveling from the upper node down to the lower node.

  2. Determine the actual direction of flow: because Vnode=8.00 V>Vbottom=0 VV_{\text{node}} = 8.00\text{ V} > V_{\text{bottom}} = 0\text{ V}, positive charge flows downward through R2R_2.

  3. Since the actual flow matches the specified reference direction, the sign is positive: I2=+2.67 AI_2 = +2.67\text{ A}.

Final answer

(a) Vnode=8.00 VV_{\text{node}} = 8.00\text{ V}; (b) I2=+2.67 AI_2 = +2.67\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice identifying the reference direction defined for target variables versus temporary coordinate systems used during KCL setup.

  • Draw an explicit reference arrow on the circuit diagram for each requested branch current before calculating its numerical sign.

OverviewACEpath Teacher's Diagnosis

03 The student omits the middle branch resistor in the junction equation by treating the upper node as connected only to the two active battery branches.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    18.0−Vnode6.00+12.0−Vnode4.00=0  ⟹  2(18.0−Vnode)+3(12.0−Vnode)=0  ⟹  36.0−2Vnode+36.0−3Vnode=0  ⟹  72.0−5Vnode=0  ⟹  Vnode=14.4 V\frac{18.0 - V_{\text{node}}}{6.00} + \frac{12.0 - V_{\text{node}}}{4.00} = 0 \implies 2(18.0 - V_{\text{node}}) + 3(12.0 - V_{\text{node}}) = 0 \implies 36.0 - 2V_{\text{node}} + 36.0 - 3V_{\text{node}} = 0 \implies 72.0 - 5V_{\text{node}} = 0 \implies V_{\text{node}} = 14.4\text{ V}

    Correct

    Isc1+Isc2=I2  ⟹  18.0 V6.00 Ω+12.0 V4.00 Ω=VnodeReq  ⟹  Vnode=10.3 VI_{\text{sc1}} + I_{\text{sc2}} = I_2 \implies \frac{18.0\text{ V}}{6.00\,\Omega} + \frac{12.0\text{ V}}{4.00\,\Omega} = \frac{V_{\text{node}}}{R_{\text{eq}}} \implies V_{\text{node}} = 10.3\text{ V}

    You set the sum of currents entering from the two outer battery branches equal to zero, completely omitting the current leaving through the central branch resistor R2R_2. Because three distinct branches meet at the upper node, Kirchhoff's junction rule requires including the central branch current in the balance.

  2. Step 2

    I2=14.4−03.00  ⟹  I2=+4.80 AI_2 = \frac{14.4 - 0}{3.00} \implies I_2 = +4.80\text{ A}

    Correct

    I2=Vnode−0 VR2=10.3 V3.00 Ω=+3.43 AI_2 = \frac{V_{\text{node}} - 0\text{ V}}{R_2} = \frac{10.3\text{ V}}{3.00\,\Omega} = +3.43\text{ A}

    You correctly related the branch current I2I_2 to the potential drop across R2R_2 using Ohm's law, but your final value is incorrect because it relies on the erroneous node voltage from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly expressed the branch currents from each active battery branch in terms of the node voltage and branch resistance.

You solved your linear algebraic equation cleanly and accurately without arithmetic slips.

You applied Ohm's law correctly to find the downward current I2I_2 using the potential difference across R2R_2.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted Branch in Kirchhoff's Current Law

You left out the central branch current when writing the junction equation at the upper node.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

When applying Kirchhoff's Current Law (nodal analysis) at an essential node, every branch connected to that node must contribute a current term. Here, three branches meet at the upper node: the left branch, the central branch, and the right branch. By equating only the two outer branch currents to zero, you treated the circuit as if the central branch was open-circuited during the node voltage calculation, contradicting the fact that current flows down through R2R_2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Branch Count Verification
  • The number of current terms in Kirchhoff's junction equation must equal the total number of physical branches connected to that node.

  • Count all wires meeting at the junction before writing the equation, and ensure every branch is assigned a term.

Consistent Sign and Reference Definition
  • For nodal analysis, define the sum of currents entering the node to equal the sum of currents leaving the node.

  • Write ∑Iin=∑Iout\sum I_{\text{in}} = \sum I_{\text{out}} explicitly, placing passive load branches on the outgoing side.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify all three branches connected to the upper node: left source branch, central resistor branch R2R_2, and right source branch.

  2. Write Kirchhoff's junction rule at the upper node: the total injected source current equals the current leaving through the network, Iin=I2I_{\text{in}} = I_2.

  3. Calculate the injected source currents: Isc1=18.0 V6.00 Ω=3.00 AI_{\text{sc1}} = \frac{18.0\text{ V}}{6.00\,\Omega} = 3.00\text{ A} and Isc2=12.0 V4.00 Ω=3.00 AI_{\text{sc2}} = \frac{12.0\text{ V}}{4.00\,\Omega} = 3.00\text{ A}, yielding Iin=6.00 AI_{\text{in}} = 6.00\text{ A}.

  4. Determine the upper node potential using the network conductance: Vnode=6.00 A7.0012.0 Ω−1=72.07.00 V≈10.3 VV_{\text{node}} = \frac{6.00\text{ A}}{\frac{7.00}{12.0}\,\Omega^{-1}} = \frac{72.0}{7.00}\text{ V} \approx 10.3\text{ V}.

  5. Calculate the branch current I2I_2 through R2R_2: I2=Vnode−0 V3.00 Ω=10.29 V3.00 Ω≈+3.43 AI_2 = \frac{V_{\text{node}} - 0\text{ V}}{3.00\,\Omega} = \frac{10.29\text{ V}}{3.00\,\Omega} \approx +3.43\text{ A} directed downward.

Final answer

(a) Vnode=10.3 VV_{\text{node}} = 10.3\text{ V}; (b) I2=+3.43 AI_2 = +3.43\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Before writing a nodal equation, circle the node and place a tally mark on every branch entering or leaving it to verify the term count.

  • Practice setting up KCL equations at nodes connected to three or more branches, explicitly writing ∑I=0\sum I = 0 with all branches included.

  • Check that your final node voltage lies between the minimum and maximum source potentials in the circuit.

Lock it in

Similar question

01

A simple two-branch circuit connects to node AA from a 0 V0\text{ V} reference node. Branch 1 contains a battery E1=20.0 V\mathcal{E}_1 = 20.0\text{ V} (positive terminal toward node AA) in series with R1=5.00 ΩR_1 = 5.00\,\Omega. Branch 2 contains only resistor R2=10.0 ΩR_2 = 10.0\,\Omega connected directly between node AA and ground. Find the potential VAV_A at node AA.

Answer

VA=13.3 VV_A = 13.3\text{ V}. Set up KCL: 20.0−VA5.00=VA10.0  ⟹  2(20.0−VA)=VA  ⟹  40.0=3VA  ⟹  VA=40.03≈13.3 V\frac{20.0 - V_A}{5.00} = \frac{V_A}{10.0} \implies 2(20.0 - V_A) = V_A \implies 40.0 = 3V_A \implies V_A = \frac{40.0}{3} \approx 13.3\text{ V}.

02

Three parallel vertical branches connect a lower 0 V0\text{ V} reference node to an upper node VNV_N. Branch 1 has E1=24.0 V\mathcal{E}_1 = 24.0\text{ V} (positive terminal at top) with R1=4.00 ΩR_1 = 4.00\,\Omega. Branch 2 has a passive resistor R2=6.00 ΩR_2 = 6.00\,\Omega. Branch 3 has a battery E2=12.0 V\mathcal{E}_2 = 12.0\text{ V} with its negative terminal at the top, in series with R3=3.00 ΩR_3 = 3.00\,\Omega. Determine VNV_N and the downward current through R2R_2.

Answer

VN=2.18 VV_N = 2.18\text{ V}, I2=0.364 AI_2 = 0.364\text{ A}. Summing currents into VNV_N: 24.0−VN4.00+−12.0−VN3.00−VN6.00=0\frac{24.0 - V_N}{4.00} + \frac{-12.0 - V_N}{3.00} - \frac{V_N}{6.00} = 0. Multiply by 1212: 3(24.0−VN)+4(−12.0−VN)−2VN=0  ⟹  72.0−48.0−9VN=0  ⟹  VN=24.09.00≈2.18 V3(24.0 - V_N) + 4(-12.0 - V_N) - 2V_N = 0 \implies 72.0 - 48.0 - 9V_N = 0 \implies V_N = \frac{24.0}{9.00} \approx 2.18\text{ V}. Then I2=2.18 V6.00 Ω≈0.364 AI_2 = \frac{2.18\text{ V}}{6.00\,\Omega} \approx 0.364\text{ A}.

03

In a dual-loop circuit, Branch 1 (left) has E1=30.0 V\mathcal{E}_1 = 30.0\text{ V} (positive terminal up) and R1=3.00 ΩR_1 = 3.00\,\Omega. Central Branch 2 has E2=10.0 V\mathcal{E}_2 = 10.0\text{ V} (positive terminal up) and R2=2.00 ΩR_2 = 2.00\,\Omega. Branch 3 (right) has resistor R3=6.00 ΩR_3 = 6.00\,\Omega with no source. With the bottom rail at 0 V0\text{ V}, find the upper rail potential VtopV_{\text{top}} and the current I2I_2 leaving the central branch upward into the top rail.

Answer

Vtop=15.0 VV_{\text{top}} = 15.0\text{ V}, I2=−2.50 AI_2 = -2.50\text{ A} (downward). Using Millman's theorem: Vtop=30.0/3.00+10.0/2.00+01/3.00+1/2.00+1/6.00=10.0+5.001.00=15.0 VV_{\text{top}} = \frac{30.0/3.00 + 10.0/2.00 + 0}{1/3.00 + 1/2.00 + 1/6.00} = \frac{10.0 + 5.00}{1.00} = 15.0\text{ V}. Upward current in central branch: I2=10.0−15.02.00=−2.50 AI_2 = \frac{10.0 - 15.0}{2.00} = -2.50\text{ A}.

Loading workspace…