Resources
A small block of mass is projected up a rough ramp inclined at an angle of above the horizontal with an initial speed of . The coefficient of kinetic friction between the block and the ramp surface is . The block travels up the incline until it momentarily comes to rest at its highest point before impending back-slip. Taking , compute: (a) the total displacement traveled up the ramp, and (b) the work done by the friction force during this ascent.
Answer and steps
Final answer
(a) ; (b) .
Steps
Analyze the forces acting on the block
Choose a coordinate system aligned with the incline, where the positive -axis points up the incline and the positive -axis is perpendicular to the incline pointing outward.
The forces acting on the block as it slides up the incline are:
- Gravity (), acting straight downward:
- Component perpendicular to the surface:
- Component parallel to the surface: (directed down the ramp)
- Normal force (), acting perpendicular to the surface:
- Since there is no acceleration in the -direction, :
- Kinetic friction (), opposing the upward motion (directed down the ramp):
Substituting the given values:
Determine the displacement up the ramp ()
Apply the work-energy theorem, which states that the net work done on the block equals its change in kinetic energy:
At the highest point, the block momentarily comes to rest, so and :
Both gravity along the incline and kinetic friction oppose the upward displacement :
- Work done by gravity:
- Work done by friction:
- Normal force is perpendicular to the displacement, so .
Equating the total work to :
Cancel the mass and solve for :
Substitute the numerical values:
Compute the work done by friction ()
The kinetic friction force acts antiparallel to the displacement vector along the ramp ( between and ):
Using the unrounded values to avoid intermediate rounding errors:
Common Pitfall: Work done by kinetic friction is negative because the friction force acts in the direction opposite to the displacement. Be careful not to omit the negative sign.
Typical errors
01 The student uses sin(θ) instead of cos(θ) when determining the normal force on an inclined plane.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The normal force balances the perpendicular component of gravity, which is adjacent to the incline angle and given by , not .
- Step 2Correct
You correctly used the definition of kinetic friction , but your result was affected by the incorrect normal force from Step 1.
- Step 3Correct
You correctly summed the two forces opposing upward motion to find the deceleration, but the value carried forward the error in friction.
- Step 4Correct
Your kinematic relation for the stopping distance is completely correct, but the numerical answer is larger than expected due to the underestimated deceleration.
- Step 5Correct
You correctly recognized that kinetic friction does negative work opposite to the displacement, but the value was affected by your earlier intermediate numbers.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the two forces acting down the ramp during ascent as the parallel gravity component and kinetic friction.
You applied Newton's second law and constant-acceleration kinematics correctly to find the displacement.
You correctly recognized that work done by kinetic friction is negative.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou swapped sine and cosine when decomposing the gravitational force vector relative to the incline surface.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the parallel and perpendicular components of gravity on an incline. When the ramp angle is measured from the horizontal, the component of gravity perpendicular to the surface is , while the component parallel to the surface is .
REASONING PATH
Your ACEpath teacher’s suggested approach- Perpendicular vs. Parallel Gravity Components
For an incline at angle with the horizontal, and .
Always test the boundary case: as the ramp flattens (), the normal force must approach full weight , which requires .
CORRECTED PATH
ACEpath Teacher's DemonstrationRecalculate the normal force: .
Find kinetic friction: .
Find deceleration: .
Compute stopping displacement: .
Compute work done by friction: .
(a) ; (b)
02 The student subtracts the force of kinetic friction from the component of gravity instead of adding them when the block travels upward.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
(directed down the ramp)
Because the block is sliding up the ramp, kinetic friction acts down the ramp to oppose the motion. The parallel component of gravity also pulls down the ramp, so both forces point in the same direction and must be added together.
- Step 3Correct
You correctly applied Newton's second law, but the numerical acceleration is affected by the incorrect net force from the previous step.
- Step 4Correct
Your kinematic formula is correct, but using the underestimated deceleration resulted in an overly large displacement.
- Step 5Correct
You correctly identified that friction does negative work during the ascent, but the value is affected by the incorrect displacement.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly resolved the normal force perpendicular to the inclined plane.
You computed the magnitude of the kinetic friction force accurately using .
You correctly recognized that kinetic friction performs negative work on the ascending block.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou subtracted kinetic friction from the downhill gravitational force instead of adding them, assuming friction and gravity oppose each other rather than recognizing that both act down the incline when an object travels upward.
REASONING PATH
Your ACEpath teacher’s suggested approach- Determine the direction of kinetic friction
Kinetic friction always opposes relative velocity along the contact surface.
Draw the velocity vector first; if points up the incline, must point down the incline.
- Sum forces along the incline
Forces pointing in the same direction add together algebraically.
When a block slides upward, both and act down the incline, so the magnitude of the retarding force is .
CORRECTED PATH
ACEpath Teacher's DemonstrationFind the correct net retarding force down the ramp: .
Compute the deceleration: .
Calculate the stopping displacement: .
Calculate the work done by friction: .
(a) ; (b)
03 The student omits the negative sign in the calculation of work done by friction because friction opposes the displacement.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You calculated the magnitude accurately, but kinetic friction acts down the ramp while the displacement is up the ramp (an angle of ). Therefore, the work done by friction must be negative.
WHAT YOU DID WELL
Compliments from Your TeacherYou resolved the gravitational force components correctly along and perpendicular to the incline.
You calculated the normal force and kinetic friction force accurately.
You used Newton's second law and kinematics to find the correct displacement for part (a).
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the work done by friction as a simple product of magnitudes () rather than using the dot product .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking the directional relationship between force and displacement in the definition of work, specifically that dissipative forces such as kinetic friction oppose motion and do negative work.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check the angle between force and displacement
Always identify the angle between the force vector and the displacement vector. If the force opposes the motion (), the work done is negative.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the angle between the friction force (down the ramp) and displacement (up the ramp): .
Apply the definition of work: .
Substitute the numerical values: .
(a) ; (b)
Lock it in
For an incline tilted at angle above the horizontal, which trigonometric component of gravity acts perpendicular to the surface?
. Memory cue: as (flat ground), the perpendicular force must equal full weight , and .
Similar question
A box slides down a rough incline of with coefficient of kinetic friction . Taking , find the magnitude of the normal force and the kinetic friction force .
Answer
. Then .
A block of mass is projected up a ramp inclined at with initial speed . If and , calculate the stopping distance along the ramp.
Answer
. Deceleration is . Then .
A crate is pushed up a incline by a constant horizontal pushing force . If , determine the normal force exerted by the ramp on the crate.
Answer
. Set perpendicular forces to zero: . Thus .