Resources

A student expects that narrowing a single slit will make the central illuminated band on a distant screen narrower. In an experiment, red laser light (λ=650 nm\lambda = 650\text{ nm}) passes through a slit whose width is reduced from a1=0.200 mma_1 = 0.200\text{ mm} to a2=0.0500 mma_2 = 0.0500\text{ mm}. With the screen located at L=1.50 mL = 1.50\text{ m}, calculate the linear width ww of the central maximum on the screen for both slit widths to quantitatively demonstrate how slit narrowing affects beam spreading.

Answer and steps

Final answer

For a1=0.200 mma_1 = 0.200\text{ mm}, w1=9.75×10−3 mw_1 = 9.75\times 10^{-3}\text{ m} (9.75 mm9.75\text{ mm}); for a2=0.0500 mma_2 = 0.0500\text{ mm}, w2=3.90×10−2 mw_2 = 3.90\times 10^{-2}\text{ m} (39.0 mm39.0\text{ mm}); narrowing the slit by a factor of 44 broadens the central maximum by a factor of 44.

Steps

01

Condition for the Central Maximum in Single-Slit Diffraction

When monochromatic light of wavelength λ\lambda passes through a single slit of width aa, diffraction produces an alternating pattern of bright and dark fringes on a distant screen.

The dark fringes (diffraction minima) occur where destructive interference takes place across the slit aperture, governed by: asin⁡θ=mλ(m=±1,±2,… )a \sin\theta = m\lambda \quad (m = \pm 1, \pm 2, \dots)

The central bright maximum lies between the first minimum on one side (m=+1m = +1) and the first minimum on the other side (m=−1m = -1). Because the distance to the screen LL is much larger than the slit width aa, the diffraction angle θ\theta is small, permitting the small-angle approximation sin⁡θ≈tan⁡θ≈yL\sin\theta \approx \tan\theta \approx \frac{y}{L}, where yy is the linear distance from the center of the screen to the minimum: a(y1L)=λ  ⟹  y1=λLaa \left(\frac{y_1}{L}\right) = \lambda \implies y_1 = \frac{\lambda L}{a}

The full linear width ww of the central maximum spans from −y1-y_1 to +y1+y_1: w=2y1=2λLaw = 2y_1 = \frac{2\lambda L}{a}


02

Convert Given Values to SI Units

  • Wavelength of red light: λ=650 nm=6.50×10−7 m\lambda = 650\text{ nm} = 6.50 \times 10^{-7}\text{ m}
  • Distance to screen: L=1.50 mL = 1.50\text{ m}
  • Initial slit width: a1=0.200 mm=2.00×10−4 ma_1 = 0.200\text{ mm} = 2.00 \times 10^{-4}\text{ m}
  • Reduced slit width: a2=0.0500 mm=5.00×10−5 ma_2 = 0.0500\text{ mm} = 5.00 \times 10^{-5}\text{ m}

03

Calculate the Width for Both Slit Settings

For the wider slit (a1=0.200 mma_1 = 0.200\text{ mm}): w1=2λLa1=2(6.50×10−7 m)(1.50 m)2.00×10−4 m=9.75×10−3 m=9.75 mmw_1 = \frac{2\lambda L}{a_1} = \frac{2(6.50 \times 10^{-7}\text{ m})(1.50\text{ m})}{2.00 \times 10^{-4}\text{ m}} = 9.75 \times 10^{-3}\text{ m} = 9.75\text{ mm}

For the narrower slit (a2=0.0500 mma_2 = 0.0500\text{ mm}): w2=2λLa2=2(6.50×10−7 m)(1.50 m)5.00×10−5 m=3.90×10−2 m=39.0 mmw_2 = \frac{2\lambda L}{a_2} = \frac{2(6.50 \times 10^{-7}\text{ m})(1.50\text{ m})}{5.00 \times 10^{-5}\text{ m}} = 3.90 \times 10^{-2}\text{ m} = 39.0\text{ mm}


04

Interpretation and Physical Insight

Comparing the two results: w2w1=39.0 mm9.75 mm=4\frac{w_2}{w_1} = \frac{39.0\text{ mm}}{9.75\text{ mm}} = 4

While geometric optics intuition suggests that a narrower opening should produce a narrower beam of light, wave optics shows an inverse relationship: w∝1aw \propto \frac{1}{a}. When the slit width is reduced by a factor of 44 (from 0.200 mm0.200\text{ mm} to 0.0500 mm0.0500\text{ mm}), diffraction spreads the light more widely, causing the central maximum to broaden by a factor of 44.

Common Pitfall: Do not confuse the single-slit diffraction condition asin⁡θ=mλa \sin\theta = m\lambda (which identifies minima) with the double-slit interference condition dsin⁡θ=mλd \sin\theta = m\lambda (which identifies maxima). Setting m=1m = 1 in asin⁡θ=mλa\sin\theta = m\lambda defines the boundary edge of the central maximum, not its center.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the half-width (distance from central peak to first minimum) with the total width of the central maximum, omitting the factor of 2.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    w_1 = λ⋅La1\frac{\lambda \cdot L}{a_1} = (650×10−9 m)⋅(1.50 m)(0.200×10−3 m)\frac{(650 \times 10^{-9}\text{ m}) \cdot (1.50\text{ m})}{(0.200 \times 10^{-3}\text{ m})} ⟹ w_1 = 4.88 ×\times 10^{-3} m\text{ m} = 4.88 mm\text{ mm}

    Correct

    w_1 = 2λLa1\frac{2\lambda L}{a_1} = 2(650×10−9 m)(1.50 m)0.200×10−3 m\frac{2(650 \times 10^{-9}\text{ m})(1.50\text{ m})}{0.200 \times 10^{-3}\text{ m}} = 9.75 ×\times 10^{-3} m\text{ m} = 9.75 mm\text{ mm}

    You calculated the distance from the center of the pattern to the first minimum (the half-width y1y_1), but the full width of the central maximum spans from the first minimum on one side (−y1-y_1) to the first minimum on the other side (+y1+y_1), which requires a factor of 22.

  2. Step 2

    w_2 = λ⋅La2\frac{\lambda \cdot L}{a_2} = (650×10−9 m)⋅(1.50 m)(0.0500×10−3 m)\frac{(650 \times 10^{-9}\text{ m}) \cdot (1.50\text{ m})}{(0.0500 \times 10^{-3}\text{ m})} ⟹ w_2 = 1.95 ×\times 10^{-2} m\text{ m} = 19.5 mm\text{ mm}

    Correct

    w_2 = 2λLa2\frac{2\lambda L}{a_2} = 2(650×10−9 m)(1.50 m)0.0500×10−3 m\frac{2(650 \times 10^{-9}\text{ m})(1.50\text{ m})}{0.0500 \times 10^{-3}\text{ m}} = 3.90 ×\times 10^{-2} m\text{ m} = 39.0 mm\text{ mm}

    You repeated the half-width calculation here. Including the factor of 22 gives w2=39.0 mmw_2 = 39.0\text{ mm}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the inverse proportionality between slit width and pattern spreading.

You converted nanometers and millimeters into meters accurately in standard scientific notation.

You executed the arithmetic and rounding with great precision.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Half-width vs. full-width confusion

You solved for the distance from the center to the first dark fringe instead of multiplying by 2 to obtain the full boundary-to-boundary width.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

The diffraction minimum condition asin⁡θ=mλa\sin\theta = m\lambda with m=1m=1 locates the edge of the central maximum relative to the center (y1=λLay_1 = \frac{\lambda L}{a}). The full central band spans between m=−1m = -1 and m=+1m = +1, so its total linear width is w=2y1=2λLaw = 2y_1 = \frac{2\lambda L}{a}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Define the boundaries of the central maximum
  • The central maximum of a single-slit diffraction pattern lies between the first minimum on either side: y∈[−y1,+y1]y \in [-y_1, +y_1].

  • Always multiply the single-minimum distance y1=λLay_1 = \frac{\lambda L}{a} by 22 when asked for the total or full width of the central maximum.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the full width of the central maximum as w=2y1=2λLaw = 2y_1 = \frac{2\lambda L}{a}.

  2. Calculate w1=2(650×10−9 m)(1.50 m)0.200×10−3 m=9.75×10−3 m=9.75 mmw_1 = \frac{2(650 \times 10^{-9}\text{ m})(1.50\text{ m})}{0.200 \times 10^{-3}\text{ m}} = 9.75 \times 10^{-3}\text{ m} = 9.75\text{ mm}.

  3. Calculate w2=2(650×10−9 m)(1.50 m)0.0500×10−3 m=3.90×10−2 m=39.0 mmw_2 = \frac{2(650 \times 10^{-9}\text{ m})(1.50\text{ m})}{0.0500 \times 10^{-3}\text{ m}} = 3.90 \times 10^{-2}\text{ m} = 39.0\text{ mm}.

Final answer

For a1=0.200 mma_1 = 0.200\text{ mm}, w1=9.75 mmw_1 = 9.75\text{ mm}; for a2=0.0500 mma_2 = 0.0500\text{ mm}, w2=39.0 mmw_2 = 39.0\text{ mm}.

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch the intensity profile of single-slit diffraction and mark −y1-y_1, 00, and +y1+y_1 to visually verify why the total width is 2y12y_1.

  • Double-check problem wording to see whether 'half-width' (center to minimum) or 'full width' (minimum to minimum) is requested.

OverviewACEpath Teacher's Diagnosis

02 The student assumes direct geometric proportionality between slit width and beam width, incorrectly writing w = a·L instead of applying wave diffraction.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    w1=a1⋅Lλ=(0.200×10−3 m)⋅(1.50 m)650×10−9 m=462 mw_1 = \frac{a_1 \cdot L}{\lambda} = \frac{(0.200 \times 10^{-3}\text{ m}) \cdot (1.50\text{ m})}{650 \times 10^{-9}\text{ m}} = 462\text{ m}

    Correct

    w1=2λLa1=2(6.50×10−7 m)(1.50 m)2.00×10−4 m=9.75×10−3 m=9.75 mmw_1 = \frac{2\lambda L}{a_1} = \frac{2(6.50 \times 10^{-7}\text{ m})(1.50\text{ m})}{2.00 \times 10^{-4}\text{ m}} = 9.75 \times 10^{-3}\text{ m} = 9.75\text{ mm}

    You inverted the positions of slit width a1a_1 and wavelength λ\lambda. The first diffraction minimum satisfies a1sin⁡θ=λ≈a1yLa_1 \sin\theta = \lambda \approx a_1 \frac{y}{L}, which leads to half-width y=λLa1y = \frac{\lambda L}{a_1} and total width w1=2λLa1w_1 = \frac{2\lambda L}{a_1}. Your formula also yielded an unphysical pattern width of 462 m462\text{ m} on a screen only 1.50 m1.50\text{ m} away.

  2. Step 2

    w2=a2⋅Lλ=(0.0500×10−3 m)⋅(1.50 m)650×10−9 m=115 mw_2 = \frac{a_2 \cdot L}{\lambda} = \frac{(0.0500 \times 10^{-3}\text{ m}) \cdot (1.50\text{ m})}{650 \times 10^{-9}\text{ m}} = 115\text{ m}

    Correct

    w2=2λLa2=2(6.50×10−7 m)(1.50 m)5.00×10−5 m=3.90×10−2 m=39.0 mmw_2 = \frac{2\lambda L}{a_2} = \frac{2(6.50 \times 10^{-7}\text{ m})(1.50\text{ m})}{5.00 \times 10^{-5}\text{ m}} = 3.90 \times 10^{-2}\text{ m} = 39.0\text{ mm}

    You applied the same inverted formula to the second slit width. Narrowing the slit causes wave diffraction to spread more widely, so the central maximum must broaden from 9.75 mm9.75\text{ mm} to 39.0 mm39.0\text{ mm}, rather than shrink.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted all quantities into SI units (0.200×10−3 m0.200\times 10^{-3}\text{ m}, 0.0500×10−3 m0.0500\times 10^{-3}\text{ m}, and 650×10−9 m650\times 10^{-9}\text{ m}).

You correctly identified that the central band width depends on the slit width, screen distance, and wavelength.

You carried out the arithmetic for your chosen formulas without calculation slips.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Diffraction Formula

You placed the slit width aa in the numerator and the wavelength λ\lambda in the denominator instead of writing w=2λLaw = \frac{2\lambda L}{a}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You relied on an inverted algebraic rearrangement or geometric optics intuition (that smaller apertures create narrower beams). In wave optics, the angular spread of diffraction is inversely proportional to the aperture size (θ≈λa\theta \approx \frac{\lambda}{a}), meaning a narrower opening forces light waves to spread out wider.

REASONING PATH
Your ACEpath teacher’s suggested approach
Derive from the diffraction minimum condition
  • asin⁡θ=mλa\sin\theta = m\lambda with m=±1m = \pm 1 gives the boundary of the central peak.

  • Use the small-angle approximation sin⁡θ≈yL\sin\theta \approx \frac{y}{L} to solve for half-width y=λLay = \frac{\lambda L}{a}, yielding full width w=2y=2λLaw = 2y = \frac{2\lambda L}{a}.

Perform a physical reality check
  • Diffraction patterns on laboratory benches span millimeters or centimeters, not hundreds of meters.

  • Check whether narrowing the slit widens the pattern (w∝1aw \propto \frac{1}{a}) and confirm that calculated dimensions are physically reasonable for the given screen distance.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the first minimum condition: a1sin⁡θ1=λ  ⟹  a1(w1/2L)=λa_1 \sin\theta_1 = \lambda \implies a_1\left(\frac{w_1 / 2}{L}\right) = \lambda

  2. Solve for full linear width: w1=2λLa1=2(6.50×10−7 m)(1.50 m)2.00×10−4 m=9.75×10−3 m=9.75 mmw_1 = \frac{2\lambda L}{a_1} = \frac{2(6.50 \times 10^{-7}\text{ m})(1.50\text{ m})}{2.00 \times 10^{-4}\text{ m}} = 9.75 \times 10^{-3}\text{ m} = 9.75\text{ mm}

  3. Repeat for the narrower slit: w2=2λLa2=2(6.50×10−7 m)(1.50 m)5.00×10−5 m=3.90×10−2 m=39.0 mmw_2 = \frac{2\lambda L}{a_2} = \frac{2(6.50 \times 10^{-7}\text{ m})(1.50\text{ m})}{5.00 \times 10^{-5}\text{ m}} = 3.90 \times 10^{-2}\text{ m} = 39.0\text{ mm}

  4. Compare the two widths: w2w1=39.0 mm9.75 mm=4\frac{w_2}{w_1} = \frac{39.0\text{ mm}}{9.75\text{ mm}} = 4, showing that narrowing the slit by a factor of 44 broadens the central maximum by a factor of 44.

Final answer

w1=9.75 mmw_1 = 9.75\text{ mm}, w2=39.0 mmw_2 = 39.0\text{ mm}; narrowing the slit by a factor of 44 quadruples the width of the central maximum.

NEXT STEPS
Final Takeaways from Your Teacher
  • Derive w=2λLaw = \frac{2\lambda L}{a} directly from the condition for the first dark fringe (asin⁡θ=λa\sin\theta = \lambda) instead of memorizing the formula from memory.

  • Always check whether narrowing an aperture causes diffraction broadening (w∝1aw \propto \frac{1}{a}) before computing numerical values.

OverviewACEpath Teacher's Diagnosis

03 The student fails to convert the slit width from millimeters to meters, resulting in a width that is off by a factor of 1000.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    w1=2⋅λ⋅La1w_1 = \frac{2\cdot \lambda \cdot L}{a_1}

  2. Step 2

    w1=2⋅(650×10−9 m)⋅(1.50 m)0.200  ⟹  w1=9.75×10−6 m=0.00975 mmw_1 = \frac{2\cdot (650\times 10^{-9}\text{ m})\cdot (1.50\text{ m})}{0.200} \implies w_1 = 9.75\times 10^{-6}\text{ m} = 0.00975\text{ mm}

    Correct

    w1=2(650×10−9 m)(1.50 m)0.200×10−3 m=9.75×10−3 m=9.75 mmw_1 = \frac{2(650\times 10^{-9}\text{ m})(1.50\text{ m})}{0.200\times 10^{-3}\text{ m}} = 9.75\times 10^{-3}\text{ m} = 9.75\text{ mm}

    You did not convert a1=0.200 mma_1 = 0.200\text{ mm} into meters (2.00×10−4 m2.00\times 10^{-4}\text{ m}), which caused your result to be too small by a factor of 10310^3.

  3. Step 3

    w2=2⋅λ⋅La2  ⟹  w2=2⋅(650×10−9 m)⋅(1.50 m)0.0500  ⟹  w2=3.90×10−5 m=0.0390 mmw_2 = \frac{2\cdot \lambda \cdot L}{a_2} \implies w_2 = \frac{2\cdot (650\times 10^{-9}\text{ m})\cdot (1.50\text{ m})}{0.0500} \implies w_2 = 3.90\times 10^{-5}\text{ m} = 0.0390\text{ mm}

    Correct

    w2=2(650×10−9 m)(1.50 m)0.0500×10−3 m=3.90×10−2 m=39.0 mmw_2 = \frac{2(650\times 10^{-9}\text{ m})(1.50\text{ m})}{0.0500\times 10^{-3}\text{ m}} = 3.90\times 10^{-2}\text{ m} = 39.0\text{ mm}

    You repeated the unit conversion error by substituting a2a_2 as 0.05000.0500 rather than 5.00×10−5 m5.00\times 10^{-5}\text{ m}, leading to a value that is again off by a factor of 10001000.

WHAT YOU DID WELL
Compliments from Your Teacher

You selected the correct physical relationship w=2λLaw = \frac{2\lambda L}{a} for the full width of the central diffraction peak.

You converted the laser wavelength from nanometers to meters accurately as 650×10−9 m650\times 10^{-9}\text{ m}.

You correctly observed the inverse proportionality showing that narrowing the slit broadens the pattern.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Omission

You substituted the slit widths in millimeters directly into an equation where the numerator was already expressed in meters.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Inconsistent unit tracking across formula terms: while you converted nanometers to meters in the numerator, you treated the numerical millimeter value in the denominator as if it were already in SI base units.

REASONING PATH
Your ACEpath teacher’s suggested approach
Convert All Lengths to SI Base Units First
  • Every distance term in wave optics formulas (aa, λ\lambda, LL, yy, ww) must share the same length unit—consistently meters (m\text{m}) before evaluating.

  • Write down an explicit conversion line: a1=0.200 mm=0.200×10−3 ma_1 = 0.200\text{ mm} = 0.200\times 10^{-3}\text{ m} and a2=0.0500 mm=0.0500×10−3 ma_2 = 0.0500\text{ mm} = 0.0500\times 10^{-3}\text{ m}.

Perform a Dimensional Unit Check
  • Carrying units through intermediate calculations: m⋅mmm=103 m\frac{\text{m}\cdot\text{m}}{\text{mm}} = 10^3\text{ m}, not m\text{m}.

  • Ensure that the denominator has unit m\text{m} so that m⋅mm=m\frac{\text{m}\cdot\text{m}}{\text{m}} = \text{m} cancels cleanly.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert slit widths to meters: a1=0.200 mm=2.00×10−4 ma_1 = 0.200\text{ mm} = 2.00\times 10^{-4}\text{ m} and a2=0.0500 mm=5.00×10−5 ma_2 = 0.0500\text{ mm} = 5.00\times 10^{-5}\text{ m}.

  2. Compute the initial central width: w1=2(6.50×10−7 m)(1.50 m)2.00×10−4 m=9.75×10−3 m=9.75 mmw_1 = \frac{2(6.50\times 10^{-7}\text{ m})(1.50\text{ m})}{2.00\times 10^{-4}\text{ m}} = 9.75\times 10^{-3}\text{ m} = 9.75\text{ mm}.

  3. Compute the narrowed slit central width: w2=2(6.50×10−7 m)(1.50 m)5.00×10−5 m=3.90×10−2 m=39.0 mmw_2 = \frac{2(6.50\times 10^{-7}\text{ m})(1.50\text{ m})}{5.00\times 10^{-5}\text{ m}} = 3.90\times 10^{-2}\text{ m} = 39.0\text{ mm}.

  4. Compare the widths: w2w1=39.0 mm9.75 mm=4\frac{w_2}{w_1} = \frac{39.0\text{ mm}}{9.75\text{ mm}} = 4, demonstrating that reducing the slit width by a factor of 44 broadens the central beam by a factor of 44.

Final answer

w1=9.75 mmw_1 = 9.75\text{ mm} and w2=39.0 mmw_2 = 39.0\text{ mm}; narrowing the slit by a factor of 44 broadens the central maximum by a factor of 44.

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out a dedicated 'given values in SI units' table before writing algebraic formulas.

  • Include unit symbols inside each fraction substitution to immediately spot mismatched prefixes like nm\text{nm} or mm\text{mm}.

  • Perform a sanity check on the scale: diffraction patterns on a screen 1.5 m1.5\text{ m} away typically have central maximum widths on the order of millimeters to centimeters, not fractions of a micron.

Lock it in

Similar question

01

Light of wavelength λ=500 nm\lambda = 500\text{ nm} passes through a single slit of width a=0.10 mma = 0.10\text{ mm} onto a screen 2.0 m2.0\text{ m} away. Calculate the full linear width of the central bright fringe.

Answer

w=2.0×10−2 mw = 2.0\times 10^{-2}\text{ m} (20 mm20\text{ mm}). Key step: w=2λLa=2(5.00×10−7 m)(2.0 m)1.0×10−4 m=0.020 mw = \frac{2\lambda L}{a} = \frac{2(5.00 \times 10^{-7}\text{ m})(2.0\text{ m})}{1.0 \times 10^{-4}\text{ m}} = 0.020\text{ m}.

02

A single-slit diffraction pattern is formed on a screen 1.20 m1.20\text{ m} away using a laser with λ=632.8 nm\lambda = 632.8\text{ nm}. If the measured total width of the central maximum is 15.2 mm15.2\text{ mm}, find the width of the slit aa.

Answer

a=1.00×10−4 ma = 1.00 \times 10^{-4}\text{ m} (0.100 mm0.100\text{ mm}). Key step: Rearrange w=2λLaw = \frac{2\lambda L}{a} to solve for a=2λLw=2(6.328×10−7 m)(1.20 m)0.0152 m≈1.00×10−4 ma = \frac{2\lambda L}{w} = \frac{2(6.328 \times 10^{-7}\text{ m})(1.20\text{ m})}{0.0152\text{ m}} \approx 1.00 \times 10^{-4}\text{ m}.

03

In a single-slit experiment, the distance between the two first-order minima is 16.0 mm16.0\text{ mm}. What will this distance become if the slit width is doubled and the screen distance is tripled simultaneously?

Answer

24.0 mm24.0\text{ mm}. Key step: The distance between the two first minima is the full width w=2λLa∝Law = \frac{2\lambda L}{a} \propto \frac{L}{a}. The new width is w′=w⋅L′/La′/a=16.0 mm⋅32=24.0 mmw' = w \cdot \frac{L'/L}{a'/a} = 16.0\text{ mm} \cdot \frac{3}{2} = 24.0\text{ mm}.

Loading workspace…