Resources

A student inspecting a horizontal irrigation conduit of uniform diameter DD observes that the pressure drops significantly along the pipe from Pin=2.50×105 PaP_{\text{in}} = 2.50 \times 10^5\text{ Pa} to Pout=1.10×105 PaP_{\text{out}} = 1.10 \times 10^5\text{ Pa} due to fluid friction over a length of L=50.0 mL = 50.0\text{ m}. The student claims that because pressure decreases along the flow path, the fluid must be accelerating so that vout>vinv_{\text{out}} > v_{\text{in}}. Evaluate this claim for an incompressible liquid (ρ=1000 kg/m3\rho = 1000\text{ kg/m}^3). If the uniform pipe diameter is D=5.00 cmD = 5.00\text{ cm} and the inlet speed is vin=2.00 m/sv_{\text{in}} = 2.00\text{ m/s}, calculate the true exit velocity voutv_{\text{out}} and identify the correct physical mechanism responsible for the pressure drop.

Answer and steps

Final answer

The student's claim is false; vout=2.00 m/sv_{\text{out}} = 2.00\text{ m/s} (constant speed). The pressure drop represents viscous mechanical energy dissipation into thermal internal energy, not kinetic energy acceleration.

Steps

01

Apply the Continuity Equation to Determine the Exit Speed

For any steady flow of an incompressible fluid (constant density ρ\rho), mass conservation is governed by the continuity equation:

Ainvin=AoutvoutA_{\text{in}} v_{\text{in}} = A_{\text{out}} v_{\text{out}}

where AA is the cross-sectional area of the pipe and vv is the average flow velocity.

The pipe has a uniform circular cross-section of diameter D=5.00 cmD = 5.00\text{ cm} over its entire length:

Ain=Aout=πD24A_{\text{in}} = A_{\text{out}} = \frac{\pi D^2}{4}

Substituting Ain=AoutA_{\text{in}} = A_{\text{out}} into the continuity equation gives:

vout=vin=2.00 m/sv_{\text{out}} = v_{\text{in}} = 2.00\text{ m/s}

Because the fluid is incompressible and the conduit diameter is uniform, the speed of the fluid cannot change.


02

Evaluate the Student's Claim

  • The claim is incorrect.
  • The student misapplies Bernoulli's principle for frictionless (inviscid) flow: P+12ρv2+ρgy=constantP + \frac{1}{2}\rho v^2 + \rho g y = \text{constant} Under Bernoulli's principle, a drop in pressure along a horizontal streamline (y=constanty = \text{constant}) corresponds to an increase in kinetic energy. However, Bernoulli's equation is only valid when viscous losses are negligible.

03

Identify the Physical Mechanism Responsible for the Pressure Drop

In a real fluid flowing through a real pipe:

  1. Viscous Shear and Friction: Fluid layers slide past one another and rub against the pipe walls, exerting viscous shear stresses that oppose the flow.
  2. Energy Dissipation: Overcoming this internal and boundary friction requires work. The pressure gradient ΔPL\frac{\Delta P}{L} provides the net forward force needed to sustain the motion against friction.
  3. Energy Conversion: Instead of being converted into kinetic energy (acceleration), the lost pressure energy (mechanical energy) is irreversibly dissipated as thermal internal energy (heat) within the fluid and pipe walls.

Therefore, the pressure drop is entirely due to viscous dissipation, and the fluid travels at a constant velocity of vout=2.00 m/sv_{\text{out}} = 2.00\text{ m/s}.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misapplies Bernoulli's equation to viscous flow, believing the pressure drop directly converts into kinetic energy.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Pin+12ρvin2=Pout+12ρvout2  ⟹  2.50×105+12(1000)(2.00)2=1.10×105+500vout2  ⟹  252000=110000+500vout2  ⟹  vout2=284P_{\text{in}} + \frac{1}{2}\rho v_{\text{in}}^2 = P_{\text{out}} + \frac{1}{2}\rho v_{\text{out}}^2 \implies 2.50 \times 10^5 + \frac{1}{2}(1000)(2.00)^2 = 1.10 \times 10^5 + 500 v_{\text{out}}^2 \implies 252000 = 110000 + 500 v_{\text{out}}^2 \implies v_{\text{out}}^2 = 284

    Correct

    Ainvin=Aoutvout  ⟹  vout=vin=2.00 m/sA_{\text{in}}v_{\text{in}} = A_{\text{out}}v_{\text{out}} \implies v_{\text{out}} = v_{\text{in}} = 2.00\text{ m/s}

    You applied Bernoulli's equation, which assumes frictionless, inviscid flow with no mechanical energy loss. Because the fluid is incompressible and the conduit diameter is uniform along its entire length, the continuity equation requires Ain=AoutA_{\text{in}} = A_{\text{out}}, so the fluid cannot change speed.

  2. Step 2

    vout=16.9 m/sv_{\text{out}} = 16.9\text{ m/s}, so the student's claim that fluid accelerates is correct.

    Correct

    vout=2.00 m/sv_{\text{out}} = 2.00\text{ m/s}; the student's claim is false.

    Because this calculation was based on the misapplied Bernoulli relation from Step 1, your derived exit velocity and evaluation of the claim are incorrect.

  3. Step 3

    The pressure drop is caused by the conversion of pressure energy into kinetic energy as the fluid speeds up.

    Correct

    The pressure drop is caused by viscous shear stresses (internal fluid friction and wall drag) dissipating mechanical energy irreversibly into thermal energy.

    Because the velocity is constant, the kinetic energy does not increase. The net forward force provided by the pressure drop balances viscous resistance, dissipating mechanical energy as thermal internal energy.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly evaluated the arithmetic within the formula you set up.

You showed clear, organized algebraic work from your starting assumption.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Misapplication of Bernoulli's Principle to Viscous Flow

No, this was not a simple arithmetic slip; it was a fundamental confusion between ideal Bernoulli flow and viscous pipe flow governed by continuity.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that a pressure drop along a streamline necessarily implies an acceleration of the fluid by invoking Bernoulli's principle. However, mass continuity (A1v1=A2v2A_1 v_1 = A_2 v_2) strictly constrains the velocity of an incompressible fluid regardless of pressure. When friction is present, pressure decreases to overcome viscous resistance without altering flow speed in a uniform conduit.

REASONING PATH
Your ACEpath teacher’s suggested approach
Continuity Governs Velocity
  • For an incompressible fluid in steady flow, A1v1=A2v2A_1 v_1 = A_2 v_2. If the cross-sectional area is uniform, the speed is constant everywhere along the pipe.

  • Always apply mass conservation first to find fluid velocities before considering energy balances.

Bernoulli vs. Viscous Flow
  • Bernoulli's equation applies only to inviscid flow without mechanical energy losses. In real pipe flow with friction, mechanical energy is dissipated as heat.

  • Do not equate initial and final total mechanical head when friction or head loss is present.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the continuity equation for an incompressible fluid: Ainvin=AoutvoutA_{\text{in}}v_{\text{in}} = A_{\text{out}}v_{\text{out}}.

  2. Because the pipe has a uniform circular cross-section, Ain=Aout=πD24A_{\text{in}} = A_{\text{out}} = \frac{\pi D^2}{4}, which gives vout=vin=2.00 m/sv_{\text{out}} = v_{\text{in}} = 2.00\text{ m/s}.

  3. Recognize that since the speed is constant, the kinetic energy does not change, disproving the claim that the fluid accelerates.

  4. Identify the pressure drop ΔP=1.40×105 Pa\Delta P = 1.40 \times 10^5\text{ Pa} as the work required to overcome internal viscous shear and wall friction, irreversibly converting mechanical energy into thermal energy.

Final answer

The claim is false; vout=2.00 m/sv_{\text{out}} = 2.00\text{ m/s}. The pressure drop is caused by viscous friction dissipating mechanical energy into thermal energy.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the conditions under which Bernoulli's equation is valid versus the extended energy equation with head loss.

  • Practice using the continuity equation as the primary constraint on flow velocity for incompressible fluids in ducts and pipes.

OverviewACEpath Teacher's Diagnosis

02 The student confuses the Hagen-Poiseuille pressure drop formula with an acceleration equation, solving for an exit velocity proportional to the pressure gradient.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ΔP=Pin−Pout=2.50×105−1.10×105=1.40×105 Pa\Delta P = P_{\text{in}} - P_{\text{out}} = 2.50 \times 10^5 - 1.10 \times 10^5 = 1.40 \times 10^5\text{ Pa}

  2. Step 2

    a=ΔPρ⋅L=1.40×1051000⋅50.0=2.80 m/s2a = \frac{\Delta P}{\rho \cdot L} = \frac{1.40 \times 10^5}{1000 \cdot 50.0} = 2.80\text{ m/s}^2

    Correct

    Ain=Aout  ⟹  vout=vin  ⟹  a=0 m/s2A_{\text{in}} = A_{\text{out}} \implies v_{\text{out}} = v_{\text{in}} \implies a = 0\text{ m/s}^2

    You assumed the pressure gradient represents an unbalanced net force that causes the fluid to accelerate. Because the fluid is incompressible and the pipe diameter is uniform, mass conservation prevents the fluid from speeding up along the pipe.

  3. Step 3

    vout2=vin2+2⋅a⋅L=(2.00)2+2⋅2.80⋅50.0=4.00+280=284  ⟹  vout=16.9 m/sv_{\text{out}}^2 = v_{\text{in}}^2 + 2 \cdot a \cdot L = (2.00)^2 + 2 \cdot 2.80 \cdot 50.0 = 4.00 + 280 = 284 \implies v_{\text{out}} = 16.9\text{ m/s}

    Correct

    vout=vin=2.00 m/sv_{\text{out}} = v_{\text{in}} = 2.00\text{ m/s}

    This calculation followed from your non-zero acceleration. Because the fluid does not accelerate, the true exit speed is equal to the inlet speed: vout=2.00 m/sv_{\text{out}} = 2.00\text{ m/s}.

  4. Step 4

    The claim is correct because the net pressure force accelerates the fluid along the pipe. The pressure drop is caused by an unbalanced net force driving fluid acceleration.

    Correct

    The claim is false. The pressure drop is caused by viscous shear stresses (internal fluid friction and wall friction) dissipating mechanical energy into thermal internal energy.

    The forward pressure force is exactly balanced by the opposing viscous friction along the pipe wall under steady flow, maintaining constant speed rather than causing acceleration.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the total pressure difference between the inlet and outlet of the conduit.

You applied kinematic formulas and Newton's second law consistently with your initial force balance assumption.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Confusing viscous pressure drop with net accelerating force in incompressible flow

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You overlooked the continuity constraint for incompressible fluids in a uniform pipe (A1v1=A2v2A_1 v_1 = A_2 v_2), incorrectly interpreting the pressure gradient as an unbalanced net force driving fluid acceleration rather than a force balancing viscous friction.

REASONING PATH
Your ACEpath teacher’s suggested approach
Apply Continuity First
  • For an incompressible fluid, A1v1=A2v2A_1 v_1 = A_2 v_2. If the cross-sectional area is constant (A1=A2A_1 = A_2), flow velocity must be constant (v1=v2v_1 = v_2).

  • Always verify whether geometry and incompressibility constrain the velocity before applying dynamical force balances.

Distinguish Viscous Loss from Kinetic Acceleration
  • In steady pipe flow, the pressure drop ΔP\Delta P overcomes viscous shear resistance τw\tau_w (friction against pipe walls); it does not accelerate the fluid.

  • Treat pressure drops in uniform pipes as viscous energy dissipation into heat, not as an increase in kinetic energy.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the continuity equation for an incompressible fluid: Ainvin=AoutvoutA_{\text{in}} v_{\text{in}} = A_{\text{out}} v_{\text{out}}.

  2. Note that the pipe cross-section is uniform: Ain=Aout=πD24A_{\text{in}} = A_{\text{out}} = \frac{\pi D^2}{4}.

  3. Conclude that vout=vin=2.00 m/sv_{\text{out}} = v_{\text{in}} = 2.00\text{ m/s}, meaning the fluid does not accelerate (a=0 m/s2a = 0\text{ m/s}^2).

  4. Identify that the forward force from ΔP\Delta P balances opposing viscous wall friction: Fpressure=Fviscous frictionF_{\text{pressure}} = F_{\text{viscous friction}}.

  5. State that the mechanical pressure energy is irreversibly converted into thermal energy.

Final answer

The claim is false; vout=2.00 m/sv_{\text{out}} = 2.00\text{ m/s}. The pressure drop is caused by viscous friction dissipating mechanical energy into thermal energy.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the continuity equation (Q=Av=constantQ = Av = \text{constant}) for incompressible fluids in pipes of uniform vs. varying diameter.

  • Contrast frictionless Bernoulli flow (where pressure drops correspond to kinetic or potential energy gains) with viscous real fluid flow (where pressure drops overcome friction at constant speed).

Lock it in

Similar question

01

Water (ho=1000 kg/m3 ho = 1000\text{ kg/m}^3) flows through a horizontal pipe of uniform radius r=4.0 cmr = 4.0\text{ cm} at a steady rate of 0.020 m3/s0.020\text{ m}^3/\text{s}. The pressure drops by 3.0×104 Pa3.0 \times 10^4\text{ Pa} between two points separated by 20 m20\text{ m}. Find the flow speed at both points.

Answer

The speed is 3.98 m/s3.98\text{ m/s} at both points. By continuity, v=QA=0.020π(0.040)2≈3.98 m/sv = \frac{Q}{A} = \frac{0.020}{\pi (0.040)^2} \approx 3.98\text{ m/s}. Because the pipe diameter is uniform, the speed does not change despite the pressure drop.

02

A horizontal duct narrows smoothly from a cross-sectional area of A1=0.10 m2A_1 = 0.10\text{ m}^2 to A2=0.05 m2A_2 = 0.05\text{ m}^2. Water enters at v1=3.0 m/sv_1 = 3.0\text{ m/s} with pressure P1=2.0×105 PaP_1 = 2.0 \times 10^5\text{ Pa}. Assuming ideal inviscid flow, calculate v2v_2 and P2P_2. Contrast this with a uniform duct that has a pressure drop.

Answer

v2=6.0 m/sv_2 = 6.0\text{ m/s} and P2=1.865×105 PaP_2 = 1.865 \times 10^5\text{ Pa}. By continuity, A1v1=A2v2  ⟹  v2=6.0 m/sA_1 v_1 = A_2 v_2 \implies v_2 = 6.0\text{ m/s}. By Bernoulli's equation, P2=P1+12ρ(v12−v22)=2.0×105−13500=1.865×105 PaP_2 = P_1 + \frac{1}{2}\rho(v_1^2 - v_2^2) = 2.0\times 10^5 - 13500 = 1.865 \times 10^5\text{ Pa}. In this converging duct, pressure drops because fluid genuinely accelerates due to area change, whereas in a uniform duct, pressure drops due to viscous friction while speed stays constant.

03

Oil of density ρ=880 kg/m3\rho = 880\text{ kg/m}^3 flows at 1.5 m/s1.5\text{ m/s} through a horizontal pipe of uniform diameter. Over a 100 m100\text{ m} stretch, friction causes a pressure loss of ΔP=8.0×104 Pa\Delta P = 8.0 \times 10^4\text{ Pa}. Calculate the rate of mechanical energy dissipation (power lost to heat) if the pipe cross-sectional area is 0.0080 m20.0080\text{ m}^2.

Answer

960 W960\text{ W}. The volumetric flow rate is Q=Av=0.0080×1.5=0.012 m3/sQ = A v = 0.0080 \times 1.5 = 0.012\text{ m}^3/\text{s}. The dissipated power is Pdiss=QΔP=0.012 m3/s×8.0×104 Pa=960 WP_{\text{diss}} = Q \Delta P = 0.012\text{ m}^3/\text{s} \times 8.0 \times 10^4\text{ Pa} = 960\text{ W}. All lost pressure work is converted directly into thermal internal energy.

Loading workspace…