Resources
An underwater hydrophone calibrated to the oceanographic standard reference intensity (corresponding to a reference pressure in seawater) measures a continuous acoustic signal from a sonar beacon with an intensity of . (a) Determine the sound intensity level in underwater decibels relative to . (b) Determine the sound intensity level of this same physical wave if evaluated against the standard airborne hearing reference threshold .
Answer and steps
Final answer
(a) ; (b)
Steps
Sound Intensity Level in Underwater Decibels
Understanding the Decibel Scale and Reference Intensities
The sound intensity level in decibels () quantifies the ratio of an acoustic wave's intensity to a specified baseline reference intensity on a logarithmic scale: Because decibels express a relative ratio rather than an absolute physical unit, the numerical value of depends directly on the chosen standard reference level .
Step-by-Step Derivation
-
Identify the given values:
- Sound wave intensity:
- Underwater reference intensity: (corresponding to )
- Calculate the ratio :
-
Compute the logarithm and scale by :
Thus:
Sound Intensity Level Relative to the Airborne Reference
-
Identify the airborne reference intensity:
- Airborne threshold of hearing: (corresponding to )
- Calculate the ratio :
-
Compute the logarithm and scale by :
Thus:
Important Pitfall to Avoid
A common mistake is directly comparing underwater decibel ratings to airborne decibel ratings without accounting for their different reference baselines. Because is roughly six orders of magnitude smaller than , the identical physical wave yields a decibel number approximately higher in water than in air.
Typical errors
01 The student misuses the pressure-level decibel multiplier of 20 instead of 10 for sound intensity level, doubling the decibel values.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You used a prefactor of rather than . Sound intensity level is based on power/intensity ratios and is defined with a prefactor of : . The factor of is only used when taking the logarithm of a sound pressure ratio () because .
- Step 2Correct
Your evaluation of was accurate, but multiplying by instead of carried the error forward into your final answer for part (a).
- Step 3Correct
You repeated the formula mistake by setting the prefactor to instead of for the intensity ratio in air.
- Step 4Correct
Your logarithm computation of was correct, but multiplying by doubled the correct decibel level.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified and substituted the given wave intensity and both reference intensities into the ratio arguments.
You accurately evaluated the base-10 logarithms for both calculations.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally applied the sound pressure level formula prefactor of to an intensity ratio.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the decibel multiplier for power-like quantities (such as intensity , which uses ) with field-like quantities (such as pressure amplitude , which uses because ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Decibel Prefactor Rule
For intensity or power: . For pressure or voltage: .
Always check the units of the ratio: if using , multiply the logarithm by ; if using , multiply by .
CORRECTED PATH
ACEpath Teacher's DemonstrationRecalculate part (a) with the factor of : .
Recalculate part (b) with the factor of : .
(a) ; (b)
02 The student uses natural logarithm (ln) instead of common base-10 logarithm (log10) in the decibel formula.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The decibel scale is based on powers of ten and defined using the common base-10 logarithm, , rather than the natural logarithm, .
- Step 2Correct
Evaluating with yields .
- Step 3Correct
This step repeats the use of the natural logarithm instead of .
- Step 4Correct
Evaluating with yields .
WHAT YOU DID WELL
Compliments from Your TeacherYou selected the correct reference intensity values for both seawater and airborne sound levels.
You formed the correct intensity ratios inside the logarithmic argument.
You accurately evaluated your written algebraic expressions on your calculator.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of in the definition of sound intensity level.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisThe bel unit represents an order of magnitude (a factor of 10) in intensity, making the decibel one-tenth of a bel (). Because the scale is fundamentally constructed on base-10 orders of magnitude, all decibel calculations require the common base-10 logarithm , not the base- natural logarithm .
REASONING PATH
Your ACEpath teacher’s suggested approach- Decibel Definition
Sound intensity level in decibels is always defined as .
Check your calculator input and written formula to verify you are pressing the (base 10) key rather than the (base ) key.
- Order of Magnitude Sanity Check
An intensity ratio of must correspond exactly to .
For Part (b), note that , which is between () and (). An answer near immediately signals that an incorrect logarithm base was used.
CORRECTED PATH
ACEpath Teacher's DemonstrationFor underwater:
Compute the base-10 logarithm:
For air:
Compute the base-10 logarithm:
(a) ; (b)
03 The student swaps the reference intensity and the measured intensity in the decibel formula, resulting in a negative decibel level.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The sound intensity level formula measures how many times greater the signal intensity is compared to the baseline, so the measured intensity belongs in the numerator and the reference threshold belongs in the denominator.
- Step 2Correct
Your arithmetic on the inverted ratio was accurate, but because the ratio was flipped, your final value became instead of .
- Step 3Correct
Here, you repeated the inverted ratio instead of using .
- Step 4Correct
Your calculation correctly evaluated the expression you wrote, but propagating the inverted fraction gave a negative decibel level instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified both reference intensities and from the problem statement.
You correctly applied base-10 logarithmic computation and scaled by a factor of .
You maintained high arithmetic precision throughout your intermediate calculations.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou placed the baseline reference intensity in the numerator and the actual wave intensity in the denominator. In physics level definitions (decibels, optical density, Richter scale), the measured signal is always compared relative to the reference base (). When , the decibel value must be positive.
REASONING PATH
Your ACEpath teacher’s suggested approach- Formula Direction
, where is the measured intensity and is the reference intensity.
Check whether the physical sound is louder than the baseline reference. If , ensure the fraction is greater than so that .
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the standard sound intensity level formula: .
Substitute and : .
Substitute and : .
(a) ; (b)
Lock it in
What is the general formula for sound intensity level in decibels when given an acoustic intensity and reference intensity ?
. Intensity is a power-related quantity, so the multiplier is always , never .
Similar question
A loudspeaker emits sound with an intensity of . Calculate its sound intensity level in decibels relative to the airborne threshold .
Answer
.
An ocean acoustic experiment measures an intensity level of using . What is the absolute intensity of the acoustic wave in ?
Answer
Using . Thus .
A sound wave has an acoustic pressure amplitude of . (a) Calculate the sound pressure level in air relative to . (b) If the corresponding intensity in air is , verify whether gives the same decibel value.
Answer
(a) . (b) . Both formulas yield , confirming that and describe the same acoustic level.