Resources
An unknown pure monoatomic substance of molar mass is observed at a temperature of and standard pressure . In this state, particles move independently in straight lines between brief elastic collisions. Laboratory measurements reveal that the mean free path of the particles is . Modeling the particles as hard spheres of effective collision diameter , and using the kinetic theory relation where is the number density and , reverse-engineer the effective microscopic collision diameter of a single particle in picometers ().
Answer and steps
Final answer
.
Steps
Calculate the Number Density
To determine the effective collision diameter of a single gas particle from its mean free path, we combine the ideal gas law with the kinetic theory model of collisions.
In the kinetic theory of gases, the particles are modeled as moving independently in straight lines between brief elastic collisions. The number density (the number of particles per unit volume) is related to pressure and absolute temperature by the ideal gas law:
Substitute the given values into the equation:
Relate Mean Free Path to Collision Diameter
The mean free path represents the average distance a particle travels between collisions. Considering that all particles are in motion, the expression for includes a relative velocity factor of :
Rearranging this formula to solve for the effective collision cross-sectional area factor :
Compute the Effective Diameter
Substitute the known values into the rearranged equation:
Evaluating the denominator:
Taking the reciprocal gives:
Taking the square root to solve for :
Convert to Picometers
Using the conversion factor :
(Common Pitfall: Omitting the geometric factor , which accounts for the target particles also moving rather than remaining stationary, underestimates the collision frequency and leads to an overestimation of .)
Typical errors
01 The student forgets the geometric factor of √2 in the mean free path formula, leading to an overestimated collision diameter.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the relative velocity factor in the denominator of the mean free path equation, which accounts for the motion of all target particles.
- Step 3Correct
Your arithmetic follows correctly from your formula, but the value is affected by the missing factor.
- Step 4Correct
Your unit conversion from meters to picometers is accurate, but the numerical result inherits the earlier omission.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the particle number density from the given temperature and pressure using the ideal gas law.
You accurately rearranged your algebraic formula to isolate and converted meters to picometers correctly.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou used the simplified formula for stationary target particles instead of the standard kinetic theory formula , forgetting that all gas particles are in thermal motion with an average relative speed of .
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify Target Particle Motion
If target gas particles are in thermal motion rather than fixed in space, the collision frequency increases by a factor of .
Always include in the denominator of the mean free path formula: .
- Check Cross-Sectional Geometry
The effective collision cross-section between two identical spheres of diameter is .
Combine the collision cross-section with relative velocity: .
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the complete kinetic theory equation for moving particles: .
Solve for : .
Substitute and : .
Convert to picometers: .
02 The student squares the mean free path relation to solve for d² but forgets to take the square root at the final step, reporting d² instead of d.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You reported the numerical value of as without taking the square root, and you appended the unit without multiplying by the conversion factor .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the particle number density using the ideal gas law.
You accurately rearranged the mean free path equation and accounted for the factor in the denominator.
You evaluated the value of in square meters correctly.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou stopped after computing and replaced the unit label directly with instead of taking the square root and applying the unit conversion.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisLosing track of the variable exponent ( vs. ) during multi-step algebraic isolation causes the final root-extraction and unit conversion steps to be overlooked.
REASONING PATH
Your ACEpath teacher’s suggested approach- Variable State Check
If a formula contains an exponent on the target variable (e.g., ), the isolated expression gives , not .
Always write explicitly before entering values into the calculator.
- Unit Dimensionality Check
A length cannot equal an area; converting to requires multiplying by .
Verify that your intermediate units match the target quantity before converting prefixes.
CORRECTED PATH
ACEpath Teacher's DemonstrationTake the square root of : .
Convert meters to picometers using : .
03 The student misapplies the metric conversion prefix for picometers by treating 1 pm as 10⁻⁹ m instead of 10⁻¹² m, resulting in a value off by a factor of 1000.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You equated to , which is the definition of a nanometer (). The SI prefix pico- () corresponds to .
- Step 4Correct
(or )
Because of the incorrect conversion factor in the previous step, your final answer in picometers is off by a factor of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the gas number density from the given pressure and temperature.
You accurately solved for the particle diameter in meters using the hard-sphere collision cross-section formula.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou mixed up the SI metric prefix pico- () with nano- ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Metric Prefixes for Small Length Scales
Remember: milli- () , micro- () , nano- () , pico- () , and femto- () .
Always double-check prefix letters before converting: 'n' stands for nano () and 'p' stands for pico ().
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the correct prefix conversion: , so .
Multiply your diameter in meters by : .
(or using unrounded intermediate values)
Lock it in
Why does the mean free path formula for a gas include a factor of in the denominator?
Because target molecules are also moving. The average relative velocity between colliding molecules is , which increases collision frequency.
Similar question
A gas has a number density of and an effective molecular diameter of . Calculate its mean free path .
Answer
Use . Compute the denominator: . Thus, ().
A sample of nitrogen gas at and has a measured mean free path of . Using , determine the effective collision diameter of a nitrogen molecule in picometers.
Answer
First find number density: . Next, solve for : .
An ideal gas container is compressed isothermally to one-fourth of its initial volume (). If the initial mean free path was , what is the new mean free path ? How would the calculated diameter change if you mistakenly believed number density remained constant?
Answer
Since , reducing volume to one-fourth increases number density by a factor of (). Because , the new mean free path is . If one erroneously assumed was unchanged while dropped to , the calculated diameter would be overestimated by a factor of .