Resources
An experimental freight cart is propelled from rest along a horizontal track by a compressed launcher spring with spring constant . The spring is initially compressed by . After leaving the spring at its equilibrium position, the cart travels across a horizontal rough patch of length with coefficient of kinetic friction . The cart then ascends a frictionless incline of angle above the horizontal until it momentarily comes to rest at a vertical height above the horizontal track. Neglect air resistance and rolling friction on the incline. Deduce the mass of the cart in kilograms. (Use .)
Answer and steps
Final answer
Steps
Identify the Energy Components
To find the mass of the cart, we apply the work-energy theorem between the initial release point and the highest point reached on the incline.
-
Initial State (): The cart is at rest against the fully compressed spring on the horizontal track.
- Kinetic energy:
- Elastic potential energy:
- Gravitational potential energy (taking the horizontal track as the reference level ):
-
Final State (): The cart momentarily comes to rest at height on the frictionless incline.
- Kinetic energy:
- Elastic potential energy: (the cart is detached from the spring)
- Gravitational potential energy:
Work Done by Non-Conservative Forces
Along the horizontal track, the normal force on the cart is . As the cart crosses the rough patch of length , kinetic friction does negative work:
Because the incline is frictionless and air resistance is negligible, no additional non-conservative work is done.
Apply the Work-Energy Theorem
The work done by non-conservative forces equals the change in total mechanical energy:
Rearranging the terms to isolate the initial elastic energy:
Solving for the mass :
Substitute the Given Values
Calculate the stored spring energy:
Calculate the effective vertical equivalent:
Evaluating the mass using standard local gravitational acceleration:
(Note: The incline angle determines the distance traveled along the slope, but because the incline is frictionless, the gravitational potential energy depends solely on the vertical height .)
Typical errors
01 The student forgets the square on the compression distance x when calculating the initial elastic potential energy.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The formula for the potential energy stored in an ideal Hooke's-law spring is . You wrote and evaluated , forgetting to square the compression distance .
- Step 2
- Step 3
- Step 4Correct
Your energy balance relation is conceptually sound, but it inherits the incorrect spring energy from Step 1.
- Step 5Correct
Your algebraic solution for is correct, but downstream from the initial calculation error in Step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that the initial elastic potential energy is converted into gravitational potential energy and work done against friction.
You correctly identified that normal force on the flat surface is and properly formulated the friction energy dissipation.
You correctly recognized that gravitational potential energy depends solely on the vertical height , independent of the slope angle .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of when calculating elastic potential energy.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating the linear relationship in Hooke's law force () with the quadratic relationship in stored elastic potential energy ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Elastic Potential Energy Formula
Stored spring potential energy is , representing the area under the linear force-displacement graph ().
Always verify dimensional units: , whereas carries units of Newtons (force), not Joules.
CORRECTED PATH
ACEpath Teacher's Demonstration(or with intermediate rounding)
02 The student incorrectly multiplies the vertical height h by sin(25.0°) assuming height along an incline must include the angle factor even though vertical height is already given.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Gravitational potential energy depends strictly on the true vertical elevation change, . Because the problem already defines as the vertical height, you should not multiply by . The incline angle is redundant extra information here.
- Step 4Correct
Your algebraic rearrangement and solving process followed logically from your equations, but this final result was affected by the extra sine factor in Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that total initial elastic energy equals the energy dissipated by friction plus the final gravitational potential energy.
You accurately computed the stored spring energy .
You correctly applied the horizontal normal force to express the friction work as .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou assumed that every incline problem requires multiplying the displacement by to find gravitational potential energy, overlooking that the problem statement directly gave the vertical height rather than the distance along the ramp.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identifying Vertical Height vs. Ramp Distance
Gravitational potential energy near Earth's surface is , where is strictly the vertical elevation above the reference line.
Check the given dimensions carefully: if a quantity is explicitly stated as 'vertical height', use it directly; only multiply by when given distance along the slope.
CORRECTED PATH
ACEpath Teacher's Demonstration03 The student neglects the thermal energy dissipated by friction, equating initial elastic potential energy directly to final gravitational potential energy.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
()kx^2 = mgh
CorrectYou assumed that mechanical energy is conserved throughout the entire motion. However, non-conservative kinetic friction does work as the cart crosses the rough patch, dissipating energy as thermal energy.
- Step 2
()(1850)(0.650)^2 = m(9.80)(4.10) 390.81 = 40.18m
CorrectYour numerical substitution and algebraic simplification followed your equation correctly, but the friction term was missing from the right-hand side.
- Step 3
m = = 9.73
CorrectYour final calculation is numerically consistent with your equation, but it differs from the correct answer because friction was omitted earlier.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the formulas for spring potential energy and gravitational potential energy.
You substituted the given values of , , , and accurately into your chosen equation.
You solved your linear equation for with correct arithmetic.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTreating a system with friction as an isolated, conservative system by equating initial potential energy directly to final potential energy without accounting for work done by non-conservative forces.
REASONING PATH
Your ACEpath teacher’s suggested approach- Account for Non-Conservative Work
When non-conservative forces like friction act over a distance , mechanical energy is not conserved: , or , where .
Always list all forces acting over each section of track and add the dissipated thermal energy to the final energy side before solving.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the work-energy theorem: , so .
Factor out : .
Substitute the known values: .
Evaluate both sides: .
Solve for the mass: .
Lock it in
What is the correct formula for the elastic potential energy stored in an ideal spring compressed or stretched by a distance ?
. The displacement must be squared because force increases linearly with distance ().
Similar question
A dart gun uses a spring with compressed by . If all stored elastic energy is converted into kinetic energy of a dart, find the launch speed .
Answer
. Initial energy is . Equating to kinetic energy: .
A block slides along a frictionless horizontal floor at and strikes a horizontal spring bumper with spring constant . What is the maximum compression of the spring?
Answer
. Initial kinetic energy is . At maximum compression, turns into spring energy: .
A package is launched horizontally from rest by a spring () compressed by . It slides across a rough horizontal patch of length with , then up a frictionless ramp inclined at . What vertical height does the package reach before stopping? (Use .)
Answer
. Initial energy . Friction work magnitude . Energy at top: . Height .