Resources

A small coin of mass m=0.0500 kgm = 0.0500\text{ kg} is released from rest at the top rim of a hemispherical bowl of radius R=0.800 mR = 0.800\text{ m}. As the coin slides down the smooth interior surface toward the bottom, a constant tangential friction force of magnitude fkf_k opposes its motion. Determine the threshold critical value of fkf_k such that the coin just barely reaches the bottom of the bowl with zero speed. Express the mechanical energy lost to friction over the quarter-circle path in this threshold limit. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

Threshold fk=0.312 Nf_k = 0.312\text{ N}; Mechanical energy dissipated ΔEmech=−0.392 J\Delta E_{\text{mech}} = -0.392\text{ J}

Steps

01

Identify the Forces and Trajectory

As the coin slides from the rim to the bottom of the hemispherical bowl:

  • The coin descends through a vertical height equal to the bowl's radius: h=R=0.800 mh = R = 0.800\text{ m}.
  • The path traveled along the bowl's inner circular surface is a quarter-circle of arc length: s=14(2πR)=πR2s = \frac{1}{4}(2\pi R) = \frac{\pi R}{2}
  • The normal force acts perpendicular to the surface at every point along the curved path, so it does no work: WN=0W_N = 0.
  • Gravity acts downward, doing positive work as the coin descends: Wg=mgh=mgRW_g = m g h = m g R
  • The constant friction force fkf_k always acts opposite to the direction of motion along the curved path, doing negative work: Wf=−fks=−fk(πR2)W_f = -f_k s = -f_k\left(\frac{\pi R}{2}\right)

02

Apply the Work-Energy Theorem

The work-energy theorem states that the net work done on the coin equals the change in its kinetic energy: Wnet=ΔK=Kf−KiW_{\text{net}} = \Delta K = K_f - K_i

The coin starts from rest at the top (Ki=0K_i = 0) and, at the threshold limit, arrives at the bottom with zero speed (Kf=0K_f = 0): Wg+Wf=0W_g + W_f = 0

Substitute the expressions for WgW_g and WfW_f: mgR−fk(πR2)=0m g R - f_k\left(\frac{\pi R}{2}\right) = 0

Divide both sides by RR (R≠0R \neq 0): mg−fkπ2=0  ⟹  fk=2mgπm g - f_k \frac{\pi}{2} = 0 \implies f_k = \frac{2mg}{\pi}

(Note on intermediate motion: At any intermediate angle θ\theta below the horizontal, the net energy is proportional to sin⁡θ−2πθ>0\sin\theta - \frac{2}{\pi}\theta > 0 for all 0<θ<π20 < \theta < \frac{\pi}{2}, confirming that the coin maintains forward velocity and does not stall before reaching the bottom.)

Substitute the given numerical values: fk=2⋅(0.0500 kg)⋅(9.80 m/s2)π=0.980π N≈0.312 Nf_k = \frac{2 \cdot (0.0500\text{ kg}) \cdot (9.80\text{ m/s}^2)}{\pi} = \frac{0.980}{\pi}\text{ N} \approx 0.312\text{ N}


03

Calculate the Mechanical Energy Dissipated

The change in total mechanical energy ΔEmech\Delta E_{\text{mech}} is equal to the work done by non-conservative forces (here, friction): ΔEmech=Wf=−fks\Delta E_{\text{mech}} = W_f = -f_k s

Because the coin comes to rest at the bottom, the magnitude of the work done by friction is exactly equal to the loss in gravitational potential energy: ΔEmech=−mgR\Delta E_{\text{mech}} = -m g R

Substitute the values: ΔEmech=−(0.0500 kg)⋅(9.80 m/s2)⋅(0.800 m)=−0.392 J\Delta E_{\text{mech}} = -(0.0500\text{ kg}) \cdot (9.80\text{ m/s}^2) \cdot (0.800\text{ m}) = -0.392\text{ J}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses the straight-line displacement R rather than the curved arc length (π / 2) * R to calculate the work done by friction.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Wnet=ΔK=0W_{\text{net}} = \Delta K = 0

  2. Step 2

    m⋅g⋅R−fk⋅R=0  ⟹  fk=m⋅g=0.0500⋅9.80  ⟹  fk=0.490 Nm \cdot g \cdot R - f_k \cdot R = 0 \implies f_k = m \cdot g = 0.0500 \cdot 9.80 \implies f_k = 0.490\text{ N}

    Correct

    mgR−fk(πR2)=0  ⟹  fk=2mgπ≈0.312 Nm g R - f_k\left(\frac{\pi R}{2}\right) = 0 \implies f_k = \frac{2mg}{\pi} \approx 0.312\text{ N}

    Gravity is a conservative force whose work depends only on the vertical drop h=Rh = R, but friction is a non-conservative tangential force whose work depends on the total distance traveled along the circular surface, s=πR2s = \frac{\pi R}{2}.

  3. Step 3

    ΔEloss=fk⋅R=0.490⋅0.800=0.392 J\Delta E_{\text{loss}} = f_k \cdot R = 0.490 \cdot 0.800 = 0.392\text{ J}

    Correct

    ΔEmech=−fks=−mgR=−0.392 J\Delta E_{\text{mech}} = -f_k s = -m g R = -0.392\text{ J}

    Your calculation yielded the correct magnitude for the mechanical energy lost because substituting your incorrect fk=mgf_k = mg back into fkRf_k R canceled out the missing factor of π2\frac{\pi}{2}, although mechanical energy change should be expressed as negative work or dissipated energy along the actual arc path.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the net work done equals the change in kinetic energy (Wnet=ΔK=0W_{\text{net}} = \Delta K = 0).

You correctly computed the work done by gravity using the vertical displacement h=Rh = R.

You correctly related the loss of mechanical energy to the work done against friction.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Straight-line displacement used instead of path length for friction

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating the displacement used for conservative forces (where only end-point coordinate changes matter) with the actual path length traversed for tangential friction forces.

REASONING PATH
Your ACEpath teacher’s suggested approach
Conservative vs. Non-conservative Work
  • For gravity, Wg=−mgΔyW_g = -m g \Delta y depends only on vertical displacement. For tangential friction, ∣Wf∣=fks|W_f| = f_k s, where ss is the total distance traveled along the path.

  • Always compute the arc length of the trajectory when calculating work done by a constant tangential friction force.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. The path is a quarter of a circle of radius RR, so the distance traveled is s=14(2πR)=πR2s = \frac{1}{4}(2\pi R) = \frac{\pi R}{2}.

  2. Apply the work-energy theorem: Wg+Wf=mgR−fk(πR2)=0W_g + W_f = m g R - f_k \left(\frac{\pi R}{2}\right) = 0.

  3. Solve for fkf_k: fk=2mgπ=2(0.0500 kg)(9.80 m/s2)π≈0.312 Nf_k = \frac{2mg}{\pi} = \frac{2(0.0500\text{ kg})(9.80\text{ m/s}^2)}{\pi} \approx 0.312\text{ N}.

  4. Calculate the mechanical energy dissipated: ΔEmech=Wf=−fks=−mgR=−(0.0500 kg)(9.80 m/s2)(0.800 m)=−0.392 J\Delta E_{\text{mech}} = W_f = -f_k s = -m g R = -(0.0500\text{ kg})(9.80\text{ m/s}^2)(0.800\text{ m}) = -0.392\text{ J}.

Final answer

Threshold fk=0.312 Nf_k = 0.312\text{ N}; Mechanical energy dissipated ΔEmech=−0.392 J\Delta E_{\text{mech}} = -0.392\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • When calculating work done by friction along a curved surface, explicitly sketch the trajectory and write down the arc length s=Rθs = R\theta before setting up your work-energy equation.

  • Remember that friction acts along the contour of motion at every instant, so its displacement is always the scalar distance traveled, never the straight-line displacement vector.

OverviewACEpath Teacher's Diagnosis

02 The student uses the full circumference 2 * π * R instead of the quarter-circle arc length (π / 2) * R for the path traveled.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    s=2⋅π⋅Rs = 2 \cdot \pi \cdot R

    Correct

    s=14(2πR)=πR2s = \frac{1}{4}(2\pi R) = \frac{\pi R}{2}

    Moving from the rim of a hemispherical bowl to its bottom covers a quarter of a full circle (90∘90^\circ or π2 rad\frac{\pi}{2}\text{ rad}), not a full circle (2πR2\pi R).

  2. Step 2

    m⋅g⋅R−fk⋅(2⋅π⋅R)=0  ⟹  fk=m⋅g2⋅π=0.0500⋅9.802⋅π=0.0780 Nm \cdot g \cdot R - f_k \cdot (2 \cdot \pi \cdot R) = 0 \implies f_k = \frac{m \cdot g}{2 \cdot \pi} = \frac{0.0500 \cdot 9.80}{2 \cdot \pi} = 0.0780\text{ N}

    Correct

    mgR−fk(πR2)=0  ⟹  fk=2mgπ=2(0.0500)(9.80)π≈0.312 Nm g R - f_k \left(\frac{\pi R}{2}\right) = 0 \implies f_k = \frac{2mg}{\pi} = \frac{2(0.0500)(9.80)}{\pi} \approx 0.312\text{ N}

    Your work-energy equation and algebra were carried out correctly, but the result for fkf_k is four times too small because of the incorrect path length substituted from Step 1.

  3. Step 3

    ΔELoss=m⋅g⋅R=0.0500⋅9.80⋅0.800=0.392 J\Delta E_{Loss} = m \cdot g \cdot R = 0.0500 \cdot 9.80 \cdot 0.800 = 0.392\text{ J}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that the net work on the coin equals zero because ΔK=0\Delta K = 0.

You properly evaluated the work done by gravity as Wg=mgRW_g = mgR.

You accurately computed the total mechanical energy lost to friction as mgR=0.392 JmgR = 0.392\text{ J}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect path length (full circumference instead of quarter-circle arc)

You substituted the full circumference 2πR2\pi R instead of the quarter-circle arc length πR2\frac{\pi R}{2}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating the total circumference of a full circular cross-section with the specific arc length traversed from the rim to the bottom of a hemisphere.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Arc Angle
  • The arc length along a circular path of radius RR through subtended angle θ\theta (in radians) is s=Rθs = R\theta.

  • Sketch the trajectory and check the angle subtended at the center: descending from a horizontal rim to the vertical bottom corresponds to θ=π2 rad\theta = \frac{\pi}{2}\text{ rad}, so s=πR2s = \frac{\pi R}{2}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Determine the actual path length traveled: s=Rθ=R(π2)=πR2s = R\theta = R\left(\frac{\pi}{2}\right) = \frac{\pi R}{2}.

  2. Apply the work-energy theorem with the corrected path length: Wnet=Wg+Wf=mgR−fks=0W_{\text{net}} = W_g + W_f = mgR - f_k s = 0.

  3. Substitute s=πR2s = \frac{\pi R}{2}: mgR−fk(πR2)=0  ⟹  fk=2mgπmgR - f_k\left(\frac{\pi R}{2}\right) = 0 \implies f_k = \frac{2mg}{\pi}.

  4. Evaluate numerically: fk=2(0.0500 kg)(9.80 m/s2)π≈0.312 Nf_k = \frac{2(0.0500\text{ kg})(9.80\text{ m/s}^2)}{\pi} \approx 0.312\text{ N}.

Final answer

Threshold fk=0.312 Nf_k = 0.312\text{ N}; Mechanical energy dissipated ΔEmech=−0.392 J\Delta E_{\text{mech}} = -0.392\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always sketch the curve and label the subtended central angle θ\theta before computing arc length or friction work.

  • Double-check that arc length s=Rθs = R\theta matches only the portion of the circle actually traversed.

OverviewACEpath Teacher's Diagnosis

03 The student equates the mechanical energy loss to the friction force alone without multiplying by the distance traveled.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    s=(π2)R=0.5⋅π⋅0.800=1.257 ms = \left(\frac{\pi}{2}\right) R = 0.5 \cdot \pi \cdot 0.800 = 1.257\text{ m}

  2. Step 2

    m⋅g⋅R−fk⋅s=0  ⟹  fk=m⋅g⋅Rs=0.0500⋅9.80⋅0.8001.257=0.312 Nm \cdot g \cdot R - f_k \cdot s = 0 \implies f_k = \frac{m \cdot g \cdot R}{s} = \frac{0.0500 \cdot 9.80 \cdot 0.800}{1.257} = 0.312\text{ N}

  3. Step 3

    ΔEloss=fk  ⟹  ΔEloss=0.312 J\Delta E_{\text{loss}} = f_k \implies \Delta E_{\text{loss}} = 0.312\text{ J}

    Correct

    ΔEmech=−fks=−mgR=−(0.0500 kg)(9.80 m/s2)(0.800 m)=−0.392 J\Delta E_{\text{mech}} = -f_k s = -m g R = -(0.0500\text{ kg})(9.80\text{ m/s}^2)(0.800\text{ m}) = -0.392\text{ J}

    You set the energy loss equal to the friction force alone rather than the work done by friction (Wf=−fksW_f = -f_k s). Energy has units of joules (force times distance), while friction is a force in newtons.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the distance traveled along the curved surface of the bowl.

You correctly applied the work-energy theorem to balance gravitational work and friction work to find fkf_k.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Confusing force and energy

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the friction force fkf_k as if it were directly an amount of energy rather than calculating the work done by friction over the path distance (Wf=−fksW_f = -f_k s).

REASONING PATH
Your ACEpath teacher’s suggested approach
Force vs. Work (Dimensional Consistency)
  • Work and energy transfer require multiplying force by displacement: W=F⋅dW = F \cdot d (or ∫F⃗⋅ds⃗\int \vec{F} \cdot d\vec{s}). A force in newtons cannot equal an energy in joules.

  • Check units whenever solving for energy: multiply friction force by distance traveled to obtain work and energy loss.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recall that the change in mechanical energy equals the work done by non-conservative forces: ΔEmech=Wf=−fks\Delta E_{\text{mech}} = W_f = -f_k s.

  2. Substitute the values or use conservation of total work: Wf=−mgR=−(0.0500 kg)(9.80 m/s2)(0.800 m)=−0.392 JW_f = -m g R = -(0.0500\text{ kg})(9.80\text{ m/s}^2)(0.800\text{ m}) = -0.392\text{ J}.

Final answer

Threshold fk=0.312 Nf_k = 0.312\text{ N}; Mechanical energy dissipated ΔEmech=−0.392 J\Delta E_{\text{mech}} = -0.392\text{ J} (or energy loss of 0.392 J0.392\text{ J})

NEXT STEPS
Final Takeaways from Your Teacher
  • Always perform a unit check: force is in N\text{N}, whereas energy and work are in J=N⋅m\text{J} = \text{N}\cdot\text{m}.

  • Remember that mechanical energy lost to friction is the work done by friction, calculated as Eloss=fk⋅sE_{\text{loss}} = f_k \cdot s.

Lock it in

Similar question

01

A block of mass m=0.200 kgm = 0.200\text{ kg} slides down a quarter-circular ramp of radius R=1.50 mR = 1.50\text{ m} from rest at the top. A constant tangential friction force of magnitude fk=0.400 Nf_k = 0.400\text{ N} opposes its motion. Find the speed of the block at the bottom of the ramp. (Take g=9.80 m/s2g = 9.80\text{ m/s}^2)

Answer

v≈4.47 m/sv \approx 4.47\text{ m/s}. Key steps: Arc length is s=πR2=2.356 ms = \frac{\pi R}{2} = 2.356\text{ m}. Work by gravity is Wg=mgR=2.94 JW_g = m g R = 2.94\text{ J}. Work by friction is Wf=−fks=−(0.400)(2.356)=−0.942 JW_f = -f_k s = -(0.400)(2.356) = -0.942\text{ J}. By work-energy: 12mv2=Wg+Wf=1.998 J  ⟹  v=2(1.998)0.200≈4.47 m/s\frac{1}{2}m v^2 = W_g + W_f = 1.998\text{ J} \implies v = \sqrt{\frac{2(1.998)}{0.200}} \approx 4.47\text{ m/s}.

02

A small slider moves along a semi-circular track of radius R=0.500 mR = 0.500\text{ m} oriented in a vertical plane, starting from the left rim and coming to rest at the right rim (covering half a circle). A constant tangential friction force fkf_k acts throughout. If the slider is launched with an initial kinetic energy of Ki=1.20 JK_i = 1.20\text{ J}, determine the required friction force fkf_k.

Answer

fk≈0.764 Nf_k \approx 0.764\text{ N}. Key steps: Initial and final heights are equal, so Wg=0W_g = 0. Total path length is a semicircle: s=πR=0.500π m≈1.571 ms = \pi R = 0.500\pi\text{ m} \approx 1.571\text{ m}. Work-energy theorem gives ΔK=Kf−Ki=−Ki=Wf=−fks  ⟹  fk=KiπR=1.200.500π≈0.764 N\Delta K = K_f - K_i = -K_i = W_f = -f_k s \implies f_k = \frac{K_i}{\pi R} = \frac{1.20}{0.500\pi} \approx 0.764\text{ N}.

03

A bead of mass m=0.100 kgm = 0.100\text{ kg} is released from rest at an angle θ0=60∘\theta_0 = 60^\circ from the bottom of a vertical circular hoop of radius R=1.20 mR = 1.20\text{ m}. As it slides to the bottom, a constant tangential resistance force f=0.150 Nf = 0.150\text{ N} acts on it. Find the mechanical energy dissipated by resistance and the speed of the bead at the lowest point. (Take g=9.80 m/s2g = 9.80\text{ m/s}^2)

Answer

ΔEmech=−0.188 J\Delta E_{\text{mech}} = -0.188\text{ J} and v≈2.83 m/sv \approx 2.83\text{ m/s}. Key steps: Angular sweep is θ=60∘=π3 rad\theta = 60^\circ = \frac{\pi}{3}\text{ rad}. Arc length is s=Rθ=1.20⋅π3=0.40π m≈1.257 ms = R\theta = 1.20 \cdot \frac{\pi}{3} = 0.40\pi\text{ m} \approx 1.257\text{ m}. Dissipated energy ΔEmech=−fs=−0.150⋅1.257≈−0.188 J\Delta E_{\text{mech}} = -f s = -0.150 \cdot 1.257 \approx -0.188\text{ J}. Vertical drop is h=R(1−cos⁡60∘)=0.600 mh = R(1 - \cos 60^\circ) = 0.600\text{ m}. Kinetic energy at bottom K=mgh−fs=(0.100)(9.80)(0.600)−0.188=0.588−0.188=0.400 JK = mgh - fs = (0.100)(9.80)(0.600) - 0.188 = 0.588 - 0.188 = 0.400\text{ J}. Solving gives v=2(0.400)0.100≈2.83 m/sv = \sqrt{\frac{2(0.400)}{0.100}} \approx 2.83\text{ m/s}.

Loading workspace…