Resources

An electric circuit containing an unknown DC power source with electromotive force E\mathcal{E} and non-zero internal resistance rr is connected to a decade resistance box. A voltmeter measures the terminal potential difference Vt=VA−VBV_t = V_A - V_B across the terminals as the circuit current II is systematically adjusted. The experimenter tabulates the collected readings:

Current I (A)I\text{ (A)}Terminal Voltage Vt (V)V_t\text{ (V)}
0.500.5011.2511.25
1.001.0010.5010.50
1.501.509.759.75
2.002.009.009.00
3.003.007.507.50

Applying Kirchhoff's loop rule and terminal voltage conventions (Vt=E−IrV_t = \mathcal{E} - Ir), account for the negative slope convention on a VtV_t versus II plot to extract the internal resistance rr, find the open-circuit emf E\mathcal{E}, and determine the short-circuit current IscI_{\text{sc}} when the load resistance drops to zero.

Answer and steps

Final answer

E=12.0 V\mathcal{E} = 12.0\text{ V}; r=1.50 Ωr = 1.50\ \Omega; Isc=8.00 AI_{\text{sc}} = 8.00\text{ A}

Steps

01

Relate the Terminal Voltage to the Linear Graph Model

For a real DC voltage source with electromotive force E\mathcal{E} and internal resistance rr, the terminal potential difference VtV_t across its terminals when supplying a current II is given by:

Vt=E−IrV_t = \mathcal{E} - Ir

Rearranging this into standard slope-intercept form (y=mx+cy = mx + c), where the vertical axis is VtV_t and the horizontal axis is II:

Vt=(−r)I+EV_t = (-r)I + \mathcal{E}

From this linear relation:

  • Slope (mm): m=−rm = -r, which explains the negative slope convention—as current draw increases, the internal potential drop across the internal resistance (IrIr) increases, reducing the terminal voltage.
  • Vertical Intercept (cc): At zero current (I=0 AI = 0\text{ A}), open-circuit condition holds, so Vt=EV_t = \mathcal{E}.
  • Horizontal Intercept (IscI_{\text{sc}}): When the external load resistance drops to zero, the terminals are short-circuited (Vt=0 VV_t = 0\text{ V}), giving 0=E−Iscr0 = \mathcal{E} - I_{\text{sc}}r, or Isc=ErI_{\text{sc}} = \frac{\mathcal{E}}{r}.

02

Determine the Internal Resistance (rr)

Pick any two representative data points from the table, for instance (I1,Vt1)=(1.00 A,10.50 V)(I_1, V_{t1}) = (1.00\text{ A}, 10.50\text{ V}) and (I2,Vt2)=(2.00 A,9.00 V)(I_2, V_{t2}) = (2.00\text{ A}, 9.00\text{ V}):

Slope m=ΔVtΔI=9.00 V−10.50 V2.00 A−1.00 A=−1.50 V1.00 A=−1.50 V/A\text{Slope } m = \frac{\Delta V_t}{\Delta I} = \frac{9.00\text{ V} - 10.50\text{ V}}{2.00\text{ A} - 1.00\text{ A}} = \frac{-1.50\text{ V}}{1.00\text{ A}} = -1.50\text{ V/A}

Because the slope equals −r-r:

−r=−1.50 Ω  ⟹  r=1.50 Ω-r = -1.50\ \Omega \implies r = 1.50\ \Omega

(Checking with another interval, such as between 0.50 A0.50\text{ A} and 3.00 A3.00\text{ A}: 7.50−11.253.00−0.50=−3.752.50=−1.50 Ω\frac{7.50 - 11.25}{3.00 - 0.50} = \frac{-3.75}{2.50} = -1.50\ \Omega, confirming the relationship is strictly linear.)


03

Determine the Open-Circuit EMF (E\mathcal{E})

Substitute the calculated value of rr and any data point, such as (I,Vt)=(1.00 A,10.50 V)(I, V_t) = (1.00\text{ A}, 10.50\text{ V}), into the terminal voltage equation:

E=Vt+Ir\mathcal{E} = V_t + Ir

E=10.50 V+(1.00 A)(1.50 Ω)=10.50 V+1.50 V=12.0 V\mathcal{E} = 10.50\text{ V} + (1.00\text{ A})(1.50\ \Omega) = 10.50\text{ V} + 1.50\text{ V} = 12.0\text{ V}


04

Determine the Short-Circuit Current (IscI_{\text{sc}})

Under a short-circuit condition, the load resistance is zero, so the entire electromotive force drops across the internal resistance alone (Vt=0 VV_t = 0\text{ V}):

Isc=Er=12.0 V1.50 Ω=8.00 AI_{\text{sc}} = \frac{\mathcal{E}}{r} = \frac{12.0\text{ V}}{1.50\ \Omega} = 8.00\text{ A}

A common pitfall is to confuse internal resistance rr with a negative value because of the downward slope; resistance is an inherently positive physical quantity (r=−m>0r = -m > 0).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student ignores the negative sign relating slope to internal resistance and computes a negative resistance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    slope=ΔVtΔI=10.50−11.251.00−0.50=−1.50 V/A\text{slope} = \frac{\Delta V_t}{\Delta I} = \frac{10.50 - 11.25}{1.00 - 0.50} = -1.50\text{ V/A}

  2. Step 2

    r=slope=−1.50 Ωr = \text{slope} = -1.50\ \Omega

    Correct

    r=−slope=−(−1.50 V/A)=1.50 Ωr = -\text{slope} = -(-1.50\text{ V/A}) = 1.50\ \Omega

    Comparing Vt=E−IrV_t = \mathcal{E} - Ir to the linear form y=mx+cy = mx + c, the slope is m=−rm = -r. Therefore, the internal resistance is r=−m=1.50 Ωr = -m = 1.50\ \Omega, which must be a positive quantity.

  3. Step 3

    E=Vt−Ir=11.25−(0.50)(−1.50)=12.0 VE = V_t - Ir = 11.25 - (0.50)(-1.50) = 12.0\text{ V}

    Correct

    E=Vt+Ir=11.25 V+(0.50 A)(1.50 Ω)=12.0 V\mathcal{E} = V_t + Ir = 11.25\text{ V} + (0.50\text{ A})(1.50\ \Omega) = 12.0\text{ V}

    From Vt=E−IrV_t = \mathcal{E} - Ir, isolating electromotive force gives E=Vt+Ir\mathcal{E} = V_t + Ir. You wrote E=Vt−IrE = V_t - Ir, and substituting your negative rr accidentally resulted in the correct numerical value.

  4. Step 4

    Isc=Er=12.0(−1.50)=−8.00 AI_{\text{sc}} = \frac{E}{r} = \frac{12.0}{(-1.50)} = -8.00\text{ A}

    Correct

    Isc=Er=12.0 V1.50 Ω=8.00 AI_{\text{sc}} = \frac{\mathcal{E}}{r} = \frac{12.0\text{ V}}{1.50\ \Omega} = 8.00\text{ A}

    Your formula for short-circuit current is conceptually correct, but carrying forward the negative internal resistance resulted in an unphysical negative current.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the numerical rate of change ΔVtΔI=−1.50 V/A\frac{\Delta V_t}{\Delta I} = -1.50\text{ V/A} using coordinates from the table.

You recognized that short-circuit current is given by dividing electromotive force by internal resistance.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign error in slope-parameter mapping

You equated rr directly to the slope mm rather than r=−mr = -m.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You overlooked the minus sign in the terminal voltage relation Vt=E−Ir=(−r)I+EV_t = \mathcal{E} - Ir = (-r)I + \mathcal{E}. Because the slope represents −r-r, a downward-sloping linear plot corresponds to an intrinsically positive internal resistance.

REASONING PATH
Your ACEpath teacher’s suggested approach
Mapping Linear Constants to Physical Quantities
  • In Vt=(−r)I+EV_t = (-r)I + \mathcal{E}, the slope is m=−rm = -r and the vertical intercept is c=Ec = \mathcal{E}.

  • Always rewrite the physical law in explicit slope-intercept form (y=mx+cy = mx + c) before matching variables, ensuring any negative signs are assigned to the slope.

Physical Reality of Passive Resistance
  • Internal resistance rr of a passive power cell must satisfy r>0r > 0.

  • Check the sign of resistance immediately upon calculation; if you obtain a negative value for a passive element, re-examine your slope equation.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the measured slope equal to the model's slope: m=−r=−1.50 V/A  ⟹  r=1.50 Ωm = -r = -1.50\text{ V/A} \implies r = 1.50\ \Omega.

  2. Rearrange the terminal voltage equation to solve for open-circuit electromotive force: E=Vt+Ir=11.25 V+(0.50 A)(1.50 Ω)=12.0 V\mathcal{E} = V_t + Ir = 11.25\text{ V} + (0.50\text{ A})(1.50\ \Omega) = 12.0\text{ V}.

  3. Evaluate the short-circuit current using positive values: Isc=Er=12.0 V1.50 Ω=8.00 AI_{\text{sc}} = \frac{\mathcal{E}}{r} = \frac{12.0\text{ V}}{1.50\ \Omega} = 8.00\text{ A}.

Final answer

E=12.0 V\mathcal{E} = 12.0\text{ V}, r=1.50 Ωr = 1.50\ \Omega, Isc=8.00 AI_{\text{sc}} = 8.00\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice matching the slope-intercept form y=mx+cy = mx + c directly against equations with negative terms such as Vt=E−IrV_t = \mathcal{E} - Ir.

  • Perform a sanity check on calculated physical quantities like resistance and current draw to ensure they have physically meaningful positive signs.

OverviewACEpath Teacher's Diagnosis

02 The student treats the terminal voltage at the lowest measured current as the open-circuit emf instead of extrapolating to zero current.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    slope=9.00−10.502.00−1.00=−1.50 V/A  ⟹  r=−slope=1.50 Ω\text{slope} = \frac{9.00 - 10.50}{2.00 - 1.00} = -1.50\text{ V/A} \implies r = -\text{slope} = 1.50\ \Omega

  2. Step 2

    E=11.25 VE = 11.25\text{ V}

    Correct

    E=Vt+Ir=11.25 V+(0.50 A)(1.50 Ω)=12.0 V\mathcal{E} = V_t + Ir = 11.25\text{ V} + (0.50\text{ A})(1.50\ \Omega) = 12.0\text{ V}

    You read the terminal voltage at the first tabulated point (I=0.50 AI = 0.50\text{ A}) as the electromotive force. Open-circuit emf occurs when no current flows (I=0 AI = 0\text{ A}), so you must extrapolate back to I=0 AI = 0\text{ A} using E=Vt+Ir\mathcal{E} = V_t + Ir.

  3. Step 3

    Isc=Er=11.251.50=7.50 AI_{\text{sc}} = \frac{E}{r} = \frac{11.25}{1.50} = 7.50\text{ A}

    Correct

    Isc=Er=12.0 V1.50 Ω=8.00 AI_{\text{sc}} = \frac{\mathcal{E}}{r} = \frac{12.0\text{ V}}{1.50\ \Omega} = 8.00\text{ A}

    Your formula Isc=ErI_{\text{sc}} = \frac{\mathcal{E}}{r} is correct, but your numerical result is affected by substituting the incorrect value of E\mathcal{E}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that the slope of the Vt−IV_t-I graph equals −r-r.

You correctly applied the short-circuit relationship Isc=ErI_{\text{sc}} = \frac{\mathcal{E}}{r}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Confusing lowest measured data point with zero-current intercept

You assumed the first row in the data table was the vertical intercept.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the minimum experimental current reading (I=0.50 AI = 0.50\text{ A}) as an open circuit (I=0 AI = 0\text{ A}), overlooking the internal potential drop IrIr that is already present at that non-zero current.

REASONING PATH
Your ACEpath teacher’s suggested approach
Definition of Open-Circuit EMF
  • The electromotive force E\mathcal{E} equals the terminal voltage VtV_t only when I=0 AI = 0\text{ A}.

  • Check whether the first table row has I=0 AI = 0\text{ A}. If I>0 AI > 0\text{ A}, compute E=Vt+Ir\mathcal{E} = V_t + Ir using the calculated slope/resistance.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use any data pair (I,Vt)(I, V_t), such as (0.50 A,11.25 V)(0.50\text{ A}, 11.25\text{ V}), and your calculated r=1.50 Ωr = 1.50\ \Omega.

  2. Solve for the open-circuit emf: E=Vt+Ir=11.25 V+(0.50 A)(1.50 Ω)=12.0 V\mathcal{E} = V_t + Ir = 11.25\text{ V} + (0.50\text{ A})(1.50\ \Omega) = 12.0\text{ V}.

  3. Recalculate the short-circuit current: Isc=Er=12.0 V1.50 Ω=8.00 AI_{\text{sc}} = \frac{\mathcal{E}}{r} = \frac{12.0\text{ V}}{1.50\ \Omega} = 8.00\text{ A}.

Final answer

E=12.0 V\mathcal{E} = 12.0\text{ V}; r=1.50 Ωr = 1.50\ \Omega; Isc=8.00 AI_{\text{sc}} = 8.00\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always inspect table headers and coordinate axes to confirm whether the first data point starts at zero or at an offset.

  • Use the linear equation Vt=E−IrV_t = \mathcal{E} - Ir to solve for the intercept algebraically whenever I=0I = 0 is not explicitly measured.

OverviewACEpath Teacher's Diagnosis

03 The student inverts the slope formula as ΔI / ΔVt when extracting internal resistance from the graph.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    r=−(ΔIΔVt)=−(1.00−0.50)10.50−11.25=0.67 Ωr = -\left(\frac{\Delta I}{\Delta V_t}\right) = \frac{-(1.00 - 0.50)}{10.50 - 11.25} = 0.67\ \Omega

    Correct

    r=−(ΔVtΔI)=−(10.50 V−11.25 V1.00 A−0.50 A)=1.50 Ωr = -\left(\frac{\Delta V_t}{\Delta I}\right) = -\left(\frac{10.50\text{ V} - 11.25\text{ V}}{1.00\text{ A} - 0.50\text{ A}}\right) = 1.50\ \Omega

    On a plot of VtV_t versus II, terminal voltage VtV_t is on the vertical axis (yy) and current II is on the horizontal axis (xx). The slope is m=ΔyΔx=ΔVtΔI=−rm = \frac{\Delta y}{\Delta x} = \frac{\Delta V_t}{\Delta I} = -r. You inverted the fraction to ΔIΔVt\frac{\Delta I}{\Delta V_t}, which computes 1m\frac{1}{m} rather than mm.

  2. Step 2

    E=Vt+Ir=11.25+(0.50)(0.67)=11.59 VE = V_t + Ir = 11.25 + (0.50)(0.67) = 11.59\text{ V}

    Correct

    E=Vt+Ir=11.25 V+(0.50 A)(1.50 Ω)=12.0 V\mathcal{E} = V_t + Ir = 11.25\text{ V} + (0.50\text{ A})(1.50\ \Omega) = 12.0\text{ V}

    Your formula E=Vt+Ir\mathcal{E} = V_t + Ir and substitution of the data point (0.50 A,11.25 V)(0.50\text{ A}, 11.25\text{ V}) were completely sound, but the result was thrown off by the incorrect value of rr from Step 1.

  3. Step 3

    Isc=Er=11.590.67=17.3 AI_{\text{sc}} = \frac{E}{r} = \frac{11.59}{0.67} = 17.3\text{ A}

    Correct

    Isc=Er=12.0 V1.50 Ω=8.00 AI_{\text{sc}} = \frac{\mathcal{E}}{r} = \frac{12.0\text{ V}}{1.50\ \Omega} = 8.00\text{ A}

    Your conceptual formula for short-circuit current Isc=ErI_{\text{sc}} = \frac{\mathcal{E}}{r} is correct, but your final numerical value was affected by your previous values for E\mathcal{E} and rr.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that terminal voltage follows the linear model Vt=E−IrV_t = \mathcal{E} - Ir.

You correctly applied E=Vt+Ir\mathcal{E} = V_t + Ir to solve for the open-circuit electromotive force.

You correctly related the short-circuit condition to the ratio Er\frac{\mathcal{E}}{r}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted slope ratio (run over rise)

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the dependent and independent variables when applying the slope formula m=ΔyΔxm = \frac{\Delta y}{\Delta x}, calculating ΔIΔVt\frac{\Delta I}{\Delta V_t} instead of ΔVtΔI\frac{\Delta V_t}{\Delta I} for a VtV_t vs. II graph.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Axis Quantities
  • In a 'yy versus xx' graph, the first named variable is on the vertical axis and the second is on the horizontal axis.

  • Check that ΔVt\Delta V_t is placed in the numerator as the rise (vertical change) and ΔI\Delta I in the denominator as the run (horizontal change).

Check Dimensions and Units
  • Resistance has units of volts per ampere (V/A=Ω\text{V}/\text{A} = \Omega), not amperes per volt.

  • Always verify the units of your slope: VA=Ω\frac{\text{V}}{\text{A}} = \Omega. If you find AV=Ω−1\frac{\text{A}}{\text{V}} = \Omega^{-1}, you have inverted the ratio.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the slope correctly using m=ΔVtΔI=10.50 V−11.25 V1.00 A−0.50 A=−0.75 V0.50 A=−1.50 Ωm = \frac{\Delta V_t}{\Delta I} = \frac{10.50\text{ V} - 11.25\text{ V}}{1.00\text{ A} - 0.50\text{ A}} = \frac{-0.75\text{ V}}{0.50\text{ A}} = -1.50\ \Omega.

  2. Find the internal resistance: r=−m=1.50 Ωr = -m = 1.50\ \Omega.

  3. Substitute r=1.50 Ωr = 1.50\ \Omega into E=Vt+Ir\mathcal{E} = V_t + Ir: E=11.25 V+(0.50 A)(1.50 Ω)=12.0 V\mathcal{E} = 11.25\text{ V} + (0.50\text{ A})(1.50\ \Omega) = 12.0\text{ V}.

  4. Calculate the short-circuit current: Isc=Er=12.0 V1.50 Ω=8.00 AI_{\text{sc}} = \frac{\mathcal{E}}{r} = \frac{12.0\text{ V}}{1.50\ \Omega} = 8.00\text{ A}.

Final answer

E=12.0 V\mathcal{E} = 12.0\text{ V}; r=1.50 Ωr = 1.50\ \Omega; Isc=8.00 AI_{\text{sc}} = 8.00\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Before calculating slopes, explicitly write out Slope=Δ(vertical axis)Δ(horizontal axis)\text{Slope} = \frac{\Delta (\text{vertical axis})}{\Delta (\text{horizontal axis})}.

  • Perform a quick dimensional check on every extracted experimental parameter to catch inverted fractions immediately.

Lock it in

Similar question

01

A battery's terminal voltage is measured as 8.40 V8.40\text{ V} at a current of 0.60 A0.60\text{ A} and 7.20 V7.20\text{ V} at a current of 1.80 A1.80\text{ A}. Determine the internal resistance rr and the electromotive force E\mathcal{E}.

Answer

r=1.00 Ωr = 1.00\ \Omega, E=9.00 V\mathcal{E} = 9.00\text{ V}. Calculate slope: m=7.20−8.401.80−0.60=−1.00 V/Am = \frac{7.20 - 8.40}{1.80 - 0.60} = -1.00\text{ V/A}. Since m=−rm = -r, r=1.00 Ωr = 1.00\ \Omega. Then E=Vt+Ir=8.40+(0.60)(1.00)=9.00 V\mathcal{E} = V_t + Ir = 8.40 + (0.60)(1.00) = 9.00\text{ V}.

02

An experimenter plots VtV_t on the vertical axis against II on the horizontal axis for a DC power supply. The linear fit yields Vt=−0.40I+24.0V_t = -0.40 I + 24.0. Find the open-circuit voltage, internal resistance, and the current delivered under a dead short (Rload=0R_{\text{load}} = 0).

Answer

E=24.0 V\mathcal{E} = 24.0\text{ V}, r=0.40 Ωr = 0.40\ \Omega, Isc=60.0 AI_{\text{sc}} = 60.0\text{ A}. Comparing with Vt=(−r)I+EV_t = (-r)I + \mathcal{E}, the vertical intercept is E=24.0 V\mathcal{E} = 24.0\text{ V} and r=−(−0.40 Ω)=0.40 Ωr = -(-0.40\ \Omega) = 0.40\ \Omega. Under a dead short, Isc=Er=24.0 V0.40 Ω=60.0 AI_{\text{sc}} = \frac{\mathcal{E}}{r} = \frac{24.0\text{ V}}{0.40\ \Omega} = 60.0\text{ A}.

03

A solar module shows a linear operating segment where terminal voltage drops from 36.0 V36.0\text{ V} at 2.00 A2.00\text{ A} to 30.0 V30.0\text{ V} at 5.00 A5.00\text{ A}. If an external variable resistor is adjusted until the terminal voltage drops to half of the open-circuit voltage E\mathcal{E}, determine the circuit current and the external load resistance at this point.

Answer

I=10.0 AI = 10.0\text{ A}, Rload=2.00 ΩR_{\text{load}} = 2.00\ \Omega. Slope m=30.0−36.05.00−2.00=−2.00 V/A  ⟹  r=2.00 Ωm = \frac{30.0 - 36.0}{5.00 - 2.00} = -2.00\text{ V/A} \implies r = 2.00\ \Omega. Then E=36.0+(2.00)(2.00)=40.0 V\mathcal{E} = 36.0 + (2.00)(2.00) = 40.0\text{ V}. At half emf, Vt=20.0 VV_t = 20.0\text{ V}. Current is I=E−Vtr=40.0−20.02.00=10.0 AI = \frac{\mathcal{E} - V_t}{r} = \frac{40.0 - 20.0}{2.00} = 10.0\text{ A}. External resistance is Rload=VtI=20.0 V10.0 A=2.00 ΩR_{\text{load}} = \frac{V_t}{I} = \frac{20.0\text{ V}}{10.0\text{ A}} = 2.00\ \Omega (which also matches Rload=rR_{\text{load}} = r for maximum power transfer).

Loading workspace…