Resources

A municipal fire hose system delivers water through a nozzle of exit diameter dexit=2.50 cmd_{\text{exit}} = 2.50\text{ cm} at an exit velocity of vexit=28.0 m/sv_{\text{exit}} = 28.0\text{ m/s}. Upstream, water is fed through a supply hose at a speed of vsupply=1.75 m/sv_{\text{supply}} = 1.75\text{ m/s}. Working backwards from this operational state, determine the internal diameter dsupplyd_{\text{supply}} of the main supply hose and the total volume of water discharged in 15.0 minutes15.0\text{ minutes} of operation.

Answer and steps

Final answer

dsupply=10.0 cmd_{\text{supply}} = 10.0\text{ cm}, V=12.4 m3V = 12.4\text{ m}^3 (or 1.24×104 L1.24 \times 10^4\text{ L})

Steps

01

Apply the Equation of Continuity

For an incompressible fluid like water flowing continuously without leaks, the volumetric flow rate QQ is constant along the pipe:

Q=Asupplyvsupply=AexitvexitQ = A_{\text{supply}} v_{\text{supply}} = A_{\text{exit}} v_{\text{exit}}

The cross-sectional area of a circular tube with diameter dd is given by A=πd24A = \frac{\pi d^2}{4}. Substituting this into the continuity equation gives:

πdsupply24vsupply=πdexit24vexit\frac{\pi d_{\text{supply}}^2}{4} v_{\text{supply}} = \frac{\pi d_{\text{exit}}^2}{4} v_{\text{exit}}

Cancel the common factor of π4\frac{\pi}{4} and solve for dsupplyd_{\text{supply}}:

dsupply2=dexit2⋅vexitvsupplyd_{\text{supply}}^2 = d_{\text{exit}}^2 \cdot \frac{v_{\text{exit}}}{v_{\text{supply}}}

dsupply=dexitvexitvsupplyd_{\text{supply}} = d_{\text{exit}} \sqrt{\frac{v_{\text{exit}}}{v_{\text{supply}}}}

Substitute the given values (dexit=2.50 cmd_{\text{exit}} = 2.50\text{ cm}, vexit=28.0 m/sv_{\text{exit}} = 28.0\text{ m/s}, and vsupply=1.75 m/sv_{\text{supply}} = 1.75\text{ m/s}):

vexitvsupply=28.01.75=16.0\frac{v_{\text{exit}}}{v_{\text{supply}}} = \frac{28.0}{1.75} = 16.0

dsupply=2.50 cm×16.0=2.50 cm×4.00=10.0 cmd_{\text{supply}} = 2.50\text{ cm} \times \sqrt{16.0} = 2.50\text{ cm} \times 4.00 = 10.0\text{ cm}


02

Calculate the Volumetric Flow Rate

The volume flow rate QQ can be calculated at the nozzle exit using SI units (dexit=0.0250 md_{\text{exit}} = 0.0250\text{ m}):

Q=Aexitvexit=π(0.0250 m)24⋅(28.0 m/s)Q = A_{\text{exit}} v_{\text{exit}} = \frac{\pi (0.0250\text{ m})^2}{4} \cdot (28.0\text{ m/s})

Q≈4.9087×10−4 m2×28.0 m/s≈0.01374 m3/sQ \approx 4.9087 \times 10^{-4}\text{ m}^2 \times 28.0\text{ m/s} \approx 0.01374\text{ m}^3/\text{s}


03

Calculate Total Volume Discharged

Convert the operating time into seconds:

t=15.0 minutes×60 s/min=900 st = 15.0\text{ minutes} \times 60\text{ s/min} = 900\text{ s}

Multiply the flow rate by the duration to find the total discharged volume VV:

V=Q⋅t=(0.01374 m3/s)×900 s≈12.4 m3V = Q \cdot t = (0.01374\text{ m}^3/\text{s}) \times 900\text{ s} \approx 12.4\text{ m}^3

Expressed in liters (1 m3=1000 L1\text{ m}^3 = 1000\text{ L}):

V=12.4×103 L=1.24×104 LV = 12.4 \times 10^3\text{ L} = 1.24 \times 10^4\text{ L}

Common Pitfall: Remember that cross-sectional area depends on the square of the diameter (A∝d2A \propto d^2). Therefore, when speed increases by a factor of 1616, the diameter decreases by a factor of 16=4\sqrt{16} = 4, not 1616.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that cross-sectional area is proportional to the square of diameter and equates the product of diameter and velocity instead of area and velocity.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    dsupply⋅vsupply=dexit⋅vexit  ⟹  dsupply⋅1.75=2.50⋅28.0  ⟹  dsupply=70.01.75=40.0 cmd_{\text{supply}} \cdot v_{\text{supply}} = d_{\text{exit}} \cdot v_{\text{exit}} \implies d_{\text{supply}} \cdot 1.75 = 2.50 \cdot 28.0 \implies d_{\text{supply}} = \frac{70.0}{1.75} = 40.0\text{ cm}

    Correct

    Asupplyvsupply=Aexitvexit  ⟹  dsupply2vsupply=dexit2vexit  ⟹  dsupply=dexitvexitvsupply=2.50 cm×28.01.75=10.0 cmA_{\text{supply}} v_{\text{supply}} = A_{\text{exit}} v_{\text{exit}} \implies d_{\text{supply}}^2 v_{\text{supply}} = d_{\text{exit}}^2 v_{\text{exit}} \implies d_{\text{supply}} = d_{\text{exit}}\sqrt{\frac{v_{\text{exit}}}{v_{\text{supply}}}} = 2.50\text{ cm} \times \sqrt{\frac{28.0}{1.75}} = 10.0\text{ cm}

    The continuity equation equates volumetric flow rates, A1v1=A2v2A_1 v_1 = A_2 v_2. Because cross-sectional area depends on the square of the diameter (A=πd24A = \frac{\pi d^2}{4}), the diameters must be squared: dsupply2vsupply=dexit2vexitd_{\text{supply}}^2 v_{\text{supply}} = d_{\text{exit}}^2 v_{\text{exit}}.

  2. Step 2

    Q=(π4)⋅(0.0250)2⋅28.0=0.01374 m3/sQ = \left(\frac{\pi}{4}\right) \cdot (0.0250)^2 \cdot 28.0 = 0.01374\text{ m}^3/\text{s}

  3. Step 3

    t=15.0⋅60=900 s  ⟹  V=Q⋅t=0.01374⋅900=12.4 m3t = 15.0 \cdot 60 = 900\text{ s} \implies V = Q \cdot t = 0.01374 \cdot 900 = 12.4\text{ m}^3

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the cross-sectional area formula A=πd24A = \frac{\pi d^2}{4} when computing the volume flow rate QQ.

You converted minutes to seconds accurately and evaluated the total volume discharged correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Linear diameter continuity error

You equated d1v1=d2v2d_1 v_1 = d_2 v_2 instead of A1v1=A2v2A_1 v_1 = A_2 v_2, missing the square on the diameters.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the linear dimension (diameter dd) with the two-dimensional cross-sectional area (A∝d2A \propto d^2) when applying the continuity equation Q=Av=constantQ = Av = \text{constant}.

REASONING PATH
Your ACEpath teacher’s suggested approach
State the continuity equation in terms of area
  • Q=A1v1=A2v2Q = A_1 v_1 = A_2 v_2 for an incompressible fluid.

  • Always write out area times velocity first before replacing area with diameter.

Substitute circular geometry
  • For a circular duct, A=πd24A = \frac{\pi d^2}{4}, so d12v1=d22v2d_1^2 v_1 = d_2^2 v_2.

  • Remember that velocity is inversely proportional to d2d^2, meaning d∝1vd \propto \frac{1}{\sqrt{v}}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the continuity equation using area: Asupplyvsupply=AexitvexitA_{\text{supply}} v_{\text{supply}} = A_{\text{exit}} v_{\text{exit}}.

  2. Express areas in terms of diameters: π4dsupply2vsupply=π4dexit2vexit\frac{\pi}{4} d_{\text{supply}}^2 v_{\text{supply}} = \frac{\pi}{4} d_{\text{exit}}^2 v_{\text{exit}}.

  3. Cancel π4\frac{\pi}{4} and isolate dsupplyd_{\text{supply}}: dsupply=dexitvexitvsupplyd_{\text{supply}} = d_{\text{exit}} \sqrt{\frac{v_{\text{exit}}}{v_{\text{supply}}}}.

  4. Substitute numerical values: dsupply=2.50 cm×28.01.75=2.50 cm×16.0=2.50 cm×4.00=10.0 cmd_{\text{supply}} = 2.50\text{ cm} \times \sqrt{\frac{28.0}{1.75}} = 2.50\text{ cm} \times \sqrt{16.0} = 2.50\text{ cm} \times 4.00 = 10.0\text{ cm}.

Final answer

dsupply=10.0 cmd_{\text{supply}} = 10.0\text{ cm}, V=12.4 m3V = 12.4\text{ m}^3

NEXT STEPS
Final Takeaways from Your Teacher
  • Review circular pipe continuity problems and check that every diameter term enters as d2d^2.

  • Practice checking dimensions: velocity has units of m/s\text{m/s}, so multiplying by diameter gives m2/s\text{m}^2/\text{s}, which is not a volumetric flow rate (m3/s\text{m}^3/\text{s}).

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert the elapsed time from minutes to seconds when multiplying by the volumetric flow rate in cubic meters per second.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Asupply⋅vsupply=Aexit⋅vexit  ⟹  dsupply=dexit⋅vexitvsupply=2.50⋅28.01.75=2.50⋅4.00=10.0 cmA_{\text{supply}} \cdot v_{\text{supply}} = A_{\text{exit}} \cdot v_{\text{exit}} \implies d_{\text{supply}} = d_{\text{exit}} \cdot \sqrt{\frac{v_{\text{exit}}}{v_{\text{supply}}}} = 2.50 \cdot \sqrt{\frac{28.0}{1.75}} = 2.50 \cdot 4.00 = 10.0\text{ cm}

  2. Step 2

    Q=π4⋅(0.0250)2⋅28.0=0.01374 m3/sQ = \frac{\pi}{4} \cdot (0.0250)^2 \cdot 28.0 = 0.01374\text{ m}^3/\text{s}

  3. Step 3

    V=Q⋅t=0.01374⋅15.0=0.206 m3V = Q \cdot t = 0.01374 \cdot 15.0 = 0.206\text{ m}^3

    Correct

    V=Q⋅t=(0.01374 m3/s)×(15.0×60 s)=0.01374×900≈12.4 m3V = Q \cdot t = (0.01374\text{ m}^3/\text{s}) \times (15.0 \times 60\text{ s}) = 0.01374 \times 900 \approx 12.4\text{ m}^3

    You multiplied a flow rate measured in cubic meters per second by a time measured in minutes without converting the time to seconds (15.0 min=900 s15.0\text{ min} = 900\text{ s}).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that the continuity equation applies to the incompressible water flow.

You accurately solved for the supply diameter using the square root of the velocity ratio.

You calculated the nozzle area and volume flow rate with correct SI unit conversions for centimeters to meters.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Time Unit Conversion Error

You substituted t=15.0t = 15.0 directly instead of converting 15.0 minutes15.0\text{ minutes} into 900 seconds900\text{ seconds}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking unit consistency across derived rates and time intervals when transitioning from finding QQ in m3/s\text{m}^3/\text{s} to computing accumulated volume.

REASONING PATH
Your ACEpath teacher’s suggested approach
Match Rate Units to Time Units
  • If flow rate QQ is expressed in m3/s\text{m}^3/\text{s}, elapsed time tt must be expressed in seconds so that the time units cancel: (m3/s)×s=m3(\text{m}^3/\text{s}) \times \text{s} = \text{m}^3.

  • Always write down units explicitly during substitution to verify that the time units cancel.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert elapsed time to seconds: t=15.0 min×60 s/min=900 st = 15.0\text{ min} \times 60\text{ s/min} = 900\text{ s}.

  2. Compute total volume: V=Q⋅t=(0.01374 m3/s)×900 s≈12.4 m3V = Q \cdot t = (0.01374\text{ m}^3/\text{s}) \times 900\text{ s} \approx 12.4\text{ m}^3.

Final answer

dsupply=10.0 cmd_{\text{supply}} = 10.0\text{ cm}, V=12.4 m3V = 12.4\text{ m}^3 (or 1.24×104 L1.24 \times 10^4\text{ L})

NEXT STEPS
Final Takeaways from Your Teacher
  • Include explicit physical units in each multiplication step to confirm unit cancellation.

  • Practice converting non-SI time intervals (minutes, hours) into seconds at the start of multi-step kinematic and fluid flow problems.

OverviewACEpath Teacher's Diagnosis

03 The student treats the diameter directly as the radius when calculating the cross-sectional area for flow rate.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Asupply⋅vsupply=Aexit⋅vexit  ⟹  (dsupplydexit)2=vexitvsupply  ⟹  dsupply=2.50⋅28.01.75=10.0 cmA_{\text{supply}} \cdot v_{\text{supply}} = A_{\text{exit}} \cdot v_{\text{exit}} \implies \left(\frac{d_{\text{supply}}}{d_{\text{exit}}}\right)^2 = \frac{v_{\text{exit}}}{v_{\text{supply}}} \implies d_{\text{supply}} = 2.50 \cdot \sqrt{\frac{28.0}{1.75}} = 10.0\text{ cm}

  2. Step 2

    Aexit=π⋅r2=π⋅(0.0250)2=0.001963 m2A_{\text{exit}} = \pi \cdot r^2 = \pi \cdot (0.0250)^2 = 0.001963\text{ m}^2

    Correct

    Aexit=πdexit24=π(0.0250 m)24≈4.909×10−4 m2A_{\text{exit}} = \frac{\pi d_{\text{exit}}^2}{4} = \frac{\pi (0.0250\text{ m})^2}{4} \approx 4.909 \times 10^{-4}\text{ m}^2

    You substituted the diameter dexit=0.0250 md_{\text{exit}} = 0.0250\text{ m} directly into rr in the area formula πr2\pi r^2. Since r=d2=0.0125 mr = \frac{d}{2} = 0.0125\text{ m}, the area formula should be πd24\frac{\pi d^2}{4} or π(0.0125 m)2\pi (0.0125\text{ m})^2.

  3. Step 3

    Q=Aexit⋅vexit=0.001963⋅28.0=0.0550 m3/sQ = A_{\text{exit}} \cdot v_{\text{exit}} = 0.001963 \cdot 28.0 = 0.0550\text{ m}^3/\text{s}

    Correct

    Q=Aexitvexit=(4.909×10−4 m2)(28.0 m/s)≈0.01374 m3/sQ = A_{\text{exit}} v_{\text{exit}} = (4.909 \times 10^{-4}\text{ m}^2)(28.0\text{ m/s}) \approx 0.01374\text{ m}^3/\text{s}

    You correctly applied the flow rate formula Q=AvQ = Av, but the result was affected by the upstream area error.

  4. Step 4

    t=15.0⋅60=900 s  ⟹  V=Q⋅t=0.0550⋅900=49.5 m3t = 15.0 \cdot 60 = 900\text{ s} \implies V = Q \cdot t = 0.0550 \cdot 900 = 49.5\text{ m}^3

    Correct

    t=900 s  ⟹  V=Q⋅t=(0.01374 m3/s)(900 s)≈12.4 m3t = 900\text{ s} \implies V = Q \cdot t = (0.01374\text{ m}^3/\text{s})(900\text{ s}) \approx 12.4\text{ m}^3

    You converted time to seconds correctly and used V=Q⋅tV = Q \cdot t, but your final volume was 4 times too large due to the earlier area miscalculation.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly stated and rearranged the continuity equation for circular cross-sections.

You correctly determined that the supply hose diameter is 10.0 cm10.0\text{ cm}.

You correctly converted the elapsed time of 15.0 minutes15.0\text{ minutes} into 900 seconds900\text{ seconds}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Radius vs. Diameter Confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the given diameter value (2.50 cm=0.0250 m2.50\text{ cm} = 0.0250\text{ m}) as the radius rr when applying the circular area formula A=πr2A = \pi r^2, omitting the required division by 2 (or factor of 14\frac{1}{4}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Circular Area Form
  • For a circular pipe of diameter dd, the cross-sectional area is A=πd24A = \frac{\pi d^2}{4}, or A=πr2A = \pi r^2 where r=d2r = \frac{d}{2}.

  • Whenever a problem provides a diameter, write down r=d2r = \frac{d}{2} immediately before calculating area, or use A=πd24A = \frac{\pi d^2}{4} directly.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the correct exit area using Aexit=πdexit24=π(0.0250 m)24≈4.909×10−4 m2A_{\text{exit}} = \frac{\pi d_{\text{exit}}^2}{4} = \frac{\pi (0.0250\text{ m})^2}{4} \approx 4.909 \times 10^{-4}\text{ m}^2.

  2. Multiply this area by the exit speed: Q=(4.909×10−4 m2)(28.0 m/s)≈0.01374 m3/sQ = (4.909 \times 10^{-4}\text{ m}^2)(28.0\text{ m/s}) \approx 0.01374\text{ m}^3/\text{s}.

  3. Multiply flow rate by time: V=(0.01374 m3/s)(900 s)≈12.4 m3V = (0.01374\text{ m}^3/\text{s})(900\text{ s}) \approx 12.4\text{ m}^3.

Final answer

dsupply=10.0 cmd_{\text{supply}} = 10.0\text{ cm}, V=12.4 m3V = 12.4\text{ m}^3 (or 1.24×104 L1.24 \times 10^4\text{ L})

NEXT STEPS
Final Takeaways from Your Teacher
  • Always double-check whether a given dimension is labeled as diameter (dd) or radius (rr) before substituting into an area formula.

  • Practice expressing circular area directly in terms of diameter as A=π4d2A = \frac{\pi}{4}d^2 to eliminate radius conversion slips.

Lock it in

Similar question

01

A garden hose with an internal diameter of 2.0 cm2.0\text{ cm} carries water at 1.5 m/s1.5\text{ m/s}. It connects to an adjustable nozzle with an exit diameter of 0.50 cm0.50\text{ cm}. Find the exit speed of the water.

Answer

v2=24 m/sv_2 = 24\text{ m/s}. Using d12v1=d22v2d_1^2 v_1 = d_2^2 v_2, we have v2=v1(d1d2)2=1.5 m/s×(2.00.50)2=1.5×16=24 m/sv_2 = v_1 \left(\frac{d_1}{d_2}\right)^2 = 1.5\text{ m/s} \times \left(\frac{2.0}{0.50}\right)^2 = 1.5 \times 16 = 24\text{ m/s}.

02

Oil flows through a horizontal pipeline that widens from a diameter of 12 cm12\text{ cm} to 24 cm24\text{ cm}. If the flow rate is 0.045 m3/s0.045\text{ m}^3/\text{s}, calculate the flow speed in both sections.

Answer

v1≈3.98 m/sv_1 \approx 3.98\text{ m/s}, v2≈0.995 m/sv_2 \approx 0.995\text{ m/s}. A1=π(0.12 m)24≈0.01131 m2A_1 = \frac{\pi (0.12\text{ m})^2}{4} \approx 0.01131\text{ m}^2, so v1=0.0450.01131≈3.98 m/sv_1 = \frac{0.045}{0.01131} \approx 3.98\text{ m/s}. Since diameter doubles, speed drops by 22=42^2 = 4, yielding v2=3.984≈0.995 m/sv_2 = \frac{3.98}{4} \approx 0.995\text{ m/s}.

03

A syringe has a barrel diameter of 1.20 cm1.20\text{ cm} and a needle diameter of 0.600 mm0.600\text{ mm}. A plunger is pushed at 8.00 mm/s8.00\text{ mm/s}. Find the fluid speed exiting the needle and determine the volume injected in 5.00 s5.00\text{ s}.

Answer

vneedle=3.20 m/sv_{\text{needle}} = 3.20\text{ m/s}, V=4.52 mLV = 4.52\text{ mL} (or 4.52×10−6 m34.52 \times 10^{-6}\text{ m}^3). Diameter ratio is 12.0 mm0.600 mm=20\frac{12.0\text{ mm}}{0.600\text{ mm}} = 20, so speed increases by 202=40020^2 = 400: vneedle=0.00800 m/s×400=3.20 m/sv_{\text{needle}} = 0.00800\text{ m/s} \times 400 = 3.20\text{ m/s}. Flow rate Q=π(0.0120 m)24×(0.00800 m/s)≈9.048×10−7 m3/sQ = \frac{\pi (0.0120\text{ m})^2}{4} \times (0.00800\text{ m/s}) \approx 9.048 \times 10^{-7}\text{ m}^3/\text{s}. Discharged volume V=Q×5.00 s≈4.52×10−6 m3=4.52 mLV = Q \times 5.00\text{ s} \approx 4.52 \times 10^{-6}\text{ m}^3 = 4.52\text{ mL}.

Loading workspace…