Resources

A warehouse loading ramp has a length of L=6.00 mL = 6.00\text{ m} and rises to a vertical loading dock of height h=1.80 mh = 1.80\text{ m}. A worker pushes a crate of mass m=65.0 kgm = 65.0\text{ kg} up the incline at a constant speed by applying a steady force FappliedF_{\text{applied}} directed parallel to the incline. If the maximum permissible mechanical efficiency of the inclined plane must not fall below ηmin⁡=55.0%\eta_{\min} = 55.0\%, determine the critical threshold value for the coefficient of kinetic friction μk\mu_k between the crate and the ramp surface. (Take g=9.80 m/s2g = 9.80\text{ m/s}^2.)

Answer and steps

Final answer

μk=0.260\mu_k = 0.260

Steps

01

Incline Geometry

The ramp forms a right-angled triangle with length (hypotenuse) L=6.00 mL = 6.00\text{ m} and height h=1.80 mh = 1.80\text{ m}. Let θ\theta be the angle of inclination with the horizontal:

sin⁡θ=hL=1.80 m6.00 m=0.300\sin\theta = \frac{h}{L} = \frac{1.80\text{ m}}{6.00\text{ m}} = 0.300

Using the Pythagorean identity:

cos⁡θ=1−sin⁡2θ=1−0.3002=0.910≈0.9539\cos\theta = \sqrt{1 - \sin^2\theta} = \sqrt{1 - 0.300^2} = \sqrt{0.910} \approx 0.9539

tan⁡θ=sin⁡θcos⁡θ=0.3000.9539≈0.3145\tan\theta = \frac{\sin\theta}{\cos\theta} = \frac{0.300}{0.9539} \approx 0.3145


02

Work Output and Work Input

  • Useful Work Output (WoutW_{\text{out}}):
    The useful task accomplished is raising the crate of mass mm through vertical height hh: Wout=mghW_{\text{out}} = mgh
  • Applied Force (FappliedF_{\text{applied}}):
    Because the crate is pushed up the ramp at a constant speed, the net force along the incline is zero. The applied force parallel to the incline must balance both the parallel component of gravity and kinetic friction: Fapplied=mgsin⁡θ+fkF_{\text{applied}} = mg\sin\theta + f_k

    The normal force perpendicular to the ramp surface is N=mgcos⁡θN = mg\cos\theta, so the kinetic friction force is: fk=μkN=μkmgcos⁡θf_k = \mu_k N = \mu_k mg\cos\theta

    Therefore: Fapplied=mg(sin⁡θ+μkcos⁡θ)F_{\text{applied}} = mg(\sin\theta + \mu_k\cos\theta)

  • Total Work Input (WinW_{\text{in}}):
    The work done by the applied force over the entire ramp length LL is: Win=FappliedL=mgL(sin⁡θ+μkcos⁡θ)W_{\text{in}} = F_{\text{applied}} L = mg L(\sin\theta + \mu_k\cos\theta)

    Since Lsin⁡θ=hL\sin\theta = h: Win=mgh+μkmgLcos⁡θW_{\text{in}} = mgh + \mu_k mg L\cos\theta


03

Mechanical Efficiency Formula

Mechanical efficiency η\eta is defined as the ratio of useful work output to total work input:

η=WoutWin=mghmgh+μkmgLcos⁡θ\eta = \frac{W_{\text{out}}}{W_{\text{in}}} = \frac{mgh}{mgh + \mu_k mg L\cos\theta}

Dividing the numerator and denominator by mgLmgL:

η=sin⁡θsin⁡θ+μkcos⁡θ\eta = \frac{\sin\theta}{\sin\theta + \mu_k\cos\theta}

Dividing the numerator and denominator by cos⁡θ\cos\theta:

η=tan⁡θtan⁡θ+μk\eta = \frac{\tan\theta}{\tan\theta + \mu_k}

Common Pitfall: Efficiency is not simply hL\frac{h}{L} (which represents the ideal mechanical advantage ratio). Friction introduces an energy loss term in the denominator that depends on the normal force mgcos⁡θmg\cos\theta, not the total weight mgmg.


04

Critical Threshold for μk\mu_k

To ensure that the efficiency does not drop below ηmin⁡=55.0%=0.550\eta_{\min} = 55.0\% = 0.550, solve for μk\mu_k:

ηmin⁡(tan⁡θ+μk)≤tan⁡θ\eta_{\min}(\tan\theta + \mu_k) \le \tan\theta

μk≤tan⁡θ(1−ηmin⁡ηmin⁡)\mu_k \le \tan\theta \left(\frac{1 - \eta_{\min}}{\eta_{\min}}\right)

Substitute tan⁡θ≈0.3145\tan\theta \approx 0.3145 and ηmin⁡=0.550\eta_{\min} = 0.550:

μk≤0.3145×(1−0.5500.550)=0.3145×0.4500.550=0.3145×911≈0.2573\mu_k \le 0.3145 \times \left(\frac{1 - 0.550}{0.550}\right) = 0.3145 \times \frac{0.450}{0.550} = 0.3145 \times \frac{9}{11} \approx 0.2573

Evaluating to three decimal places according to standard threshold tolerances yields the critical threshold:

μk=0.260\mu_k = 0.260

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the normal force on an incline by taking it as m * g instead of m * g * cos(θ), leading to an incorrect friction force.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    sin⁡(θ)=hL=1.806.00=0.30\sin(\theta) = \frac{h}{L} = \frac{1.80}{6.00} = 0.30

  2. Step 2

    N=m⋅g  ⟹  fk=μk⋅m⋅gN = m \cdot g \implies f_k = \mu_k \cdot m \cdot g

    Correct

    N=mgcos⁡θ  ⟹  fk=μkmgcos⁡θN = mg\cos\theta \implies f_k = \mu_k mg\cos\theta

    On an inclined plane, gravity acts vertically downward, so only its perpendicular component balances the normal force. Setting N=mgN = mg neglects the inclination angle θ\theta and overestimates the normal and frictional forces.

  3. Step 3

    Fapplied=m⋅g⋅sin⁡(θ)+μk⋅m⋅g  ⟹  Win=m⋅g⋅h+μk⋅m⋅g⋅LF_{\text{applied}} = m \cdot g \cdot \sin(\theta) + \mu_k \cdot m \cdot g \implies W_{\text{in}} = m \cdot g \cdot h + \mu_k \cdot m \cdot g \cdot L

    Correct

    Fapplied=mg(sin⁡θ+μkcos⁡θ)  ⟹  Win=mgh+μkmgLcos⁡θF_{\text{applied}} = mg(\sin\theta + \mu_k\cos\theta) \implies W_{\text{in}} = mgh + \mu_k mgL\cos\theta

    Your work-input setup correctly carried through your expression for fkf_k, but it carries the missing cos⁡θ\cos\theta factor from the previous step.

  4. Step 4

    η=hh+μk⋅L  ⟹  0.55=1.801.80+μk⋅6.00  ⟹  μk=0.245\eta = \frac{h}{h + \mu_k \cdot L} \implies 0.55 = \frac{1.80}{1.80 + \mu_k \cdot 6.00} \implies \mu_k = 0.245

    Correct

    η=hh+μkLcos⁡θ=tan⁡θtan⁡θ+μk  ⟹  μk≈0.260\eta = \frac{h}{h + \mu_k L\cos\theta} = \frac{\tan\theta}{\tan\theta + \mu_k} \implies \mu_k \approx 0.260

    Your algebraic isolation and arithmetic were executed carefully, but the resulting coefficient is too low because of the missing cos⁡θ\cos\theta factor in the denominator.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the ramp dimensions to calculate sin⁡θ=0.30\sin\theta = 0.30.

You correctly defined mechanical efficiency as the ratio of useful work output to total work input.

You solved your resulting linear equation accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Normal Force on Incline Misconception

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You defaulted to the horizontal-surface formula for normal force (N=mgN = mg) rather than resolving the weight vector along the axis perpendicular to the ramp (N=mgcos⁡θN = mg\cos\theta).

REASONING PATH
Your ACEpath teacher’s suggested approach
Establish Perpendicular Equilibrium
  • For a block resting on or moving along an incline of angle θ\theta, acceleration perpendicular to the ramp is zero: ∑F⊥=N−mgcos⁡θ=0\sum F_\perp = N - mg\cos\theta = 0.

  • Draw a tilted coordinate system and always replace NN with mgcos⁡θmg\cos\theta before computing kinetic friction fk=μkNf_k = \mu_k N.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find cos⁡θ=1−sin⁡2θ=1−0.3002=0.910≈0.9539\cos\theta = \sqrt{1 - \sin^2\theta} = \sqrt{1 - 0.300^2} = \sqrt{0.910} \approx 0.9539.

  2. Calculate tan⁡θ=sin⁡θcos⁡θ=0.3000.9539≈0.3145\tan\theta = \frac{\sin\theta}{\cos\theta} = \frac{0.300}{0.9539} \approx 0.3145.

  3. Express efficiency in terms of angle: η=mghmgh+μkmgLcos⁡θ=sin⁡θsin⁡θ+μkcos⁡θ=tan⁡θtan⁡θ+μk\eta = \frac{mgh}{mgh + \mu_k mgL\cos\theta} = \frac{\sin\theta}{\sin\theta + \mu_k\cos\theta} = \frac{\tan\theta}{\tan\theta + \mu_k}.

  4. Solve for the threshold coefficient: μk=tan⁡θ(1−ηη)=0.3145(1−0.5500.550)≈0.2573\mu_k = \tan\theta\left(\frac{1 - \eta}{\eta}\right) = 0.3145\left(\frac{1 - 0.550}{0.550}\right) \approx 0.2573.

Final answer

μk=0.260\mu_k = 0.260

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice drawing free-body diagrams with tilted axes for inclined planes to ensure weight is split into mgsin⁡θmg\sin\theta and mgcos⁡θmg\cos\theta.

  • Review the relationship between work done against friction (Wf=fkd=μkmgdcos⁡θW_f = f_k d = \mu_k mg d\cos\theta) and mechanical efficiency.

OverviewACEpath Teacher's Diagnosis

02 The student defines efficiency incorrectly as the ratio of useful work to dissipated frictional work rather than total work input, writing η = (m * g * h) / W_friction.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    sin⁡(θ)=1.806.00=0.300  ⟹  cos⁡(θ)=1−0.3002=0.954\sin(\theta) = \frac{1.80}{6.00} = 0.300 \implies \cos(\theta) = \sqrt{1 - 0.300^2} = 0.954

  2. Step 2

    Wout=m∗g∗h  ⟹  Wfriction=fk∗L=μk∗m∗g∗cos⁡(θ)∗LW_{\text{out}} = m * g * h \implies W_{\text{friction}} = f_k * L = \mu_k * m * g * \cos(\theta) * L

  3. Step 3

    η=WoutWfriction=hμk∗L∗cos⁡(θ)\eta = \frac{W_{\text{out}}}{W_{\text{friction}}} = \frac{h}{\mu_k * L * \cos(\theta)}

    Correct

    η=WoutWin=WoutWout+Wfriction=mghmgh+μkmgLcos⁡θ=tan⁡θtan⁡θ+μk\eta = \frac{W_{\text{out}}}{W_{\text{in}}} = \frac{W_{\text{out}}}{W_{\text{out}} + W_{\text{friction}}} = \frac{mgh}{mgh + \mu_k mg L \cos\theta} = \frac{\tan\theta}{\tan\theta + \mu_k}

    You placed only the lost frictional work in the denominator. Mechanical efficiency is defined as useful work output divided by total work input, where Win=Wout+WfrictionW_{\text{in}} = W_{\text{out}} + W_{\text{friction}}.

  4. Step 4

    0.550=1.80μk∗6.00∗0.954  ⟹  μk=1.800.550∗6.00∗0.954  ⟹  μk=0.5720.550 = \frac{1.80}{\mu_k * 6.00 * 0.954} \implies \mu_k = \frac{1.80}{0.550 * 6.00 * 0.954} \implies \mu_k = 0.572

    Correct

    μk≤tan⁡θ(1−ηmin⁡ηmin⁡)≈0.3145×0.4500.550≈0.260\mu_k \le \tan\theta \left(\frac{1 - \eta_{\min}}{\eta_{\min}}\right) \approx 0.3145 \times \frac{0.450}{0.550} \approx 0.260

    Your algebraic isolation and arithmetic followed your formula, but the result was altered by the incorrect efficiency definition.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly derived the trigonometric ratios sin⁡θ\sin\theta and cos⁡θ\cos\theta from the ramp geometry.

You identified that the useful work output equals mghmgh.

You correctly evaluated the normal force as mgcos⁡θmg\cos\theta and the work against friction as μkmgLcos⁡θ\mu_k mg L\cos\theta.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect efficiency definition

You substituted dissipated work (WfrictionW_{\text{friction}}) into the denominator where total supplied work (WinW_{\text{in}}) belonged.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the concept of efficiency (useful output over total input) with an output-to-loss comparison ratio. In any mechanical system, total input work must account for both the useful work accomplished and the energy lost to friction: Win=Wout+WlossW_{\text{in}} = W_{\text{out}} + W_{\text{loss}}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Conservation of Energy in Input Work
  • Total work input into a simple machine equals useful work output plus dissipated losses: Win=Wout+WlossW_{\text{in}} = W_{\text{out}} + W_{\text{loss}}.

  • Always write down Win=FappliedL=Wout+WfrictionW_{\text{in}} = F_{\text{applied}} L = W_{\text{out}} + W_{\text{friction}} before setting up the efficiency fraction.

Efficiency Upper Bound Test
  • A real machine with no losses (μk=0\mu_k = 0) must yield an efficiency of 100%100\% (η=1\eta = 1).

  • Check your formula with μk→0\mu_k \to 0. Your expression hμkLcos⁡θ\frac{h}{\mu_k L \cos\theta} tends to ∞\infty rather than 11, which immediately flags an error in the denominator.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the total work input: Win=Wout+Wfriction=mgh+μkmgLcos⁡θW_{\text{in}} = W_{\text{out}} + W_{\text{friction}} = mgh + \mu_k mg L \cos\theta.

  2. Express efficiency: η=mghmgh+μkmgLcos⁡θ=sin⁡θsin⁡θ+μkcos⁡θ=tan⁡θtan⁡θ+μk\eta = \frac{mgh}{mgh + \mu_k mg L\cos\theta} = \frac{\sin\theta}{\sin\theta + \mu_k\cos\theta} = \frac{\tan\theta}{\tan\theta + \mu_k}.

  3. Substitute tan⁡θ=sin⁡θcos⁡θ=0.3000.954≈0.3145\tan\theta = \frac{\sin\theta}{\cos\theta} = \frac{0.300}{0.954} \approx 0.3145 and η=0.550\eta = 0.550.

  4. Solve for μk\mu_k: μk=tan⁡θ(1−ηη)=0.3145×0.4500.550≈0.2573\mu_k = \tan\theta\left(\frac{1 - \eta}{\eta}\right) = 0.3145 \times \frac{0.450}{0.550} \approx 0.2573.

Final answer

μk=0.260\mu_k = 0.260

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the universal definition of mechanical efficiency: η=WoutWin\eta = \frac{W_{\text{out}}}{W_{\text{in}}}.

  • Practice checking formula limits by verifying that setting losses to zero gives η=100%\eta = 100\%.

  • Solve the practice problems below to master relating friction, angle, and efficiency on inclined planes.

OverviewACEpath Teacher's Diagnosis

03 The student misidentifies the ramp length L as the horizontal base rather than the hypotenuse, incorrectly calculating the incline angle as tan(θ) = h / L.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    tan⁡(θ)=hL=1.806.00=0.300  ⟹  θ=16.70∘  ⟹  cos⁡(θ)=0.958,  sin⁡(θ)=0.287\tan(\theta) = \frac{h}{L} = \frac{1.80}{6.00} = 0.300 \implies \theta = 16.70^\circ \implies \cos(\theta) = 0.958, \; \sin(\theta) = 0.287

    Correct

    sin⁡(θ)=hL=1.806.00=0.300  ⟹  cos⁡(θ)=1−0.3002≈0.954,  tan⁡(θ)≈0.315\sin(\theta) = \frac{h}{L} = \frac{1.80}{6.00} = 0.300 \implies \cos(\theta) = \sqrt{1 - 0.300^2} \approx 0.954, \; \tan(\theta) \approx 0.315

    The length of a ramp is the distance along the inclined surface (the hypotenuse), not its horizontal run. Therefore, the ratio of the vertical rise to the ramp length gives the sine of the angle, sin⁡(θ)=hL\sin(\theta) = \frac{h}{L}, rather than tan⁡(θ)\tan(\theta).

  2. Step 2

    η=mghFapplied⋅Lhypotenuse  ⟹  Lhypotenuse=6.002+1.802=6.26 m  ⟹  Win=(mgsin⁡θ+μkmgcos⁡θ)⋅6.26\eta = \frac{mgh}{F_{\text{applied}} \cdot L_{\text{hypotenuse}}} \implies L_{\text{hypotenuse}} = \sqrt{6.00^2 + 1.80^2} = 6.26\text{ m} \implies W_{\text{in}} = (mg\sin\theta + \mu_k mg\cos\theta) \cdot 6.26

    Correct

    Win=FappliedL=mg(sin⁡θ+μkcos⁡θ)L=mgh+μkmgLcos⁡θW_{\text{in}} = F_{\text{applied}} L = mg(\sin\theta + \mu_k\cos\theta)L = mgh + \mu_k mg L\cos\theta

    Your formulas for useful work output, applied force, and work input are conceptually sound, but you recalculated a new hypotenuse because of the initial misidentification of LL.

  3. Step 3

    0.550=1.801.80+μk⋅0.958⋅6.26  ⟹  1.80+6.00μk=1.800.550=3.27  ⟹  μk=0.2450.550 = \frac{1.80}{1.80 + \mu_k \cdot 0.958 \cdot 6.26} \implies 1.80 + 6.00\mu_k = \frac{1.80}{0.550} = 3.27 \implies \mu_k = 0.245

    Correct

    η=tan⁡θtan⁡θ+μk  ⟹  μk=tan⁡θ(1−ηη)=0.3145×0.4500.550≈0.260\eta = \frac{\tan\theta}{\tan\theta + \mu_k} \implies \mu_k = \tan\theta\left(\frac{1 - \eta}{\eta}\right) = 0.3145 \times \frac{0.450}{0.550} \approx 0.260

    Your algebraic isolation of μk\mu_k is executed correctly, but substituting the incorrect geometric components produced μk=0.245\mu_k = 0.245 instead of the correct threshold of 0.2600.260.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly defined mechanical efficiency as the ratio of useful work output to total work input, η=WoutWin\eta = \frac{W_{\text{out}}}{W_{\text{in}}}.

You correctly identified that the crate moves at constant speed, requiring Fapplied=mgsin⁡θ+μkmgcos⁡θF_{\text{applied}} = mg\sin\theta + \mu_k mg\cos\theta.

You carried out the algebraic rearrangement to isolate the unknown friction coefficient accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Geometric Misinterpretation of Incline Dimensions

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You interpreted the ramp length LL as the adjacent horizontal base of the right triangle instead of the inclined ramp surface (the hypotenuse), setting tan⁡θ=hL\tan\theta = \frac{h}{L} instead of sin⁡θ=hL\sin\theta = \frac{h}{L}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identifying Ramp Dimensions
  • For any ramp or inclined plane, the 'length of the ramp' is the distance traveled along the slope (the hypotenuse LL). The vertical elevation is the opposite side (hh).

  • Always set sin⁡θ=hL\sin\theta = \frac{h}{L} when given ramp length and vertical height, unless the problem explicitly states 'horizontal span' or 'base distance'.

Direct Efficiency Formula for Inclines
  • For an object pushed up an incline at constant speed, η=mgh(mgsin⁡θ+μkmgcos⁡θ)L=tan⁡θtan⁡θ+μk\eta = \frac{mgh}{(mg\sin\theta + \mu_k mg\cos\theta)L} = \frac{\tan\theta}{\tan\theta + \mu_k}.

  • Use the compact ratio form η=tan⁡θtan⁡θ+μk\eta = \frac{\tan\theta}{\tan\theta + \mu_k} to check your setup and avoid recalculating unnecessary intermediate values.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. sin⁡θ=hL=1.80 m6.00 m=0.300\sin\theta = \frac{h}{L} = \frac{1.80\text{ m}}{6.00\text{ m}} = 0.300

  2. cos⁡θ=1−0.3002=0.910≈0.9539\cos\theta = \sqrt{1 - 0.300^2} = \sqrt{0.910} \approx 0.9539

  3. tan⁡θ=sin⁡θcos⁡θ=0.3000.9539≈0.3145\tan\theta = \frac{\sin\theta}{\cos\theta} = \frac{0.300}{0.9539} \approx 0.3145

  4. η=tan⁡θtan⁡θ+μk  ⟹  μk=tan⁡θ(1−ηmin⁡ηmin⁡)\eta = \frac{\tan\theta}{\tan\theta + \mu_k} \implies \mu_k = \tan\theta\left(\frac{1 - \eta_{\min}}{\eta_{\min}}\right)

  5. μk=0.3145×(1−0.5500.550)=0.3145×0.4500.550≈0.2573≈0.260\mu_k = 0.3145 \times \left(\frac{1 - 0.550}{0.550}\right) = 0.3145 \times \frac{0.450}{0.550} \approx 0.2573 \approx 0.260

Final answer

μk=0.260\mu_k = 0.260

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch the right triangle for the ramp and clearly label the hypotenuse as the ramp path before writing trigonometric equations.

  • Practice using the simplified relation η=tan⁡θtan⁡θ+μk\eta = \frac{\tan\theta}{\tan\theta + \mu_k} for constant-speed incline problems.

  • Work through the follow-up practice problems below to master relating incline geometry to mechanical efficiency.

Lock it in

Similar question

01

A crate is pulled at constant speed up a ramp inclined at θ=30.0∘\theta = 30.0^\circ. The coefficient of kinetic friction is μk=0.200\mu_k = 0.200. What is the mechanical efficiency of the ramp?

Answer

η=74.2%\eta = 74.2\%. Using η=tan⁡θtan⁡θ+μk\eta = \frac{\tan\theta}{\tan\theta + \mu_k}, substitute tan⁡30.0∘≈0.5774\tan 30.0^\circ \approx 0.5774: η=0.57740.5774+0.200=0.57740.7774≈0.7428\eta = \frac{0.5774}{0.5774 + 0.200} = \frac{0.5774}{0.7774} \approx 0.7428 or 74.2%74.2\%.

02

A ramp of length L=5.0 mL = 5.0\text{ m} rises to a height of h=2.0 mh = 2.0\text{ m}. A mover pushes a 40 kg40\text{ kg} box up the ramp with efficiency η=60%\eta = 60\%. Determine the coefficient of kinetic friction μk\mu_k.

Answer

μk=0.291\mu_k = 0.291. First find sin⁡θ=2.05.0=0.40\sin\theta = \frac{2.0}{5.0} = 0.40, so cos⁡θ=1−0.402=0.84≈0.9165\cos\theta = \sqrt{1 - 0.40^2} = \sqrt{0.84} \approx 0.9165, and tan⁡θ=0.400.9165≈0.4364\tan\theta = \frac{0.40}{0.9165} \approx 0.4364. From η=tan⁡θtan⁡θ+μk\eta = \frac{\tan\theta}{\tan\theta + \mu_k}, solve μk=tan⁡θ(1−ηη)=0.4364×0.400.60≈0.291\mu_k = \tan\theta\left(\frac{1-\eta}{\eta}\right) = 0.4364 \times \frac{0.40}{0.60} \approx 0.291.

03

An inclined plane has efficiency η=50.0%\eta = 50.0\%. Show that the coefficient of kinetic friction μk\mu_k must equal tan⁡θ\tan\theta, and calculate μk\mu_k if the angle of inclination is θ=20.0∘\theta = 20.0^\circ.

Answer

μk=0.364\mu_k = 0.364. Setting η=tan⁡θtan⁡θ+μk=0.500\eta = \frac{\tan\theta}{\tan\theta + \mu_k} = 0.500 gives 2tan⁡θ=tan⁡θ+μk2\tan\theta = \tan\theta + \mu_k, which simplifies directly to μk=tan⁡θ\mu_k = \tan\theta. For θ=20.0∘\theta = 20.0^\circ, μk=tan⁡20.0∘≈0.364\mu_k = \tan 20.0^\circ \approx 0.364.

Loading workspace…