Resources
A laboratory demonstration tests the law of inertia using a cart and an untethered test mass. An untethered block of mass rests on a horizontal, frictionless platform mounted atop a cart. The cart travels forward along the -axis at a steady speed of before entering a braking zone. The cart decelerates uniformly to rest at a constant rate . Because the platform is frictionless, no horizontal contact force acts on the block, so by Newton's first law it continues moving at until it strikes the cart's front barrier, sliding a relative distance of along the platform in a time of . (a) State the physical property of the block that causes it to maintain its velocity during the deceleration of the cart. (b) Using the relative kinematic snapshot, determine the magnitude of the cart's deceleration . (c) Calculate the total stopping distance of the cart from the instant braking initiated.
Answer and steps
Final answer
(a) Inertia, which is the intrinsic tendency of an object to resist changes in its state of motion (proportional to its inertial mass ). (b) . (c)
Steps
Part (a): Identifying the Physical Property
According to Newton's first law of motion, an object at rest remains at rest, and an object in motion continues in motion with a constant velocity unless acted upon by a net external force. Because the platform is frictionless, no horizontal force acts on the block once braking begins; thus, its horizontal acceleration is zero.
The physical property responsible for this behavior is inertia, which is the intrinsic tendency of an object to resist changes in its state of motion. The measure of an object's inertia is its inertial mass ().
Part (b): Determining the Cart's Deceleration
Choose the direction of initial motion as positive ().
-
Ground-Frame Displacements:
- The untethered block experiences zero net horizontal force, so it travels at a constant velocity . Its displacement during time is:
- The cart experiences a constant deceleration of magnitude , meaning its acceleration is . Its displacement during the same time interval is:
-
Relative Displacement along the Platform:
- The relative forward sliding distance of the block relative to the cart is the difference between their ground displacements:
-
Solving for :
- Rearranging for the deceleration:
- Substitute and :
Part (c): Calculating the Total Stopping Distance of the Cart
-
Kinematic Equation for Stopping:
- Use the work-energy or kinematic relation , where the final velocity is :
-
Numerical Calculation:
- Substitute and :
Pitfall Note: Be careful not to use as the total stopping time of the cart. The time is simply the elapsed time until the block impacts the front barrier, which occurs before the cart comes fully to rest (the cart stops at ).
Typical errors
01 The student forgets the factor of 1/2 in the kinematic equation for displacement from rest, finding half the true acceleration and thus doubling the stopping distance.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the factor of in the constant-acceleration displacement equation . Because both the cart and the block share the same initial speed , their initial relative velocity is zero (), leading to .
- Step 3Correct
Your kinematic formula relating initial speed, deceleration, and stopping distance was set up correctly, but substituting the incorrect acceleration from part (b) propagated into an erroneous stopping distance.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified inertia as the physical property governed by Newton's first law.
You recognized that the relative motion between the block and cart determines the acceleration.
You applied the correct kinematic relationship to find stopping distance.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou forgot that for motion with constant acceleration starting from rest, the average velocity over the interval is , which introduces the coefficient into the displacement formula .
REASONING PATH
Your ACEpath teacher’s suggested approach- Kinematic Displacement from Rest
When an object starts from rest (or zero relative velocity) and accelerates uniformly at , its displacement is .
Always write the full kinematic relation before dropping zero terms to ensure the factor is never omitted.
CORRECTED PATH
ACEpath Teacher's Demonstration(a) Inertia, (b) , (c) $ x_{} = 8.13_$$
02 The student forgets to square the time in the kinematic formula when solving for acceleration.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
In the constant-acceleration kinematic equation , time must be squared in the acceleration term. Because you wrote instead of , your acceleration calculation was incorrect.
- Step 3Correct
Your kinematic relationship for stopping distance was correctly chosen and executed, but substituting your earlier value of led to an affected final numerical answer.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified inertia as the physical property responsible for maintaining constant velocity under zero net force.
You correctly related the relative displacement between the block and cart to the acceleration term.
You correctly applied the Torricelli kinematic relation to find the stopping distance.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of when setting up the relative displacement formula.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisIncomplete recall or transcription of the position-time equation under constant acceleration, missing the quadratic time dependence .
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Dimensions of Acceleration Terms
Every displacement term must have units of meters: (velocity), whereas (length).
Perform a dimensional check on your formula before substituting numbers to verify that every additive term yields units of distance.
- Recall the Standard Kinematic Form
For motion with constant acceleration, .
Always write down the full symbolic equation with explicit powers before plugging in numerical values.
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute with the correct square: .
Solve for the cart's deceleration: .
Substitute this acceleration into the stopping formula: .
(a) Inertia; (b) ; (c)
03 The student assumes the cart stops completely at t = 0.850 s instead of recognizing that 0.850 s is only the time until the block impacts the barrier.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You treated as the total time it took the cart to stop from to . The given is only the time elapsed until the block hits the front barrier after sliding relative to the cart, while the cart is still moving.
- Step 3Correct
Your kinematic stopping formula is set up correctly, but your numerical result was thrown off by the incorrect acceleration value from the previous step.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified inertia as the fundamental property described by Newton's first law.
You selected the appropriate kinematic relationship to relate stopping distance, initial velocity, and deceleration.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated the duration of an intermediate event (the block sliding relative to the decelerating cart until impact) with the cart's overall stopping time, overlooking the relative motion constraint .
REASONING PATH
Your ACEpath teacher’s suggested approach- Distinguish intermediate events from final states
An event described over time (such as an impact or sliding distance) does not mean the system has reached a zero-velocity state at that moment unless explicitly stated.
Check whether the problem states the vehicle is at rest at time , or whether merely marks a collision or boundary condition while the vehicle is still moving.
- Use relative acceleration for non-inertial/relative sliding
When a zero-acceleration object slides on a decelerating platform of acceleration , their relative acceleration is , giving .
Relate relative displacement directly to relative acceleration rather than applying ground-frame stopping equations prematurely.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the relative motion between the block and cart: since in the ground frame and is directed backwards, the relative acceleration of the block forward along the platform is .
Since both start with the same initial speed , their relative initial velocity is zero: .
Solve for the deceleration: .
Substitute into the stopping distance formula: .
(b) ; (c)
Lock it in
What is the kinematic formula for displacement under constant acceleration when initial velocity ?
. The factor of arises because the average speed over the interval is .
Similar question
A car traveling at brakes with constant deceleration and comes to rest over a time interval of . Using in reverse (or average velocity), calculate its acceleration magnitude and total stopping distance.
Answer
. Total stopping distance is (or ).
A skateboard carrying a loose puck moves at along a smooth horizontal surface. When the skateboard strikes a rough patch and decelerates uniformly, the frictionless puck slides forward by relative to the skateboard in . Determine the deceleration of the skateboard and its stopping distance from the start of the rough patch.
Answer
Relative displacement is . Stopping distance is .
A flatbed truck travels at with an unanchored crate resting on its frictionless bed, located behind the cab. The truck brakes with a constant deceleration of . (a) How long does it take for the crate to slide into the cab? (b) Does the truck stop before the crate hits the cab?
Answer
(a) Relative motion: . (b) Stopping time of truck is . Since , the crate impacts the cab well before the truck comes to rest.