Resources

A thin uniform hoop of mass M=2.40 kgM = 2.40\text{ kg} and radius R=0.500 mR = 0.500\text{ m} (with rotational inertia I=MR2I = MR^2 about its central perpendicular axis) is spinning freely on a frictionless axle. A mechanical brake shoe applies a constant tangential frictional braking force Ff=6.00 NF_f = 6.00\text{ N} directly against the outer rim until the hoop comes completely to rest after turning through exactly θ=8.00 revolutions\theta = 8.00\text{ revolutions}. Using the work-energy theorem for rotational systems (Wnc=ΔKrotW_{\text{nc}} = \Delta K_{\text{rot}}), determine the initial rotational kinetic energy Krot,0K_{\text{rot,0}} of the hoop at the instant the brake was first engaged.

Answer and steps

Final answer

Krot,0=151 JK_{\text{rot,0}} = 151\text{ J}

Steps

01

Convert angular displacement to radians

Rotational equations require the angular displacement Δθ\Delta\theta to be expressed in radians rather than revolutions:

Δθ=8.00 rev×2π rad1 rev=16.0π rad≈50.27 rad\Delta\theta = 8.00\text{ rev} \times \frac{2\pi\text{ rad}}{1\text{ rev}} = 16.0\pi\text{ rad} \approx 50.27\text{ rad}

02

Calculate the braking torque and work done

The frictional force FfF_f acts tangentially at the outer rim of the hoop (at a distance equal to the radius RR from the axis of rotation). Because the friction opposes the direction of rotation, the braking torque τ\tau is negative:

τ=−FfR=−(6.00 N)(0.500 m)=−3.00 N⋅m\tau = -F_f R = -(6.00\text{ N})(0.500\text{ m}) = -3.00\text{ N}\cdot\text{m}

Since the torque is constant throughout the motion, the rotational work WncW_{\text{nc}} done by this non-conservative braking force is:

Wnc=τ Δθ=(−3.00 N⋅m)(16.0π rad)=−48.0π J≈−150.8 JW_{\text{nc}} = \tau\,\Delta\theta = (-3.00\text{ N}\cdot\text{m})(16.0\pi\text{ rad}) = -48.0\pi\text{ J} \approx -150.8\text{ J}

Alternatively, one can recognize that the total arc distance traveled by the rim is s=R Δθs = R\,\Delta\theta, giving the translational work of the tangential force directly: W=−Ffs=−Ff(R Δθ)W = -F_f s = -F_f(R\,\Delta\theta), which yields the exact same expression.

03

Apply the rotational work-energy theorem

According to the work-energy theorem for rotational motion:

Wnc=ΔKrot=Krot,f−Krot,0W_{\text{nc}} = \Delta K_{\text{rot}} = K_{\text{rot,f}} - K_{\text{rot,0}}

The hoop is brought completely to rest, so its final rotational kinetic energy is zero (Krot,f=0K_{\text{rot,f}} = 0):

−48.0π J=0−Krot,0-48.0\pi\text{ J} = 0 - K_{\text{rot,0}}

Krot,0=48.0π J≈151 JK_{\text{rot,0}} = 48.0\pi\text{ J} \approx 151\text{ J}

Key Pitfall to Avoid: While the mass M=2.40 kgM = 2.40\text{ kg} is provided, solving for the angular acceleration α\alpha and initial angular speed ω0\omega_0 using kinematics is unnecessary. Applying the work-energy theorem directly equates the magnitude of the braking work to the initial kinetic energy in a single step, avoiding rounding errors.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 A student forgets to convert revolutions to radians when calculating rotational work, using θ = 8.00 directly and obtaining 24.0 J.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ=Ff∗R=6.00∗0.500=3.00 N⋅m\tau = F_f * R = 6.00 * 0.500 = 3.00\text{ N}\cdot\text{m}

  2. Step 2

    Wnc=−τ∗θ=−3.00∗8.00=−24.0 JW_{\text{nc}} = -\tau * \theta = -3.00 * 8.00 = -24.0\text{ J}

    Correct

    Wnc=−τ Δθ=−(3.00 N⋅m)(8.00×2π rad)=−48.0π J≈−151 JW_{\text{nc}} = -\tau \,\Delta\theta = -(3.00\text{ N}\cdot\text{m})(8.00 \times 2\pi\text{ rad}) = -48.0\pi\text{ J} \approx -151\text{ J}

    You plugged in the angular displacement directly as 8.00 rev8.00\text{ rev} instead of converting it to radians (8.00×2π=16.0π rad8.00 \times 2\pi = 16.0\pi\text{ rad}). In standard SI rotational formulas, work W=τ ΔθW = \tau\,\Delta\theta requires Δθ\Delta\theta in radians.

  3. Step 3

    ΔKrot=0−Krot,0=Wnc  ⟹  Krot,0=24.0 J\Delta K_{\text{rot}} = 0 - K_{\text{rot,0}} = W_{\text{nc}} \implies K_{\text{rot,0}} = 24.0\text{ J}

    Correct

    ΔKrot=0−Krot,0=Wnc  ⟹  Krot,0=48.0π J≈151 J\Delta K_{\text{rot}} = 0 - K_{\text{rot,0}} = W_{\text{nc}} \implies K_{\text{rot,0}} = 48.0\pi\text{ J} \approx 151\text{ J}

    Your application of the work-energy theorem was logically sound, but the final numerical value was off because it inherited the uncoverted angle from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the magnitude of the braking torque using τ=FfR\tau = F_f R.

You correctly recognized that the braking torque does negative work opposing rotation.

You properly formulated the rotational work-energy theorem with final kinetic energy set to zero.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Angle unit omission (revolutions to radians)

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You substituted angular displacement in units of revolutions directly into the rotational work formula W=τ ΔθW = \tau\,\Delta\theta without converting to SI radians (1 rev=2π rad1\text{ rev} = 2\pi\text{ rad}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Angular Units in Dynamic Formulas
  • In dynamic and energetic formulas like W=τ ΔθW = \tau\,\Delta\theta and Krot=12Iω2K_{\text{rot}} = \frac{1}{2}I\omega^2, angles and angular speeds must always be in radians or radians per second.

  • Multiply revolutions by 2π rad/rev2\pi\text{ rad/rev} before performing any work or energy calculations.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Δθ=8.00 rev×2π rad/rev=16.0π rad≈50.27 rad\Delta\theta = 8.00\text{ rev} \times 2\pi\text{ rad/rev} = 16.0\pi\text{ rad} \approx 50.27\text{ rad}

  2. Wnc=−τ Δθ=−(3.00 N⋅m)(16.0π rad)=−48.0π J≈−151 JW_{\text{nc}} = -\tau\,\Delta\theta = -(3.00\text{ N}\cdot\text{m})(16.0\pi\text{ rad}) = -48.0\pi\text{ J} \approx -151\text{ J}

  3. Krot,0=−Wnc=48.0π J≈151 JK_{\text{rot,0}} = -W_{\text{nc}} = 48.0\pi\text{ J} \approx 151\text{ J}

Final answer

Krot,0≈151 JK_{\text{rot,0}} \approx 151\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down explicit units next to numbers during substitution to catch unit mismatches like rev\text{rev} versus rad\text{rad}.

  • Practice checking dimensional consistency: a joule is equivalent to a newton-meter-radian, so angular displacement must be dimensionless radians.

OverviewACEpath Teacher's Diagnosis

02 A student confuses the formula for torque by dividing by the radius instead of multiplying, resulting in an incorrect torque and initial kinetic energy.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    θ=8.00∗2π=16.0π rad\theta = 8.00 * 2\pi = 16.0\pi\text{ rad}

  2. Step 2

    τ=FfR=6.000.500=12.0 N⋅m\tau = \frac{F_f}{R} = \frac{6.00}{0.500} = 12.0\text{ N}\cdot\text{m}

    Correct

    τ=FfR=(6.00 N)(0.500 m)=3.00 N⋅m\tau = F_f R = (6.00\text{ N})(0.500\text{ m}) = 3.00\text{ N}\cdot\text{m}

    Torque is the product of the tangential force and the lever arm (τ=FfR\tau = F_f R), not the quotient. Dividing by RR resulted in 12.0 N⋅m12.0\text{ N}\cdot\text{m} instead of 3.00 N⋅m3.00\text{ N}\cdot\text{m}.

  3. Step 3

    Wnc=−τ∗θ=−12.0∗16.0π=−192π J≈−603 JW_{\text{nc}} = -\tau * \theta = -12.0 * 16.0\pi = -192\pi\text{ J} \approx -603\text{ J}

    Correct

    Wnc=−τ Δθ=−(3.00 N⋅m)(16.0π rad)=−48.0π J≈−151 JW_{\text{nc}} = -\tau\,\Delta\theta = -(3.00\text{ N}\cdot\text{m})(16.0\pi\text{ rad}) = -48.0\pi\text{ J} \approx -151\text{ J}

    Your formula for rotational work was set up correctly, but the numerical result was affected by the incorrect torque value from the previous step.

  4. Step 4

    Krot,0=−Wnc=603 JK_{\text{rot,0}} = -W_{\text{nc}} = 603\text{ J}

    Correct

    Krot,0=−Wnc=48.0π J≈151 JK_{\text{rot,0}} = -W_{\text{nc}} = 48.0\pi\text{ J} \approx 151\text{ J}

    You applied the work-energy theorem accurately to solve for initial kinetic energy, but the final value carried over the earlier calculation error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the rotational displacement from revolutions into radians.

You correctly related rotational work to torque and angular displacement.

You correctly used the work-energy theorem to equate initial kinetic energy to the work done against friction.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula inversion for torque

You accidentally divided by the radius RR rather than multiplying when computing torque.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the product relationship in torque (τ=rF⊥\tau = r F_\perp) with a ratio formula, leading to inverted units and an inflated torque magnitude.

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit check on torque
  • Torque is measured in newton-meters (N⋅m\text{N}\cdot\text{m}), which requires multiplying force by distance.

  • Always check that the units of your expression yield N⋅m\text{N}\cdot\text{m}: [F][R]=N⋅m[F][R] = \text{N}\cdot\text{m}, whereas [F]/[R]=N/m[F]/[R] = \text{N}/\text{m}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. τ=FfR=(6.00 N)(0.500 m)=3.00 N⋅m\tau = F_f R = (6.00\text{ N})(0.500\text{ m}) = 3.00\text{ N}\cdot\text{m}

  2. Wnc=−τ Δθ=−(3.00 N⋅m)(16.0π rad)=−48.0π J≈−150.8 JW_{\text{nc}} = -\tau\,\Delta\theta = -(3.00\text{ N}\cdot\text{m})(16.0\pi\text{ rad}) = -48.0\pi\text{ J} \approx -150.8\text{ J}

  3. Krot,0=−Wnc=48.0π J≈151 JK_{\text{rot,0}} = -W_{\text{nc}} = 48.0\pi\text{ J} \approx 151\text{ J}

Final answer

Krot,0=151 JK_{\text{rot,0}} = 151\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the rotational definition of torque as force times perpendicular lever arm.

  • Use dimensional analysis to confirm that the units of torque are N⋅m\text{N}\cdot\text{m} before carrying the value into energy calculations.

OverviewACEpath Teacher's Diagnosis

03 A student uses the angle conversion factor of π radians per revolution instead of 2π, halving the angular displacement and resulting in 75.4 J.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    τ=Ff∗R=6.00∗0.500=3.00 N⋅m\tau = F_f * R = 6.00 * 0.500 = 3.00\text{ N}\cdot\text{m}

  2. Step 2

    θ=8.00∗π=8.00π rad\theta = 8.00 * \pi = 8.00\pi\text{ rad}

    Correct

    Δθ=8.00 rev×2π rad1 rev=16.0π rad\Delta\theta = 8.00\text{ rev} \times \frac{2\pi\text{ rad}}{1\text{ rev}} = 16.0\pi\text{ rad}

    One full revolution corresponds to 2π rad2\pi\text{ rad}, not π rad\pi\text{ rad}. Multiplying 8.00 rev8.00\text{ rev} by π\pi instead of 2π2\pi gave half of the actual angular displacement.

  3. Step 3

    Wnc=−τ∗θ=−3.00∗8.00π=−24.0π J≈−75.4 JW_{\text{nc}} = -\tau * \theta = -3.00 * 8.00\pi = -24.0\pi\text{ J} \approx -75.4\text{ J}

    Correct

    Wnc=−τ Δθ=−(3.00 N⋅m)(16.0π rad)=−48.0π J≈−151 JW_{\text{nc}} = -\tau\,\Delta\theta = -(3.00\text{ N}\cdot\text{m})(16.0\pi\text{ rad}) = -48.0\pi\text{ J} \approx -151\text{ J}

    Your formula for non-conservative work opposing rotation was correct, but this step inherited the halved angular displacement value from the previous step.

  4. Step 4

    Krot,0=−Wnc=75.4 JK_{\text{rot,0}} = -W_{\text{nc}} = 75.4\text{ J}

    Correct

    Krot,0=−Wnc=48.0π J≈151 JK_{\text{rot,0}} = -W_{\text{nc}} = 48.0\pi\text{ J} \approx 151\text{ J}

    You correctly applied the work-energy theorem Wnc=0−Krot,0W_{\text{nc}} = 0 - K_{\text{rot,0}}, but the resulting kinetic energy is half the true value due to the earlier conversion error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the braking torque has magnitude τ=FfR\tau = F_f R.

You properly recognized that the braking work is negative because the torque opposes the rotation.

You correctly applied the work-energy theorem ΔKrot=Wnc\Delta K_{\text{rot}} = W_{\text{nc}} to isolate Krot,0K_{\text{rot,0}} directly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Revolution-to-radian conversion error

You multiplied by π\pi instead of 2π2\pi when converting revolutions to radians.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the angular measure of a semi-circle (π rad=180∘\pi\text{ rad} = 180^\circ) with a complete revolution (2π rad=360∘2\pi\text{ rad} = 360^\circ).

REASONING PATH
Your ACEpath teacher’s suggested approach
Full Circle Radians Check
  • One complete revolution equals the circumference of a unit circle: 1 rev=2π rad1\text{ rev} = 2\pi\text{ rad}.

  • Always write out unit fractions explicitly, multiplying by 2π rad1 rev\frac{2\pi\text{ rad}}{1\text{ rev}} whenever an angle is given in revolutions.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert revolutions to radians: Δθ=8.00 rev×2πradrev=16.0π rad\Delta\theta = 8.00\text{ rev} \times 2\pi\frac{\text{rad}}{\text{rev}} = 16.0\pi\text{ rad}.

  2. Calculate the braking work done by torque: Wnc=−τ Δθ=−(3.00 N⋅m)(16.0π rad)=−48.0π J≈−150.8 JW_{\text{nc}} = -\tau\,\Delta\theta = -(3.00\text{ N}\cdot\text{m})(16.0\pi\text{ rad}) = -48.0\pi\text{ J} \approx -150.8\text{ J}.

  3. Apply the rotational work-energy relation Wnc=Krot,f−Krot,0=0−Krot,0W_{\text{nc}} = K_{\text{rot,f}} - K_{\text{rot,0}} = 0 - K_{\text{rot,0}} to find Krot,0=−(−48.0π J)≈151 JK_{\text{rot,0}} = -(-48.0\pi\text{ J}) \approx 151\text{ J}.

Final answer

Krot,0=151 JK_{\text{rot,0}} = 151\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review radian conversions for standard rotational units (revolutions, cycles, degrees).

  • Practice rotational work-energy problems using explicit dimensional cancellation for angle units.

Lock it in

Similar question

01

A flywheel experiences a constant retarding torque of 4.50 N⋅m4.50\text{ N}\cdot\text{m}. How much rotational work is done on the flywheel as it completes 12.0 revolutions12.0\text{ revolutions}?

Answer

W=−τ Δθ=−(4.50 N⋅m)(12.0×2π rad)=−108π J≈−339 JW = -\tau\,\Delta\theta = -(4.50\text{ N}\cdot\text{m})(12.0 \times 2\pi\text{ rad}) = -108\pi\text{ J} \approx -339\text{ J}.

02

A solid cylinder with rotational inertia I=0.800 kg⋅m2I = 0.800\text{ kg}\cdot\text{m}^2 is rotating at an unknown initial speed. A brake pad applies a constant tangential force of 15.0 N15.0\text{ N} at radius R=0.200 mR = 0.200\text{ m} until the cylinder stops after 5.00 revolutions5.00\text{ revolutions}. Find the initial rotational kinetic energy Krot,0K_{\text{rot,0}}.

Answer

Torque is τ=FR=(15.0)(0.200)=3.00 N⋅m\tau = F R = (15.0)(0.200) = 3.00\text{ N}\cdot\text{m}. Angular displacement is Δθ=5.00×2π=10.0π rad\Delta\theta = 5.00 \times 2\pi = 10.0\pi\text{ rad}. Braking work is W=−τ Δθ=−(3.00)(10.0π)=−30.0π J≈−94.2 JW = -\tau\,\Delta\theta = -(3.00)(10.0\pi) = -30.0\pi\text{ J} \approx -94.2\text{ J}. By the work-energy theorem, Krot,0=−W=30.0π J≈94.2 JK_{\text{rot,0}} = -W = 30.0\pi\text{ J} \approx 94.2\text{ J}.

03

A grinding wheel of radius R=0.150 mR = 0.150\text{ m} has initial rotational kinetic energy Krot,0=450 JK_{\text{rot,0}} = 450\text{ J}. A tool pressed against the rim exerts a normal force of 40.0 N40.0\text{ N}. If the kinetic friction coefficient between the tool and rim is μk=0.250\mu_k = 0.250, how many complete revolutions will the wheel turn before coming to rest?

Answer

Friction force is Ff=μkFN=0.250×40.0=10.0 NF_f = \mu_k F_N = 0.250 \times 40.0 = 10.0\text{ N}. Braking torque is τ=FfR=(10.0)(0.150)=1.50 N⋅m\tau = F_f R = (10.0)(0.150) = 1.50\text{ N}\cdot\text{m}. From W=−Krot,0W = -K_{\text{rot,0}}, we get τ Δθ=450 J  ⟹  Δθ=4501.50=300 rad\tau\,\Delta\theta = 450\text{ J} \implies \Delta\theta = \frac{450}{1.50} = 300\text{ rad}. In revolutions: N=3002π≈47.7 revolutionsN = \frac{300}{2\pi} \approx 47.7\text{ revolutions} (47 complete revolutions).

Loading workspace…