Resources

An automated data acquisition system measures a current of I=18.5 mAI = 18.5\text{ mA} passing through an ohmic precision sensor resistor of known resistance R=2.40 kΩR = 2.40\,\mathrm{k}\Omega wired in series with an ammeter. If the total circuit loop consists solely of this resistor, the ideal ammeter, and an uncalibrated DC voltage source, determine the terminal potential difference VV supplied by the source in volts (V\text{V}).

Answer and steps

Final answer

44.4 V44.4\text{ V}

Steps

01

Identify the circuit components and ideal behavior

The circuit forms a single series loop consisting of:

  • A DC voltage source providing terminal potential difference VV
  • A resistor of resistance R=2.40 kΩR = 2.40\text{ k}\Omega
  • An ideal ammeter measuring a current of I=18.5 mAI = 18.5\text{ mA}

An ideal ammeter has zero internal resistance (Rammeter=0 ΩR_{\text{ammeter}} = 0\ \Omega), which means there is no potential drop across it. Therefore, by Kirchhoff's loop rule, the entire terminal potential difference supplied by the voltage source drops across the precision sensor resistor:

V=VRV = V_R


02

Convert quantities to standard SI units

Before applying the governing relationship, convert the given values from prefixed units into base SI units (A\text{A} and Ω\Omega):

  • Current: I=18.5 mA=18.5×10−3 AI = 18.5\text{ mA} = 18.5 \times 10^{-3}\text{ A}
  • Resistance: R=2.40 kΩ=2.40×103 ΩR = 2.40\text{ k}\Omega = 2.40 \times 10^{3}\ \Omega

Common Pitfall: Forgetting to convert milliamperes (mA\text{mA}) and kilo-ohms (kΩ\text{k}\Omega) into amperes (A\text{A}) and ohms (Ω\Omega) can lead to power-of-ten calculation errors. Notice here that the prefix factors 10−310^{-3} and 10310^3 conveniently cancel each other out (10−3×103=110^{-3} \times 10^3 = 1).


03

Calculate the terminal potential difference using Ohm's Law

According to Ohm's law, the voltage drop across an ohmic resistor is directly proportional to the current flowing through it:

V=I⋅RV = I \cdot R

Substitute the given values into the equation:

V=(18.5×10−3 A)⋅(2.40×103 Ω)V = (18.5 \times 10^{-3}\text{ A}) \cdot (2.40 \times 10^{3}\ \Omega)

V=18.5⋅2.40=44.4 VV = 18.5 \cdot 2.40 = 44.4\text{ V}

The terminal potential difference supplied by the DC source is 44.4 V44.4\text{ V}.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student ignores the metric prefixes for current and resistance, substituting numerical values directly as base SI units.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    V=I×RV = I \times R

  2. Step 2

    V=18.5×2.40V = 18.5 \times 2.40

    Correct

    V=(18.5×10−3 A)⋅(2.40×103 Ω)V = (18.5 \times 10^{-3}\text{ A}) \cdot (2.40 \times 10^{3}\ \Omega)

    You substituted the numerical values directly without accounting for the metric prefixes. Current given as 18.5 mA18.5\text{ mA} represents 18.5×10−3 A18.5 \times 10^{-3}\text{ A}, and resistance given as 2.40 kΩ2.40\text{ k}\Omega represents 2.40×103 Ω2.40 \times 10^{3}\ \Omega.

  3. Step 3

    V=44.4 VV = 44.4\text{ V}

    Correct

    V=44.4 VV = 44.4\text{ V}

    You calculated the product accurately and stated the final answer in volts. Your final value matches because the milli- prefix (10−310^{-3}) and kilo- prefix (10310^3) happen to cancel out (10−3×103=110^{-3} \times 10^3 = 1).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified Ohm's law (V=I⋅RV = I \cdot R) as the relationship needed to find the terminal potential difference.

You correctly performed the arithmetic multiplication of 18.5×2.40=44.418.5 \times 2.40 = 44.4.

You assigned the correct SI unit of volts (V\text{V}) to your final potential difference.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of metric prefixes in physical formula substitution

You substituted the numbers 18.518.5 and 2.402.40 directly without writing out their powers of ten or noting that mA×kΩ=V\text{mA} \times \text{k}\Omega = \text{V}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated prefixed measurements as if they were base SI units, overlooking that formulas like V=I⋅RV = I \cdot R strictly require current in amperes (A\text{A}) and resistance in ohms (Ω\Omega) unless prefix cancellation is explicitly tracked.

REASONING PATH
Your ACEpath teacher’s suggested approach
Convert Prefixes to Standard SI Base Units
  • Before substituting into physical laws, express all prefixed quantities in scientific notation using base units: milli-=10−3\text{milli-} = 10^{-3} and kilo-=103\text{kilo-} = 10^{3}.

  • Write I=18.5 mA=18.5×10−3 AI = 18.5\text{ mA} = 18.5 \times 10^{-3}\text{ A} and R=2.40 kΩ=2.40×103 ΩR = 2.40\text{ k}\Omega = 2.40 \times 10^{3}\ \Omega before multiplying.

Verify Prefix Cancellation
  • One volt is defined as one ampere-ohm (1 V=1 A⋅Ω1\text{ V} = 1\text{ A} \cdot \Omega). A product yields volts directly only when the prefix exponents sum to zero ((−3)+3=0(-3) + 3 = 0).

  • Always write out the powers of ten (10−3)(103)=1(10^{-3})(10^3) = 1 so you do not accidentally rely on accidental cancellation.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert both given quantities into base SI units: I=18.5 mA=18.5×10−3 AI = 18.5\text{ mA} = 18.5 \times 10^{-3}\text{ A} and R=2.40 kΩ=2.40×103 ΩR = 2.40\text{ k}\Omega = 2.40 \times 10^{3}\ \Omega.

  2. Substitute these values into Ohm's law: V=(18.5×10−3 A)⋅(2.40×103 Ω)V = (18.5 \times 10^{-3}\text{ A}) \cdot (2.40 \times 10^{3}\ \Omega).

  3. Group the numerical coefficients and powers of ten: V=(18.5×2.40)×(10−3×103) V=44.4×1 V=44.4 VV = (18.5 \times 2.40) \times (10^{-3} \times 10^{3})\text{ V} = 44.4 \times 1\text{ V} = 44.4\text{ V}.

Final answer

44.4 V44.4\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Form the habit of rewriting every prefixed quantity in scientific notation with base units as your very first step before plugging numbers into equations.

  • Practice problems where current and resistance prefixes do not cancel (such as microamperes with kilo-ohms) to ensure you do not miss power-of-ten factors.

OverviewACEpath Teacher's Diagnosis

02 The student incorrectly uses Ohm's law as V = I / R instead of V = I × R, resulting in an incorrect potential difference.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    V=IRV = \frac{I}{R}

    Correct

    V=I⋅RV = I \cdot R

    Ohm's law states that potential difference is the product of current and resistance, not their quotient.

  2. Step 2

    I=18.5×10−3 A, R=2.40×103 ΩI = 18.5 \times 10^{-3}\text{ A},\ R = 2.40 \times 10^3\ \Omega

  3. Step 3

    V=18.5×10−32.40×103V = \frac{18.5 \times 10^{-3}}{2.40 \times 10^3}

    Correct

    V=(18.5×10−3 A)(2.40×103 Ω)V = (18.5 \times 10^{-3}\text{ A})(2.40 \times 10^3\ \Omega)

    Your substitution followed your formula from Step 1, but the values should be multiplied rather than divided.

  4. Step 4

    V=7.71×10−6 VV = 7.71 \times 10^{-6}\text{ V}

    Correct

    V=44.4 VV = 44.4\text{ V}

    The final calculation is affected by the formula error in Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the given values for current and resistance from the problem statement.

You correctly converted both quantities from prefixed metric units into standard SI units.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect Ohm's Law Formula

You wrote V=IRV = \frac{I}{R} instead of multiplying current by resistance, V=I⋅RV = I \cdot R.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You inverted the relationship between current, voltage, and resistance. Ohm's law relates these variables by I=VRI = \frac{V}{R}, which solves for voltage as V=I⋅RV = I \cdot R. Dividing current by resistance yields units of A/Ω=A2/V\text{A}/\Omega = \text{A}^2/\text{V}, not volts.

REASONING PATH
Your ACEpath teacher’s suggested approach
Rearrange Ohm's Law Correctly
  • V=I⋅RV = I \cdot R, I=VRI = \frac{V}{R}, and R=VIR = \frac{V}{I}

  • When solving for potential difference VV, multiply current II by resistance RR.

Perform a Dimensional Unit Check
  • 1 V=1 A×1 Ω1\text{ V} = 1\text{ A} \times 1\ \Omega

  • Check your units before calculating: multiplying amperes by ohms yields volts, whereas dividing amperes by ohms does not.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State Ohm's law relating potential difference, current, and resistance: V=I⋅RV = I \cdot R.

  2. Substitute the SI-converted values: V=(18.5×10−3 A)⋅(2.40×103 Ω)V = (18.5 \times 10^{-3}\text{ A}) \cdot (2.40 \times 10^{3}\ \Omega).

  3. Multiply the factors: V=18.5×2.40×10−3+3=44.4 VV = 18.5 \times 2.40 \times 10^{-3+3} = 44.4\text{ V}.

Final answer

44.4 V44.4\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Use the Ohm's law triangle with VV at the apex and I,RI, R at the base to quickly verify the correct algebraic form before substituting numbers.

  • Practice checking the product of powers of ten (10−3×103=100=110^{-3} \times 10^3 = 10^0 = 1) to simplify arithmetic in circuit problems.

OverviewACEpath Teacher's Diagnosis

03 The student incorrectly converts milliamperes to amperes by multiplying by 10³ instead of 10⁻³.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    V=I×RV = I \times R

  2. Step 2

    I=18.5×103 AI = 18.5 \times 10^3\text{ A}

    Correct

    I=18.5 mA=18.5×10−3 AI = 18.5\text{ mA} = 18.5 \times 10^{-3}\text{ A}

    The metric prefix milli- (m\text{m}) represents one-thousandth (10−310^{-3}), not one thousand (10310^3). Multiplying by 10310^3 treats milliamperes as kiloamperes.

  3. Step 3

    R=2.40×103 ΩR = 2.40 \times 10^3\ \Omega

  4. Step 4

    V=(18.5×103)×(2.40×103)V = (18.5 \times 10^3) \times (2.40 \times 10^3)

    Correct

    V=(18.5×10−3 A)⋅(2.40×103 Ω)V = (18.5 \times 10^{-3}\text{ A}) \cdot (2.40 \times 10^3\ \Omega)

    You substituted your converted values correctly into the formula, but the expression carries forward the erroneous exponent from Step 2.

  5. Step 5

    V=4.44×107 VV = 4.44 \times 10^7\text{ V}

    Correct

    V=44.4 VV = 44.4\text{ V}

    Your arithmetic evaluation was carried out accurately based on the substituted values, but the final value is incorrect due to the earlier unit conversion mistake.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified Ohm's law (V=IRV = I R) to calculate the terminal voltage.

You properly converted the resistance from kilo-ohms to base ohms (2.40×103 Ω2.40 \times 10^3\ \Omega).

You executed the arithmetic and exponent multiplication accurately from your substituted numbers.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric prefix sign confusion (milli vs. kilo)

You wrote 10310^3 instead of 10−310^{-3} for the milli- prefix.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the submultiple prefix milli- (10−310^{-3}) with a positive power of ten (10310^3), perhaps associating the numeral 1,000 with multiplication by +3+3 in the exponent rather than division by 1,000.

REASONING PATH
Your ACEpath teacher’s suggested approach
Metric Submultiples vs. Multiples
  • Prefixes for fractions of a unit (milli-, micro-, nano-) use negative powers of ten: 1 m=10−31\text{ m} = 10^{-3}, 1 μ=10−61\ \mu = 10^{-6}. Prefixes for multiples (kilo-, mega-) use positive powers: 1 k=1031\text{ k} = 10^3, 1 M=1061\text{ M} = 10^6.

  • Whenever you see a small unit like milliamperes (mA\text{mA}), remind yourself that a milliampere is much smaller than an ampere, so the exponent must be negative: 1 mA=10−3 A1\text{ mA} = 10^{-3}\text{ A}.

Prefix Exponent Cancellation Check
  • When multiplying milli (10−310^{-3}) by kilo (10310^3), the powers of ten sum to zero: 10−3×103=100=110^{-3} \times 10^3 = 10^0 = 1.

  • Use the product of mA\text{mA} and kΩ\text{k}\Omega directly as volts: (18.5)(2.40)=44.4 V(18.5)(2.40) = 44.4\text{ V}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Express the current using the negative power of ten: I=18.5 mA=18.5×10−3 AI = 18.5\text{ mA} = 18.5 \times 10^{-3}\text{ A}.

  2. Keep the correct resistance conversion: R=2.40×103 ΩR = 2.40 \times 10^3\ \Omega.

  3. Substitute both into Ohm's law: V=(18.5×10−3 A)⋅(2.40×103 Ω)=18.5⋅2.40⋅(10−3⋅103) VV = (18.5 \times 10^{-3}\text{ A}) \cdot (2.40 \times 10^3\ \Omega) = 18.5 \cdot 2.40 \cdot (10^{-3} \cdot 10^3)\text{ V}.

Final answer

V=44.4 VV = 44.4\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review common SI prefixes and practice matching submultiples (m, μ\mu, n, p) to their negative powers of ten.

  • Solve circuit problems involving mixed prefixes (such as mA\text{mA} with kΩ\text{k}\Omega or μA\mu\text{A} with MΩ\text{M}\Omega) to get comfortable with exponent cancellation.

Lock it in

Similar question

01

A diagnostic sensor resistor has a resistance of R=120 ΩR = 120\ \Omega and carries an operating current of I=45 mAI = 45\text{ mA}. Calculate the potential difference VV across the sensor in volts.

Answer

V=5.4 VV = 5.4\text{ V}. First convert current to base SI units: I=45 mA=45×10−3 AI = 45\text{ mA} = 45 \times 10^{-3}\text{ A}. Then apply Ohm's law: V=I⋅R=(45×10−3 A)(120 Ω)=5.4 VV = I \cdot R = (45 \times 10^{-3}\text{ A})(120\ \Omega) = 5.4\text{ V}.

02

A micro-sensor with internal resistance R=6.8 kΩR = 6.8\text{ k}\Omega draws a current of I=250 μAI = 250\ \mu\text{A}. Determine the voltage drop VV across the sensor in volts.

Answer

V=1.7 VV = 1.7\text{ V}. Convert both quantities into base SI units: I=250 μA=250×10−6 A=2.50×10−4 AI = 250\ \mu\text{A} = 250 \times 10^{-6}\text{ A} = 2.50 \times 10^{-4}\text{ A} and R=6.8 kΩ=6.8×103 ΩR = 6.8\text{ k}\Omega = 6.8 \times 10^{3}\ \Omega. Apply Ohm's law: V=I⋅R=(2.50×10−4 A)(6.8×103 Ω)=1.7 VV = I \cdot R = (2.50 \times 10^{-4}\text{ A})(6.8 \times 10^{3}\ \Omega) = 1.7\text{ V}.

03

An ultra-sensitive electrometer circuit measures a leakage current of I=80 nAI = 80\text{ nA} through a protective barrier resistor of R=450 MΩR = 450\text{ M}\Omega. Calculate the terminal potential difference VV across the barrier in volts.

Answer

V=36 VV = 36\text{ V}. Convert both quantities to base SI units: I=80 nA=80×10−9 AI = 80\text{ nA} = 80 \times 10^{-9}\text{ A} and R=450 MΩ=450×106 ΩR = 450\text{ M}\Omega = 450 \times 10^{6}\ \Omega. Apply Ohm's law: V=I⋅R=(80×10−9 A)(450×106 Ω)=36,000×10−3 V=36 VV = I \cdot R = (80 \times 10^{-9}\text{ A})(450 \times 10^{6}\ \Omega) = 36,000 \times 10^{-3}\text{ V} = 36\text{ V}.

Loading workspace…