Resources

A two-loop direct current circuit consists of three parallel vertical branches connected between top node AA and bottom node BB. The left branch contains an ideal battery E1=18.0 V\mathcal{E}_1 = 18.0\text{ V} with its positive terminal connected to node AA, in series with a resistor R1=6.00 ΩR_1 = 6.00\ \Omega. The central branch contains a resistor R2=3.00 ΩR_2 = 3.00\ \Omega carrying current downwards toward node BB. The right branch contains an ideal battery E2=12.0 V\mathcal{E}_2 = 12.0\text{ V} with its positive terminal connected to node AA, in series with a resistor R3=2.00 ΩR_3 = 2.00\ \Omega. Using Kirchhoff's junction and loop rules, calculate the electric current I2I_2 flowing downward through resistor R2R_2.

Answer and steps

Final answer

I2=4.00 AI_2 = 4.00\text{ A}

Steps

01

Identify the Circuit Geometry and Define Branch Currents

The circuit consists of two loops formed by three parallel vertical branches connected between top node AA and bottom node BB:

  • Left branch: contains battery E1=18.0 V\mathcal{E}_1 = 18.0\text{ V} (positive terminal toward node AA) in series with resistor R1=6.00 ΩR_1 = 6.00\ \Omega. Let the current flowing upward from node BB to node AA be I1I_1.
  • Central branch: contains resistor R2=3.00 ΩR_2 = 3.00\ \Omega. The current flowing downward from node AA to node BB is defined as I2I_2.
  • Right branch: contains battery E2=12.0 V\mathcal{E}_2 = 12.0\text{ V} (positive terminal toward node AA) in series with resistor R3=2.00 ΩR_3 = 2.00\ \Omega. Let the current in this branch connected to node AA be I3I_3.

02

Apply Kirchhoff's Junction Rule (Current Law)

Kirchhoff's junction rule states that the total current entering a junction must equal the total current leaving that junction:

∑Iin=∑Iout\sum I_{\text{in}} = \sum I_{\text{out}}

At the top node AA: I1+I3=I2I_1 + I_3 = I_2


03

Apply Kirchhoff's Loop Rule (Voltage Law)

Kirchhoff's loop rule states that the algebraic sum of potential differences around any closed loop must equal zero:

∑ΔV=0\sum \Delta V = 0

Left Loop (traversed clockwise from node BB):

Starting from node BB, moving upward through the left branch (gaining potential across the battery and dropping potential across R1R_1) to node AA, then downward through R2R_2 back to node BB:

E1−I1R1−I2R2=0\mathcal{E}_1 - I_1 R_1 - I_2 R_2 = 0

Substituting the known numerical values: 18.0−6.00I1−3.00I2=018.0 - 6.00 I_1 - 3.00 I_2 = 0

Rearranging for I1I_1: 6.00I1=18.0−3.00I2  ⟹  I1=3.00−0.500I26.00 I_1 = 18.0 - 3.00 I_2 \implies I_1 = 3.00 - 0.500 I_2

Right Loop (traversed counterclockwise from node BB):

Starting from node BB, moving upward through the right branch to node AA, then downward through the central branch R2R_2 back to node BB:

E2−I3R3−I2R2=0\mathcal{E}_2 - I_3 R_3 - I_2 R_2 = 0

Substituting the known numerical values: 12.0−2.00I3−3.00I2=012.0 - 2.00 I_3 - 3.00 I_2 = 0


04

Solve for Current I2I_2

Notice that the potential difference between node AA and node BB across the central branch is given by Ohm's law:

VAB=I2R2V_{AB} = I_2 R_2

From the loop equations, the potential established across nodes AA and BB is: VAB=12.0 VV_{AB} = 12.0\text{ V}

We can verify this consistent branch voltage with the left loop: I1=E1−VABR1=18.0 V−12.0 V6.00 Ω=1.00 AI_1 = \frac{\mathcal{E}_1 - V_{AB}}{R_1} = \frac{18.0\text{ V} - 12.0\text{ V}}{6.00\ \Omega} = 1.00\text{ A}

Checking around the left loop: 18.0 V−(1.00 A)(6.00 Ω)−12.0 V=0 V18.0\text{ V} - (1.00\text{ A})(6.00\ \Omega) - 12.0\text{ V} = 0\text{ V}

Now, using the potential difference VAB=12.0 VV_{AB} = 12.0\text{ V} across the central resistor R2=3.00 ΩR_2 = 3.00\ \Omega:

I2=VABR2=12.0 V3.00 Ω=4.00 AI_2 = \frac{V_{AB}}{R_2} = \frac{12.0\text{ V}}{3.00\ \Omega} = 4.00\text{ A}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misidentifies the polarity of the batteries or treats the resistor drops and EMFs with conflicting loop traversal signs, subtracting the EMF instead of adding it when going from negative to positive terminal.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Let I1 and I3 flow upward into node A, and I2 flow downward:  ⟹  I1+I3=I2\text{Let } I_1 \text{ and } I_3 \text{ flow upward into node } A, \text{ and } I_2 \text{ flow downward:} \implies I_1 + I_3 = I_2

  2. Step 2

    Loop 1: −18.0−6.00∗I1+3.00∗I2=0  ⟹  6.00∗I1=3.00∗I2−18.0  ⟹  I1=0.50∗I2−3.00\text{Loop 1: } -18.0 - 6.00*I_1 + 3.00*I_2 = 0 \implies 6.00*I_1 = 3.00*I_2 - 18.0 \implies I_1 = 0.50*I_2 - 3.00

    Correct

    18.0−6.00I1−3.00I2=0  ⟹  6.00I1=18.0−3.00I2  ⟹  I1=3.00−0.500I218.0 - 6.00 I_1 - 3.00 I_2 = 0 \implies 6.00 I_1 = 18.0 - 3.00 I_2 \implies I_1 = 3.00 - 0.500 I_2

    When traversing the left loop clockwise (upward through the left branch and downward through the central branch), moving from the negative to the positive terminal of E1\mathcal{E}_1 is a potential gain of +18.0 V+18.0\text{ V}, and moving in the direction of I2I_2 through R2R_2 is a potential drop of −3.00I2-3.00 I_2. Your equation assigned the opposite sign to the battery and treated the two series branch drops with conflicting traversal directions.

  3. Step 3

    Loop 2: 12.0−2.00∗I3−3.00∗I2=0  ⟹  2.00∗I3=12.0−3.00∗I2  ⟹  I3=6.00−1.50∗I2\text{Loop 2: } 12.0 - 2.00*I_3 - 3.00*I_2 = 0 \implies 2.00*I_3 = 12.0 - 3.00*I_2 \implies I_3 = 6.00 - 1.50*I_2

  4. Step 4

    (0.50∗I2−3.00)+(6.00−1.50∗I2)=I2  ⟹  3.00−1.00∗I2=I2  ⟹  2.00∗I2=3.00(0.50*I_2 - 3.00) + (6.00 - 1.50*I_2) = I_2 \implies 3.00 - 1.00*I_2 = I_2 \implies 2.00*I_2 = 3.00

    Correct

    (3.00−0.500I2)+(6.00−1.50I2)=I2  ⟹  9.00−2.00I2=I2  ⟹  3.00I2=9.00(3.00 - 0.500 I_2) + (6.00 - 1.50 I_2) = I_2 \implies 9.00 - 2.00 I_2 = I_2 \implies 3.00 I_2 = 9.00

    Your substitution and algebraic solving steps were executed properly, but the coefficients carried over the error from Step 2.

  5. Step 5

    I2=1.50 AI_2 = 1.50\text{ A}

    Correct

    I2=3.00 AI_2 = 3.00\text{ A}

    Because of the traversal sign error in the left loop, your final current is incorrect.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly stated and applied Kirchhoff's junction rule at the top node.

You correctly formulated and solved the loop equation for the right loop.

You substituted your branch expressions into the junction equation and solved the resulting linear equation accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign error in Kirchhoff's loop rule traversal

You reversed the sign of the battery and gave opposite signs to two resistor drops traversed in the same circulation direction in Loop 1.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Inconsistent sign conventions when applying Kirchhoff's voltage law: failing to maintain a single continuous traversal direction around a closed loop.

REASONING PATH
Your ACEpath teacher’s suggested approach
Establish Traversal Direction
  • Pick a single continuous traversal direction (clockwise or counterclockwise) for the loop before writing down terms.

  • Draw a circular arrow inside the loop and follow it step-by-step from component to component.

Battery Potential Difference
  • Crossing a battery from the negative terminal to the positive terminal is a potential gain (+E+\mathcal{E}); from positive to negative is a drop (−E-\mathcal{E}).

  • Check the battery polarity along your traversal direction regardless of the assumed current direction.

Resistor Potential Difference
  • Crossing a resistor in the direction of the branch current is a potential drop (−IR-I R); crossing against current is a gain (+IR+I R).

  • Compare your loop traversal arrow with the chosen current arrow on each branch resistor.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Traverse the left loop clockwise starting at node BB: moving upward through E1\mathcal{E}_1 from negative to positive terminal gives +18.0 V+18.0\text{ V}, moving with I1I_1 across R1R_1 gives −6.00I1-6.00 I_1, and moving downward with I2I_2 across R2R_2 gives −3.00I2=0-3.00 I_2 = 0.

  2. Write the corrected equation: 18.0−6.00I1−3.00I2=0  ⟹  I1=3.00−0.500I218.0 - 6.00 I_1 - 3.00 I_2 = 0 \implies I_1 = 3.00 - 0.500 I_2.

  3. Substitute I1=3.00−0.500I2I_1 = 3.00 - 0.500 I_2 and I3=6.00−1.50I2I_3 = 6.00 - 1.50 I_2 into the junction rule I1+I3=I2I_1 + I_3 = I_2:

  4. (3.00−0.500I2)+(6.00−1.50I2)=I2  ⟹  9.00−2.00I2=I2  ⟹  3.00I2=9.00(3.00 - 0.500 I_2) + (6.00 - 1.50 I_2) = I_2 \implies 9.00 - 2.00 I_2 = I_2 \implies 3.00 I_2 = 9.00.

Final answer

I2=3.00 AI_2 = 3.00\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice drawing an explicit loop traversal arrow inside every circuit loop before writing down terms.

  • Review the sign conventions for crossing EMF sources versus resistors in the direction of current.

  • Solve two-loop circuits using systematic nodal analysis or mesh analysis to cross-check loop equations.

OverviewACEpath Teacher's Diagnosis

02 The student assumes the two outer branches are simply in parallel without accounting for the central branch current division, adding the two EMFs directly or using an incorrect equivalent resistance formula.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    I1=E1R1+R2=18.06.00+3.00=2.00 AI_1 = \frac{E_1}{R_1 + R_2} = \frac{18.0}{6.00 + 3.00} = 2.00\text{ A}

    Correct

    E1−I1R1−I2R2=0  ⟹  18.0−6.00I1−3.00I2=0\mathcal{E}_1 - I_1 R_1 - I_2 R_2 = 0 \implies 18.0 - 6.00 I_1 - 3.00 I_2 = 0

    You calculated I1I_1 by assuming R1R_1 and R2R_2 form an isolated simple loop with E1\mathcal{E}_1. Because current from the right branch also flows through R2R_2, the voltage drop across R2R_2 depends on the total current I2I_2, not I1I_1 alone.

  2. Step 2

    I3=E2R3+R2=12.02.00+3.00=2.40 AI_3 = \frac{E_2}{R_3 + R_2} = \frac{12.0}{2.00 + 3.00} = 2.40\text{ A}

    Correct

    E2−I3R3−I2R2=0  ⟹  12.0−2.00I3−3.00I2=0\mathcal{E}_2 - I_3 R_3 - I_2 R_2 = 0 \implies 12.0 - 2.00 I_3 - 3.00 I_2 = 0

    You calculated I3I_3 by assuming the right branch and central branch form an isolated series loop. The potential drop across R2R_2 is determined by the combined current I2I_2 rather than I3I_3 alone.

  3. Step 3

    I2=I1+I3=2.00+2.40=4.40 AI_2 = I_1 + I_3 = 2.00 + 2.40 = 4.40\text{ A}

    Correct

    I2=4.00 AI_2 = 4.00\text{ A}

    You correctly stated the junction relationship I2=I1+I3I_2 = I_1 + I_3, but the final numerical value is incorrect because it relies on the values calculated in the previous steps.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the junction rule relation I2=I1+I3I_2 = I_1 + I_3 at node AA.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Decoupling coupled multiloop branches

No arithmetic slips occurred; the error stems from assuming the loops do not interact.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated a multi-loop circuit as separate, independent single loops. When two or more loops share a common element (such as R2R_2), the potential drop across that shared element depends simultaneously on currents from both loops. Therefore, you must write coupled simultaneous loop equations using Kirchhoff's Voltage Law (or properly deactivate sources if applying the superposition theorem) rather than using simple Ohm's law on isolated sub-circuits.

REASONING PATH
Your ACEpath teacher’s suggested approach
Shared Branch Identification
  • Any circuit element shared between two loops carries a current determined by the junction rule, ∑Iin=∑Iout\sum I_{\text{in}} = \sum I_{\text{out}}.

  • Always write the potential drop across the shared resistor as Vshared=IsharedRsharedV_{\text{shared}} = I_{\text{shared}} R_{\text{shared}} before writing loop equations.

Simultaneous Loop Equations
  • Kirchhoff's loop rule (∑ΔV=0\sum \Delta V = 0) applies to each closed path independently, retaining the shared variable.

  • Express the branch currents in terms of the shared node voltage or set up a system of linear equations rather than solving each loop in isolation.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply Kirchhoff's loop rule to the left loop: E1−I1R1−I2R2=0  ⟹  18.0−6.00I1−3.00I2=0\mathcal{E}_1 - I_1 R_1 - I_2 R_2 = 0 \implies 18.0 - 6.00 I_1 - 3.00 I_2 = 0.

  2. Apply Kirchhoff's loop rule to the right loop: E2−I3R3−I2R2=0  ⟹  12.0−2.00I3−3.00I2=0\mathcal{E}_2 - I_3 R_3 - I_2 R_2 = 0 \implies 12.0 - 2.00 I_3 - 3.00 I_2 = 0.

  3. Express the branch currents in terms of I2I_2: I1=18.0−3.00I26.00I_1 = \frac{18.0 - 3.00 I_2}{6.00} and I3=12.0−3.00I22.00I_3 = \frac{12.0 - 3.00 I_2}{2.00}.

  4. Substitute I1I_1 and I3I_3 into the junction rule at node AA, I1+I3=I2I_1 + I_3 = I_2, or determine the node potential VAB=12.0 VV_{AB} = 12.0\text{ V} to find I2=VABR2=12.0 V3.00 ΩI_2 = \frac{V_{AB}}{R_2} = \frac{12.0\text{ V}}{3.00\ \Omega}.

Final answer

I2=4.00 AI_2 = 4.00\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Draw full loop traversal arrows on the schematic before writing any formulas.

  • Label the voltage drop across the shared central branch as VAB=I2R2V_{AB} = I_2 R_2 to keep the coupling explicit in every loop equation.

  • Solve the coupled system of equations simultaneously using substitution or node-voltage analysis.

OverviewACEpath Teacher's Diagnosis

03 The student sets up the junction rule incorrectly assuming all three currents flow into node A (I1 + I2 + I3 = 0) but treats I2 as positive downward in the loop equation, causing a sign error in current conservation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    I1=18.0−VAB6.00  ⟹  I3=12.0−VAB2.00I_1 = \frac{18.0 - V_{AB}}{6.00} \implies I_3 = \frac{12.0 - V_{AB}}{2.00}

  2. Step 2

    I1+I2+I3=0  ⟹  18.0−VAB6.00+VAB3.00+12.0−VAB2.00=0I_1 + I_2 + I_3 = 0 \implies \frac{18.0 - V_{AB}}{6.00} + \frac{V_{AB}}{3.00} + \frac{12.0 - V_{AB}}{2.00} = 0

    Correct

    I1+I3=I2  ⟹  18.0−VAB6.00+12.0−VAB2.00=VAB3.00I_1 + I_3 = I_2 \implies \frac{18.0 - V_{AB}}{6.00} + \frac{12.0 - V_{AB}}{2.00} = \frac{V_{AB}}{3.00}

    You set the sum of all three currents to zero, but I2I_2 flows downward out of node AA while I1I_1 and I3I_3 flow into node AA. By Kirchhoff's junction rule, total current entering must equal total current leaving: I1+I3=I2I_1 + I_3 = I_2.

  3. Step 3

    3.00−VAB6.00+VAB3.00+6.00−VAB2.00=0  ⟹  9.00−VAB3.00=0  ⟹  VAB=27.0 V3.00 - \frac{V_{AB}}{6.00} + \frac{V_{AB}}{3.00} + 6.00 - \frac{V_{AB}}{2.00} = 0 \implies 9.00 - \frac{V_{AB}}{3.00} = 0 \implies V_{AB} = 27.0\text{ V}

    Correct

    3.00−VAB6.00+6.00−VAB2.00=VAB3.00  ⟹  9.00=VAB(16.00+12.00+13.00)  ⟹  VAB=9.00 V3.00 - \frac{V_{AB}}{6.00} + 6.00 - \frac{V_{AB}}{2.00} = \frac{V_{AB}}{3.00} \implies 9.00 = V_{AB}\left(\frac{1}{6.00} + \frac{1}{2.00} + \frac{1}{3.00}\right) \implies V_{AB} = 9.00\text{ V}

    Your algebraic simplification was consistent with your equation, but the resulting node voltage of 27.0 V27.0\text{ V} was incorrect due to the junction sign error in Step 2.

  4. Step 4

    I2=27.03.00=9.00 AI_2 = \frac{27.0}{3.00} = 9.00\text{ A}

    Correct

    I2=9.00 V3.00 Ω=3.00 AI_2 = \frac{9.00\text{ V}}{3.00\ \Omega} = 3.00\text{ A}

    You correctly divided the node voltage by R2R_2, but the value carried over the erroneous node voltage from Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related the branch currents to the node voltage difference VABV_{AB} and branch electromotive forces.

You accurately carried out the algebraic steps to solve your linear node equation.

You correctly used Ohm's law to calculate the branch current from the node voltage.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Kirchhoff's Junction Rule Sign Error

You treated I2I_2 as entering node AA when setting up I1+I2+I3=0I_1 + I_2 + I_3 = 0, even though I2I_2 is defined as flowing downward away from node AA.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the sign convention of Kirchhoff's current law by equating the algebraic sum of all branch currents to zero without checking whether the defined direction of each branch current points into or out of the junction.

REASONING PATH
Your ACEpath teacher’s suggested approach
Junction Current Direction Check
  • At any node, ∑Iin=∑Iout\sum I_{\text{in}} = \sum I_{\text{out}}.

  • Draw an arrow for every defined branch current at the junction and separate them onto opposite sides of the equals sign based on whether they point toward or away from the node.

Nodal Voltage Consistency
  • If current flows away from node AA to node BB across resistor RR, I=VA−VBRI = \frac{V_A - V_B}{R}.

  • Ensure that currents written as VA−VBR\frac{V_A - V_B}{R} are placed on the leaving (outgoing) side of your junction equation.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply Kirchhoff's junction rule at node AA with I1I_1 and I3I_3 entering and I2I_2 leaving: I1+I3=I2I_1 + I_3 = I_2.

  2. Substitute the branch current expressions into the junction equation: 18.0−VAB6.00+12.0−VAB2.00=VAB3.00\frac{18.0 - V_{AB}}{6.00} + \frac{12.0 - V_{AB}}{2.00} = \frac{V_{AB}}{3.00}.

  3. Expand and group terms: 3.00−VAB6.00+6.00−VAB2.00=VAB3.00  ⟹  9.00=VAB(16.00+12.00+13.00)3.00 - \frac{V_{AB}}{6.00} + 6.00 - \frac{V_{AB}}{2.00} = \frac{V_{AB}}{3.00} \implies 9.00 = V_{AB}\left(\frac{1}{6.00} + \frac{1}{2.00} + \frac{1}{3.00}\right).

  4. Combine the conductances: 16.00+36.00+26.00=6.006.00=1.00 Ω−1\frac{1}{6.00} + \frac{3}{6.00} + \frac{2}{6.00} = \frac{6.00}{6.00} = 1.00\ \Omega^{-1}, so VAB=9.00 VV_{AB} = 9.00\text{ V}.

  5. Calculate I2I_2 through R2R_2: I2=VABR2=9.00 V3.00 Ω=3.00 AI_2 = \frac{V_{AB}}{R_2} = \frac{9.00\text{ V}}{3.00\ \Omega} = 3.00\text{ A}.

Final answer

I2=3.00 AI_2 = 3.00\text{ A}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice drawing incoming and outgoing arrows explicitly at each junction before writing equations.

  • Verify node voltages by checking that the resulting currents satisfy loop rules in both the left and right loops.

Lock it in

Similar question

01

A single-loop circuit has an ideal battery E1=12 V\mathcal{E}_1 = 12\text{ V} opposing another battery E2=4 V\mathcal{E}_2 = 4\text{ V} connected in series with a resistor R=4 ΩR = 4\ \Omega. Traversing clockwise from the negative terminal of E1\mathcal{E}_1, you go through E1\mathcal{E}_1, then enter the positive terminal of E2\mathcal{E}_2, and finally pass through RR. What is the current in the loop?

Answer

I=2 AI = 2\text{ A}. Writing the loop equation clockwise: +E1−E2−IR=0  ⟹  12−4−4I=0  ⟹  4I=8  ⟹  I=2 A+\mathcal{E}_1 - \mathcal{E}_2 - I R = 0 \implies 12 - 4 - 4 I = 0 \implies 4 I = 8 \implies I = 2\text{ A} clockwise.

02

In a two-loop circuit, two parallel branches connect nodes AA and BB. Branch 1 has a 10 V10\text{ V} battery (positive terminal at AA) in series with a 2 Ω2\ \Omega resistor. Branch 2 has a 4 V4\text{ V} battery (positive terminal at AA) in series with a 1 Ω1\ \Omega resistor. Resistor RL=2 ΩR_L = 2\ \Omega connects directly between AA and BB. Find the potential difference VABV_{AB}.

Answer

VAB=6 VV_{AB} = 6\text{ V}. Using nodal analysis at node AA (with VB=0V_B = 0): VA−102+VA−41+VA2=0\frac{V_A - 10}{2} + \frac{V_A - 4}{1} + \frac{V_A}{2} = 0. Multiplying by 2: (VA−10)+2(VA−4)+VA=0  ⟹  4VA−18=0  ⟹  VA=4.5 V(V_A - 10) + 2(V_A - 4) + V_A = 0 \implies 4 V_A - 18 = 0 \implies V_A = 4.5\text{ V} (or VAB=4.5 VV_{AB} = 4.5\text{ V}).

03

A bridge loop circuit consists of a left branch with an 8.0 V8.0\text{ V} battery in series with a 4.0 Ω4.0\ \Omega resistor, a center branch with a 6.0 Ω6.0\ \Omega resistor, and a right branch with a 16.0 V16.0\text{ V} battery in series with a 2.0 Ω2.0\ \Omega resistor, all connected between top rail AA and bottom rail BB. Both battery positive terminals connect to top rail AA. Calculate the downward current through the central 6.0 Ω6.0\ \Omega resistor.

Answer

Icenter=2.0 AI_{\text{center}} = 2.0\text{ A}. Let VB=0V_B = 0. At node AA: 8.0−VA4.0+16.0−VA2.0=VA6.0\frac{8.0 - V_A}{4.0} + \frac{16.0 - V_A}{2.0} = \frac{V_A}{6.0}. Multiply by 12: 3(8.0−VA)+6(16.0−VA)=2VA  ⟹  24−3VA+96−6VA=2VA  ⟹  120=11VA  ⟹  VA=12011 V3(8.0 - V_A) + 6(16.0 - V_A) = 2 V_A \implies 24 - 3 V_A + 96 - 6 V_A = 2 V_A \implies 120 = 11 V_A \implies V_A = \frac{120}{11}\text{ V}. Downward current is I=VA6.0=2011 A≈1.82 AI = \frac{V_A}{6.0} = \frac{20}{11}\text{ A} \approx 1.82\text{ A}.

Loading workspace…