Resources

An incompressible, non-viscous liquid of density ρ=1.00×103 kg/m3\rho = 1.00 \times 10^3\text{ kg/m}^3 flows steadily through a pipe system that rises vertically by a height of h=3.50 mh = 3.50\text{ m}. At the lower level (point 1), the pipe has a circular cross-sectional diameter of d1=12.0 cmd_1 = 12.0\text{ cm}, the fluid speed is v1=1.80 m/sv_1 = 1.80\text{ m/s}, and the gauge pressure is P1=1.60×105 PaP_1 = 1.60 \times 10^5\text{ Pa}. At the upper level (point 2), the pipe constricts to a diameter of d2=6.00 cmd_2 = 6.00\text{ cm}. Applying the continuity equation together with the work-energy principle (Bernoulli's equation) with g=9.80 m/s2g = 9.80\text{ m/s}^2, determine the flow speed v2v_2 and the gauge pressure P2P_2 at the elevated constriction.

Answer and steps

Final answer

v2=7.20 m/sv_2 = 7.20\text{ m/s}, P2=1.01×105 PaP_2 = 1.01 \times 10^5\text{ Pa}

Steps

01

Find the flow speed v2v_2 using the equation of continuity

For an incompressible fluid undergoing steady flow, the volumetric flow rate remains constant throughout the pipe:

A1v1=A2v2A_1 v_1 = A_2 v_2

The cross-sectional area of a pipe with circular diameter dd is A=πd24A = \frac{\pi d^2}{4}. Substituting this into the continuity equation gives:

πd124v1=πd224v2  ⟹  v2=v1(d1d2)2\frac{\pi d_1^2}{4} v_1 = \frac{\pi d_2^2}{4} v_2 \implies v_2 = v_1 \left(\frac{d_1}{d_2}\right)^2

Substitute the given values (d1=12.0 cmd_1 = 12.0\text{ cm}, d2=6.00 cmd_2 = 6.00\text{ cm}, and v1=1.80 m/sv_1 = 1.80\text{ m/s}):

v2=1.80 m/s⋅(12.0 cm6.00 cm)2=1.80 m/s⋅(2)2=1.80 m/s⋅4=7.20 m/sv_2 = 1.80\text{ m/s} \cdot \left(\frac{12.0\text{ cm}}{6.00\text{ cm}}\right)^2 = 1.80\text{ m/s} \cdot (2)^2 = 1.80\text{ m/s} \cdot 4 = 7.20\text{ m/s}


02

Apply Bernoulli's equation to find the pressure P2P_2

Bernoulli's equation accounts for the conservation of mechanical energy per unit volume along a streamline in an ideal (incompressible, non-viscous) fluid:

P1+12ρv12+ρgy1=P2+12ρv22+ρgy2P_1 + \frac{1}{2}\rho v_1^2 + \rho g y_1 = P_2 + \frac{1}{2}\rho v_2^2 + \rho g y_2

Choose the lower level as the reference height so that y1=0 my_1 = 0\text{ m} and y2=h=3.50 my_2 = h = 3.50\text{ m}. Rearranging to solve for P2P_2:

P2=P1+12ρ(v12−v22)−ρghP_2 = P_1 + \frac{1}{2}\rho (v_1^2 - v_2^2) - \rho g h


03

Compute the energy terms and solve for P2P_2

  1. Kinetic energy term: 12ρ(v12−v22)=12(1.00×103 kg/m3)[(1.80 m/s)2−(7.20 m/s)2]\frac{1}{2}\rho (v_1^2 - v_2^2) = \frac{1}{2}(1.00 \times 10^3\text{ kg/m}^3)\left[(1.80\text{ m/s})^2 - (7.20\text{ m/s})^2\right] 12ρ(v12−v22)=500 kg/m3⋅(3.24 m2/s2−51.84 m2/s2)=500⋅(−48.60) Pa=−24 300 Pa\frac{1}{2}\rho (v_1^2 - v_2^2) = 500\text{ kg/m}^3 \cdot (3.24\text{ m}^2/\text{s}^2 - 51.84\text{ m}^2/\text{s}^2) = 500 \cdot (-48.60)\text{ Pa} = -24\,300\text{ Pa}
  2. Potential energy term: ρgh=(1.00×103 kg/m3)(9.80 m/s2)(3.50 m)=34 300 Pa\rho g h = (1.00 \times 10^3\text{ kg/m}^3)(9.80\text{ m/s}^2)(3.50\text{ m}) = 34\,300\text{ Pa}
  3. Combine terms: P2=1.60×105 Pa−24 300 Pa−34 300 PaP_2 = 1.60 \times 10^5\text{ Pa} - 24\,300\text{ Pa} - 34\,300\text{ Pa} P2=160 000 Pa−58 600 Pa=101 400 Pa≈1.01×105 PaP_2 = 160\,000\text{ Pa} - 58\,600\text{ Pa} = 101\,400\text{ Pa} \approx 1.01 \times 10^5\text{ Pa}

Common Pitfall: Remember that as fluid speeds up and rises, both effects reduce the internal pressure. Be careful not to square the diameter ratio linearly, and ensure diameter units cancel correctly before calculating speed.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses the ratio of diameters directly rather than the ratio of cross-sectional areas in the continuity equation, leading to an incorrect flow speed and downstream pressure.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    d1v1=d2v2  ⟹  v2=v1(d1d2)=1.80×(12.06.00)  ⟹  v2=3.60 m/sd_1 v_1 = d_2 v_2 \implies v_2 = v_1 \left(\frac{d_1}{d_2}\right) = 1.80 \times \left(\frac{12.0}{6.00}\right) \implies v_2 = 3.60\text{ m/s}

    Correct

    A1v1=A2v2  ⟹  v2=v1(d1d2)2=1.80×(12.06.00)2=7.20 m/sA_1 v_1 = A_2 v_2 \implies v_2 = v_1 \left(\frac{d_1}{d_2}\right)^2 = 1.80 \times \left(\frac{12.0}{6.00}\right)^2 = 7.20\text{ m/s}

    The continuity equation equates volumetric flow rate Q=AvQ = A v, not diameter times speed. Because circular cross-sectional area is proportional to the square of diameter (A=πd24A = \frac{\pi d^2}{4}), the speed ratio must scale with (d1/d2)2(d_1/d_2)^2 rather than d1/d2d_1/d_2.

  2. Step 2

    P2=P1+12ρ(v12−v22)−ρgh=1.60×105+0.5(1000)(1.802−3.602)−1000(9.80)(3.50)  ⟹  P2=1.21×105 PaP_2 = P_1 + \frac{1}{2}\rho (v_1^2 - v_2^2) - \rho g h = 1.60 \times 10^5 + 0.5(1000)(1.80^2 - 3.60^2) - 1000(9.80)(3.50) \implies P_2 = 1.21 \times 10^5\text{ Pa}

    Correct

    P2=P1+12ρ(v12−v22)−ρgh=1.60×105−24 300−34 300=1.01×105 PaP_2 = P_1 + \frac{1}{2}\rho (v_1^2 - v_2^2) - \rho g h = 1.60 \times 10^5 - 24\,300 - 34\,300 = 1.01 \times 10^5\text{ Pa}

    Your algebraic rearrangement of Bernoulli's equation and calculation of the potential energy term ρgh=34 300 Pa\rho g h = 34\,300\text{ Pa} were completely sound, but substituting the incorrect speed v2=3.60 m/sv_2 = 3.60\text{ m/s} instead of 7.20 m/s7.20\text{ m/s} led to an incorrect final pressure.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly stated and rearranged Bernoulli's equation to solve for the pressure P2P_2.

You accurately calculated the gravitational potential energy drop ρgh=34 300 Pa\rho g h = 34\,300\text{ Pa}.

You correctly recognized that fluid speed increases when entering a constriction.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Continuity Equation Area Scaling

You related fluid speed linearly to pipe diameter (d1v1=d2v2d_1 v_1 = d_2 v_2) instead of squaring the diameters to represent cross-sectional area.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing linear dimensions (diameter dd) with cross-sectional area (A=πd24A = \frac{\pi d^2}{4}) when applying conservation of volume flow rate A1v1=A2v2A_1 v_1 = A_2 v_2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Area-Diameter Relationship
  • For a circular cross section, A=πr2=πd24A = \pi r^2 = \frac{\pi d^2}{4}. Area scales with the square of the diameter.

  • Always replace A1/A2A_1/A_2 with (d1/d2)2(d_1/d_2)^2 when solving continuity problems involving pipes.

Continuity Equation Verification
  • A1v1=A2v2A_1 v_1 = A_2 v_2 implies that halving the diameter reduces the area by a factor of 4, quadrupling the fluid velocity.

  • Check your speed scaling physically: if diameter is halved, speed must increase by 22=42^2 = 4 times, not 2 times.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the continuity equation with area: A1v1=A2v2  ⟹  πd124v1=πd224v2A_1 v_1 = A_2 v_2 \implies \frac{\pi d_1^2}{4} v_1 = \frac{\pi d_2^2}{4} v_2.

  2. Solve for v2v_2: v2=v1(d1d2)2=1.80 m/s⋅(12.0 cm6.00 cm)2=1.80⋅4=7.20 m/sv_2 = v_1 \left(\frac{d_1}{d_2}\right)^2 = 1.80\text{ m/s} \cdot \left(\frac{12.0\text{ cm}}{6.00\text{ cm}}\right)^2 = 1.80 \cdot 4 = 7.20\text{ m/s}.

  3. Substitute v2=7.20 m/sv_2 = 7.20\text{ m/s} into Bernoulli's equation: P2=1.60×105 Pa+12(1000 kg/m3)[(1.80 m/s)2−(7.20 m/s)2]−(1000 kg/m3)(9.80 m/s2)(3.50 m)P_2 = 1.60 \times 10^5\text{ Pa} + \frac{1}{2}(1000\text{ kg/m}^3)[(1.80\text{ m/s})^2 - (7.20\text{ m/s})^2] - (1000\text{ kg/m}^3)(9.80\text{ m/s}^2)(3.50\text{ m}).

  4. Compute the dynamic pressure change: 12(1000)(3.24−51.84)=500(−48.60)=−24 300 Pa\frac{1}{2}(1000)(3.24 - 51.84) = 500(-48.60) = -24\,300\text{ Pa}.

  5. Combine all pressure contributions: P2=160 000 Pa−24 300 Pa−34 300 Pa=101 400 Pa≈1.01×105 PaP_2 = 160\,000\text{ Pa} - 24\,300\text{ Pa} - 34\,300\text{ Pa} = 101\,400\text{ Pa} \approx 1.01 \times 10^5\text{ Pa}.

Final answer

v2=7.20 m/sv_2 = 7.20\text{ m/s}, P2=1.01×105 PaP_2 = 1.01 \times 10^5\text{ Pa}

NEXT STEPS
Final Takeaways from Your Teacher
  • When applying the equation of continuity A1v1=A2v2A_1 v_1 = A_2 v_2 to circular pipes, write out the area formula A=πd24A = \frac{\pi d^2}{4} explicitly before simplifying.

  • Perform a quick qualitative check: halving a circular pipe's diameter cuts its flow area to one-fourth, which requires a fourfold increase in speed to maintain steady flow.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to square the flow speeds in the kinetic energy density terms of Bernoulli's equation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A1v1=A2v2  ⟹  v2=v1(d1/d2)2=1.80×(12.06.00)2  ⟹  v2=7.20 m/sA_1 v_1 = A_2 v_2 \implies v_2 = v_1 (d_1 / d_2)^2 = 1.80 \times \left(\frac{12.0}{6.00}\right)^2 \implies v_2 = 7.20\text{ m/s}

  2. Step 2

    P1+(12)ρv1+ρgy1=P2+(12)ρv2+ρgy2  ⟹  P2=P1+(12)ρ(v1−v2)−ρghP_1 + \left(\frac{1}{2}\right)\rho v_1 + \rho g y_1 = P_2 + \left(\frac{1}{2}\right)\rho v_2 + \rho g y_2 \implies P_2 = P_1 + \left(\frac{1}{2}\right)\rho (v_1 - v_2) - \rho g h

    Correct

    P1+12ρv12+ρgy1=P2+12ρv22+ρgy2  ⟹  P2=P1+12ρ(v12−v22)−ρghP_1 + \frac{1}{2}\rho v_1^2 + \rho g y_1 = P_2 + \frac{1}{2}\rho v_2^2 + \rho g y_2 \implies P_2 = P_1 + \frac{1}{2}\rho (v_1^2 - v_2^2) - \rho g h

    In Bernoulli's equation, the kinetic energy per unit volume is proportional to the square of the flow speed, 12ρv2\frac{1}{2}\rho v^2. You wrote the linear velocity vv instead of v2v^2, which also makes the units inconsistent with pressure.

  3. Step 3

    P2=1.60×105+0.5(1000)(1.80−7.20)−1000(9.80)(3.50)  ⟹  P2=1.60×105−2700−34300  ⟹  P2=1.23×105 PaP_2 = 1.60 \times 10^5 + 0.5(1000)(1.80 - 7.20) - 1000(9.80)(3.50) \implies P_2 = 1.60 \times 10^5 - 2700 - 34300 \implies P_2 = 1.23 \times 10^5\text{ Pa}

    Correct

    P2=1.60×105 Pa+0.5(1.00×103 kg/m3)[(1.80 m/s)2−(7.20 m/s)2]−34 300 Pa=1.01×105 PaP_2 = 1.60 \times 10^5\text{ Pa} + 0.5(1.00 \times 10^3\text{ kg/m}^3)\left[(1.80\text{ m/s})^2 - (7.20\text{ m/s})^2\right] - 34\,300\text{ Pa} = 1.01 \times 10^5\text{ Pa}

    Your arithmetic was carried out correctly according to your written formula, but the result was altered by the missing squares on the velocities.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied the conservation of mass via the continuity equation.

You accounted for the inverse-square dependence on the pipe diameter ratio.

You accurately identified and substituted the hydrostatic potential energy term ρgh\rho g h.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing Velocity Exponent in Bernoulli's Equation

You wrote the velocity linearly as 12ρv\frac{1}{2}\rho v rather than squaring the speeds to form 12ρv2\frac{1}{2}\rho v^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing kinetic energy density 12ρv2\frac{1}{2}\rho v^2 with a linear momentum or flow term leads to dimensionally inconsistent energy terms.

REASONING PATH
Your ACEpath teacher’s suggested approach
Kinetic Energy Density Form
  • Bernoulli's equation is a statement of work-energy conservation per unit volume; kinetic energy density is 12ρv2\frac{1}{2}\rho v^2.

  • Always verify that speed terms inside Bernoulli's equation carry an exponent of 2 before substituting values.

Dimensional Consistency Check
  • Every term in Bernoulli's equation must have units of pressure (N/m2\text{N/m}^2 or Pa\text{Pa}, which is kg/(m⋅s2)\text{kg}/(\text{m}\cdot\text{s}^2)).

  • Check that ρv2=(kg/m3)(m/s)2=kg/(m⋅s2)=Pa\rho v^2 = (\text{kg/m}^3)(\text{m/s})^2 = \text{kg}/(\text{m}\cdot\text{s}^2) = \text{Pa}, whereas ρv\rho v yields momentum density (kg/(m2⋅s))(\text{kg}/(\text{m}^2\cdot\text{s})), which cannot be added to pressure.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the kinetic energy density terms with velocity squared: 12ρv12\frac{1}{2}\rho v_1^2 and 12ρv22\frac{1}{2}\rho v_2^2.

  2. Evaluate the kinetic pressure drop: 12(1.00×103)[(1.80)2−(7.20)2]=500(3.24−51.84)=−24 300 Pa\frac{1}{2}(1.00 \times 10^3)[(1.80)^2 - (7.20)^2] = 500(3.24 - 51.84) = -24\,300\text{ Pa}.

  3. Subtract both kinetic and gravitational potential losses from P1P_1: P2=160 000 Pa−24 300 Pa−34 300 Pa=101 400 PaP_2 = 160\,000\text{ Pa} - 24\,300\text{ Pa} - 34\,300\text{ Pa} = 101\,400\text{ Pa}.

Final answer

v2=7.20 m/s,P2=1.01×105 Pav_2 = 7.20\text{ m/s},\quad P_2 = 1.01 \times 10^5\text{ Pa}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the mechanical energy origin of Bernoulli's equation to keep the v2v^2 term front of mind.

  • Practice checking the base SI units of each term whenever you write a fluid mechanics equation.

  • Work through the practice problems below to cement the application of both speed and height changes on fluid pressure.

OverviewACEpath Teacher's Diagnosis

03 The student adds the gravitational potential energy term at the elevated point instead of subtracting it when solving for the pressure at the upper level.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A1V1=A2V2  ⟹  V2=V1(d1/d2)2=1.80×(12.06.00)2  ⟹  V2=7.20 m/sA_1 V_1 = A_2 V_2 \implies V_2 = V_1 (d_1 / d_2)^2 = 1.80 \times \left(\frac{12.0}{6.00}\right)^2 \implies V_2 = 7.20\text{ m/s}

  2. Step 2

    P2=P1+12ρ(v12−v22)+ρghP_2 = P_1 + \frac{1}{2}\rho (v_1^2 - v_2^2) + \rho g h

    Correct

    P2=P1+12ρ(v12−v22)−ρghP_2 = P_1 + \frac{1}{2}\rho (v_1^2 - v_2^2) - \rho g h

    When rearranging Bernoulli's equation P1+12ρv12+ρgy1=P2+12ρv22+ρgy2P_1 + \frac{1}{2}\rho v_1^2 + \rho g y_1 = P_2 + \frac{1}{2}\rho v_2^2 + \rho g y_2 with y2−y1=hy_2 - y_1 = h, moving the potential energy term to the left requires subtracting ρgh\rho g h rather than adding it.

  3. Step 3

    P2=1.60×105+0.5(1000)(1.802−7.202)+1000(9.80)(3.50)  ⟹  P2=1.60×105−24300+34300  ⟹  P2=1.70×105 PaP_2 = 1.60 \times 10^5 + 0.5(1000)(1.80^2 - 7.20^2) + 1000(9.80)(3.50) \implies P_2 = 1.60 \times 10^5 - 24300 + 34300 \implies P_2 = 1.70 \times 10^5\text{ Pa}

    Correct

    P2=1.60×105 Pa−24 300 Pa−34 300 Pa=1.01×105 PaP_2 = 1.60 \times 10^5\text{ Pa} - 24\,300\text{ Pa} - 34\,300\text{ Pa} = 1.01 \times 10^5\text{ Pa}

    Because of the plus sign on the hydrostatic term, your numerical sum added 34 300 Pa34\,300\text{ Pa} instead of subtracting it, leading to an elevated pressure rather than a reduced one.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly set up the continuity equation using the inverse square of the diameter ratio.

You calculated the speed v2=7.20 m/sv_2 = 7.20\text{ m/s} accurately.

You correctly calculated the kinetic energy pressure change 12ρ(v12−v22)=−24 300 Pa\frac{1}{2}\rho(v_1^2 - v_2^2) = -24\,300\text{ Pa}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign error in Bernoulli equation algebraic isolation

You accidentally wrote +ρgh+\rho g h instead of −ρgh-\rho g h when isolating P2P_2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You may be confusing the physical insight that potential energy increases with height with the effect on static pressure: as fluid climbs higher along a streamline, static pressure must decrease to supply that potential energy.

REASONING PATH
Your ACEpath teacher’s suggested approach
Physical Direction Check
  • As an ideal fluid rises and speeds up along a streamline, both kinetic and potential energy density increase, so internal pressure must drop.

  • Always verify that P2<P1P_2 < P_1 whenever a fluid both rises and accelerates.

Two-Sided Conservation Setup
  • P1+12ρv12+ρgy1=P2+12ρv22+ρgy2P_1 + \frac{1}{2}\rho v_1^2 + \rho g y_1 = P_2 + \frac{1}{2}\rho v_2^2 + \rho g y_2

  • Write the full conservation equation with positive terms on both sides before subtracting terms to isolate the unknown variable.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write Bernoulli's equation with point 1 at y1=0y_1 = 0 and point 2 at y2=hy_2 = h: P1+12ρv12=P2+12ρv22+ρghP_1 + \frac{1}{2}\rho v_1^2 = P_2 + \frac{1}{2}\rho v_2^2 + \rho g h.

  2. Subtract both dynamic pressure and potential energy from the left side: P2=P1+12ρ(v12−v22)−ρghP_2 = P_1 + \frac{1}{2}\rho (v_1^2 - v_2^2) - \rho g h.

  3. Substitute the numerical values: P2=1.60×105 Pa−24 300 Pa−34 300 Pa=101 400 PaP_2 = 1.60 \times 10^5\text{ Pa} - 24\,300\text{ Pa} - 34\,300\text{ Pa} = 101\,400\text{ Pa}.

Final answer

v2=7.20 m/s,P2=1.01×105 Pav_2 = 7.20\text{ m/s},\quad P_2 = 1.01 \times 10^5\text{ Pa}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the signs of Bernoulli terms when isolating downstream variables.

  • Perform a sanity check on whether pressure should increase or decrease when climbing in elevation.

Lock it in

Similar question

01

Water flows through a horizontal pipe whose radius narrows from r1=4.0 cmr_1 = 4.0\text{ cm} to r2=2.0 cmr_2 = 2.0\text{ cm}. If the speed at the wider section is v1=1.5 m/sv_1 = 1.5\text{ m/s}, find the flow speed v2v_2 in the constriction.

Answer

Using A1v1=A2v2A_1 v_1 = A_2 v_2: v2=v1(r1r2)2=1.5 m/s⋅(4.02.0)2=1.5⋅4=6.0 m/sv_2 = v_1 \left(\frac{r_1}{r_2}\right)^2 = 1.5\text{ m/s} \cdot \left(\frac{4.0}{2.0}\right)^2 = 1.5 \cdot 4 = 6.0\text{ m/s}.

02

An incompressible oil (rho=850 kg/m3\\rho = 850\text{ kg/m}^3) flows steadily through a horizontal pipe. At section 1, d1=10.0 cmd_1 = 10.0\text{ cm}, v1=2.0 m/sv_1 = 2.0\text{ m/s}, and P1=2.00×105 PaP_1 = 2.00 \times 10^5\text{ Pa}. At section 2, the pipe constricts to d2=5.0 cmd_2 = 5.0\text{ cm}. Determine the flow speed v2v_2 and the pressure P2P_2.

Answer
  1. Continuity: v2=v1(d1/d2)2=2.0⋅(10.0/5.0)2=8.0 m/sv_2 = v_1(d_1/d_2)^2 = 2.0 \cdot (10.0/5.0)^2 = 8.0\text{ m/s}.\n2. Bernoulli (horizontal, Δy=0\Delta y = 0): P2=P1+12ρ(v12−v22)=2.00×105+12(850)(2.02−8.02)=200 000−25 500=1.75×105 PaP_2 = P_1 + \frac{1}{2}\rho(v_1^2 - v_2^2) = 2.00 \times 10^5 + \frac{1}{2}(850)(2.0^2 - 8.0^2) = 200\,000 - 25\,500 = 1.75 \times 10^5\text{ Pa}.
03

Water (rho=1.00×103 kg/m3\\rho = 1.00 \times 10^3\text{ kg/m}^3) enters a vertical tapered nozzle at ground level with diameter d1=8.0 cmd_1 = 8.0\text{ cm}, speed v1=2.5 m/sv_1 = 2.5\text{ m/s}, and pressure P1=2.50×105 PaP_1 = 2.50 \times 10^5\text{ Pa}. The nozzle exits at height h=5.0 mh = 5.0\text{ m} above the ground with diameter d2=4.0 cmd_2 = 4.0\text{ cm}. Calculate the exit speed v2v_2 and exit pressure P2P_2 (use g=9.80 m/s2g = 9.80\text{ m/s}^2).

Answer
  1. Continuity: v2=v1(d1/d2)2=2.5⋅(8.0/4.0)2=10.0 m/sv_2 = v_1(d_1/d_2)^2 = 2.5 \cdot (8.0/4.0)^2 = 10.0\text{ m/s}.\n2. Kinetic energy difference: 12ρ(v12−v22)=500(2.52−10.02)=500(6.25−100)=−46 875 Pa\frac{1}{2}\rho(v_1^2 - v_2^2) = 500(2.5^2 - 10.0^2) = 500(6.25 - 100) = -46\,875\text{ Pa}.\n3. Potential energy term: ρgh=1000⋅9.80⋅5.0=49 000 Pa\rho g h = 1000 \cdot 9.80 \cdot 5.0 = 49\,000\text{ Pa}.\n4. Total pressure: P2=250 000−46 875−49 000=154 125 Pa≈1.54×105 PaP_2 = 250\,000 - 46\,875 - 49\,000 = 154\,125\text{ Pa} \approx 1.54 \times 10^5\text{ Pa}.
Loading workspace…