Resources

In a physics lab experiment, a student measures the coefficient of static friction of an aluminum block on an adjustable steel track. The block of mass m=0.750 kgm = 0.750\text{ kg} is connected to a sensitive digital force sensor that pulls parallel to the track. When the track is horizontal (θ=0∘\theta = 0^\circ), the force sensor records a peak pull of Fpull=2.65 NF_{\text{pull}} = 2.65\text{ N} at the exact instant of breakaway. The track is then tilted to an angle θ=22.0∘\theta = 22.0^\circ above the horizontal without the sensor attached. Take g=9.80 m/s2g = 9.80\text{ m/s}^2. (a) Determine the coefficient of static friction μs\mu_s from the horizontal calibration trial. (b) With the track tilted at 22.0∘22.0^\circ, construct the component force balance along the incline and calculate the maximum available static friction force fs,max⁡f_{s,\max}. (c) By comparing the component of gravity down the incline to fs,max⁡f_{s,\max}, determine whether the block remains at rest or begins to slide, and calculate the net force along the incline at the instant of release.

Answer and steps

Final answer

(a) μs=Fpullmg=2.65(0.750)(9.80)=0.361\mu_s = \frac{F_{\text{pull}}}{mg} = \frac{2.65}{(0.750)(9.80)} = 0.361; (b) FN=mgcos⁡θ=6.81 NF_N = mg\cos\theta = 6.81\text{ N}, so fs,max⁡=μsFN=2.46 Nf_{s,\max} = \mu_s F_N = 2.46\text{ N}; (c) Parallel gravity component Fg,∥=mgsin⁡θ=2.75 NF_{g,\parallel} = mg\sin\theta = 2.75\text{ N}. Since Fg,∥>fs,max⁡F_{g,\parallel} > f_{s,\max} (2.75 N>2.46 N2.75\text{ N} > 2.46\text{ N}), the block breaks away and slides down the track; net force immediately upon breakaway is Fnet,∥=Fg,∥−fs>0F_{\text{net},\parallel} = F_{g,\parallel} - f_s > 0.

Steps

Part (a): Determine the Coefficient of Static Friction μs\mu_s

On a flat, horizontal surface (θ=0∘\theta = 0^\circ), the vertical forces acting on the block are balanced: FN=mgF_N = mg

At the exact instant of breakaway, the applied pulling force matches the maximum possible static friction force: Fpull=fs,max⁡=μsFN=μsmgF_{\text{pull}} = f_{s,\max} = \mu_s F_N = \mu_s mg

Rearranging for the coefficient of static friction μs\mu_s: μs=Fpullmg\mu_s = \frac{F_{\text{pull}}}{mg}

Substitute the given values: μs=2.65 N(0.750 kg)(9.80 m/s2)=2.657.35≈0.361\mu_s = \frac{2.65\text{ N}}{(0.750\text{ kg})(9.80\text{ m/s}^2)} = \frac{2.65}{7.35} \approx 0.361


Part (b): Component Force Balance and Maximum Static Friction on the Incline

When the track is inclined at an angle θ=22.0∘\theta = 22.0^\circ, set up a tilted coordinate system:

  • The xx-axis is parallel to the track surface, pointing down the incline.
  • The yy-axis is perpendicular to the track surface, pointing upward.
  1. Perpendicular direction (yy-axis):
    Since there is no acceleration perpendicular to the track, the normal force balances the perpendicular component of gravity: FN=mgcos⁡θF_N = mg\cos\theta FN=(0.750 kg)(9.80 m/s2)cos⁡(22.0∘)=(7.35 N)(0.9272)≈6.81 NF_N = (0.750\text{ kg})(9.80\text{ m/s}^2)\cos(22.0^\circ) = (7.35\text{ N})(0.9272) \approx 6.81\text{ N}
  2. Maximum static friction force:
    The maximum opposing force static friction can provide is proportional to this reduced normal force: fs,max⁡=μsFNf_{s,\max} = \mu_s F_N fs,max⁡=(0.3605)(6.815 N)≈2.46 Nf_{s,\max} = (0.3605)(6.815\text{ N}) \approx 2.46\text{ N}

Common Pitfall: Do not use the flat-track normal force (mgmg) when calculating friction on an incline. Tilting the track reduces the contact pressure between the surfaces by a factor of cos⁡θ\cos\theta, which lowers fs,max⁡f_{s,\max}.


Part (c): Determine Motion and Net Force Along the Incline

  1. Downhill component of gravity:
    The force pulling the block down the incline is the parallel component of gravity: Fg,∥=mgsin⁡θF_{g,\parallel} = mg\sin\theta Fg,∥=(7.35 N)sin⁡(22.0∘)=(7.35 N)(0.3746)≈2.75 NF_{g,\parallel} = (7.35\text{ N})\sin(22.0^\circ) = (7.35\text{ N})(0.3746) \approx 2.75\text{ N}
  2. Comparison with fs,max⁡f_{s,\max}:
    Compare the driving force down the track to the maximum resisting force: Fg,∥=2.75 Nandfs,max⁡=2.46 NF_{g,\parallel} = 2.75\text{ N} \quad \text{and} \quad f_{s,\max} = 2.46\text{ N} Since Fg,∥>fs,max⁡F_{g,\parallel} > f_{s,\max} (2.75 N>2.46 N2.75\text{ N} > 2.46\text{ N}), the maximum static friction cannot hold the block in equilibrium. The block breaks away and begins to slide down the incline.
  3. Net force at the instant of release:
    Taking the direction down the incline as positive: Fnet,∥=Fg,∥−fs,max⁡=2.75 N−2.46 N=0.29 NF_{\text{net},\parallel} = F_{g,\parallel} - f_{s,\max} = 2.75\text{ N} - 2.46\text{ N} = 0.29\text{ N} Because Fnet,∥>0F_{\text{net},\parallel} > 0, there is a non-zero downward net force initiating acceleration down the track.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student swaps the sine and cosine components when resolving forces on the incline, using sine for the normal force.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    N=mg=(0.750)(9.80)=7.35 N  ⟹  μs=FpullN=2.657.35=0.361N = mg = (0.750)(9.80) = 7.35\text{ N} \implies \mu_s = \frac{F_{\text{pull}}}{N} = \frac{2.65}{7.35} = 0.361

  2. Step 2

    N=mgsin⁡θ=(7.35)sin⁡(22.0∘)=2.75 N  ⟹  fs,max⁡=μsN=(0.361)(2.75)=0.993 NN = mg\sin\theta = (7.35)\sin(22.0^\circ) = 2.75\text{ N} \implies f_{s,\max} = \mu_s N = (0.361)(2.75) = 0.993\text{ N}

    Correct

    FN=mgcos⁡θ=(7.35 N)cos⁡(22.0∘)≈6.81 N  ⟹  fs,max⁡=μsFN=(0.361)(6.81 N)≈2.46 NF_N = mg\cos\theta = (7.35\text{ N})\cos(22.0^\circ) \approx 6.81\text{ N} \implies f_{s,\max} = \mu_s F_N = (0.361)(6.81\text{ N}) \approx 2.46\text{ N}

    The normal force balances the perpendicular component of gravity, which is adjacent to the angle θ\theta between the vertical and the normal axis, giving FN=mgcos⁡θF_N = mg\cos\theta rather than mgsin⁡θmg\sin\theta.

  3. Step 3

    Fparallel=mgcos⁡θ=(7.35)cos⁡(22.0∘)=6.82 N  ⟹  Fparallel>fs,max⁡, so the block begins to slide  ⟹  Fnet=6.82 N−0.993 N=5.83 N down the inclineF_{\text{parallel}} = mg\cos\theta = (7.35)\cos(22.0^\circ) = 6.82\text{ N} \implies F_{\text{parallel}} > f_{s,\max} \text{, so the block begins to slide} \implies F_{\text{net}} = 6.82\text{ N} - 0.993\text{ N} = 5.83\text{ N down the incline}

    Correct

    Fg,∥=mgsin⁡θ=(7.35 N)sin⁡(22.0∘)≈2.75 N  ⟹  Fg,∥>fs,max⁡ (2.75 N>2.46 N)  ⟹  Fnet,∥=2.75 N−2.46 N=0.29 NF_{g,\parallel} = mg\sin\theta = (7.35\text{ N})\sin(22.0^\circ) \approx 2.75\text{ N} \implies F_{g,\parallel} > f_{s,\max}\ (2.75\text{ N} > 2.46\text{ N}) \implies F_{\text{net},\parallel} = 2.75\text{ N} - 2.46\text{ N} = 0.29\text{ N}

    Your reasoning that the block slides when the downhill force exceeds fs,max⁡f_{s,\max} is logically sound, but your numerical values were affected by swapping the components of gravity.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the horizontal breakaway data to find the coefficient of static friction.

You correctly related the maximum static friction force to the normal force using fs,max⁡=μsFNf_{s,\max} = \mu_s F_N.

You applied the correct decision rule comparing the parallel driving force to fs,max⁡f_{s,\max} to determine whether sliding occurs.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric Component Swap on Incline

You swapped sine and cosine when decomposing the weight vector on the inclined plane.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You associated the perpendicular normal force with sin⁡θ\sin\theta and the parallel downhill force with cos⁡θ\cos\theta. Because the incline angle θ\theta is measured from the horizontal, the angle between the vertical gravity vector and the line perpendicular to the incline is also θ\theta. Therefore, the perpendicular component is adjacent to θ\theta (mgcos⁡θmg\cos\theta), while the parallel downhill component is opposite θ\theta (mgsin⁡θmg\sin\theta).

REASONING PATH
Your ACEpath teacher’s suggested approach
Perpendicular Component (Normal Direction)
  • For an incline tilted at angle θ\theta above horizontal, Fg,⊥=mgcos⁡θF_{g,\perp} = mg\cos\theta.

  • Check the zero-angle limit: when θ=0∘\theta = 0^\circ, cos⁡(0∘)=1\cos(0^\circ) = 1, restoring the flat-ground result FN=mgF_N = mg.

Parallel Component (Downhill Direction)
  • The downhill pulling component of gravity along the incline is Fg,∥=mgsin⁡θF_{g,\parallel} = mg\sin\theta.

  • Check the zero-angle limit: when θ=0∘\theta = 0^\circ, sin⁡(0∘)=0\sin(0^\circ) = 0, meaning gravity exerts no downhill pulling force on a flat surface.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the perpendicular component of gravity to find the normal force: FN=mgcos⁡(22.0∘)=(0.750 kg)(9.80 m/s2)cos⁡(22.0∘)≈6.81 NF_N = mg\cos(22.0^\circ) = (0.750\text{ kg})(9.80\text{ m/s}^2)\cos(22.0^\circ) \approx 6.81\text{ N}.

  2. Calculate the maximum static friction force: fs,max⁡=μsFN=(0.361)(6.81 N)≈2.46 Nf_{s,\max} = \mu_s F_N = (0.361)(6.81\text{ N}) \approx 2.46\text{ N}.

  3. Compute the parallel driving component of gravity: Fg,∥=mgsin⁡(22.0∘)=(7.35 N)sin⁡(22.0∘)≈2.75 NF_{g,\parallel} = mg\sin(22.0^\circ) = (7.35\text{ N})\sin(22.0^\circ) \approx 2.75\text{ N}.

  4. Compare forces and find the net force at release: since Fg,∥=2.75 N>fs,max⁡=2.46 NF_{g,\parallel} = 2.75\text{ N} > f_{s,\max} = 2.46\text{ N}, the block slides, and Fnet,∥=2.75 N−2.46 N=0.29 NF_{\text{net},\parallel} = 2.75\text{ N} - 2.46\text{ N} = 0.29\text{ N} down the track.

Final answer

(a) μs≈0.361\mu_s \approx 0.361; (b) FN≈6.81 NF_N \approx 6.81\text{ N}, fs,max⁡≈2.46 Nf_{s,\max} \approx 2.46\text{ N}; (c) The block slides; Fnet≈0.29 NF_{\text{net}} \approx 0.29\text{ N} down the incline.

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch a right triangle decomposing the downward weight vector mg⃗m\vec{g} into components perpendicular and parallel to the ramp.

  • Label the incline angle θ\theta at the top vertex of the weight decomposition triangle to clearly see which side is adjacent and which side is opposite.

  • Test your trigonometric choices using limiting cases: verify that the downhill force vanishes when θ→0∘\theta \to 0^\circ and equals full weight when θ→90∘\theta \to 90^\circ.

OverviewACEpath Teacher's Diagnosis

02 The student uses the horizontal normal force N = mg instead of accounting for the incline angle when computing the maximum static friction.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    N=mg=(0.750)(9.80)=7.35 N  ⟹  μs=2.657.35=0.361N = mg = (0.750)(9.80) = 7.35\text{ N} \implies \mu_s = \frac{2.65}{7.35} = 0.361

  2. Step 2

    N=mg=7.35 N  ⟹  fs,max⁡=μsN=(0.361)(7.35)=2.65 NN = mg = 7.35\text{ N} \implies f_{s,\max} = \mu_s N = (0.361)(7.35) = 2.65\text{ N}

    Correct

    FN=mgcos⁡(22.0∘)=(7.35 N)(0.9272)≈6.81 N  ⟹  fs,max⁡=μsFN=(0.361)(6.81 N)≈2.46 NF_N = mg\cos(22.0^\circ) = (7.35\text{ N})(0.9272) \approx 6.81\text{ N} \implies f_{s,\max} = \mu_s F_N = (0.361)(6.81\text{ N}) \approx 2.46\text{ N}

    On an inclined plane, the surface supports only the perpendicular component of gravity, so FN=mgcos⁡θF_N = mg\cos\theta. Using FN=mgF_N = mg neglects the tilt angle and overestimates fs,max⁡f_{s,\max}.

  3. Step 3

    Fg,parallel=mgsin⁡(22.0∘)=(7.35)(0.3746)=2.75 N  ⟹  Fg,parallel>fs,max⁡, so the block begins to slideF_{g,\text{parallel}} = mg\sin(22.0^\circ) = (7.35)(0.3746) = 2.75\text{ N} \implies F_{g,\text{parallel}} > f_{s,\max}\text{, so the block begins to slide}

  4. Step 4

    Fnet=2.75 N−2.65 N=0.10 N down the inclineF_{\text{net}} = 2.75\text{ N} - 2.65\text{ N} = 0.10\text{ N} \text{ down the incline}

    Correct

    Fnet,∥=Fg,∥−fs,max⁡=2.75 N−2.46 N=0.29 N down the inclineF_{\text{net},\parallel} = F_{g,\parallel} - f_{s,\max} = 2.75\text{ N} - 2.46\text{ N} = 0.29\text{ N} \text{ down the incline}

    Your subtraction method is correct, but the numerical result is affected by your earlier calculation of fs,max⁡f_{s,\max}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the horizontal breakaway data to find the static friction coefficient μs\mu_s.

You correctly resolved the component of gravity acting parallel to the incline as mgsin⁡θmg\sin\theta.

You correctly set up the condition for breakaway by comparing the driving force to the maximum available static friction.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Normal Force Component Misidentification on Incline

You reused the flat-surface normal force N=mgN = mg when analyzing the inclined surface instead of resolving gravity perpendicular to the track.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating FN=mgF_N = mg as a universal definition rather than deriving FNF_N from Newton's second law along the tilted perpendicular axis (ΣF⊥=FN−mgcos⁡θ=0\Sigma F_\perp = F_N - mg\cos\theta = 0).

REASONING PATH
Your ACEpath teacher’s suggested approach
Perpendicular Equilibrium
  • For a surface tilted at angle θ\theta with no perpendicular acceleration, ΣF⊥=FN−mgcos⁡θ=0  ⟹  FN=mgcos⁡θ\Sigma F_\perp = F_N - mg\cos\theta = 0 \implies F_N = mg\cos\theta.

  • Always tilt your coordinate axes along and perpendicular to the ramp before writing force balance equations.

Angle Dependence of Normal Force
  • As tilt angle θ\theta increases from 0∘0^\circ to 90∘90^\circ, cos⁡θ\cos\theta decreases, reducing contact pressure and maximum static friction.

  • Check your normal force: on an incline with no other perpendicular forces, FNF_N must be strictly less than mgmg.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the perpendicular force balance: FN=mgcos⁡(22.0∘)=(7.35 N)(0.9272)=6.81 NF_N = mg\cos(22.0^\circ) = (7.35\text{ N})(0.9272) = 6.81\text{ N}.

  2. Calculate maximum static friction on the incline: fs,max⁡=μsFN=(0.361)(6.81 N)=2.46 Nf_{s,\max} = \mu_s F_N = (0.361)(6.81\text{ N}) = 2.46\text{ N}.

  3. Calculate the net force down the incline at release: Fnet=Fg,∥−fs,max⁡=2.75 N−2.46 N=0.29 NF_{\text{net}} = F_{g,\parallel} - f_{s,\max} = 2.75\text{ N} - 2.46\text{ N} = 0.29\text{ N} down the track.

Final answer

(a) μs=0.361\mu_s = 0.361; (b) FN=6.81 NF_N = 6.81\text{ N}, fs,max⁡=2.46 Nf_{s,\max} = 2.46\text{ N}; (c) The block begins to slide; Fnet=0.29 NF_{\text{net}} = 0.29\text{ N} down the incline.

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice drawing tilted free-body diagrams where gravity is split into mgsin⁡θmg\sin\theta down the ramp and mgcos⁡θmg\cos\theta into the ramp.

  • Verify limiting cases: at θ=0∘\theta = 0^\circ, cos⁡(0∘)=1  ⟹  FN=mg\cos(0^\circ)=1 \implies F_N = mg; at θ=90∘\theta = 90^\circ, cos⁡(90∘)=0  ⟹  FN=0\cos(90^\circ)=0 \implies F_N = 0.

OverviewACEpath Teacher's Diagnosis

03 The student assumes static friction always opposes the full downhill component of gravity regardless of whether the threshold f_s,max is exceeded, concluding the block stays at rest with zero net force.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    N=mg=(0.750)(9.80)=7.35 N  ⟹  μs=2.657.35=0.361N = mg = (0.750)(9.80) = 7.35\text{ N} \implies \mu_s = \frac{2.65}{7.35} = 0.361

  2. Step 2

    N=mgcos⁡(22.0∘)=(7.35)(0.9272)=6.82 N  ⟹  fs,max⁡=μsN=(0.361)(6.82)=2.46 NN = mg\cos(22.0^\circ) = (7.35)(0.9272) = 6.82\text{ N} \implies f_{s,\max} = \mu_s N = (0.361)(6.82) = 2.46\text{ N}

  3. Step 3

    Fg,parallel=mgsin⁡(22.0∘)=2.75 N  ⟹  fs=Fg,parallel=2.75 N to balance gravityF_{g,\text{parallel}} = mg\sin(22.0^\circ) = 2.75\text{ N} \implies f_s = F_{g,\text{parallel}} = 2.75\text{ N}\text{ to balance gravity}

    Correct

    Fg,∥=mgsin⁡(22.0∘)≈2.75 NF_{g,\parallel} = mg\sin(22.0^\circ) \approx 2.75\text{ N}. Since Fg,∥=2.75 N>fs,max⁡=2.46 NF_{g,\parallel} = 2.75\text{ N} > f_{s,\max} = 2.46\text{ N}, static friction cannot reach 2.75 N2.75\text{ N}.

    Static friction can only supply up to fs,max⁡=2.46 Nf_{s,\max} = 2.46\text{ N}. Because the downhill component of gravity (2.75 N2.75\text{ N}) exceeds this limit, static friction cannot balance gravity.

  4. Step 4

    The block remains at rest  ⟹  Fnet=0 N\text{The block remains at rest} \implies F_{\text{net}} = 0\text{ N}

    Correct

    The block begins to slide down the track, and Fnet,∥=Fg,∥−fs,max⁡=2.75 N−2.46 N=0.29 NF_{\text{net},\parallel} = F_{g,\parallel} - f_{s,\max} = 2.75\text{ N} - 2.46\text{ N} = 0.29\text{ N} down the incline.

    Because you assumed static friction balanced the downhill pull, you concluded the block remained at rest instead of identifying that it breaks away with a net downward force.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly balanced forces on the horizontal plane to find the coefficient of static friction.

You correctly identified that the normal force decreases to mgcos⁡θmg\cos\theta on an incline.

You accurately calculated the downhill driving component of gravity as mgsin⁡θmg\sin\theta.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Static Friction Threshold Neglected

You set static friction equal to the parallel gravity component without comparing it against the maximum limit you calculated in part (b).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Static friction is a self-adjusting reaction force, but it has a hard upper limit (fs≤μsFNf_s \le \mu_s F_N). When an applied driving force exceeds fs,max⁡f_{s,\max}, static equilibrium breaks down, the surfaces slip, and static friction can no longer balance the load.

REASONING PATH
Your ACEpath teacher’s suggested approach
Static Friction Condition
  • fs≤fs,max⁡=μsFNf_s \le f_{s,\max} = \mu_s F_N

  • Always evaluate whether the driving force is less than, equal to, or greater than fs,max⁡f_{s,\max} before assuming equilibrium.

Breakaway Test
  • If Fdrive>fs,max⁡F_{\text{drive}} > f_{s,\max}, motion initiates and Fnet=Fdrive−fs,max⁡>0F_{\text{net}} = F_{\text{drive}} - f_{s,\max} > 0.

  • Compare Fg,∥F_{g,\parallel} directly against fs,max⁡f_{s,\max} to decide whether the block stays at rest or slides.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compare the driving force to the maximum holding force: 2.75 N>2.46 N2.75\text{ N} > 2.46\text{ N}.

  2. Conclude that static friction is exceeded, so the block begins to slide down the track.

  3. Calculate the net force along the incline at the instant of release: Fnet,∥=Fg,∥−fs,max⁡=2.75 N−2.46 N=0.29 NF_{\text{net},\parallel} = F_{g,\parallel} - f_{s,\max} = 2.75\text{ N} - 2.46\text{ N} = 0.29\text{ N} down the track.

Final answer

The block begins to slide down the incline, and the net force at release is 0.29 N0.29\text{ N} directed down the track.

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice explicitly writing the inequality Fdrive≤fs,max⁡F_{\text{drive}} \le f_{s,\max} before writing any equilibrium equation involving static friction.

  • Review the transition between static and kinetic friction when breakaway occurs.

Lock it in

Similar question

01

A 1.50 kg1.50\text{ kg} wooden crate rests on a ramp inclined at 18.0∘18.0^\circ to the horizontal. Take g=9.80 m/s2g = 9.80\text{ m/s}^2. Calculate: (a) the normal force exerted by the ramp on the crate, and (b) the component of gravity acting parallel to the ramp.

Answer

(a) FN=mgcos⁡(18.0∘)=(1.50)(9.80)cos⁡(18.0∘)=14.7cos⁡(18.0∘)≈13.98 N≈14.0 NF_N = mg\cos(18.0^\circ) = (1.50)(9.80)\cos(18.0^\circ) = 14.7\cos(18.0^\circ) \approx 13.98\text{ N} \approx 14.0\text{ N}. (b) Fg,∥=mgsin⁡(18.0∘)=14.7sin⁡(18.0∘)≈4.54 NF_{g,\parallel} = mg\sin(18.0^\circ) = 14.7\sin(18.0^\circ) \approx 4.54\text{ N}.

02

A 2.40 kg2.40\text{ kg} block is placed on an incline tilted at 25.0∘25.0^\circ above the horizontal. The coefficient of static friction is μs=0.520\mu_s = 0.520. Take g=9.80 m/s2g = 9.80\text{ m/s}^2. Determine whether the block will remain at rest or slide down the incline.

Answer

Normal force: FN=mgcos⁡(25.0∘)=(2.40)(9.80)cos⁡(25.0∘)≈21.32 NF_N = mg\cos(25.0^\circ) = (2.40)(9.80)\cos(25.0^\circ) \approx 21.32\text{ N}. Maximum static friction: fs,max⁡=μsFN=(0.520)(21.32 N)≈11.09 Nf_{s,\max} = \mu_s F_N = (0.520)(21.32\text{ N}) \approx 11.09\text{ N}. Driving force down incline: Fg,∥=mgsin⁡(25.0∘)=(2.40)(9.80)sin⁡(25.0∘)≈9.94 NF_{g,\parallel} = mg\sin(25.0^\circ) = (2.40)(9.80)\sin(25.0^\circ) \approx 9.94\text{ N}. Since Fg,∥<fs,max⁡F_{g,\parallel} < f_{s,\max} (9.94 N<11.09 N9.94\text{ N} < 11.09\text{ N}), the block remains at rest.

03

An aluminum block rests on an adjustable incline. By slowly increasing the tilt angle, it is observed that the block begins to slip at an angle of θc=31.0∘\theta_c = 31.0^\circ. (a) Derive an expression for the coefficient of static friction μs\mu_s strictly in terms of θc\theta_c. (b) Calculate the numerical value of μs\mu_s.

Answer

(a) At critical impending slip, Fg,∥=fs,max⁡  ⟹  mgsin⁡θc=μs(mgcos⁡θc)  ⟹  μs=sin⁡θccos⁡θc=tan⁡θcF_{g,\parallel} = f_{s,\max} \implies mg\sin\theta_c = \mu_s (mg\cos\theta_c) \implies \mu_s = \frac{\sin\theta_c}{\cos\theta_c} = \tan\theta_c. (b) μs=tan⁡(31.0∘)≈0.601\mu_s = \tan(31.0^\circ) \approx 0.601.

Loading workspace…