Resources
A uniform steel rod of length and mass is hinged horizontally at its left end to a vertical wall and supported at its right end by a vertical cable. A movable slider of mass rests on the rod. The cable can withstand a maximum tensile force of before snapping. Taking the acceleration due to gravity to be , calculate the maximum distance from the hinge that the slider can be placed without causing the cable to snap.
Answer and steps
Final answer
Steps
Identify the Pivot and Forces
To find the maximum distance without snapping the cable, consider the rotational equilibrium of the system just before the cable reaches its maximum allowed tension, .
Choose the hinge at the left end () as the pivot point. This eliminates the unknown reaction forces from the wall because their lever arm is zero.
The forces exerting torque about the pivot are:
- Cable tension (): Acts vertically upward at the right end (), producing a counterclockwise torque.
- Weight of the uniform rod (): Acts downward at its center of mass (), producing a clockwise torque.
- Weight of the slider (): Acts downward at distance from the hinge, producing a clockwise torque.
Set Up the Torque Equilibrium Equation
For the rod to remain in static equilibrium:
Equating the counterclockwise torque to the clockwise torques:
Calculate the Known Torques
- Maximum counterclockwise torque from the cable:
- Clockwise torque due to the rod's own weight:
- Allowable torque for the slider: Subtract the rod's torque from the cable's maximum torque:
Solve for the Maximum Distance
The torque exerted by the slider is . Using the slider load of (the nominal weight corresponding to the mass):
Placing the slider beyond increases the clockwise torque, demanding a tension greater than and causing the cable to snap.
Typical errors
01 The student misidentifies the center of gravity of the uniform rod, taking its lever arm about the hinge as L rather than L/2.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Because the rod is uniform, its gravitational force acts at its center of mass, which is located at its midpoint from the hinge pivot, not at the end .
- Step 2Correct
You substituted your values and collected terms accurately based on your torque equation, but the rod's torque term was doubled because of the incorrect lever arm.
- Step 3Correct
Your final division correctly followed from your previous linear equation, but the numerical result is smaller than the true maximum allowable distance.
WHAT YOU DID WELL
Compliments from Your TeacherYou chose the hinge as the pivot point to eliminate the unknown wall reaction forces.
You assigned the correct rotational signs to each torque, with upward cable tension opposing the downward gravitational forces.
You carried out your arithmetic and algebraic rearrangement accurately.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou assigned the full length as the moment arm for the rod's weight rather than placing it at the midpoint.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the total length of an extended body with the position of its center of gravity when calculating the gravitational torque of a uniform object.
REASONING PATH
Your ACEpath teacher’s suggested approach- Locate Center of Gravity First
For any uniform extended body in a uniform gravitational field, gravity acts at its geometric center.
Before writing the torque expression for a uniform bar of length pivoted at one end, immediately sketch the weight vector at .
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up rotational equilibrium about the hinge with the rod's weight at its center of mass:
Calculate the maximum allowable torque for the slider:
Solve for the maximum placement distance:
02 The student forgets to include the gravitational torque exerted by the rod itself in the rotational equilibrium condition.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You set up the rotational equilibrium equation but omitted the clockwise torque produced by the uniform rod's own weight, .
- Step 2Correct
You substituted the numerical values into your torque equation correctly, but the resulting expression inherited the missing rod-weight term.
- Step 3Correct
Your final division correctly evaluated your algebraic expression, but because the rod's torque was omitted earlier, the calculated distance is too large.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly chose the hinge as the pivot point to eliminate wall reaction forces.
You correctly identified the torque arm and maximum tension for the supporting cable.
You accurately carried out the arithmetic and algebraic isolation for your formulated equation.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the rod as a massless beam rather than accounting for the downward gravitational force acting at the center of mass of a massive uniform rod.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check for Body Weight
Every massive object in static equilibrium experiences gravity at its center of mass ( at for a uniform beam).
Always draw a free-body diagram showing the beam's weight vector before writing the torque sum.
- Torque Budgeting
Counterclockwise torque must balance all clockwise torques combined: .
Deduct the beam's own torque contribution from the maximum support torque before solving for the unknown load position.
CORRECTED PATH
ACEpath Teacher's DemonstrationInclude the rod's weight acting at its midpoint: .
Find the remaining torque available for the slider: .
Solve for the maximum placement distance: .
03 The student uses masses directly instead of weights in the torque equation while using the maximum force in newtons.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You used the masses and directly as forces. Because torque requires force (), gravitational loads must be entered as weights ( in newtons) rather than masses in kilograms.
- Step 2Correct
Your algebraic rearrangement was executed correctly, but the numerical coefficients were carried over from the incorrect mass substitution in Step 1.
- Step 3Correct
Your division arithmetic is correct based on your prior equation, but the resulting value is incorrect due to the initial mass-versus-weight substitution error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly selected the hinge as the pivot point to eliminate unknown hinge reaction forces.
You correctly identified that the cable exerts a counterclockwise torque while the rod and slider exert clockwise torques.
You correctly recognized that the rod's weight acts at its center of mass, halfway along the beam ().
You correctly solved your linear equation algebraically.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted mass values in kilograms directly into the torque balance equation alongside a force in newtons.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTorque is defined as the product of force and perpendicular distance (). When an object's mass is given in kilograms, gravity produces a downward force equal to its weight ( in newtons). Substituting mass alone ignores the factor of , making the terms dimensionally inconsistent with the tension force given in newtons.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Dimensional Consistency
Every term in a torque sum must have dimensions of torque ().
Ensure that every mass is multiplied by so that you are summing force times distance, not mass times distance.
- Perform a Physical Sanity Check
A load resting on a finite beam must have a position that falls within the physical boundaries of the beam ().
Compare your calculated distance to the rod length . Finding that immediately alerts you to check unit conversions or missing factors of .
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the gravitational loads into downward forces in newtons: the rod's weight is , acting at .
Set up the torque equilibrium equation about the hinge: .
Substitute the known values: .
Simplify the torque values: .
Lock it in
Where does the equivalent gravitational force act on a uniform beam of length ?
At its geometric center (center of mass), exactly from either end.
Similar question
A uniform wooden plank of length and mass is hinged at one end and held horizontal by a vertical wire at the opposite end. Taking , find the tension in the wire when no additional load is present.
Answer
. Key step: Balance torques about the hinge: .
A horizontal uniform beam of length and mass is supported by a hinge at the left end and a vertical cable at the right end. A worker of mass stands from the hinge. Taking , calculate the tension in the cable.
Answer
. Key step: .
A uniform steel bar of length and mass is hinged at its left end. A vertical support wire is attached at a distance of from the hinge and can sustain a maximum tension of . Taking , find the maximum mass of a box that can be placed at the rightmost tip () without breaking the wire.
Answer
. Key step: Torque balance about the hinge gives . Substituting values: .