Resources

A two-pulley belt-drive system consists of a drive pulley of radius r1=6.00 cmr_1 = 6.00\text{ cm} coupled via a taut, non-slipping timing belt to a driven pulley of radius r2=18.0 cmr_2 = 18.0\text{ cm}. The drive pulley rotates at an angular speed of ω1=150 rad/s\omega_1 = 150\text{ rad/s}. (a) Determine the linear speed vbeltv_{\text{belt}} of the timing belt. (b) Determine the resulting angular speed ω2\omega_2 of the driven pulley. (c) If a dust speck rests on the rim of the driven pulley, compute the magnitude of its centripetal acceleration aca_c. Round all results to three significant figures.

Answer and steps

Final answer

(a) vbelt=9.00 m/sv_{\text{belt}} = 9.00\text{ m/s}; (b) ω2=50.0 rad/s\omega_2 = 50.0\text{ rad/s}; (c) ac=450 m/s2a_c = 450\text{ m/s}^2

Steps

Part (a): Linear Speed of the Belt

When a belt moves around a rotating pulley without slipping, every point on the belt moves at the same tangential linear speed as the outer rim of the pulley.

First, convert the radius of the drive pulley into standard SI units: r1=6.00 cm=0.0600 mr_1 = 6.00\text{ cm} = 0.0600\text{ m}

The relationship between tangential linear speed vv and angular speed ω\omega is: v=rωv = r\omega

Substitute the drive pulley's values to find the speed of the belt vbeltv_{\text{belt}}: vbelt=r1ω1=(0.0600 m)(150 rad/s)=9.00 m/sv_{\text{belt}} = r_1 \omega_1 = (0.0600\text{ m})(150\text{ rad/s}) = 9.00\text{ m/s}


Part (b): Angular Speed of the Driven Pulley

Because the timing belt is non-slipping and taut, the tangential speed at the rim of the driven pulley v2v_2 must match the belt speed: v2=vbelt=9.00 m/sv_2 = v_{\text{belt}} = 9.00\text{ m/s}

Convert the radius of the driven pulley into meters: r2=18.0 cm=0.180 mr_2 = 18.0\text{ cm} = 0.180\text{ m}

Rearranging v2=r2ω2v_2 = r_2 \omega_2 gives: ω2=v2r2=9.00 m/s0.180 m=50.0 rad/s\omega_2 = \frac{v_2}{r_2} = \frac{9.00\text{ m/s}}{0.180\text{ m}} = 50.0\text{ rad/s}

Common Pitfall: Do not confuse angular speed ω\omega with linear speed vv. While both pulleys share the identical rim linear speed (v1=v2=vbeltv_1 = v_2 = v_{\text{belt}}), the larger pulley rotates through fewer radians per second (ω2<ω1\omega_2 < \omega_1) because its circumference is larger.


Part (c): Centripetal Acceleration of the Dust Speck

A point on the outer rim of the driven pulley experiences centripetal acceleration directed toward the center of rotation: ac=v2r=rω2a_c = \frac{v^2}{r} = r\omega^2

Using v2=9.00 m/sv_2 = 9.00\text{ m/s} and r2=0.180 mr_2 = 0.180\text{ m}: ac=v22r2=(9.00 m/s)20.180 m=81.0 m2/s20.180 m=450 m/s2a_c = \frac{v_2^2}{r_2} = \frac{(9.00\text{ m/s})^2}{0.180\text{ m}} = \frac{81.0\text{ m}^2/\text{s}^2}{0.180\text{ m}} = 450\text{ m/s}^2

(Alternative check using angular speed: ac=r2ω22=(0.180 m)(50.0 rad/s)2=450 m/s2a_c = r_2 \omega_2^2 = (0.180\text{ m})(50.0\text{ rad/s})^2 = 450\text{ m/s}^2.)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert the radius from centimeters to meters when computing linear speed, causing all subsequent linear quantities to be off by a factor of 100.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    vbelt=r1⋅ω1  ⟹  vbelt=6.00⋅150=900 m/sv_{\text{belt}} = r_1 \cdot \omega_1 \implies v_{\text{belt}} = 6.00 \cdot 150 = 900\text{ m/s}

    Correct

    vbelt=r1ω1=(0.0600 m)(150 rad/s)=9.00 m/sv_{\text{belt}} = r_1 \omega_1 = (0.0600\text{ m})(150\text{ rad/s}) = 9.00\text{ m/s}

    You correctly selected the formula v=rωv = r\omega, but you used r1=6.00 cmr_1 = 6.00\text{ cm} without converting it to meters (0.0600 m0.0600\text{ m}), leading to a speed that is 100 times too large in meters per second.

  2. Step 2

    ω2=vbeltr2  ⟹  ω2=90018.0=50.0 rad/s\omega_2 = \frac{v_{\text{belt}}}{r_2} \implies \omega_2 = \frac{900}{18.0} = 50.0\text{ rad/s}

  3. Step 3

    ac=vbelt2r2  ⟹  ac=900218.0=45000 m/s2a_c = \frac{v_{\text{belt}}^2}{r_2} \implies a_c = \frac{900^2}{18.0} = 45000\text{ m/s}^2

    Correct

    ac=vbelt2r2=(9.00 m/s)20.180 m=450 m/s2a_c = \frac{v_{\text{belt}}^2}{r_2} = \frac{(9.00\text{ m/s})^2}{0.180\text{ m}} = 450\text{ m/s}^2

    You used the correct centripetal acceleration formula, but substituting linear values in centimeters while labeling the final unit as m/s2\text{m/s}^2 caused your answer to be off by a factor of 100.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the linear-to-rotational relation v=rωv = r\omega for a non-slipping belt system.

You recognized that the linear speed at the rim of both pulleys is equal to the belt speed.

You selected the appropriate formula ac=v2ra_c = \frac{v^2}{r} for centripetal acceleration.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion

You forgot to convert the pulley radii from centimeters to meters before carrying out the arithmetic.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking base unit consistency in rotational formulas causes linear quantities like tangential velocity and centripetal acceleration to carry hidden centimeter scaling into standard SI unit labels.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check SI Base Units
  • Standard rotational formulas (v=rωv = r\omega, ac=rω2a_c = r\omega^2) yield SI units (m/s\text{m/s}, m/s2\text{m/s}^2) only when radius rr is in meters.

  • Always convert centimeters to meters by dividing by 100 before substituting into linear-rotational formulas.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert radii to meters: r1=0.0600 mr_1 = 0.0600\text{ m} and r2=0.180 mr_2 = 0.180\text{ m}.

  2. Recalculate belt speed: vbelt=r1ω1=(0.0600 m)(150 rad/s)=9.00 m/sv_{\text{belt}} = r_1 \omega_1 = (0.0600\text{ m})(150\text{ rad/s}) = 9.00\text{ m/s}.

  3. Recompute centripetal acceleration: ac=vbelt2r2=(9.00 m/s)20.180 m=450 m/s2a_c = \frac{v_{\text{belt}}^2}{r_2} = \frac{(9.00\text{ m/s})^2}{0.180\text{ m}} = 450\text{ m/s}^2.

Final answer

(a) vbelt=9.00 m/sv_{\text{belt}} = 9.00\text{ m/s}; (b) ω2=50.0 rad/s\omega_2 = 50.0\text{ rad/s}; (c) ac=450 m/s2a_c = 450\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Write explicit unit labels inside your substitution lines to catch mismatched units early.

  • Verify that linear acceleration units match: if radius is in centimeters, acceleration results in cm/s2\text{cm/s}^2, which requires division by 100 to yield m/s2\text{m/s}^2.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the radius ratio by assuming angular speed is directly proportional to radius rather than inversely proportional, resulting in an angular speed of 450 rad/s.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    vbelt=r1⋅ω1  ⟹  vbelt=0.0600⋅150=9.00 m/sv_{\text{belt}} = r_1 \cdot \omega_1 \implies v_{\text{belt}} = 0.0600 \cdot 150 = 9.00\text{ m/s}

  2. Step 2

    ω2=ω1⋅(r2r1)  ⟹  ω2=150⋅(18.06.00)=450 rad/s\omega_2 = \omega_1 \cdot \left(\frac{r_2}{r_1}\right) \implies \omega_2 = 150 \cdot \left(\frac{18.0}{6.00}\right) = 450\text{ rad/s}

    Correct

    ω2=ω1⋅(r1r2)=150⋅(6.0018.0)=50.0 rad/s\omega_2 = \omega_1 \cdot \left(\frac{r_1}{r_2}\right) = 150 \cdot \left(\frac{6.00}{18.0}\right) = 50.0\text{ rad/s}

    Because the belt does not slip, both rims share the same linear speed (r1ω1=r2ω2r_1 \omega_1 = r_2 \omega_2). Dividing by r2r_2 gives ω2=ω1(r1r2)\omega_2 = \omega_1 \left(\frac{r_1}{r_2}\right), so angular speed is inversely proportional to radius. A larger pulley must rotate slower than a smaller pulley.

  3. Step 3

    ac=r2⋅ω22  ⟹  ac=0.180⋅4502=36500 m/s2a_c = r_2 \cdot \omega_2^2 \implies a_c = 0.180 \cdot 450^2 = 36500\text{ m/s}^2

    Correct

    ac=r2ω22=(0.180 m)(50.0 rad/s)2=450 m/s2a_c = r_2 \omega_2^2 = (0.180\text{ m})(50.0\text{ rad/s})^2 = 450\text{ m/s}^2

    You applied the correct centripetal acceleration formula ac=rω2a_c = r\omega^2, but your result was affected by the incorrect value of ω2\omega_2 from part (b).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related tangential speed and angular speed using v=rωv = r\omega.

You converted centimeters to meters accurately before multiplying.

You chose the valid centripetal acceleration formula ac=rω2a_c = r\omega^2.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted proportionality ratio

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that angular velocity scales directly with pulley radius rather than inversely when tangential rim speeds are equal.

REASONING PATH
Your ACEpath teacher’s suggested approach
Equal Rim Speed Principle
  • For non-slipping belts or gears in contact, linear tangential speed is constant: v1=v2=vbeltv_1 = v_2 = v_{\text{belt}}.

  • Always begin with r1ω1=r2ω2r_1 \omega_1 = r_2 \omega_2 rather than jumping to a memorized ratio.

Sanity Check on Rotation Rate
  • Because circumference is proportional to radius (C=2πrC = 2\pi r), a larger wheel covers more distance per turn and must complete fewer turns per second.

  • Check that ωlarge<ωsmall\omega_{\text{large}} < \omega_{\text{small}} whenever two wheels share the same belt or contact surface.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Equate the tangential rim speeds: r2ω2=vbelt=9.00 m/sr_2 \omega_2 = v_{\text{belt}} = 9.00\text{ m/s}.

  2. Solve for ω2\omega_2: ω2=vbeltr2=9.00 m/s0.180 m=50.0 rad/s\omega_2 = \frac{v_{\text{belt}}}{r_2} = \frac{9.00\text{ m/s}}{0.180\text{ m}} = 50.0\text{ rad/s}.

  3. Substitute ω2=50.0 rad/s\omega_2 = 50.0\text{ rad/s} into the centripetal acceleration formula: ac=r2ω22=(0.180 m)(50.0 rad/s)2=450 m/s2a_c = r_2 \omega_2^2 = (0.180\text{ m})(50.0\text{ rad/s})^2 = 450\text{ m/s}^2.

Final answer

(a) vbelt=9.00 m/sv_{\text{belt}} = 9.00\text{ m/s}; (b) ω2=50.0 rad/s\omega_2 = 50.0\text{ rad/s}; (c) ac=450 m/s2a_c = 450\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the relationship between linear speed and angular speed for connected rotating bodies.

  • Practice deriving ratios from fundamental conservation statements like v1=v2v_1 = v_2 instead of writing ratios directly.

  • Perform a physical intuition check: verify whether a larger wheel should spin faster or slower.

OverviewACEpath Teacher's Diagnosis

03 The student misremembers the centripetal acceleration formula as linear velocity divided by radius instead of velocity squared divided by radius, yielding 50.0 m/s².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    vbelt=r1⋅ω1  ⟹  vbelt=0.0600⋅150=9.00 m/sv_{\text{belt}} = r_1 \cdot \omega_1 \implies v_{\text{belt}} = 0.0600 \cdot 150 = 9.00\text{ m/s}

  2. Step 2

    ω2=vbeltr2  ⟹  ω2=9.000.180=50.0 rad/s\omega_2 = \frac{v_{\text{belt}}}{r_2} \implies \omega_2 = \frac{9.00}{0.180} = 50.0\text{ rad/s}

  3. Step 3

    ac=vbeltr2  ⟹  ac=9.000.180=50.0 m/s2a_c = \frac{v_{\text{belt}}}{r_2} \implies a_c = \frac{9.00}{0.180} = 50.0\text{ m/s}^2

    Correct

    ac=v22r2=(9.00 m/s)20.180 m=450 m/s2a_c = \frac{v_2^2}{r_2} = \frac{(9.00\text{ m/s})^2}{0.180\text{ m}} = 450\text{ m/s}^2

    You wrote ac=vra_c = \frac{v}{r} instead of ac=v2ra_c = \frac{v^2}{r}. The expression vr\frac{v}{r} computes angular speed ω\omega (with units of s−1\text{s}^{-1} or rad/s\text{rad/s}), not linear acceleration.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the given centimeters to SI meters for both pulley radii.

You related linear speed and angular speed properly across the non-slipping belt drive.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Recall Error (Centripetal Acceleration)

You accidentally dropped the power of two on linear velocity, evaluating v/rv/r instead of v2/rv^2/r.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the formula for centripetal acceleration (ac=v2/ra_c = v^2/r) with the formula for angular speed (ω=v/r\omega = v/r), leading to an expression with the wrong physical dimensions.

REASONING PATH
Your ACEpath teacher’s suggested approach
Centripetal Acceleration Formulas
  • For circular motion at speed vv and radius rr, centripetal acceleration is ac=v2r=rω2a_c = \frac{v^2}{r} = r\omega^2.

  • Always square the linear speed when dividing by radius, or square the angular speed when multiplying by radius.

Dimensional Verification
  • Acceleration must have dimensions of length per time squared (m/s2\text{m/s}^2).

  • Check your units: vr=m/sm=s−1\frac{v}{r} = \frac{\text{m/s}}{\text{m}} = \text{s}^{-1} (frequency or angular speed), whereas v2r=m2/s2m=m/s2\frac{v^2}{r} = \frac{\text{m}^2/\text{s}^2}{\text{m}} = \text{m/s}^2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recall the centripetal acceleration formula: ac=v22r2a_c = \frac{v_2^2}{r_2} or ac=r2ω22a_c = r_2 \omega_2^2.

  2. Substitute v2=9.00 m/sv_2 = 9.00\text{ m/s} and r2=0.180 mr_2 = 0.180\text{ m}: ac=(9.00 m/s)20.180 m=81.0 m2/s20.180 ma_c = \frac{(9.00\text{ m/s})^2}{0.180\text{ m}} = \frac{81.0\text{ m}^2/\text{s}^2}{0.180\text{ m}}.

  3. Calculate the quotient: ac=450 m/s2a_c = 450\text{ m/s}^2.

Final answer

(a) vbelt=9.00 m/sv_{\text{belt}} = 9.00\text{ m/s}; (b) ω2=50.0 rad/s\omega_2 = 50.0\text{ rad/s}; (c) ac=450 m/s2a_c = 450\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Commit both standard forms of centripetal acceleration to memory: ac=v2ra_c = \frac{v^2}{r} and ac=rω2a_c = r\omega^2.

  • Perform a quick dimensional analysis on kinematic formulas whenever you write them down.

Lock it in

Similar question

01

A bicycle wheel of radius r=35.0 cmr = 35.0\text{ cm} rotates at an angular speed of ω=12.0 rad/s\omega = 12.0\text{ rad/s}. Calculate the linear speed of a point on the tire tread in meters per second.

Answer

v=4.20 m/sv = 4.20\text{ m/s}. Convert r=35.0 cm=0.350 mr = 35.0\text{ cm} = 0.350\text{ m}, then calculate v=rω=(0.350 m)(12.0 rad/s)=4.20 m/sv = r\omega = (0.350\text{ m})(12.0\text{ rad/s}) = 4.20\text{ m/s}.

02

Two gears mesh together without slipping. Gear A has a radius of 4.00 cm4.00\text{ cm} and rotates at 60.0 rad/s60.0\text{ rad/s}. Gear B has a radius of 16.0 cm16.0\text{ cm}. Find (a) the linear contact speed in m/s\text{m/s} and (b) the angular speed of Gear B in rad/s\text{rad/s}.

Answer

(a) v=2.40 m/sv = 2.40\text{ m/s}; (b) ωB=15.0 rad/s\omega_B = 15.0\text{ rad/s}. Convert rA=0.0400 mr_A = 0.0400\text{ m} to get v=(0.0400 m)(60.0 rad/s)=2.40 m/sv = (0.0400\text{ m})(60.0\text{ rad/s}) = 2.40\text{ m/s}. Then ωB=vrB=2.40 m/s0.160 m=15.0 rad/s\omega_B = \frac{v}{r_B} = \frac{2.40\text{ m/s}}{0.160\text{ m}} = 15.0\text{ rad/s}.

03

A belt connects a drive pulley (r1=5.00 cmr_1 = 5.00\text{ cm}) spinning at ω1=80.0 rad/s\omega_1 = 80.0\text{ rad/s} to a driven pulley (r2=20.0 cmr_2 = 20.0\text{ cm}). Determine the centripetal acceleration aca_c of a point on the rim of the driven pulley in m/s2\text{m/s}^2.

Answer

ac=80.0 m/s2a_c = 80.0\text{ m/s}^2. First, v=r1ω1=(0.0500 m)(80.0 rad/s)=4.00 m/sv = r_1 \omega_1 = (0.0500\text{ m})(80.0\text{ rad/s}) = 4.00\text{ m/s}. Next, for the driven pulley with r2=0.200 mr_2 = 0.200\text{ m}, compute ac=v2r2=(4.00 m/s)20.200 m=16.00.200=80.0 m/s2a_c = \frac{v^2}{r_2} = \frac{(4.00\text{ m/s})^2}{0.200\text{ m}} = \frac{16.0}{0.200} = 80.0\text{ m/s}^2 (or via ω2=20.0 rad/s\omega_2 = 20.0\text{ rad/s}, ac=r2ω22=(0.200)(20.0)2=80.0 m/s2a_c = r_2 \omega_2^2 = (0.200)(20.0)^2 = 80.0\text{ m/s}^2).

Loading workspace…