Resources
A laboratory technician performs a calorimetry test to identify the initial furnace temperature of an iron bolt. The bolt has a mass of and a known specific heat capacity of . The red-hot bolt is removed from the furnace and dropped into an insulated container holding of water () at an initial temperature of . The container has negligible heat capacity. The system seals and reaches a stable final equilibrium temperature of without boiling any water. Reconstruct the initial furnace temperature of the bolt just before it was quenched.
Answer and steps
Final answer
Steps
Calculate the Heat Absorbed by the Water
Principle of Calorimetry
In an isolated system with negligible heat exchange with the container and surroundings, the heat gained by the cooler substance equals the heat lost by the hotter substance: The relationship between heat transferred , mass , specific heat capacity , and temperature change is:
The water warms from its initial temperature to the equilibrium temperature :
Using the given mass and specific heat capacity :
Set Up the Heat Loss for the Iron Bolt
As the bolt cools from its initial furnace temperature to , the temperature change is:
The heat released by the bolt is:
Equate Heat Gained and Heat Lost to Solve for
Equating heat lost and heat gained:
Solve for the temperature drop of the bolt:
Now solve for :
(Common Pitfall: Remember to use the absolute temperature difference for heat lost when writing , or use with consistently.)
Typical errors
01 The student subtracts initial from final temperature for both substances without accounting for the opposite signs of heat gained and lost, yielding a negative temperature difference and subtracting it instead of adding.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
or
You set the positive heat absorbed by the water equal to , which is a negative quantity because the bolt cools down. When using , write the temperature change for the cooling object as , or write the conservation law as .
- Step 3Correct
Your algebraic isolation followed correctly from your setup in step 2, but the inherited sign reversal produced an unphysical result of instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified and applied the formula for the water.
You performed the arithmetic for the water's temperature rise and total heat gained accurately.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou equated heat gained to heat lost while keeping without a negative sign.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the two standard calorimetry formulations: either equate magnitude of heat lost to heat gained (, where both sides are positive differences ), or sum all signed heats to zero (, where each ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Physical Reality Check
A hot object cooling down must have an initial temperature higher than the equilibrium temperature.
Always verify that for the substance losing heat; an initial temperature near absolute zero for a red-hot bolt indicates a reversed sign.
- Consistent Heat Accounting
If using , both temperature differences must be positive: and .
Choose between or before substituting numbers.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet heat gained equal to heat lost using positive temperature drops: .
Substitute the known values: .
Divide by : .
Add to both sides: .
02 The student forgets to add the final equilibrium temperature back to the temperature change of the iron bolt, reporting ΔT_Fe as the initial temperature.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
The calculated value is how much the bolt cooled (), not its starting temperature. To find , you must add the final equilibrium temperature to .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the heat absorbed by the water using .
You correctly set up the heat-balance relation .
You accurately solved for the magnitude of the temperature drop of the bolt as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeReporting the temperature change as the initial temperature without adding the final equilibrium temperature .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated as the final quantity sought rather than expanding to solve for the absolute starting temperature.
REASONING PATH
Your ACEpath teacher’s suggested approach- Expand $\Delta T$ explicitly
For a cooling substance, heat loss is proportional to .
Write directly into your equation rather than leaving it as an unexpanded .
- Sanity-check temperature levels
A cooling hot object must start at a temperature higher than both its temperature drop and its final equilibrium temperature.
Check whether ; if your result equals , ask whether the object cooled all the way to .
CORRECTED PATH
ACEpath Teacher's DemonstrationExpress the temperature drop in terms of initial and final temperatures: .
Substitute the known equilibrium temperature: .
Add to both sides to isolate : .
03 The student mistakenly swaps the specific heat capacities of water and iron, using 450 J/(kg·°C) for water and 4186 J/(kg·°C) for iron.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You correctly identified the mass and temperature change of water, but you substituted instead of water's specific heat capacity of .
- Step 2Correct
You correctly set up the temperature drop , but you substituted water's specific heat capacity () for iron rather than iron's value ().
- Step 3Correct
Your algebraic division was carried out correctly according to your earlier expressions, but the values were distorted by the swapped constants.
- Step 4Correct
Your final addition was executed accurately from your previous line, but the result inherits the initial substitution error. A quick physical check reveals that a red-hot bolt from a furnace cannot be only .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly applied the calorimetry conservation principle .
You correctly computed the temperature change of the water .
You carried out the algebraic rearrangement and isolation of with sound arithmetic.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou swapped the numerical values of specific heat capacities between the two materials ( and ).
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating given constants between components when labeling variables, combined with skipping a physical sense check on the magnitude of specific heats (water has an unusually high specific heat capacity around , whereas metals are typically much lower, around ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Explicit Variable Labeling
Write out each material's properties with unambiguous subscripts before calculating: and .
Always verify that the higher specific heat capacity belongs to water () and not the metal.
- Physical Reasonableness Check
Red-hot metal glowing from an industrial furnace must have a temperature of several hundred degrees Celsius.
If a furnace temperature calculates to near room temperature (), stop and re-check whether heat capacities or temperature differences were inverted.
CORRECTED PATH
ACEpath Teacher's DemonstrationLock it in
What are the two valid ways to set up the thermal energy conservation equation for two mixing substances?
Either with every , or where both temperature differences are written as positive values: and .
Similar question
A piece of aluminum () at is placed into of water () at . Assuming an insulated container, determine the final equilibrium temperature .
Answer
. Key steps: .
A unknown metal cylinder is heated to and dropped into of water at . The mixture reaches equilibrium at . Calculate the specific heat capacity of the unknown metal.
Answer
. Key steps: Heat gained by water . Heat lost by metal . Equating gives .
A copper calorimeter cup of mass () contains of water at . A hot steel bolt () is dropped into the water, and the final temperature reaches . Find the bolt's initial temperature .
Answer
. Key steps: Total heat gained by water and cup is . Heat lost by steel is . Setting yields .