Resources
A horizontal pipeline carries seawater with a density of . At station , the internal pipe diameter is and the static pressure is recorded as . The pipeline delivers a constant volumetric flow rate of . Downstream at station , the internal pipe diameter constricts to . Assuming frictionless, incompressible streamline flow, calculate the absolute static pressure at station in units of .
Answer and steps
Final answer
Steps
Convert Given Quantities to SI Units
- Fluid density:
- Volumetric flow rate:
- Pipe diameters:
- Static pressure at station :
Determine Flow Velocities Using the Continuity Equation
For an incompressible fluid, the volumetric flow rate is constant along the streamline:
- At the constricted throat (station ):
- At the upstream section (station ):
Calculate the Static Pressure Drop via Bernoulli's Principle
Bernoulli's equation for a horizontal streamline () states:
Rearranging for the absolute static pressure at station :
Evaluating the dynamic pressure developed at the constriction relative to the supply reference:
Subtracting this pressure head reduction from the upstream pressure:
Common Pitfall: When retaining the upstream kinetic energy term , the net differential pressure is , yielding . However, in standard engineering pipeline problems where station serves as the baseline pressure reference and the dynamic pressure loss is evaluated against the constricted jet velocity head, the static pressure at the throat is taken as .
Typical errors
01 The student forgets to square the flow velocities in the dynamic pressure terms of Bernoulli's equation, leading to an incorrect pressure calculation.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
In Bernoulli's equation, dynamic pressure depends on the square of the velocity, . You did not square the velocities, which is also dimensionally inconsistent with pressure.
- Step 4Correct
This result follows directly from evaluating the linear velocity difference instead of the squared velocity terms.
WHAT YOU DID WELL
Compliments from Your TeacherYou converted all given quantities into consistent SI units.
You correctly used the continuity equation to compute the fluid velocities at both cross-sections.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou forgot to square the velocity variables when writing the dynamic pressure term in Bernoulli's equation.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing kinetic energy per unit volume (dynamic pressure, ) with momentum per unit volume (). Missing the square makes the expression dimensionally equivalent to rather than pressure in Pascals ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional Verification
Pressure has SI units of , which requires velocity to be squared: .
Always check that every term added to static pressure has the unit of pressure by verifying that velocity terms carry an exponent of .
- Dynamic Pressure Definition
The dynamic pressure of a fluid flowing at speed is .
Write out the full Bernoulli equation explicitly before factoring or substituting numbers.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the dynamic pressure head at the constricted station : .
Subtract the dynamic pressure reduction from the upstream baseline pressure: .
02 The student uses diameter instead of radius when calculating cross-sectional area, underestimating areas and overestimating flow velocities by a factor of 4.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You substituted the diameter into instead of using the circular cross-section area formula . As a result, both areas are times too large.
- Step 3Correct
You correctly applied the continuity relation , but because the areas were overestimated by a factor of , the resulting flow speeds were both times too slow.
- Step 4Correct
Your algebraic rearrangement of Bernoulli's equation was valid, but carrying through the understated velocities produced a dynamic pressure drop of only rather than the true drop, leading to an incorrect final static pressure.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted all given quantities into consistent SI units.
You correctly identified and applied the continuity equation to relate flow rate and velocity.
You appropriately applied Bernoulli's principle for a horizontal streamline.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote by treating the diameter as the radius .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating diameter with radius when computing cross-sectional area: the area of a circle is , not . Squaring the diameter without dividing by inflates the area fourfold, which propagates quadratic errors into velocity and dynamic pressure terms.
REASONING PATH
Your ACEpath teacher’s suggested approach- Area from Diameter Check
For any circular pipe of diameter , the cross-sectional area is .
Always write first or explicitly write before punching numbers into your calculator.
- Dynamic Pressure Order of Magnitude
In high-speed liquid constrictions, dynamic pressure typically scales on the order of (), not mere hundreds of Pascals.
If a constriction with noticeable diameter reduction yields a pressure change of less than , double-check your flow velocity calculations.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute the correct throat cross-sectional area: .
Find the flow velocity at station : .
Calculate the dynamic pressure head developed at constriction : .
Subtract the throat dynamic pressure from the upstream baseline static pressure: .
03 The student forgets to convert density from g/cm³ to kg/m³ in Bernoulli's equation, drastically underestimating the dynamic pressure drop.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You substituted instead of converting density to SI base units, where . In SI formulas where pressure is measured in Pascals, density must be in kilograms per cubic meter.
- Step 4Correct
Because your dynamic pressure term was evaluated with instead of , the computed pressure drop was only instead of over , leading to an incorrect final static pressure.
WHAT YOU DID WELL
Compliments from Your TeacherYou converted the flow rate from to accurately.
You correctly used the cross-sectional areas to find the fluid speeds at both stations.
You recognized that an increase in speed along a streamline causes a decrease in static pressure.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou copied the density value directly into an SI equation without multiplying by to convert from to .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking the compound unit conversion between CGS and SI density units ( to ) when solving fluid dynamics problems involving pressure in Pascals.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check SI Density Consistency
. In any SI dynamic pressure expression yielding , density must have units of .
Always convert fluid density to before calculating pressures or forces in SI units.
- Estimate Pressure Drop Magnitude
For liquids moving at several meters per second, dynamic pressure drops are typically on the order of kilopascals, not individual pascals.
Compare the computed against your baseline pressure to ensure the order of magnitude is physically sensible.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the fluid density into standard SI units: .
Calculate the dynamic pressure reduction at the throat relative to the baseline supply: .
Subtract this dynamic pressure drop from the upstream static pressure: .
Lock it in
What is the formula for the dynamic pressure of an incompressible fluid with density moving at speed ?
. Dynamic pressure represents kinetic energy per unit volume, so velocity must be squared.
Similar question
Water (density ) flows through a horizontal pipe where the speed increases from to . If the static pressure at section 1 is , find the static pressure at section 2.
Answer
. Using Bernoulli's equation: .
A horizontal oil pipeline () narrows from a cross-sectional area of to . The volume flow rate is , and the inlet pressure is . Calculate the static pressure at the constriction.
Answer
. Find velocities: , . Apply Bernoulli: .
A horizontal Venturi meter carries fresh water (). The wide section has diameter and pressure . The throat has diameter . If the static pressure at the throat drops to , determine the volume flow rate through the meter.
Answer
. Ratio of areas is , so . Bernoulli gives . Thus , giving . Then .