Resources

A 0.350 kg0.350\text{ kg} copper slug sliding along a rough horizontal table with an initial speed v0=14.0 m/sv_0 = 14.0\text{ m}/\text{s} comes entirely to rest due to kinetic friction. The kinetic friction coefficient is μk=0.280\mu_k = 0.280. Assume that 75.0%75.0\% of the mechanical energy dissipated by non-conservative frictional work is absorbed as an increase in the internal energy of the copper slug, while the remainder is dissipated to the table. If the specific heat capacity of copper is c=385 J/(kg⋅K)c = 385\text{ J}/(\text{kg}\cdot\text{K}), calculate: (a) the work done by friction on the slug, (b) the increase in internal energy ΔUslug\Delta U_{\text{slug}} of the slug, and (c) the temperature rise ΔT\Delta T of the slug.

Answer and steps

Final answer

(a) Wfric=−34.3 JW_{\text{fric}} = -34.3\text{ J}; (b) ΔUslug=25.7 J\Delta U_{\text{slug}} = 25.7\text{ J}; (c) ΔT=0.191 K\Delta T = 0.191\text{ K}.

Steps

Part (a): Work Done by Friction on the Slug

According to the work-energy theorem, the net work done on an object equals the change in its kinetic energy:

Wnet=ΔK=Kf−KiW_{\text{net}} = \Delta K = K_f - K_i

Along the vertical axis, the normal force and gravity balance each other and do zero work. Friction is the only force doing work along the horizontal direction of motion.

Given:

  • Mass of the slug: m=0.350 kgm = 0.350\text{ kg}
  • Initial velocity: v0=14.0 m/sv_0 = 14.0\text{ m/s}
  • Final velocity: vf=0 m/sv_f = 0\text{ m/s}

Calculate the initial kinetic energy:

Ki=12mv02=12(0.350 kg)(14.0 m/s)2=34.3 JK_i = \frac{1}{2} m v_0^2 = \frac{1}{2} (0.350\text{ kg})(14.0\text{ m/s})^2 = 34.3\text{ J}

Since the final kinetic energy is Kf=0 JK_f = 0\text{ J}:

Wfric=0−34.3 J=−34.3 JW_{\text{fric}} = 0 - 34.3\text{ J} = -34.3\text{ J}

(Pitfall note: The work done by kinetic friction on the sliding slug is negative because the friction force opposes the direction of displacement.)


Part (b): Increase in Internal Energy of the Slug

The total mechanical energy dissipated into thermal energy by non-conservative frictional work is:

Ediss=∣Wfric∣=34.3 JE_{\text{diss}} = |W_{\text{fric}}| = 34.3\text{ J}

The problem states that 75.0%75.0\% of this dissipated energy is absorbed into the copper slug, raising its microscopic internal energy:

ΔUslug=0.750⋅Ediss=0.750⋅34.3 J=25.725 J≈25.7 J\Delta U_{\text{slug}} = 0.750 \cdot E_{\text{diss}} = 0.750 \cdot 34.3\text{ J} = 25.725\text{ J} \approx 25.7\text{ J}

The remaining 25.0%25.0\% (8.58 J8.58\text{ J}) is dissipated into the table.


Part (c): Temperature Rise of the Slug

The relationship between the thermal energy gained by a solid substance of mass mm, specific heat capacity cc, and its resulting temperature change ΔT\Delta T is given by:

ΔUslug=mcΔT\Delta U_{\text{slug}} = m c \Delta T

Rearranging for ΔT\Delta T:

ΔT=ΔUslugmc\Delta T = \frac{\Delta U_{\text{slug}}}{m c}

Substitute the values:

  • ΔUslug=25.725 J\Delta U_{\text{slug}} = 25.725\text{ J}
  • m=0.350 kgm = 0.350\text{ kg}
  • c=385 J/(kg⋅K)c = 385\text{ J}/(\text{kg}\cdot\text{K})

ΔT=25.725 J(0.350 kg)(385 J/(kg⋅K))=25.725 J134.75 J/K≈0.191 K\Delta T = \frac{25.725\text{ J}}{(0.350\text{ kg})(385\text{ J}/(\text{kg}\cdot\text{K}))} = \frac{25.725\text{ J}}{134.75\text{ J/K}} \approx 0.191\text{ K}

Thus, the temperature of the copper slug rises by 0.191 K0.191\text{ K} (or equivalently, 0.191 ∘C0.191\ ^\circ\text{C}).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to square the velocity when calculating the initial kinetic energy and work done by friction.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Wf=0−(12)mv0  ⟹  Wf=−2.45 JW_f = 0 - \left(\frac{1}{2}\right) m v_0 \implies W_f = -2.45\text{ J}

    Correct

    Wf=Kf−Ki=0−12mv02=−12(0.350 kg)(14.0 m/s)2=−34.3 JW_f = K_f - K_i = 0 - \frac{1}{2} m v_0^2 = -\frac{1}{2}(0.350\text{ kg})(14.0\text{ m/s})^2 = -34.3\text{ J}

    You correctly applied the work-energy theorem and recognized that friction does negative work, but you wrote kinetic energy as 12mv0\frac{1}{2}mv_0 rather than 12mv02\frac{1}{2}mv_0^2. Forgetting to square v0v_0 gave −2.45 J-2.45\text{ J} instead of −34.3 J-34.3\text{ J}.

  2. Step 2

    ΔUslug=0.750×2.45 J=1.8375 J\Delta U_{\text{slug}} = 0.750 \times 2.45\text{ J} = 1.8375\text{ J}

    Correct

    ΔUslug=0.750×∣Wf∣=0.750×34.3 J≈25.7 J\Delta U_{\text{slug}} = 0.750 \times |W_f| = 0.750 \times 34.3\text{ J} \approx 25.7\text{ J}

    You correctly recognized that 75.0%75.0\% of the dissipated mechanical energy is absorbed into the slug's internal energy, but your result was affected by the initial kinetic energy error from part (a).

  3. Step 3

    ΔT=ΔUslugmc=1.83750.350×385=0.0136 K\Delta T = \frac{\Delta U_{\text{slug}}}{m c} = \frac{1.8375}{0.350 \times 385} = 0.0136\text{ K}

    Correct

    ΔT=ΔUslugmc=25.725 J(0.350 kg)(385 J/(kg⋅K))≈0.191 K\Delta T = \frac{\Delta U_{\text{slug}}}{m c} = \frac{25.725\text{ J}}{(0.350\text{ kg})(385\text{ J}/(\text{kg}\cdot\text{K}))} \approx 0.191\text{ K}

    You correctly related internal energy change to temperature rise using ΔU=mcΔT\Delta U = mc\Delta T, but using 1.8375 J1.8375\text{ J} instead of 25.725 J25.725\text{ J} propagated the earlier calculation error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the work-energy theorem ΔK=Wnet\Delta K = W_{\text{net}} to find the work done by friction.

You correctly identified that the friction work on the stopping slug must be negative.

You correctly applied the 75.0%75.0\% fraction to determine the increase in internal energy.

You correctly rearranged ΔU=mcΔT\Delta U = mc\Delta T to solve for the temperature change.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Kinetic Energy Formula Error

You wrote kinetic energy as 12mv\frac{1}{2}mv instead of 12mv2\frac{1}{2}mv^2, omitting the square on velocity.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

A formula recall slip between momentum-related linear velocity expressions and quadratic kinetic energy led to using 12mv\frac{1}{2}mv instead of 12mv2\frac{1}{2}mv^2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Kinetic Energy Definition
  • K=12mv2K = \frac{1}{2}mv^2

  • Always verify that velocity is squared in energy calculations, checking units: kg⋅(m/s)2=J\text{kg}\cdot(\text{m}/\text{s})^2 = \text{J}.

Dimensional Consistency Check
  • Work and energy have dimensions [M][L]2[T]−2[M][L]^2[T]^{-2}.

  • Notice that 12mv\frac{1}{2}mv has units of kg⋅m/s\text{kg}\cdot\text{m}/\text{s} (momentum), which cannot equal joules.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the initial kinetic energy with the squared speed: Ki=12(0.350 kg)(14.0 m/s)2=34.3 JK_i = \frac{1}{2}(0.350\text{ kg})(14.0\text{ m/s})^2 = 34.3\text{ J}.

  2. Find the work done by friction: Wf=Kf−Ki=0−34.3 J=−34.3 JW_f = K_f - K_i = 0 - 34.3\text{ J} = -34.3\text{ J}.

  3. Compute the absorbed thermal energy: ΔUslug=0.750×34.3 J=25.725 J≈25.7 J\Delta U_{\text{slug}} = 0.750 \times 34.3\text{ J} = 25.725\text{ J} \approx 25.7\text{ J}.

  4. Calculate the temperature rise: ΔT=25.725 J(0.350 kg)(385 J/(kg⋅K))≈0.191 K\Delta T = \frac{25.725\text{ J}}{(0.350\text{ kg})(385\text{ J}/(\text{kg}\cdot\text{K}))} \approx 0.191\text{ K}.

Final answer

(a) Wfric=−34.3 JW_{\text{fric}} = -34.3\text{ J}; (b) ΔUslug=25.7 J\Delta U_{\text{slug}} = 25.7\text{ J}; (c) ΔT=0.191 K\Delta T = 0.191\text{ K}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check velocity exponents whenever evaluating kinetic energy or work-energy problems.

  • Perform a quick unit check: momentum is kg⋅m/s\text{kg}\cdot\text{m}/\text{s}, while kinetic energy requires an extra velocity factor to reach J=kg⋅m2/s2\text{J} = \text{kg}\cdot\text{m}^2/\text{s}^2.

OverviewACEpath Teacher's Diagnosis

02 The student assumes all of the dissipated mechanical energy goes into the slug, ignoring the 75.0% absorption factor.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Wf=ΔK=0−(12)mv02  ⟹  Wf=−0.5×0.350×(14.0)2=−34.3 JW_f = \Delta K = 0 - \left(\frac{1}{2}\right) m v_0^2 \implies W_f = -0.5 \times 0.350 \times (14.0)^2 = -34.3\text{ J}

  2. Step 2

    ΔUslug=∣Wf∣=34.3 J\Delta U_{\text{slug}} = |W_f| = 34.3\text{ J}

    Correct

    ΔUslug=0.750⋅∣Wfric∣=0.750×34.3 J=25.7 J\Delta U_{\text{slug}} = 0.750 \cdot |W_{\text{fric}}| = 0.750 \times 34.3\text{ J} = 25.7\text{ J}

    You equated the increase in internal energy of the slug to the total dissipated mechanical energy, overlooking that only 75.0%75.0\% of the dissipated energy is absorbed by the slug while the remaining 25.0%25.0\% enters the table.

  3. Step 3

    ΔT=ΔUslugmc  ⟹  ΔT=34.30.350×385=0.255 K\Delta T = \frac{\Delta U_{\text{slug}}}{m c} \implies \Delta T = \frac{34.3}{0.350 \times 385} = 0.255\text{ K}

    Correct

    ΔT=ΔUslugmc=25.725 J(0.350 kg)(385 J/(kg⋅K))≈0.191 K\Delta T = \frac{\Delta U_{\text{slug}}}{m c} = \frac{25.725\text{ J}}{(0.350\text{ kg})(385\text{ J}/(\text{kg}\cdot\text{K}))} \approx 0.191\text{ K}

    Your formula and substitution method were correct, but the numerical answer was affected by using 34.3 J34.3\text{ J} instead of 25.7 J25.7\text{ J}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the work-energy theorem to calculate the frictional work done on the slug.

You correctly identified and applied the relationship ΔU=mcΔT\Delta U = m c \Delta T to find the temperature change.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Energy Partition Fraction

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that 100% of the dissipated kinetic energy was transferred to the slug as internal energy, missing the problem's explicit condition that the dissipated mechanical energy is partitioned between two contacting objects (75.0% to the slug and 25.0% to the table).

REASONING PATH
Your ACEpath teacher’s suggested approach
Energy Partitioning across Contact Surfaces
  • When friction dissipates mechanical energy between two bodies, the total thermal energy generated is split between both bodies: Ediss=ΔU1+ΔU2E_{\text{diss}} = \Delta U_1 + \Delta U_2.

  • Always check the problem statement for how dissipated friction energy is distributed between the moving object and the surface.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the portion of dissipated energy absorbed by the slug: ΔUslug=0.750×34.3 J=25.725 J\Delta U_{\text{slug}} = 0.750 \times 34.3\text{ J} = 25.725\text{ J}.

  2. Substitute this value into the thermal equation: ΔT=25.725 J(0.350 kg)(385 J/(kg⋅K))≈0.191 K\Delta T = \frac{25.725\text{ J}}{(0.350\text{ kg})(385\text{ J}/(\text{kg}\cdot\text{K}))} \approx 0.191\text{ K}.

Final answer

(a) Wfric=−34.3 JW_{\text{fric}} = -34.3\text{ J}; (b) ΔUslug=25.7 J\Delta U_{\text{slug}} = 25.7\text{ J}; (c) ΔT=0.191 K\Delta T = 0.191\text{ K}

NEXT STEPS
Final Takeaways from Your Teacher
  • Re-read thermal conversion word problems carefully to identify whether energy dissipation is shared between multiple bodies.

  • Practise calculating temperature rise when an explicit absorption fraction or efficiency is provided.

OverviewACEpath Teacher's Diagnosis

03 The student omits the mass in the heat capacity formula, confusing heat capacity with specific heat capacity.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Wf=0−(12)mv02  ⟹  Wf=−0.5×0.350×(14.0)2=−34.3 JW_f = 0 - \left(\frac{1}{2}\right)m v_0^2 \implies W_f = -0.5 \times 0.350 \times (14.0)^2 = -34.3\text{ J}

  2. Step 2

    ΔUslug=0.750×34.3 J=25.725 J\Delta U_{\text{slug}} = 0.750 \times 34.3\text{ J} = 25.725\text{ J}

  3. Step 3

    ΔT=ΔUslugc  ⟹  ΔT=25.725385=0.0668 K\Delta T = \frac{\Delta U_{\text{slug}}}{c} \implies \Delta T = \frac{25.725}{385} = 0.0668\text{ K}

    Correct

    ΔT=ΔUslugmc=25.725 J(0.350 kg)(385 J/(kg⋅K))≈0.191 K\Delta T = \frac{\Delta U_{\text{slug}}}{m c} = \frac{25.725\text{ J}}{(0.350\text{ kg})(385\text{ J}/(\text{kg}\cdot\text{K}))} \approx 0.191\text{ K}

    Specific heat capacity cc has units of J/(kg⋅K)\text{J}/(\text{kg}\cdot\text{K}), which represents the energy needed per unit mass. Therefore, you must divide by both mass mm and specific heat capacity cc using ΔU=mcΔT\Delta U = m c \Delta T.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the work-energy theorem to find the work done by friction.

You correctly identified that the mechanical energy dissipated equals the magnitude of the work done by friction.

You accurately found the 75.0%75.0\% fraction absorbed as internal energy.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Mass in Specific Heat Formula

You used the total heat capacity formula Q=CΔTQ = C\Delta T with the specific heat capacity numerical value cc, omitting the mass factor mm.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing specific heat capacity cc (an intensive property with units J/(kg⋅K)\text{J}/(\text{kg}\cdot\text{K})) with extensive heat capacity C=mcC = mc (with units J/K\text{J}/\text{K}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit Dimensional Check
  • Always verify that [ΔU]=[m][c][ΔT]  ⟹  J=(kg)(J/(kg⋅K))(K)[\Delta U] = [m][c][\Delta T] \implies \text{J} = (\text{kg})(\text{J}/(\text{kg}\cdot\text{K}))(\text{K}).

  • If cc has kg\text{kg} in the denominator of its unit, include mass mm in the denominator when solving for temperature change.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the specific heat formula relating internal energy to temperature change: ΔUslug=mcΔT\Delta U_{\text{slug}} = m c \Delta T.

  2. Isolate ΔT\Delta T: ΔT=ΔUslugmc\Delta T = \frac{\Delta U_{\text{slug}}}{m c}.

  3. Substitute m=0.350 kgm = 0.350\text{ kg} and c=385 J/(kg⋅K)c = 385\text{ J}/(\text{kg}\cdot\text{K}): ΔT=25.725 J(0.350 kg)(385 J/(kg⋅K))=25.725134.75≈0.191 K\Delta T = \frac{25.725\text{ J}}{(0.350\text{ kg})(385\text{ J}/(\text{kg}\cdot\text{K}))} = \frac{25.725}{134.75} \approx 0.191\text{ K}.

Final answer

(a) Wfric=−34.3 JW_{\text{fric}} = -34.3\text{ J}; (b) ΔUslug=25.7 J\Delta U_{\text{slug}} = 25.7\text{ J}; (c) ΔT=0.191 K\Delta T = 0.191\text{ K}

NEXT STEPS
Final Takeaways from Your Teacher
  • Check the units of the given heat capacity: if it contains per kilogram (kg−1\text{kg}^{-1}), multiply by mass mm.

  • Practice converting between heat capacity CC and specific heat capacity c=C/mc = C/m.

Lock it in

Similar question

01

A 0.500 kg0.500\text{ kg} aluminum block (c=900 J/(kg⋅K)c = 900\text{ J}/(\text{kg}\cdot\text{K})) slides on a rough floor with an initial speed of 12.0 m/s12.0\text{ m/s} and stops. If 60.0%60.0\% of the mechanical energy lost to friction is absorbed by the block, calculate its temperature change ΔT\Delta T.

Answer

Ki=12(0.500)(12.0)2=36.0 JK_i = \frac{1}{2}(0.500)(12.0)^2 = 36.0\text{ J}. Absorbed energy: ΔU=0.600×36.0 J=21.6 J\Delta U = 0.600 \times 36.0\text{ J} = 21.6\text{ J}. Temperature rise: ΔT=ΔUmc=21.6(0.500)(900)=0.048 K\Delta T = \frac{\Delta U}{mc} = \frac{21.6}{(0.500)(900)} = 0.048\text{ K}.

02

A lead bullet of mass 0.020 kg0.020\text{ kg} (c=128 J/(kg⋅K)c = 128\text{ J}/(\text{kg}\cdot\text{K})) moving at 240 m/s240\text{ m/s} embeds into a stationary wooden block and stops. Assuming 80.0%80.0\% of its initial kinetic energy is converted into internal energy of the bullet, what is the temperature rise of the bullet?

Answer

Ki=12(0.020 kg)(240 m/s)2=576 JK_i = \frac{1}{2}(0.020\text{ kg})(240\text{ m/s})^2 = 576\text{ J}. Energy absorbed: ΔU=0.800×576 J=460.8 J\Delta U = 0.800 \times 576\text{ J} = 460.8\text{ J}. Temperature rise: ΔT=ΔUmc=460.8(0.020)(128)=180 K\Delta T = \frac{\Delta U}{mc} = \frac{460.8}{(0.020)(128)} = 180\text{ K}.

03

A 1.20 kg1.20\text{ kg} steel glider (c=450 J/(kg⋅K)c = 450\text{ J}/(\text{kg}\cdot\text{K})) slows down from 20.0 m/s20.0\text{ m/s} to 8.00 m/s8.00\text{ m/s} due to friction on a rough track. If the glider absorbs 70.0%70.0\% of the dissipated mechanical energy, determine: (a) the work done by friction on the glider, and (b) its temperature increase ΔT\Delta T.

Answer

(a) Wf=ΔK=12(1.20)(8.002−20.02)=0.600(64−400)=−201.6 J≈−202 JW_f = \Delta K = \frac{1}{2}(1.20)(8.00^2 - 20.0^2) = 0.600(64 - 400) = -201.6\text{ J} \approx -202\text{ J}.\n(b) Dissipated energy: Ediss=201.6 JE_{\text{diss}} = 201.6\text{ J}. Energy absorbed: ΔU=0.700×201.6 J=141.12 J\Delta U = 0.700 \times 201.6\text{ J} = 141.12\text{ J}. Temperature change: ΔT=ΔUmc=141.12(1.20)(450)≈0.261 K\Delta T = \frac{\Delta U}{mc} = \frac{141.12}{(1.20)(450)} \approx 0.261\text{ K}.

Loading workspace…