Resources
In a physics lab experiment on rotational dynamics, a student uses a rotary motion sensor connected to a computer interface to determine the unknown moment of inertia of a flywheel disk. A light string wrapped around the disk axle of radius is threaded over an ideal pulley and tied to a hanging mass of . The sensor records a steady linear downward acceleration of the mass upon release. Taking , identify the rotational analog of Newton's second law applicable to the flywheel, write the coupled equations for string tension and angular acceleration , and calculate the experimental moment of inertia of the disk.
Answer and steps
Final answer
Newton's Second Law for Rotation; with and ; .
Steps
Identify the Applicable Physical Law
The disk rotates about a fixed axis under the influence of an applied torque produced by the tension in the wrapped string. The rotational analog of Newton's second law relating the net external torque to the resulting angular acceleration is:
where represents the rotational inertia (moment of inertia) of the flywheel system.
Formulate the Coupled Equations
To find the moment of inertia , we analyze the linear motion of the falling mass and the rotational motion of the disk axle:
- Translational Motion of the Hanging Mass ():
Choosing the downward direction as positive: Solving for the tension in the string: - No-Slip Condition:
Assuming the string unwinds without slipping along the axle of radius , the linear acceleration of the string connects directly to the angular acceleration by: - Rotational Motion of the Flywheel Disk:
The tension acts tangentially at radius , producing a net torque: Applying Newton's second law for rotation:
Common Pitfall: Assuming the string tension simply equals the static weight (). Because the hanging mass is accelerating downward, the tension must be strictly less than the weight ().
Calculate the Numerical Values
Substitute the given values into each relation:
- Tension ():
- Angular Acceleration ():
- Net Torque ():
- Moment of Inertia ():
Typical errors
01 The student assumes the tension in the string equals the static weight of the hanging mass rather than accounting for its downward acceleration.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because the hanging mass accelerates downward at , the net force on it is non-zero (). Assuming ignores this downward acceleration and overestimates the tension.
- Step 3
- Step 4Correct
Your algebraic isolation of and subsequent calculation were executed properly, but the result inherited the inaccurate tension value from Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou identified the correct rotational dynamic equation .
You related linear acceleration to angular acceleration using the no-slip condition .
You properly formulated the torque balance and isolated the moment of inertia .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou equated tension to weight () even though the hanging mass was accelerating downward.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the hanging mass as a static load rather than setting up a dynamic free-body diagram using Newton's second law () for translational motion.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Mass Acceleration
If a connected hanging mass has non-zero downward acceleration , then .
Always draw a free-body diagram for moving masses and apply before calculating string tension.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply Newton's second law to the hanging mass: .
Substitute the given acceleration values: .
Calculate net torque: .
Solve for moment of inertia: .
Newton's Second Law for Rotation; with and ;
02 The student inverts the kinematic relation connecting linear and angular acceleration, writing α = ar instead of α = a/r.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Linear acceleration and angular acceleration are related by the no-slip condition . Dividing both sides by gives , not .
- Step 3Correct
Your torque equation was set up correctly, but substituting the incorrect angular acceleration carried the error into your final moment of inertia.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly analyzed the linear forces on the hanging mass to determine the string tension.
You identified the correct rotational form of Newton's second law relating torque to rotational inertia via .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou multiplied the linear acceleration by the radius rather than dividing by it to find the angular acceleration.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the direction of the scale factor when converting between linear and angular kinematics ( vs. ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Check the units and dimensions
Linear quantities have units with meters (), while angular quantities use radians (). Multiplying an acceleration by a radius yields , not .
Always verify that linear equals angular times radius: , , and .
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the tangential acceleration relation: .
Substitute , , and into the rotational equation: .
Compute the result: .
03 The student omits the axle radius when relating torque to tension, writing τ = T instead of τ = rT.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
Torque is the product of the applied force and its perpendicular distance (lever arm) from the rotation axis. You equated torque directly to force (), omitting the axle radius .
- Step 5Correct
Your final calculation followed your formula correctly, but the numerical result is off by a factor of due to the missing lever arm in Step 4.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified and applied Newton's second law for rotation: .
You set up the linear equation of motion for the accelerating mass and found the string tension.
You converted linear acceleration to angular acceleration using .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated torque and force as equivalent quantities by writing rather than .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing force with torque, overlooking that torque requires multiplying the tangential force by the perpendicular distance from the axis of rotation.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check physical dimensions
Force has units of Newtons (), whereas torque has units of Newton-meters ().
Always verify that every torque term has dimensions of force multiplied by length before substituting into .
- Identify the lever arm
For a tangential force applied at a cylindrical surface of radius , the torque magnitude is .
Explicitly draw the force vector at its point of contact and write before equating to .
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the torque produced by tension acting tangentially at radius : .
Equate this torque to : .
Substitute , , and into the expression: .
Lock it in
For a mass hanging from a string and accelerating downward at acceleration , what is the tension in the string?
. By Newton's second law (), downward acceleration requires .
Similar question
A string wrapped around a wheel of radius is pulled downward by an attached falling mass of . The mass accelerates downward at . Taking , find the string tension and the torque applied to the wheel.
Answer
, . Dynamic equation for the mass: . Net torque: .
A cylindrical pulley of unknown moment of inertia has radius . A block of mass unwinds a cord from the pulley, accelerating downward at . With , find the experimental moment of inertia of the pulley.
Answer
. First find tension: . Find angular acceleration: . Then .
A flywheel of radius and moment of inertia is accelerated from rest by a hanging mass descending under gravity (). Determine the linear downward acceleration of the mass.
Answer
. Coupled equations: and . Substituting gives .