Resources
A mass of of steam at is bubbled into a container holding of ice at . Counter to the intuitive expectation that equal masses of steam and ice will average out to liquid water at , the massive latent heat of vaporization dramatically alters the final phase distribution. Assuming an isolated system with no heat loss, determine the final equilibrium temperature of the mixture and the mass of steam remaining uncondensed at equilibrium. Use , , and .
Answer and steps
Final answer
,
Steps
Calculate the heat required to convert the ice to water at
To find the final equilibrium state of the mixture, we compare the maximum thermal energy the ice can absorb to reach against the thermal energy released if all the steam were to condense.
The ice undergoes two processes: melting into liquid water at , and warming from to .
- Heat to melt the ice completely ():
- Heat to warm the melted water from to ():
The total heat absorbed by the ice to reach liquid water at is:
Compare with the heat released by condensing steam
If the entire mass of steam were to condense at , the heat released would be:
Because (), only a fraction of the steam needs to condense to warm all of the ice to liquid water at .
Since both liquid water and uncondensed steam coexist at equilibrium, the system reaches phase equilibrium at the boiling point:
Determine the mass of steam remaining
The mass of steam that condenses to supply is:
Subtracting the condensed steam from the initial mass of steam gives the mass remaining uncondensed:
Typical errors
01 The student assumes all steam condenses into water and solves for an impossible equilibrium temperature above 100°C, concluding that no steam remains uncondensed.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You assumed that all of steam condenses and then cools as liquid water. In phase-change calorimetry, you must first test whether complete condensation is possible by comparing the maximum heat the ice can absorb ( to reach ) with the total heat released by condensation ().
- Step 3Correct
Your resulting temperature of exceeds the boiling point of water, which is a key signal that liquid water cannot exist at this temperature under atmospheric pressure and that the system has reached phase equilibrium at .
- Step 4
m_ = 0_
CorrectBecause the equilibrium state is a mixture of boiling water and steam at , only of steam condenses, leaving of steam uncondensed.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the latent heat required to melt the ice completely ().
You used the correct specific heat and latent heat constants in your algebraic setup.
You solved your linear equation algebraically without calculation slips.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou assumed a single final liquid phase and set up with an unknown temperature without first comparing the maximum heat required to bring the colder substance to the phase boundary against the latent heat released by the hotter substance.
REASONING PATH
Your ACEpath teacher’s suggested approach- Perform an Energy Budget Check
Before setting up a single heat balance equation with an unknown temperature , compute the energy needed to bring each substance to the phase boundary ( or ).
Calculate and compare it with .
- Sanity-Check Temperature Boundaries
In an isolated mixture of ice at and steam at , the final equilibrium temperature must satisfy .
If your calculated temperature falls outside , reject the assumed final phase and recognize that an incomplete phase transition occurred at or .
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the total heat needed to convert all ice at to liquid water at : .
Calculate the heat released if all steam condenses at : .
Compare the two values: since (), only part of the steam condenses, meaning liquid water and uncondensed steam coexist at equilibrium. Thus, .
Determine the mass of steam that condenses to provide : .
Find the remaining steam mass: .
,
02 The student forgets to account for the heat needed to warm the melted ice from 0°C to 100°C, considering only the melting of ice when calculating how much steam condenses.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
Since steam has excess energy, steam and water coexist at
- Step 3Correct
You only supplied heat to melt the ice at , but the melted water must also be warmed to the equilibrium temperature of by absorbing .
- Step 4Correct
Your subtraction step is logically correct, but the numerical result is affected by the undercalculated condensed mass from Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the latent heat of fusion for ice and latent heat of vaporization for steam.
You recognized that steam supplies excess energy, meaning the final system coexists at .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated melting as the sole thermal process the ice undergoes, overlooking that the resulting liquid water at must be raised in temperature to match the final equilibrium state at .
REASONING PATH
Your ACEpath teacher’s suggested approach- Account for every thermal stage
When a cold substance melts into an equilibrium mixture at a higher temperature , it absorbs both latent heat of fusion and sensible heat: .
Always trace the cold mass along the full temperature-energy curve until it matches before setting up your energy-conservation equation.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the sensible heat needed to warm the melted ice to : .
Find the total heat absorbed by the ice to reach liquid at : .
Determine the mass of steam that must condense: .
Subtract the condensed mass from the initial steam mass: .
03 The student correctly calculates the mass of steam that condenses but reports this condensed mass as the remaining uncondensed steam instead of subtracting it from the initial steam mass.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
You equated the mass of remaining uncondensed steam to the condensed mass, rather than subtracting the condensed portion from the initial of steam.
WHAT YOU DID WELL
Compliments from Your TeacherYou calculated both the heat of fusion and sensible heating for the ice accurately.
You correctly recognized that the condensation energy exceeded the ice's absorption capacity, leading to thermal equilibrium at .
You used the latent heat of vaporization correctly to find the condensed mass.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou equated the remaining steam mass directly to the condensed steam mass.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou solved for the quantity that underwent the phase change () but forgot to apply the conservation relationship to find the mass left in the original phase.
REASONING PATH
Your ACEpath teacher’s suggested approach- Distinguish Reacted vs. Remaining Quantities
For any phase transition where only part of a substance changes state, .
Always explicitly write out the subtraction from the initial total mass before boxing the final answer.
CORRECTED PATH
ACEpath Teacher's DemonstrationStart with the initial mass of steam: .
Subtract the mass of steam that condensed into liquid water: .
Compute the remaining mass of uncondensed steam: (or if using ).
,
Lock it in
In calorimetry problems involving phase changes, why must you calculate boundary energy budgets before writing ?
Because you cannot assume all substance undergoes a complete phase transition; comparing maximum heats identifies whether the system stops at a phase boundary ( or ).
Similar question
A mass of of steam at is added to of liquid water at . Determine whether all the steam condenses and find the final equilibrium temperature. (Use and ).
Answer
. Heat needed to warm water to is . Heat released if all steam condenses is . Since , all steam condenses and cools to : , giving .
A mass of of ice at is mixed with of steam at in an insulated container. Find the final equilibrium temperature and the mass of ice melted. (Use , , ).
Answer
, . Total heat released by steam condensing and cooling to is . Heat needed to melt all ice is . Since , not all ice melts, so and .
An insulated calorimeter contains of ice at . Steam at is bubbled in until the entire mixture reaches liquid water at . Determine the required mass of steam. (Use , , , ).
Answer
. Heat absorbed by ice to reach water: . Each kilogram of steam condensing and cooling to releases . Thus, .