Resources

A uniform banner of mass M=8.50 kgM = 8.50\text{ kg} is suspended between two identical vertical support posts. A worker pulls horizontally on both ends of a flexible, lightweight cable supporting the banner until the sag angle θ\theta between the cable and the horizontal becomes extremely small. Construct the vertical component equilibrium equation from the free-body diagram of the banner-cable junction, evaluate the expression for the required cable tension T(θ)T(\theta) as θ→0∘\theta \to 0^\circ, and determine the exact cable tension required if the cable sags by only θ=1.20∘\theta = 1.20^\circ. Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

T(θ)=Mg2sin⁡θT(\theta) = \frac{Mg}{2\sin\theta} (with T→∞T \to \infty as θ→0∘\theta \to 0^\circ); T(1.20∘)=1.99×103 NT(1.20^\circ) = 1.99\times 10^3\text{ N}

Steps

01

Free-Body Diagram and Force Resolution

Consider the banner and the central junction supporting it in static equilibrium:

  • The downward gravitational force acting on the banner is its weight: W=MgW = Mg
  • The tension force TT acts symmetrically along both segments of the cable, directed at an angle θ\theta above the horizontal on each side.

Resolving the tension forces into components:

  • Horizontal components: Tcos⁡θT\cos\theta acting to the left and Tcos⁡θT\cos\theta acting to the right. These cancel each other out: ∑Fx=Tcos⁡θ−Tcos⁡θ=0\sum F_x = T\cos\theta - T\cos\theta = 0
  • Vertical components: Each side of the cable contributes an upward vertical component of Tsin⁡θT\sin\theta.

02

Vertical Equilibrium Equation

For the system to remain in static equilibrium, the sum of all vertical forces must equal zero: ∑Fy=2Tsin⁡θ−Mg=0\sum F_y = 2T\sin\theta - Mg = 0

Solving for the cable tension T(θ)T(\theta): T(θ)=Mg2sin⁡θT(\theta) = \frac{Mg}{2\sin\theta}


03

Limiting Behavior as θ→0∘\theta \to 0^\circ

As the cable is pulled tighter and the sag angle approaches zero: lim⁡θ→0∘sin⁡θ=0  ⟹  lim⁡θ→0∘T(θ)=lim⁡θ→0∘Mg2sin⁡θ=∞\lim_{\theta \to 0^\circ} \sin\theta = 0 \implies \lim_{\theta \to 0^\circ} T(\theta) = \lim_{\theta \to 0^\circ} \frac{Mg}{2\sin\theta} = \infty

Physical Insight: A completely horizontal cable (θ=0∘\theta = 0^\circ) has zero vertical component (Tsin⁡0∘=0T\sin 0^\circ = 0). Consequently, it is physically impossible to support any finite weight without some amount of sag, no matter how large the pulling tension is.


04

Calculation for θ=1.20∘\theta = 1.20^\circ

Substitute the given numerical values into the formula:

  • M=8.50 kgM = 8.50\text{ kg}
  • g=9.80 m/s2g = 9.80\text{ m/s}^2
  • θ=1.20∘\theta = 1.20^\circ

First, compute the weight MgMg: Mg=8.50 kg×9.80 m/s2=83.3 NMg = 8.50\text{ kg} \times 9.80\text{ m/s}^2 = 83.3\text{ N}

Next, evaluate the sine of the angle: sin⁡(1.20∘)≈0.02094\sin(1.20^\circ) \approx 0.02094

Now calculate the tension: T(1.20∘)=83.3 N2×0.02094=83.3 N0.04188≈1.99×103 NT(1.20^\circ) = \frac{83.3\text{ N}}{2 \times 0.02094} = \frac{83.3\text{ N}}{0.04188} \approx 1.99 \times 10^3\text{ N}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the vertical and horizontal trigonometric projections, using cos θ instead of sin θ for the vertical component.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    2Tcos⁡θ−Mg=0  ⟹  2Tcos⁡θ=Mg2T\cos\theta - Mg = 0 \implies 2T\cos\theta = Mg

    Correct

    ∑Fy=2Tsin⁡θ−Mg=0  ⟹  2Tsin⁡θ=Mg\sum F_y = 2T\sin\theta - Mg = 0 \implies 2T\sin\theta = Mg

    Because the sag angle θ\theta is defined between the cable and the horizontal, the side opposite to θ\theta is the vertical component (Ty=Tsin⁡θT_y = T\sin\theta). Using cos⁡θ\cos\theta projects onto the horizontal axis instead.

  2. Step 2

    T(θ)=Mg2cos⁡θT(\theta) = \frac{Mg}{2\cos\theta}

    Correct

    T(θ)=Mg2sin⁡θT(\theta) = \frac{Mg}{2\sin\theta}

    Your algebraic isolation of T(θ)T(\theta) is mechanically correct, but it carries forward the incorrect trigonometric function from Step 1.

  3. Step 3

    As θ→0∘,  cos⁡0∘=1, so T→Mg2=41.65 N\text{As } \theta \to 0^\circ,\; \cos 0^\circ = 1,\text{ so } T \to \frac{Mg}{2} = 41.65\text{ N}

    Correct

    lim⁡θ→0∘T(θ)=lim⁡θ→0∘Mg2sin⁡θ=∞\lim_{\theta \to 0^\circ} T(\theta) = \lim_{\theta \to 0^\circ} \frac{Mg}{2\sin\theta} = \infty

    Because the vertical component must be Tsin⁡θT\sin\theta, as θ→0∘\theta \to 0^\circ the denominator sin⁡θ→0\sin\theta \to 0, causing tension to approach infinity. A completely horizontal cable cannot provide any upward force.

  4. Step 4

    T=8.50×9.802cos⁡1.20∘=83.32×0.99978=41.7 NT = \frac{8.50 \times 9.80}{2\cos 1.20^\circ} = \frac{83.3}{2 \times 0.99978} = 41.7\text{ N}

    Correct

    T=83.3 N2sin⁡1.20∘=83.3 N2×0.02094≈1.99×103 NT = \frac{83.3\text{ N}}{2\sin 1.20^\circ} = \frac{83.3\text{ N}}{2 \times 0.02094} \approx 1.99 \times 10^3\text{ N}

    Your numerical arithmetic is accurate, but substituting into the cos⁡θ\cos\theta formula yields 41.7 N41.7\text{ N} instead of the required 1.99×103 N1.99 \times 10^3\text{ N}.

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that two symmetric cable tensions support the banner against its downward gravitational weight.

You correctly formed an equilibrium equation of the form ∑Fy=0\sum F_y = 0.

You executed all algebraic steps and arithmetic calculations cleanly and accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric Component Confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You selected cos⁡θ\cos\theta instead of sin⁡θ\sin\theta for the vertical component because you did not verify whether θ\theta was adjacent or opposite to the vertical axis in your free-body diagram.

REASONING PATH
Your ACEpath teacher’s suggested approach
Reference Axis Check
  • If an angle θ\theta is measured from the horizontal, the horizontal component is adjacent (Tcos⁡θT\cos\theta) and the vertical component is opposite (Tsin⁡θT\sin\theta).

  • Always sketch a right triangle with the force vector as the hypotenuse and clearly label which leg corresponds to the vertical axis before writing equilibrium equations.

Physical Limiting Check
  • As a suspended cable becomes completely flat (θ→0∘\theta \to 0^\circ), its vertical support drops to zero, requiring infinite tension to balance any non-zero weight.

  • Check whether your expression yields T→∞T \to \infty when θ→0∘\theta \to 0^\circ. A finite non-zero value at θ=0∘\theta = 0^\circ indicates that your components are swapped.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Resolve the vertical components of the two cable segments: Ty=Tsin⁡θT_y = T\sin\theta on each side.

  2. Set the vertical equilibrium: 2Tsin⁡θ−Mg=0  ⟹  T(θ)=Mg2sin⁡θ2T\sin\theta - Mg = 0 \implies T(\theta) = \frac{Mg}{2\sin\theta}.

  3. Evaluate the limit: as θ→0∘\theta \to 0^\circ, sin⁡θ→0\sin\theta \to 0, so T→∞T \to \infty.

  4. Substitute θ=1.20∘\theta = 1.20^\circ: T=8.50×9.802sin⁡1.20∘=83.32×0.02094≈1.99×103 NT = \frac{8.50 \times 9.80}{2\sin 1.20^\circ} = \frac{83.3}{2 \times 0.02094} \approx 1.99 \times 10^3\text{ N}.

Final answer

T(θ)=Mg2sin⁡θT(\theta) = \frac{Mg}{2\sin\theta} (with T→∞T \to \infty as θ→0∘\theta \to 0^\circ); T(1.20∘)=1.99×103 NT(1.20^\circ) = 1.99 \times 10^3\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Draw right triangles directly on your free-body diagram to visually confirm opposite (sin⁡\sin) versus adjacent (cos⁡\cos) legs.

  • Use limiting cases (such as θ=0∘\theta = 0^\circ and θ=90∘\theta = 90^\circ) as a quick sanity check on your component equations.

OverviewACEpath Teacher's Diagnosis

02 The student accounts for tension from only one side of the cable instead of both symmetric sides supporting the load.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Tsin⁡θ−Mg=0  ⟹  Tsin⁡θ=Mg  ⟹  T(θ)=Mgsin⁡θT\sin\theta - Mg = 0 \implies T\sin\theta = Mg \implies T(\theta) = \frac{Mg}{\sin\theta}

    Correct

    2Tsin⁡θ−Mg=0  ⟹  T(θ)=Mg2sin⁡θ2T\sin\theta - Mg = 0 \implies T(\theta) = \frac{Mg}{2\sin\theta}

    The banner is suspended between two posts, meaning the cable pulls upward and outward on both the left and right sides of the central junction. Each side provides an upward force of Tsin⁡θT\sin\theta, so the total upward force is 2Tsin⁡θ2T\sin\theta.

  2. Step 2

    As θ→0∘, sin⁡θ→0, so T→∞\text{As } \theta \to 0^\circ,\, \sin\theta \to 0,\, \text{so } T \to \infty

    Correct

    lim⁡θ→0∘T(θ)=lim⁡θ→0∘Mg2sin⁡θ=∞\lim_{\theta \to 0^\circ} T(\theta) = \lim_{\theta \to 0^\circ} \frac{Mg}{2\sin\theta} = \infty

    Your qualitative limit reasoning is correct, but it evaluates your expression from Step 1 which is missing the factor of 22 in the denominator.

  3. Step 3

    T=8.50×9.80sin⁡1.20∘  ⟹  T=83.30.020942=3978 N≈3980 NT = \frac{8.50 \times 9.80}{\sin 1.20^\circ} \implies T = \frac{83.3}{0.020942} = 3978\text{ N} \approx 3980\text{ N}

    Correct

    T(1.20∘)=83.3 N2×sin⁡1.20∘≈1.99×103 NT(1.20^\circ) = \frac{83.3\text{ N}}{2 \times \sin 1.20^\circ} \approx 1.99 \times 10^3\text{ N}

    You substituted the correct values and evaluated the arithmetic accurately, but because the denominator was missing the factor of 22, your calculated tension is exactly double the correct value.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the vertical component of the tension involves the sine of the sag angle.

You correctly recognized that as θ→0∘\theta \to 0^\circ, sin⁡θ→0\sin\theta \to 0, forcing the required tension toward infinity.

You accurately calculated the banner's weight MgMg and performed the numerical division cleanly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing Symmetric Force Component

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You isolated only one side of the suspended cable when setting up vertical equilibrium, omitting the identical upward vertical force contributed by the other side.

REASONING PATH
Your ACEpath teacher’s suggested approach
Count All Cable Segments at the Junction
  • Every cable segment leaving a junction pulls outward along its length with tension TT.

  • Always draw a free-body diagram around the junction and verify that every attached segment is accounted for in ∑Fy\sum F_y.

Exploit Symmetry in Suspensions
  • For a symmetrical V-shaped suspension holding a load WW, the two upward components combine: 2Tsin⁡θ=W2T\sin\theta = W.

  • Multiply the single-side vertical component by 22 whenever identical symmetric cables support a central load.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Sum the vertical forces from both symmetric sides of the cable: ∑Fy=2Tsin⁡θ−Mg=0\sum F_y = 2T\sin\theta - Mg = 0.

  2. Solve for the cable tension: T(θ)=Mg2sin⁡θT(\theta) = \frac{Mg}{2\sin\theta}.

  3. Substitute M=8.50 kgM = 8.50\text{ kg}, g=9.80 m/s2g = 9.80\text{ m/s}^2, and θ=1.20∘\theta = 1.20^\circ: T=83.3 N2×sin⁡1.20∘=83.3 N0.04188≈1.99×103 NT = \frac{83.3\text{ N}}{2 \times \sin 1.20^\circ} = \frac{83.3\text{ N}}{0.04188} \approx 1.99 \times 10^3\text{ N}.

Final answer

T(θ)=Mg2sin⁡θT(\theta) = \frac{Mg}{2\sin\theta} (with T→∞T \to \infty as θ→0∘\theta \to 0^\circ); T(1.20∘)=1.99×103 NT(1.20^\circ) = 1.99\times 10^3\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch a complete free-body diagram showing both the left and right tension vectors before writing equilibrium equations.

  • Practice checking whether a suspended load is supported by one rope segment or shared across multiple symmetric segments.

  • Work through the flashcards and practice problems below to reinforce symmetric force resolution.

OverviewACEpath Teacher's Diagnosis

03 The student calculates using angle values in radians instead of degrees when taking the sine of 1.20°.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    2Tsin⁡θ−Mg=0  ⟹  2Tsin⁡θ=Mg  ⟹  T(θ)=Mg2sin⁡θ2T\sin\theta - Mg = 0 \implies 2T\sin\theta = Mg \implies T(\theta) = \frac{Mg}{2\sin\theta}

  2. Step 2

    As θ→0∘,sin⁡θ→0, so T→∞\text{As } \theta \to 0^\circ, \sin\theta \to 0, \text{ so } T \to \infty

  3. Step 3

    T=8.50×9.802sin⁡(1.20)  ⟹  sin⁡(1.20 rad)=0.9320T = \frac{8.50 \times 9.80}{2\sin(1.20)} \implies \sin(1.20\text{ rad}) = 0.9320

    Correct

    sin⁡(1.20∘)≈0.02094\sin(1.20^\circ) \approx 0.02094

    You evaluated the trigonometric function using 1.20 rad1.20\text{ rad} instead of 1.20∘1.20^\circ. Always verify whether the input angle is in degrees or radians before calculating.

  4. Step 4

    T=83.32×0.9320=44.7 NT = \frac{83.3}{2 \times 0.9320} = 44.7\text{ N}

    Correct

    T=83.3 N2×0.02094≈1.99×103 NT = \frac{83.3\text{ N}}{2 \times 0.02094} \approx 1.99 \times 10^3\text{ N}

    Your arithmetic follows correctly from your previous trigonometric value, but the final result is altered because sin⁡(1.20 rad)\sin(1.20\text{ rad}) was used.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly resolved the vertical components of the two cable segments and formulated the equilibrium condition.

You accurately isolated the tension variable T(θ)T(\theta) algebraically.

You correctly identified that the tension diverges to infinity as the sag angle approaches zero.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Angle Unit Error (Radians vs. Degrees)

You evaluated sin⁡(1.20)\sin(1.20) with your calculator set to radian mode instead of calculating sin⁡(1.20∘)\sin(1.20^\circ) in degree mode.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating degree and radian angle measurements when entering small angles into trigonometric functions, and overlooking the degree symbol (∘^\circ) in the problem statement.

REASONING PATH
Your ACEpath teacher’s suggested approach
Angle Mode Verification
  • Trigonometric functions require calculator mode to match the specified angle unit (degrees ∘^\circ vs. radians rad\text{rad}).

  • Check your calculator display for 'DEG' whenever the angle is written with a degree symbol (∘^\circ) before computing sine or cosine.

Physical Sanity Check for Shallow Sag
  • For a very small sag angle (θ→0∘\theta \to 0^\circ), the upward component sin⁡θ\sin\theta is very small, meaning TT must be significantly larger than the suspended weight MgMg.

  • Compare TT to the weight Mg≈83.3 NMg \approx 83.3\text{ N}. Since the cable is nearly horizontal, the tension must be much larger than 83.3 N83.3\text{ N}, so 44.7 N44.7\text{ N} should immediately stand out as impossible.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Evaluate sin⁡(1.20∘)\sin(1.20^\circ) in degree mode: sin⁡(1.20∘)≈0.020944\sin(1.20^\circ) \approx 0.020944.

  2. Compute the numerator: Mg=8.50 kg×9.80 m/s2=83.3 NMg = 8.50\text{ kg} \times 9.80\text{ m/s}^2 = 83.3\text{ N}.

  3. Substitute both values into the tension formula: T=83.3 N2×0.020944≈1.99×103 NT = \frac{83.3\text{ N}}{2 \times 0.020944} \approx 1.99 \times 10^3\text{ N}.

Final answer

T(θ)=Mg2sin⁡θT(\theta) = \frac{Mg}{2\sin\theta} (with T→∞T \to \infty as θ→0∘\theta \to 0^\circ); T(1.20∘)=1.99×103 NT(1.20^\circ) = 1.99 \times 10^3\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Switch your calculator to DEG mode whenever working with degree measurements like 1.20∘1.20^\circ.

  • Use the small-angle approximation sin⁡θ≈θrad=1.20×π180≈0.02094\sin\theta \approx \theta_{\text{rad}} = 1.20 \times \frac{\pi}{180} \approx 0.02094 as a mental benchmark to verify small degree sines.

Lock it in

Similar question

01

A traffic light of mass m=15.0 kgm = 15.0\text{ kg} is suspended symmetrically by two cables. Each cable makes an angle of 10.0∘10.0^\circ above the horizontal. Calculate the tension TT in each cable. (Use g=9.80 m/s2g = 9.80\text{ m/s}^2)

Answer

T=423 NT = 423\text{ N}. Key steps: (1) Set vertical equilibrium 2Tsin⁡(10.0∘)=mg2T\sin(10.0^\circ) = mg; (2) Solve T=15.0×9.802sin⁡(10.0∘)=1472(0.1736)≈423 NT = \frac{15.0 \times 9.80}{2\sin(10.0^\circ)} = \frac{147}{2(0.1736)} \approx 423\text{ N}.

02

A tightrope walker of mass M=65.0 kgM = 65.0\text{ kg} stands at the center of a horizontal wire. The wire sags so that each half forms an angle θ=3.50∘\theta = 3.50^\circ below the horizontal. If the wire has a maximum breaking strength of 6.00×103 N6.00\times 10^3\text{ N}, determine whether the wire will snap. (Use g=9.80 m/s2g = 9.80\text{ m/s}^2)

Answer

No, the wire will not snap (T=5.22×103 N<6.00×103 NT = 5.22\times 10^3\text{ N} < 6.00\times 10^3\text{ N}). Key steps: (1) 2Tsin⁡θ=Mg2T\sin\theta = Mg; (2) T=65.0×9.802sin⁡(3.50∘)=6372(0.06105)≈5.22×103 NT = \frac{65.0 \times 9.80}{2\sin(3.50^\circ)} = \frac{637}{2(0.06105)} \approx 5.22\times 10^3\text{ N}.

03

A symmetric hammock is suspended between two trees. The suspension ropes make an angle ϕ\phi with the vertical tree trunks. Express the tension TT in each rope in terms of the total mass MM, gg, and ϕ\phi, and explain what happens to the tension as ϕ→90∘\phi \to 90^\circ.

Answer

T=Mg2cos⁡ϕT = \frac{Mg}{2\cos\phi}; as ϕ→90∘\phi \to 90^\circ, T→∞T \to \infty. Key steps: (1) The vertical component is adjacent to ϕ\phi, so Ty=Tcos⁡ϕT_y = T\cos\phi; (2) Equilibrium gives 2Tcos⁡ϕ=Mg  ⟹  T=Mg2cos⁡ϕ2T\cos\phi = Mg \implies T = \frac{Mg}{2\cos\phi}; (3) As ϕ→90∘\phi \to 90^\circ (rope becomes horizontal), cos⁡ϕ→0\cos\phi \to 0, causing T→∞T \to \infty.

Loading workspace…