Resources

A wooden block of mass M=1.95 kgM = 1.95\text{ kg} is suspended from the ceiling by two vertical, light cords of length L=1.25 mL = 1.25\text{ m}, forming a ballistic pendulum. A small lead bullet of mass m=0.0500 kgm = 0.0500\text{ kg} is fired horizontally into the stationary block with an unknown muzzle speed v0v_0 and becomes completely embedded inside it in an instantaneous horizontal collision. The block-bullet combination then swings upward along an arc, reaching a maximum vertical rise height h=0.180 mh = 0.180\text{ m} above its initial equilibrium height before momentarily stopping. Take g=9.80 m/s2g = 9.80\text{ m/s}^2. (a) Calculate the common velocity VV of the block and embedded bullet immediately after the collision. (b) Calculate the bullet's initial speed v0v_0. (c) Calculate the mechanical energy dissipated as thermal/internal energy during the collision phase.

Answer and steps

Final answer

(a) V=1.88 m/sV = 1.88\text{ m/s}; (b) v0=75.1 m/sv_0 = 75.1\text{ m/s}; (c) ΔEdiss=137 J\Delta E_{\text{diss}} = 137\text{ J} (representing 97.5%97.5\% of initial kinetic energy dissipated).

Steps

The motion of a ballistic pendulum is divided into two distinct, successive stages:

  1. The Collision (Stage 1): A rapid, completely inelastic collision where horizontal linear momentum is conserved, but mechanical energy is not conserved.
  2. The Swing (Stage 2): An upward swing where mechanical energy is conserved under gravity, while external tension forces act perpendicular to the path.

Part (a): Common Velocity Immediately After Collision

During the upward swing from the lowest position to maximum height hh, only gravity does work on the combined bullet-block system (the tension in the cords acts perpendicularly to the trajectory and does zero work).

By conservation of mechanical energy: Ebottom=EtopE_{\text{bottom}} = E_{\text{top}} 12(m+M)V2=(m+M)gh\frac{1}{2}(m + M)V^2 = (m + M)gh

Dividing both sides by the combined mass (m+M)(m + M) and solving for VV: V=2ghV = \sqrt{2gh}

Substitute the given values g=9.80 m/s2g = 9.80\text{ m/s}^2 and h=0.180 mh = 0.180\text{ m}: V=2(9.80 m/s2)(0.180 m)=3.528 m2/s2≈1.88 m/sV = \sqrt{2(9.80\text{ m/s}^2)(0.180\text{ m})} = \sqrt{3.528\text{ m}^2/\text{s}^2} \approx 1.88\text{ m/s}


Part (b): Initial Speed of the Bullet

During the collision, the bullet embeds into the block instantaneously before the pendulum noticeably changes its vertical position. Net external horizontal forces are negligible during this brief impact, so horizontal momentum is conserved: pinitial=pfinalp_{\text{initial}} = p_{\text{final}} mv0=(m+M)Vm v_0 = (m + M)V

Solving for the bullet's initial velocity v0v_0: v0=(m+Mm)Vv_0 = \left(\frac{m + M}{m}\right) V

Substitute m=0.0500 kgm = 0.0500\text{ kg}, M=1.95 kgM = 1.95\text{ kg} (so m+M=2.00 kgm + M = 2.00\text{ kg}), and V≈1.8783 m/sV \approx 1.8783\text{ m/s}: v0=(2.00 kg0.0500 kg)(1.8783 m/s)=40×1.8783 m/s≈75.1 m/sv_0 = \left(\frac{2.00\text{ kg}}{0.0500\text{ kg}}\right)(1.8783\text{ m/s}) = 40 \times 1.8783\text{ m/s} \approx 75.1\text{ m/s}


Part (c): Dissipated Mechanical Energy

Because the collision is completely inelastic, a large fraction of the mechanical energy is dissipated into thermal energy, sound, and the permanent deformation of the wood and bullet.

  1. Initial kinetic energy of the system: Ki=12mv02=12(0.0500 kg)(75.1 m/s)2≈141 JK_i = \frac{1}{2}mv_0^2 = \frac{1}{2}(0.0500\text{ kg})(75.1\text{ m/s})^2 \approx 141\text{ J}
  2. Kinetic energy immediately after the collision: Kf=12(m+M)V2=12(2.00 kg)(1.88 m/s)2≈3.53 JK_f = \frac{1}{2}(m + M)V^2 = \frac{1}{2}(2.00\text{ kg})(1.88\text{ m/s})^2 \approx 3.53\text{ J}

    (Alternatively, Kf=(m+M)gh=2.00×9.80×0.180≈3.53 JK_f = (m+M)gh = 2.00 \times 9.80 \times 0.180 \approx 3.53\text{ J}.)

  3. Energy dissipated (ΔEdiss\Delta E_{\text{diss}}): ΔEdiss=Ki−Kf=141 J−3.53 J≈137 J\Delta E_{\text{diss}} = K_i - K_f = 141\text{ J} - 3.53\text{ J} \approx 137\text{ J}

The fraction of kinetic energy retained is: KfKi=mm+M=0.05002.00=0.025(2.5%)\frac{K_f}{K_i} = \frac{m}{m + M} = \frac{0.0500}{2.00} = 0.025 \quad (2.5\%) Thus, 1−0.025=0.9751 - 0.025 = 0.975 or 97.5%97.5\% of the initial mechanical energy is dissipated.

Common Pitfall: Never apply conservation of kinetic energy across the collision stage. Assuming Ki=KfK_i = K_f is only valid for perfectly elastic collisions; in a ballistic pendulum, the bullet embedding into the target guarantees significant energy loss.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student mistakenly assumes mechanical energy is conserved throughout the entire process including the collision, equating the bullet's initial kinetic energy directly to the maximum gravitational potential energy.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    V=2gh  ⟹  V=2⋅9.80⋅0.180=1.88 m/sV = \sqrt{2gh} \implies V = \sqrt{2 \cdot 9.80 \cdot 0.180} = 1.88\text{ m/s}

  2. Step 2

    12mv02=(m+M)gh  ⟹  v0=2(m+M)ghm=2⋅2.00⋅9.80⋅0.1800.0500=11.9 m/s\frac{1}{2}mv_0^2 = (m+M)gh \implies v_0 = \sqrt{\frac{2(m+M)gh}{m}} = \sqrt{\frac{2 \cdot 2.00 \cdot 9.80 \cdot 0.180}{0.0500}} = 11.9\text{ m/s}

    Correct

    mv0=(m+M)V  ⟹  v0=(m+Mm)V=(2.00 kg0.0500 kg)(1.88 m/s)≈75.1 m/smv_0 = (m+M)V \implies v_0 = \left(\frac{m+M}{m}\right)V = \left(\frac{2.00\text{ kg}}{0.0500\text{ kg}}\right)(1.88\text{ m/s}) \approx 75.1\text{ m/s}

    You equated the initial kinetic energy of the bullet directly to the final potential energy. Because the bullet embeds in the target, this is a completely inelastic collision where mechanical energy is not conserved. You must use conservation of momentum across the impact stage: mv0=(m+M)Vmv_0 = (m+M)V.

  3. Step 3

    ΔE=12mv02−(m+M)gh  ⟹  ΔE=0 J\Delta E = \frac{1}{2}mv_0^2 - (m+M)gh \implies \Delta E = 0\text{ J}

    Correct

    ΔEdiss=12mv02−12(m+M)V2≈141 J−3.53 J=137 J\Delta E_{\text{diss}} = \frac{1}{2}mv_0^2 - \frac{1}{2}(m+M)V^2 \approx 141\text{ J} - 3.53\text{ J} = 137\text{ J}

    Because of the previous assumption that mechanical energy was conserved, your calculated energy loss evaluated to zero. In reality, 137 J137\text{ J} of kinetic energy is converted into thermal and internal energy during the embedding process.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that gravity is the only force doing work during the swing phase.

You accurately calculated the post-collision velocity of the combined system as V=1.88 m/sV = 1.88\text{ m/s}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inelastic collision treated as energy-conserving

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the entire ballistic pendulum sequence as a single continuous energy-conserving event, overlooking the fact that completely inelastic collisions (where objects stick together) inherently convert a large portion of mechanical energy into non-mechanical forms.

REASONING PATH
Your ACEpath teacher’s suggested approach
Split the Problem into Two Distinct Stages
  • A ballistic pendulum consists of: (1) Collision phase (conservation of linear momentum applies, mechanical energy is lost), followed by (2) Swing phase (conservation of mechanical energy applies, momentum is not conserved due to external net forces).

  • Never equate the pre-collision kinetic energy of a projectile directly to the post-collision potential energy when an inelastic impact occurs.

Calculate Energy Dissipated Across Inelastic Impacts
  • ΔEdiss=Kinitial−Kfinal=12mv02−12(m+M)V2\Delta E_{\text{diss}} = K_{\text{initial}} - K_{\text{final}} = \frac{1}{2}mv_0^2 - \frac{1}{2}(m+M)V^2.

  • Compute the kinetic energy immediately before and immediately after impact using the velocities found from momentum conservation.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply conservation of horizontal momentum across the instantaneous collision: mv0=(m+M)Vm v_0 = (m + M)V.

  2. Solve for the initial bullet speed: v0=m+MmV=2.00 kg0.0500 kg×1.8783 m/s≈75.1 m/sv_0 = \frac{m + M}{m}V = \frac{2.00\text{ kg}}{0.0500\text{ kg}} \times 1.8783\text{ m/s} \approx 75.1\text{ m/s}.

  3. Compute the initial kinetic energy: Ki=12mv02=12(0.0500 kg)(75.13 m/s)2≈141.1 JK_i = \frac{1}{2}mv_0^2 = \frac{1}{2}(0.0500\text{ kg})(75.13\text{ m/s})^2 \approx 141.1\text{ J}.

  4. Compute the mechanical energy immediately after collision: Kf=12(m+M)V2=(m+M)gh=2.00 kg×9.80 m/s2×0.180 m≈3.53 JK_f = \frac{1}{2}(m+M)V^2 = (m+M)gh = 2.00\text{ kg} \times 9.80\text{ m/s}^2 \times 0.180\text{ m} \approx 3.53\text{ J}.

  5. Calculate the energy dissipated: ΔEdiss=Ki−Kf=141.1 J−3.53 J≈137 J\Delta E_{\text{diss}} = K_i - K_f = 141.1\text{ J} - 3.53\text{ J} \approx 137\text{ J}.

Final answer

(a) V=1.88 m/sV = 1.88\text{ m/s}; (b) v0=75.1 m/sv_0 = 75.1\text{ m/s}; (c) ΔEdiss=137 J\Delta E_{\text{diss}} = 137\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between elastic collisions (where kinetic energy is conserved) and inelastic collisions (where kinetic energy is lost).

  • Practice identifying the two separate stages of ballistic pendulum problems before writing any equations.

  • Work through the flashcards and practice problems below to master momentum conservation during impacts.

OverviewACEpath Teacher's Diagnosis

02 The student neglects the bullet's mass embedded in the block after collision, using M instead of (m + M) in the momentum conservation equation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    V=2gh  ⟹  V=2×9.80×0.180=1.88 m/sV = \sqrt{2gh} \implies V = \sqrt{2 \times 9.80 \times 0.180} = 1.88\text{ m/s}

  2. Step 2

    mv0=MV  ⟹  v0=(Mm)V  ⟹  v0=(1.950.0500)(1.88)=39×1.88=73.3 m/smv_0 = MV \implies v_0 = \left(\frac{M}{m}\right)V \implies v_0 = \left(\frac{1.95}{0.0500}\right)(1.88) = 39 \times 1.88 = 73.3\text{ m/s}

    Correct

    mv0=(m+M)V  ⟹  v0=(m+Mm)V=(2.00 kg0.0500 kg)(1.878 m/s)≈75.1 m/smv_0 = (m + M)V \implies v_0 = \left(\frac{m + M}{m}\right)V = \left(\frac{2.00\text{ kg}}{0.0500\text{ kg}}\right)(1.878\text{ m/s}) \approx 75.1\text{ m/s}

    Because the bullet embeds into the block, the total mass moving at speed VV immediately after impact is (m+M)(m + M), not just MM. The mass ratio should be m+Mm=40\frac{m+M}{m} = 40 rather than 3939.

  3. Step 3

    Ek0=12(0.0500)(73.3)2=134.3 J  ⟹  Ek1=12(1.95)(1.88)2=3.45 J  ⟹  ΔE=134.3−3.45=130.9 JE_{k_0} = \frac{1}{2}(0.0500)(73.3)^2 = 134.3\text{ J} \implies E_{k_1} = \frac{1}{2}(1.95)(1.88)^2 = 3.45\text{ J} \implies \Delta E = 134.3 - 3.45 = 130.9\text{ J}

    Correct

    ΔEdiss=12mv02−12(m+M)V2=141.0 J−3.53 J≈137 J\Delta E_{\text{diss}} = \frac{1}{2}mv_0^2 - \frac{1}{2}(m + M)V^2 = 141.0\text{ J} - 3.53\text{ J} \approx 137\text{ J}

    Your subtraction method is correct, but your answer is affected by using v0=73.3 m/sv_0 = 73.3\text{ m/s} and omitting mm from the post-collision kinetic energy 12(m+M)V2\frac{1}{2}(m+M)V^2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that the swing phase conserves mechanical energy and solved for VV using V=2ghV = \sqrt{2gh}.

You recognized that linear momentum is conserved horizontally during the brief collision.

You correctly set up the energy dissipated as the difference between initial and post-collision kinetic energy.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of embedded projectile mass in completely inelastic collision

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the post-collision body as having only the target mass MM rather than the combined system mass (m+M)(m + M), forgetting to account for the embedded bullet inside the block.

REASONING PATH
Your ACEpath teacher’s suggested approach
Completely Inelastic Collision Mass
  • When an object of mass mm embeds into a target of mass MM, they stick together and move as a single combined mass mtotal=m+Mm_{\text{total}} = m + M.

  • Always write the final momentum as (m+M)V(m + M)V and the post-collision kinetic energy as 12(m+M)V2\frac{1}{2}(m + M)V^2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply conservation of horizontal momentum with the combined mass: mv0=(m+M)Vm v_0 = (m + M)V.

  2. Substitute the total mass: v0=(0.0500+1.950.0500)(1.8783 m/s)=40×1.8783 m/s≈75.1 m/sv_0 = \left(\frac{0.0500 + 1.95}{0.0500}\right)(1.8783\text{ m/s}) = 40 \times 1.8783\text{ m/s} \approx 75.1\text{ m/s}.

  3. Calculate initial kinetic energy: Ki=12mv02=12(0.0500 kg)(75.13 m/s)2≈141.1 JK_i = \frac{1}{2}mv_0^2 = \frac{1}{2}(0.0500\text{ kg})(75.13\text{ m/s})^2 \approx 141.1\text{ J}.

  4. Calculate post-collision kinetic energy: Kf=12(m+M)V2=12(2.00 kg)(1.8783 m/s)2≈3.53 JK_f = \frac{1}{2}(m + M)V^2 = \frac{1}{2}(2.00\text{ kg})(1.8783\text{ m/s})^2 \approx 3.53\text{ J}.

  5. Compute dissipated energy: ΔEdiss=Ki−Kf=141.1 J−3.53 J≈137 J\Delta E_{\text{diss}} = K_i - K_f = 141.1\text{ J} - 3.53\text{ J} \approx 137\text{ J}.

Final answer

(a) V=1.88 m/sV = 1.88\text{ m/s}; (b) v0=75.1 m/sv_0 = 75.1\text{ m/s}; (c) ΔEdiss=137 J\Delta E_{\text{diss}} = 137\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the definition of completely inelastic collisions: when two masses stick together, the resulting object has mass m1+m2m_1 + m_2.

  • Practice checking whether any mass was added to or ejected from the system before writing the momentum conservation expression.

OverviewACEpath Teacher's Diagnosis

03 The student confuses the cord length L with the vertical rise height h when computing the post-collision velocity.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    V=2gL  ⟹  V=2⋅9.80⋅1.25=24.5=4.95 m/sV = \sqrt{2gL} \implies V = \sqrt{2 \cdot 9.80 \cdot 1.25} = \sqrt{24.5} = 4.95\text{ m/s}

    Correct

    V=2gh=2(9.80 m/s2)(0.180 m)≈1.88 m/sV = \sqrt{2gh} = \sqrt{2(9.80\text{ m/s}^2)(0.180\text{ m})} \approx 1.88\text{ m/s}

    You used the cord length L=1.25 mL = 1.25\text{ m} instead of the maximum vertical rise height h=0.180 mh = 0.180\text{ m}. In conservation of mechanical energy for the swing, the potential energy gain depends solely on the vertical elevation change Δy=h\Delta y = h, not the length of the string.

  2. Step 2

    mv0=(m+M)V  ⟹  v0=(0.0500+1.950.0500)⋅4.95=40⋅4.95=198 m/smv_0 = (m+M)V \implies v_0 = \left(\frac{0.0500 + 1.95}{0.0500}\right) \cdot 4.95 = 40 \cdot 4.95 = 198\text{ m/s}

    Correct

    v0=(m+Mm)V=40×1.8783 m/s≈75.1 m/sv_0 = \left(\frac{m+M}{m}\right)V = 40 \times 1.8783\text{ m/s} \approx 75.1\text{ m/s}

    Your momentum conservation setup and mass ratio evaluation are completely correct. The resulting numerical value is affected solely by substituting V=4.95 m/sV = 4.95\text{ m/s} from Step 1.

  3. Step 3

    Ek0=12⋅0.0500⋅(198)2=980.1 J  ⟹  Ek1=12⋅2.00⋅(4.95)2=24.5 J  ⟹  ΔE=980.1−24.5=955.6 JE_{k0} = \frac{1}{2} \cdot 0.0500 \cdot (198)^2 = 980.1\text{ J} \implies E_{k1} = \frac{1}{2} \cdot 2.00 \cdot (4.95)^2 = 24.5\text{ J} \implies \Delta E = 980.1 - 24.5 = 955.6\text{ J}

    Correct

    Ki=12(0.0500)(75.1)2≈141 J  ⟹  Kf=12(2.00)(1.88)2≈3.53 J  ⟹  ΔEdiss=141 J−3.53 J≈137 JK_i = \frac{1}{2}(0.0500)(75.1)^2 \approx 141\text{ J} \implies K_f = \frac{1}{2}(2.00)(1.88)^2 \approx 3.53\text{ J} \implies \Delta E_{\text{diss}} = 141\text{ J} - 3.53\text{ J} \approx 137\text{ J}

    Your method of finding energy lost by subtracting post-collision kinetic energy from initial kinetic energy is perfectly valid. The numerical answer is affected by your earlier speeds.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that linear momentum is conserved during the brief horizontal collision.

You properly applied the mass ratio (m+M)/m=40(m+M)/m = 40 to relate post-collision speed to bullet speed.

You correctly identified that mechanical energy is dissipated during the collision and computed ΔE\Delta E as Ki−KfK_i - K_f.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Parameter substitution error: confusing cord length with vertical rise height

You plugged the pendulum length LL into 2gh\sqrt{2gh} where the vertical rise height hh was required.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

In pendulum problems, students often see a length given in meters and instinctively insert it into v=2ghv = \sqrt{2gh}. Gravitational potential energy change depends strictly on the vertical coordinate shift Δy=h\Delta y = h, whereas cord length LL only enters if you must calculate hh from a swing angle via h=L(1−cos⁡θ)h = L(1 - \cos\theta).

REASONING PATH
Your ACEpath teacher’s suggested approach
Gravitational Height vs. Cord Length
  • In ΔUg=mgΔy\Delta U_g = mg\Delta y, Δy=h\Delta y = h is the vertical elevation reached above the release or bottom point, never the length of the suspending cord.

  • Always draw a quick diagram marking the equilibrium line and label the vertical rise hh separately from the pendulum length LL.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate the post-collision speed using the vertical rise height h=0.180 mh = 0.180\text{ m}: V=2gh=2(9.80)(0.180)=3.528≈1.88 m/sV = \sqrt{2gh} = \sqrt{2(9.80)(0.180)} = \sqrt{3.528} \approx 1.88\text{ m/s}.

  2. Apply horizontal momentum conservation with the corrected VV: v0=40×1.8783 m/s≈75.1 m/sv_0 = 40 \times 1.8783\text{ m/s} \approx 75.1\text{ m/s}.

  3. Recalculate the dissipated energy: Ki=12(0.0500)(75.13)2≈141.1 JK_i = \frac{1}{2}(0.0500)(75.13)^2 \approx 141.1\text{ J}, Kf=12(2.00)(1.8783)2≈3.53 JK_f = \frac{1}{2}(2.00)(1.8783)^2 \approx 3.53\text{ J}, giving ΔEdiss=141.1−3.53≈137.6 J≈137 J\Delta E_{\text{diss}} = 141.1 - 3.53 \approx 137.6\text{ J} \approx 137\text{ J}.

Final answer

(a) V=1.88 m/sV = 1.88\text{ m/s}; (b) v0=75.1 m/sv_0 = 75.1\text{ m/s}; (c) ΔEdiss=137 J\Delta E_{\text{diss}} = 137\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Before substituting numerical values into energy conservation, verify whether a given length is the cord length LL or the vertical displacement hh.

  • Review how pendulum geometry connects angle θ\theta, length LL, and height hh using h=L(1−cos⁡θ)h = L(1 - \cos\theta) when height is not given directly.

Lock it in

Similar question

01

A 0.020 kg0.020\text{ kg} wad of clay traveling horizontally at 15 m/s15\text{ m/s} strikes and sticks to a stationary 0.480 kg0.480\text{ kg} block resting on a frictionless table. (a) Find the speed of the clay-block combination immediately after impact. (b) How much kinetic energy is lost in the collision?

Answer

(a) v=0.60 m/sv = 0.60\text{ m/s}; (b) ΔKloss=2.16 J\Delta K_{\text{loss}} = 2.16\text{ J}. Key steps: By momentum conservation, mv0=(m+M)v  ⟹  (0.020)(15)=(0.500)v  ⟹  v=0.60 m/sm v_0 = (m+M)v \implies (0.020)(15) = (0.500)v \implies v = 0.60\text{ m/s}. Ki=12(0.020)(15)2=2.25 JK_i = \frac{1}{2}(0.020)(15)^2 = 2.25\text{ J}. Kf=12(0.500)(0.60)2=0.090 JK_f = \frac{1}{2}(0.500)(0.60)^2 = 0.090\text{ J}. ΔK=2.25−0.090=2.16 J\Delta K = 2.25 - 0.090 = 2.16\text{ J}.

02

A dart of mass m=40.0 gm = 40.0\text{ g} is shot horizontally into a stationary wooden pendulum bob of mass M=360.0 gM = 360.0\text{ g}. After the dart embeds itself, the pendulum swings up to a vertical height of h=0.450 mh = 0.450\text{ m}. Calculate the dart's initial speed v0v_0. (Take g=9.80 m/s2g = 9.80\text{ m/s}^2)

Answer

v0=29.7 m/sv_0 = 29.7\text{ m/s}. Key steps: During the swing, energy is conserved: V=2gh=2(9.80)(0.450)=2.97 m/sV = \sqrt{2gh} = \sqrt{2(9.80)(0.450)} = 2.97\text{ m/s}. During the collision, momentum is conserved: mv0=(m+M)V  ⟹  v0=0.040+0.3600.040×2.97=10×2.97=29.7 m/sm v_0 = (m+M)V \implies v_0 = \frac{0.040 + 0.360}{0.040} \times 2.97 = 10 \times 2.97 = 29.7\text{ m/s}.

03

In a ballistic pendulum experiment, a bullet of mass mm hits a block of mass MM and embeds inside it. Express the fraction of initial kinetic energy lost during the collision, ΔKKi\frac{\Delta K}{K_i}, purely in terms of the masses mm and MM. What happens to this fraction if M≫mM \gg m?

Answer

Fraction lost =Mm+M= \frac{M}{m+M}. If M≫mM \gg m, the fraction approaches 11 (nearly 100%100\% of kinetic energy is lost). Key steps: V=mm+Mv0V = \frac{m}{m+M}v_0. Kf=12(m+M)V2=12(m+M)(mm+Mv0)2=mm+M(12mv02)=(mm+M)KiK_f = \frac{1}{2}(m+M)V^2 = \frac{1}{2}(m+M)\left(\frac{m}{m+M}v_0\right)^2 = \frac{m}{m+M}\left(\frac{1}{2}mv_0^2\right) = \left(\frac{m}{m+M}\right)K_i. Therefore, ΔKKi=1−mm+M=Mm+M\frac{\Delta K}{K_i} = 1 - \frac{m}{m+M} = \frac{M}{m+M}.

Loading workspace…