Resources

A heat engine operates on a closed thermodynamic cycle using n=0.0400 moln = 0.0400\text{ mol} of an ideal monatomic gas (CV=32RC_V = \frac{3}{2}R). The cycle consists of three sequential processes: Step 1→21 \to 2 is an isobaric expansion at constant pressure P1=2.00×105 PaP_1 = 2.00 \times 10^5\text{ Pa} from volume V1=5.00×10−4 m3V_1 = 5.00 \times 10^{-4}\text{ m}^3 to V2=1.20×10−3 m3V_2 = 1.20 \times 10^{-3}\text{ m}^3; Step 2→32 \to 3 is an isochoric depressurization at constant volume V2V_2 down to P3=1.00×105 PaP_3 = 1.00 \times 10^5\text{ Pa}; Step 3→13 \to 1 is a direct linear return path along a straight line on the PP-VV indicator diagram back to state (P1,V1)(P_1, V_1). Determine: (a) the net mechanical work WnetW_{\text{net}} performed by the gas over one cycle, (b) the total heat input QinQ_{\text{in}} absorbed during the heating phase, and (c) the cycle efficiency η\eta.

Answer and steps

Final answer

(a) Wnet=35.0 JW_{\text{net}} = 35.0\text{ J}; (b) Qin=350 JQ_{\text{in}} = 350\text{ J}; (c) η=0.100\eta = 0.100 (or 10.0%10.0\%).

Steps

01

Calculate the net mechanical work (WnetW_{\text{net}})

On a pressure-volume (PP-VV) diagram, the net work performed by a system over a closed cyclic process equals the area enclosed by the path:

  • The cycle runs clockwise along the vertices (V1,P1)(V_1, P_1), (V2,P1)(V_2, P_1), and (V2,P3)(V_2, P_3), which form a right-angled triangle.
  • A clockwise path does positive net work.

The base and height of this right triangle are: ΔV=V2−V1=1.20×10−3 m3−5.00×10−4 m3=0.70×10−3 m3\Delta V = V_2 - V_1 = 1.20 \times 10^{-3}\text{ m}^3 - 5.00 \times 10^{-4}\text{ m}^3 = 0.70 \times 10^{-3}\text{ m}^3 ΔP=P1−P3=2.00×105 Pa−1.00×105 Pa=1.00×105 Pa\Delta P = P_1 - P_3 = 2.00 \times 10^5\text{ Pa} - 1.00 \times 10^5\text{ Pa} = 1.00 \times 10^5\text{ Pa}

The enclosed area gives the net work: Wnet=12ΔVΔP=12(0.70×10−3 m3)(1.00×105 Pa)=35.0 JW_{\text{net}} = \frac{1}{2} \Delta V \Delta P = \frac{1}{2}(0.70 \times 10^{-3}\text{ m}^3)(1.00 \times 10^5\text{ Pa}) = 35.0\text{ J}


02

Identify the heating phase and find QinQ_{\text{in}}

To find the heat absorbed by the engine, evaluate the heat exchange for each of the three steps using the First Law of Thermodynamics, Q=ΔU+WQ = \Delta U + W:

  1. Step 1→21 \to 2 (Isobaric expansion at P1=2.00×105 PaP_1 = 2.00 \times 10^5\text{ Pa}): For an ideal monatomic gas, the molar heat capacity at constant pressure is: CP=CV+R=32R+R=52RC_P = C_V + R = \frac{3}{2}R + R = \frac{5}{2}R Using the ideal gas equation of state (PΔV=nRΔTP \Delta V = n R \Delta T): Q1→2=nCPΔT=52P1(V2−V1)Q_{1\to 2} = n C_P \Delta T = \frac{5}{2} P_1 (V_2 - V_1) Q1→2=52(2.00×105 Pa)(0.70×10−3 m3)=350 JQ_{1\to 2} = \frac{5}{2}(2.00 \times 10^5\text{ Pa})(0.70 \times 10^{-3}\text{ m}^3) = 350\text{ J} Since Q1→2>0Q_{1\to 2} > 0, heat is absorbed in this step.
  2. Step 2→32 \to 3 (Isochoric depressurization at V2=1.20×10−3 m3V_2 = 1.20 \times 10^{-3}\text{ m}^3): Because volume is constant, W2→3=0W_{2\to 3} = 0: Q2→3=nCVΔT=32V2(P3−P2)Q_{2\to 3} = n C_V \Delta T = \frac{3}{2} V_2 (P_3 - P_2) Q2→3=32(1.20×10−3 m3)(1.00×105 Pa−2.00×105 Pa)=−180 JQ_{2\to 3} = \frac{3}{2}(1.20 \times 10^{-3}\text{ m}^3)(1.00 \times 10^5\text{ Pa} - 2.00 \times 10^5\text{ Pa}) = -180\text{ J} Since Q2→3<0Q_{2\to 3} < 0, heat is expelled to the cold reservoir.
  3. Step 3→13 \to 1 (Linear compression from (V2,P3)(V_2, P_3) to (V1,P1)(V_1, P_1)):

    • Change in internal energy: ΔU3→1=32(P1V1−P3V2)=32[(2.00×105)(5.00×10−4)−(1.00×105)(1.20×10−3)]=32(100−120)=−30 J\Delta U_{3\to 1} = \frac{3}{2}(P_1 V_1 - P_3 V_2) = \frac{3}{2}\left[(2.00 \times 10^5)(5.00 \times 10^{-4}) - (1.00 \times 10^5)(1.20 \times 10^{-3})\right] = \frac{3}{2}(100 - 120) = -30\text{ J}
    • Work done by the gas (area under the linear segment, negative because the gas is compressed): W3→1=−P1+P32(V2−V1)=−2.00×105+1.00×1052(0.70×10−3)=−105 JW_{3\to 1} = -\frac{P_1 + P_3}{2}(V_2 - V_1) = -\frac{2.00 \times 10^5 + 1.00 \times 10^5}{2}(0.70 \times 10^{-3}) = -105\text{ J}
    • Heat transfer: Q3→1=ΔU3→1+W3→1=−30 J−105 J=−135 JQ_{3\to 1} = \Delta U_{3\to 1} + W_{3\to 1} = -30\text{ J} - 105\text{ J} = -135\text{ J} Since Q3→1<0Q_{3\to 1} < 0, heat is also released during this step.

Thus, heat input occurs exclusively during Step 1→21 \to 2: Qin=Q1→2=350 JQ_{\text{in}} = Q_{1\to 2} = 350\text{ J}

(Self-check: Qnet=350 J−180 J−135 J=35.0 J=WnetQ_{\text{net}} = 350\text{ J} - 180\text{ J} - 135\text{ J} = 35.0\text{ J} = W_{\text{net}}, which satisfies energy conservation over a complete cycle.)


03

Compute the thermal efficiency (η\eta)

The thermal efficiency of a heat engine is the ratio of useful net work output to the total heat input absorbed: η=WnetQin=35.0 J350 J=0.100(or 10.0%)\eta = \frac{W_{\text{net}}}{Q_{\text{in}}} = \frac{35.0\text{ J}}{350\text{ J}} = 0.100\quad (\text{or } 10.0\%)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misidentifies the heat capacity for an isobaric process by using C_V = (3/2)R instead of C_p = (5/2)R, resulting in an underestimated heat input of 210 J and an overestimated efficiency of 16.7%.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Wnet=12×(P1−P3)×(V2−V1)  ⟹  Wnet=0.5×(1.00×105 Pa)×(7.00×10−4 m3)=35.0 JW_{\text{net}} = \frac{1}{2} \times (P_1 - P_3) \times (V_2 - V_1) \implies W_{\text{net}} = 0.5 \times (1.00 \times 10^5\text{ Pa}) \times (7.00 \times 10^{-4}\text{ m}^3) = 35.0\text{ J}

  2. Step 2

    Qin=Q12=n×CV×ΔT=(32)×P1×(V2−V1)  ⟹  Qin=(32)×(2.00×105 Pa)×(7.00×10−4 m3)=210 JQ_{\text{in}} = Q_{12} = n \times C_V \times \Delta T = \left(\frac{3}{2}\right) \times P_1 \times (V_2 - V_1) \implies Q_{\text{in}} = \left(\frac{3}{2}\right) \times (2.00 \times 10^5\text{ Pa}) \times (7.00 \times 10^{-4}\text{ m}^3) = 210\text{ J}

    Correct

    Qin=Q1→2=nCPΔT=52P1(V2−V1)=52(2.00×105 Pa)(0.70×10−3 m3)=350 JQ_{\text{in}} = Q_{1\to 2} = n C_P \Delta T = \frac{5}{2} P_1 (V_2 - V_1) = \frac{5}{2}(2.00 \times 10^5\text{ Pa})(0.70 \times 10^{-3}\text{ m}^3) = 350\text{ J}

    Process 1→21 \to 2 is an isobaric (constant-pressure) expansion, so heat transfer is Q=nCPΔT=ΔU+WQ = n C_P \Delta T = \Delta U + W. Using CV=32RC_V = \frac{3}{2}R accounts only for the change in internal energy ΔU=210 J\Delta U = 210\text{ J}, omitting the expansion work W1→2=P1ΔV=140 JW_{1\to 2} = P_1 \Delta V = 140\text{ J}.

  3. Step 3

    η=WnetQin=35.0 J210 J=0.167\eta = \frac{W_{\text{net}}}{Q_{\text{in}}} = \frac{35.0\text{ J}}{210\text{ J}} = 0.167

    Correct

    η=WnetQin=35.0 J350 J=0.100 (or 10.0%)\eta = \frac{W_{\text{net}}}{Q_{\text{in}}} = \frac{35.0\text{ J}}{350\text{ J}} = 0.100\text{ (or } 10.0\%)

    Your efficiency formula is correct, but the numerical answer is incorrect due to your previous value for QinQ_{\text{in}}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the enclosed area on the PP-VV diagram as the net work of the thermodynamic cycle.

You accurately converted and evaluated the pressure difference and volume change to obtain Wnet=35.0 JW_{\text{net}} = 35.0\text{ J}.

You correctly related efficiency to the ratio of net work output to total heat input.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Wrong heat capacity for isobaric process

You substituted CV=32RC_V = \frac{3}{2}R instead of CP=52RC_P = \frac{5}{2}R when computing heat added along an isobaric expansion.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing internal energy change ΔU\Delta U with total heat transfer QQ during a constant-pressure process. For an ideal gas, ΔU=nCVΔT\Delta U = n C_V \Delta T applies to every process, but heat transfer QQ equals nCPΔT=ΔU+PΔVn C_P \Delta T = \Delta U + P\Delta V when pressure is held constant.

REASONING PATH
Your ACEpath teacher’s suggested approach
Isobaric Heat vs. Internal Energy
  • For an ideal gas, ΔU=nCVΔT\Delta U = n C_V \Delta T always, but for an isobaric process Q=ΔU+W=n(CV+R)ΔT=nCPΔTQ = \Delta U + W = n(C_V + R)\Delta T = n C_P \Delta T.

  • Always check whether boundary work is done; if volume expands at constant pressure, you must include PΔVP\Delta V in the heat input.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate QinQ_{\text{in}} using CP=CV+R=52RC_P = C_V + R = \frac{5}{2}R: Qin=52P1ΔV=52(2.00×105 Pa)(0.70×10−3 m3)=350 JQ_{\text{in}} = \frac{5}{2} P_1 \Delta V = \frac{5}{2}(2.00 \times 10^5\text{ Pa})(0.70 \times 10^{-3}\text{ m}^3) = 350\text{ J}.

  2. Re-evaluate the thermal efficiency: η=WnetQin=35.0 J350 J=0.100\eta = \frac{W_{\text{net}}}{Q_{\text{in}}} = \frac{35.0\text{ J}}{350\text{ J}} = 0.100.

Final answer

(a) Wnet=35.0 JW_{\text{net}} = 35.0\text{ J}; (b) Qin=350 JQ_{\text{in}} = 350\text{ J}; (c) η=0.100\eta = 0.100 (or 10.0%10.0\%)

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice separating QQ into ΔU+W\Delta U + W for every process segment in a thermodynamic cycle.

  • Review Mayer's relation CP=CV+RC_P = C_V + R for monatomic and diatomic gases.

OverviewACEpath Teacher's Diagnosis

02 The student confuses total heat input with the sum of all heat changes around the cycle, equating Q_in to W_net and incorrectly calculating efficiency as 100%.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Wnet=12(P1−P3)(V2−V1)  ⟹  Wnet=0.5×(1.00×105 Pa)×(7.00×10−4 m3)=35.0 JW_{\text{net}} = \frac{1}{2}(P_1 - P_3)(V_2 - V_1) \implies W_{\text{net}} = 0.5 \times (1.00 \times 10^5\text{ Pa}) \times (7.00 \times 10^{-4}\text{ m}^3) = 35.0\text{ J}

  2. Step 2

    Qnet=Wnet=35.0 JQ_{\text{net}} = W_{\text{net}} = 35.0\text{ J}

  3. Step 3

    Qin=Qnet=35.0 JQ_{\text{in}} = Q_{\text{net}} = 35.0\text{ J}

    Correct

    Qin=Q1→2=nCPΔT=52P1(V2−V1)=350 JQ_{\text{in}} = Q_{1\to 2} = n C_P \Delta T = \frac{5}{2} P_1 (V_2 - V_1) = 350\text{ J}

    You equated heat input QinQ_{\text{in}} to net heat QnetQ_{\text{net}}. In a heat engine, Qnet=Qin−∣Qout∣Q_{\text{net}} = Q_{\text{in}} - |Q_{\text{out}}|. To determine QinQ_{\text{in}}, you must find the heat exchanged in each step and sum only the positive contributions (Q>0Q > 0), which occurs only during the isobaric expansion 1→21 \to 2.

  4. Step 4

    η=WnetQin=35.0 J35.0 J=1.00\eta = \frac{W_{\text{net}}}{Q_{\text{in}}} = \frac{35.0\text{ J}}{35.0\text{ J}} = 1.00

    Correct

    η=WnetQin=35.0 J350 J=0.100 (or 10.0%)\eta = \frac{W_{\text{net}}}{Q_{\text{in}}} = \frac{35.0\text{ J}}{350\text{ J}} = 0.100\text{ (or } 10.0\%)

    You used the correct efficiency formula η=WnetQin\eta = \frac{W_{\text{net}}}{Q_{\text{in}}}, but substituting the incorrect value of QinQ_{\text{in}} yielded an unphysical 100%100\% efficiency.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the net work accurately by determining the area of the enclosed triangular cycle on the PP-VV indicator diagram.

You correctly recognized that for any closed thermodynamic cycle, the net heat equals the net work because the net change in internal energy is zero.

You applied the standard definition of thermal efficiency η=WnetQin\eta = \frac{W_{\text{net}}}{Q_{\text{in}}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Confusing net heat with heat input

You set QinQ_{\text{in}} equal to QnetQ_{\text{net}} instead of evaluating the heat absorbed along individual process segments where Q>0Q > 0.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the net heat exchanged over the entire cycle (Qnet=Qin−∣Qout∣Q_{\text{net}} = Q_{\text{in}} - |Q_{\text{out}}|) with the gross heat input absorbed from the hot reservoir (QinQ_{\text{in}}), overlooking the Second Law constraint that a cyclic engine must reject heat to a cold reservoir.

REASONING PATH
Your ACEpath teacher’s suggested approach
Distinguish Net Heat from Heat Input
  • Qnet=∮δQ=Qin−∣Qout∣=WnetQ_{\text{net}} = \oint \delta Q = Q_{\text{in}} - |Q_{\text{out}}| = W_{\text{net}}. The input heat QinQ_{\text{in}} is the sum of only positive heat steps: Qin=∑Qi>0QiQ_{\text{in}} = \sum_{Q_i > 0} Q_i.

  • Always evaluate Q=ΔU+WQ = \Delta U + W for every process segment separately, and sum only the positive QQ values to find QinQ_{\text{in}}.

Sanity Check Cycle Efficiency
  • By the Kelvin-Planck statement of the Second Law of Thermodynamics, no cyclic heat engine can convert all absorbed heat into work; thus, η<1\eta < 1 (or <100%< 100\%).

  • If your calculated efficiency is 1.001.00 (100%100\%), pause immediately: you have likely substituted QnetQ_{\text{net}} or WnetW_{\text{net}} in place of QinQ_{\text{in}}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Evaluate heat for isobaric expansion 1→21 \to 2: with CP=52RC_P = \frac{5}{2}R, Q1→2=52P1(V2−V1)=52(2.00×105 Pa)(0.70×10−3 m3)=350 J>0Q_{1\to 2} = \frac{5}{2}P_1(V_2 - V_1) = \frac{5}{2}(2.00 \times 10^5\text{ Pa})(0.70 \times 10^{-3}\text{ m}^3) = 350\text{ J} > 0.

  2. Evaluate isochoric depressurization 2→32 \to 3: W2→3=0W_{2\to 3} = 0, so Q2→3=32V2(P3−P2)=32(1.20×10−3 m3)(−1.00×105 Pa)=−180 J<0Q_{2\to 3} = \frac{3}{2}V_2(P_3 - P_2) = \frac{3}{2}(1.20 \times 10^{-3}\text{ m}^3)(-1.00 \times 10^5\text{ Pa}) = -180\text{ J} < 0.

  3. Evaluate linear compression 3→13 \to 1: ΔU3→1=32(P1V1−P3V2)=−30 J\Delta U_{3\to 1} = \frac{3}{2}(P_1 V_1 - P_3 V_2) = -30\text{ J} and W3→1=−P1+P32(V2−V1)=−105 JW_{3\to 1} = -\frac{P_1 + P_3}{2}(V_2 - V_1) = -105\text{ J}, giving Q3→1=−135 J<0Q_{3\to 1} = -135\text{ J} < 0.

  4. Identify positive heat contributions: heat is added only along path 1→21 \to 2, so Qin=350 JQ_{\text{in}} = 350\text{ J}.

  5. Recalculate efficiency: η=WnetQin=35.0 J350 J=0.100\eta = \frac{W_{\text{net}}}{Q_{\text{in}}} = \frac{35.0\text{ J}}{350\text{ J}} = 0.100 (or 10.0%10.0\%).

Final answer

(a) Wnet=35.0 JW_{\text{net}} = 35.0\text{ J}; (b) Qin=350 JQ_{\text{in}} = 350\text{ J}; (c) η=0.100\eta = 0.100 (or 10.0%10.0\%)

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice computing ΔU\Delta U, WW, and QQ step-by-step for each stage of a cyclic process to sort heat into QinQ_{\text{in}} and QoutQ_{\text{out}}.

  • Use the energy-conservation identity Qin−∣Qout∣=WnetQ_{\text{in}} - |Q_{\text{out}}| = W_{\text{net}} as an end-of-problem check rather than assuming Qin=WnetQ_{\text{in}} = W_{\text{net}}.

OverviewACEpath Teacher's Diagnosis

03 The student omits the factor of 1/2 when calculating the area of the triangular cycle on the P-V diagram, doubling the work to 70.0 J and yielding an efficiency of 20.0%.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Wnet=(P1−P3)∗(V2−V1)  ⟹  Wnet=(1.00×105 Pa)∗(7.00×10−4 m3)=70.0 JW_{\text{net}} = (P_1 - P_3) * (V_2 - V_1) \implies W_{\text{net}} = (1.00 \times 10^5\text{ Pa}) * (7.00 \times 10^{-4}\text{ m}^3) = 70.0\text{ J}

    Correct

    Wnet=12(P1−P3)(V2−V1)=12(1.00×105 Pa)(7.00×10−4 m3)=35.0 JW_{\text{net}} = \frac{1}{2}(P_1 - P_3)(V_2 - V_1) = \frac{1}{2}(1.00 \times 10^5\text{ Pa})(7.00 \times 10^{-4}\text{ m}^3) = 35.0\text{ J}

    The closed thermodynamic cycle forms a right triangle on the PP-VV diagram with vertices at (V1,P1)(V_1, P_1), (V2,P1)(V_2, P_1), and (V2,P3)(V_2, P_3). The area of a triangle is 12×base×height\frac{1}{2} \times \text{base} \times \text{height}, so you need to include the factor of 12\frac{1}{2}.

  2. Step 2

    Qin=Q12=(52)∗P1∗(V2−V1)  ⟹  Qin=(52)∗(2.00×105 Pa)∗(7.00×10−4 m3)=350 JQ_{\text{in}} = Q_{12} = \left(\frac{5}{2}\right) * P_1 * (V_2 - V_1) \implies Q_{\text{in}} = \left(\frac{5}{2}\right) * (2.00 \times 10^5\text{ Pa}) * (7.00 \times 10^{-4}\text{ m}^3) = 350\text{ J}

  3. Step 3

    η=WnetQin=70.0 J350 J=0.200\eta = \frac{W_{\text{net}}}{Q_{\text{in}}} = \frac{70.0\text{ J}}{350\text{ J}} = 0.200

    Correct

    η=WnetQin=35.0 J350 J=0.100 (or 10.0%)\eta = \frac{W_{\text{net}}}{Q_{\text{in}}} = \frac{35.0\text{ J}}{350\text{ J}} = 0.100\text{ (or } 10.0\%)

    Your definition and formula for thermal efficiency are correct, but substituting your doubled value of Wnet=70.0 JW_{\text{net}} = 70.0\text{ J} led to an incorrect efficiency of 0.2000.200 instead of 0.1000.100.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the isobaric expansion step 1→21 \to 2 as the only heat-addition process in the cycle.

You used the correct heat capacity CP=52RC_P = \frac{5}{2}R for a monatomic ideal gas at constant pressure.

You correctly set up the thermal efficiency definition η=WnetQin\eta = \frac{W_{\text{net}}}{Q_{\text{in}}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Geometric Area Formula Error

You calculated the area of a rectangle rather than the area of a triangle when finding the net work enclosed by the cycle.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the area of a bounding rectangle ΔPΔV\Delta P \Delta V with the area of a triangular thermodynamic cycle 12ΔPΔV\frac{1}{2} \Delta P \Delta V on a PP-VV indicator diagram.

REASONING PATH
Your ACEpath teacher’s suggested approach
Geometry of the Indicator Loop
  • Net cyclic work WnetW_{\text{net}} equals the enclosed area on the PP-VV plane: for a triangle, Area=12×base×height\text{Area} = \frac{1}{2} \times \text{base} \times \text{height}.

  • Sketch the cycle on the PP-VV plane before calculating work, identify the polygon shape, and verify the geometric area formula.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate net work using the triangle area formula: Wnet=12(P1−P3)(V2−V1)=12(1.00×105 Pa)(7.00×10−4 m3)=35.0 JW_{\text{net}} = \frac{1}{2}(P_1 - P_3)(V_2 - V_1) = \frac{1}{2}(1.00 \times 10^5\text{ Pa})(7.00 \times 10^{-4}\text{ m}^3) = 35.0\text{ J}.

  2. Retain your correct heat input: Qin=350 JQ_{\text{in}} = 350\text{ J}.

  3. Recalculate efficiency: η=WnetQin=35.0 J350 J=0.100\eta = \frac{W_{\text{net}}}{Q_{\text{in}}} = \frac{35.0\text{ J}}{350\text{ J}} = 0.100 (or 10.0%10.0\%).

Final answer

(a) Wnet=35.0 JW_{\text{net}} = 35.0\text{ J}; (b) Qin=350 JQ_{\text{in}} = 350\text{ J}; (c) η=0.100\eta = 0.100 (or 10.0%10.0\%)

NEXT STEPS
Final Takeaways from Your Teacher
  • Draw and label the vertices of the closed cycle on a PP-VV diagram to immediately spot whether the boundary forms a rectangle, triangle, or trapezoid.

  • Practice computing work done along individual paths (W1→2+W2→3+W3→1W_{1\to 2} + W_{2\to 3} + W_{3\to 1}) to cross-verify the geometric enclosed area.

Lock it in

Similar question

01

A sample of 0.0200 mol0.0200\text{ mol} of a monatomic ideal gas (CV=32RC_V = \frac{3}{2}R) expands isobarically at P=1.50×105 PaP = 1.50 \times 10^5\text{ Pa} from Vi=2.00×10−4 m3V_i = 2.00 \times 10^{-4}\text{ m}^3 to Vf=6.00×10−4 m3V_f = 6.00 \times 10^{-4}\text{ m}^3. Calculate the work done by the gas WW and the heat absorbed QQ.

Answer

W=PΔV=(1.50×105)(4.00×10−4)=60.0 JW = P\Delta V = (1.50 \times 10^5)(4.00 \times 10^{-4}) = 60.0\text{ J}. Heat absorbed is Q=nCPΔT=52PΔV=52(60.0 J)=150 JQ = n C_P \Delta T = \frac{5}{2}P\Delta V = \frac{5}{2}(60.0\text{ J}) = 150\text{ J}.

02

A heat engine carries a monatomic ideal gas around a right-triangular cycle on a PP-VV diagram: (V0,P0)→(3V0,P0)(V_0, P_0) \to (3V_0, P_0) (isobaric), (3V0,P0)→(3V0,12P0)(3V_0, P_0) \to (3V_0, \frac{1}{2}P_0) (isochoric), and then along a straight line back to (V0,P0)(V_0, P_0). Express the thermal efficiency η\eta as a fraction.

Answer

Net work is the triangle area: Wnet=12(2V0)(12P0)=12P0V0W_{\text{net}} = \frac{1}{2}(2V_0)(\frac{1}{2}P_0) = \frac{1}{2}P_0 V_0. Heat enters only along the isobaric step: Qin=52P0ΔV=52P0(2V0)=5P0V0Q_{\text{in}} = \frac{5}{2}P_0 \Delta V = \frac{5}{2}P_0(2V_0) = 5P_0 V_0. Thus, η=WnetQin=12P0V05P0V0=110=0.100\eta = \frac{W_{\text{net}}}{Q_{\text{in}}} = \frac{\frac{1}{2}P_0 V_0}{5P_0 V_0} = \frac{1}{10} = 0.100 (or 10%10\%).

03

A heat engine operates on a cycle where 1.00 mol1.00\text{ mol} of a diatomic ideal gas (CV=52RC_V = \frac{5}{2}R) expands isobarically at 2.00×105 Pa2.00 \times 10^5\text{ Pa} from 0.010 m30.010\text{ m}^3 to 0.020 m30.020\text{ m}^3, cools isochorically to 1.00×105 Pa1.00 \times 10^5\text{ Pa}, and returns to the initial state via a straight line on a PP-VV plot. Determine the thermal efficiency of this engine.

Answer

Net work is the triangle area: Wnet=12(1.00×105 Pa)(0.010 m3)=500 JW_{\text{net}} = \frac{1}{2}(1.00 \times 10^5\text{ Pa})(0.010\text{ m}^3) = 500\text{ J}. For a diatomic gas, CP=72RC_P = \frac{7}{2}R, so isobaric heat input is Qin=72PΔV=72(2.00×105 Pa)(0.010 m3)=7000 JQ_{\text{in}} = \frac{7}{2}P\Delta V = \frac{7}{2}(2.00 \times 10^5\text{ Pa})(0.010\text{ m}^3) = 7000\text{ J}. Efficiency is η=WnetQin=500 J7000 J=114≈0.0714\eta = \frac{W_{\text{net}}}{Q_{\text{in}}} = \frac{500\text{ J}}{7000\text{ J}} = \frac{1}{14} \approx 0.0714 (or 7.14%7.14\%).

Loading workspace…