Resources

An engineering student tests the damping of a damped harmonic oscillator. The position amplitudes AnA_n are recorded at successive positive oscillation peaks numbered nn, but the data acquisition system records peak positions in non-standard units of mils (1 mil=0.001 in=2.54×10−5 m1\text{ mil} = 0.001\text{ in} = 2.54 \times 10^{-5}\text{ m}) and time intervals between successive peaks in milliseconds (ms\text{ms}):

Peak Number nnTime t (ms)t\text{ (ms)}Peak Amplitude An (mils)A_n\text{ (mils)}
000020002000
1145045012131213
22900900736736
3313501350446446
4418001800271271

Convert the peak amplitude at n=0n = 0 to standard SI units (meters). Then, construct a natural logarithmic decay plot ln⁡(An)\ln(A_n) versus elapsed time t (s)t\text{ (s)} to determine the damping constant γ\gamma in s−1\text{s}^{-1} defined by A(t)=A0e−γtA(t) = A_0 e^{-\gamma t}.

Answer and steps

Final answer

A0=5.08×10−2 mA_0 = 5.08 \times 10^{-2}\text{ m}; γ=1.11 s−1\gamma = 1.11\text{ s}^{-1}

Steps

01

Convert the initial peak amplitude to SI units

The initial peak amplitude corresponds to n=0n = 0: A0=2000 milsA_0 = 2000\text{ mils}

Using the given conversion factor 1 mil=2.54×10−5 m1\text{ mil} = 2.54 \times 10^{-5}\text{ m}: A0=2000×2.54×10−5 m=5.08×10−2 mA_0 = 2000 \times 2.54 \times 10^{-5}\text{ m} = 5.08 \times 10^{-2}\text{ m}


02

Linearize the exponential decay equation

The amplitude of a damped harmonic oscillator decays according to: A(t)=A0e−γtA(t) = A_0 e^{-\gamma t}

Taking the natural logarithm of both sides: ln⁡(A(t))=ln⁡(A0)−γt\ln(A(t)) = \ln(A_0) - \gamma t

This relationship matches the linear equation form y=mx+by = mx + b, where:

  • The dependent variable is y=ln⁡(An)y = \ln(A_n)
  • The independent variable is x=tx = t (in seconds)
  • The vertical intercept is b=ln⁡(A0)b = \ln(A_0)
  • The slope of the line is m=−γm = -\gamma

Pitfall Note: The units of amplitude in the logarithm do not affect the slope γ\gamma, because changing units only adds a constant ln⁡(c)\ln(c) shift to all ln⁡(An)\ln(A_n) values without altering differences Δln⁡(An)\Delta \ln(A_n). However, time must be converted from milliseconds (ms\text{ms}) to standard seconds (s\text{s}) so that γ\gamma is correctly expressed in s−1\text{s}^{-1}.


03

Compute values for the linear plot

Convert each time value to seconds (t (s)=t (ms)1000t\text{ (s)} = \frac{t\text{ (ms)}}{1000}) and calculate ln⁡(An)\ln(A_n):

nnt (s)t\text{ (s)}An (mils)A_n\text{ (mils)}ln⁡(An)\ln(A_n)
000.000.0020002000ln⁡(2000)≈7.601\ln(2000) \approx 7.601
110.450.4512131213ln⁡(1213)≈7.101\ln(1213) \approx 7.101
220.900.90736736ln⁡(736)≈6.601\ln(736) \approx 6.601
331.351.35446446ln⁡(446)≈6.100\ln(446) \approx 6.100
441.801.80271271ln⁡(271)≈5.602\ln(271) \approx 5.602

04

Determine the damping constant from the slope

Using the first and last data points to find the slope of the linear fit: m=Δln⁡(An)Δt=5.602−7.6011.80 s−0.00 s=−1.9991.80 s≈−1.11 s−1m = \frac{\Delta \ln(A_n)}{\Delta t} = \frac{5.602 - 7.601}{1.80\text{ s} - 0.00\text{ s}} = \frac{-1.999}{1.80\text{ s}} \approx -1.11\text{ s}^{-1}

Since the slope equals −γ-\gamma: −γ=−1.11 s−1  ⟹  γ=1.11 s−1-\gamma = -1.11\text{ s}^{-1} \implies \gamma = 1.11\text{ s}^{-1}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert the elapsed time from milliseconds to seconds, obtaining a damping constant that is off by a factor of 1000.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A0=2000×2.54×10−5 m=0.0508 mA_0 = 2000 \times 2.54 \times 10^{-5}\text{ m} = 0.0508\text{ m}

  2. Step 2

    ln⁡(A0)=ln⁡(2000)=7.601  ⟹  ln⁡(A4)=ln⁡(271)=5.602\ln(A_0) = \ln(2000) = 7.601 \implies \ln(A_4) = \ln(271) = 5.602

  3. Step 3

    slope=5.602−7.6011800−0=−1.9991800=−0.00111 ms−1\text{slope} = \frac{5.602 - 7.601}{1800 - 0} = \frac{-1.999}{1800} = -0.00111\text{ ms}^{-1}

    Correct

    slope=5.602−7.6011.80 s−0.00 s=−1.9991.80 s≈−1.11 s−1\text{slope} = \frac{5.602 - 7.601}{1.80\text{ s} - 0.00\text{ s}} = \frac{-1.999}{1.80\text{ s}} \approx -1.11\text{ s}^{-1}

    You calculated the slope using time in milliseconds (1800 ms1800\text{ ms}) instead of converting to seconds (1.80 s1.80\text{ s}) as specified by the prompt for elapsed time t (s)t\text{ (s)}.

  4. Step 4

    γ=−slope=0.00111 s−1\gamma = -\text{slope} = 0.00111\text{ s}^{-1}

    Correct

    γ=−slope=1.11 s−1\gamma = -\text{slope} = 1.11\text{ s}^{-1}

    Because your slope was evaluated in ms−1\text{ms}^{-1}, your final damping constant value was 0.001110.00111 rather than 1.11 s−11.11\text{ s}^{-1}. Additionally, note that 1 ms−1=1000 s−11\text{ ms}^{-1} = 1000\text{ s}^{-1}, so the unit label could not simply be changed without multiplying by 10001000.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly multiplied the initial amplitude by the conversion factor to obtain A0=0.0508 mA_0 = 0.0508\text{ m}.

You correctly used the natural logarithm to linearize the exponential decay equation A(t)=A0e−γtA(t) = A_0 e^{-\gamma t}.

You correctly identified the relationship γ=−slope\gamma = -\text{slope}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error

You forgot to convert elapsed time from milliseconds to seconds before computing the rise-over-run slope.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking the unit of the independent variable on the denominator of a derivative or slope calculation, or conflating rate units (since 1 ms−1=110−3 s=1000 s−11\text{ ms}^{-1} = \frac{1}{10^{-3}\text{ s}} = 1000\text{ s}^{-1}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Convert Table Quantities to Target SI Units First
  • Before computing slopes or rates, ensure all coordinates are expressed in target SI units (t in secondst\text{ in seconds}, so 1800 ms=1.80 s1800\text{ ms} = 1.80\text{ s}).

  • Always rewrite or re-tabulate the data column with target units before plugging values into ΔyΔx\frac{\Delta y}{\Delta x}.

Reciprocal Unit Conversion Rule
  • Units in the denominator invert their prefix multipliers: 1 ms−1=11 ms=110−3 s=1000 s−11\text{ ms}^{-1} = \frac{1}{1\text{ ms}} = \frac{1}{10^{-3}\text{ s}} = 1000\text{ s}^{-1}.

  • If a slope is obtained in inverse milliseconds, multiply by 10001000 to convert it to inverse seconds.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the total elapsed time to seconds: Δt=1800 ms=1.80 s\Delta t = 1800\text{ ms} = 1.80\text{ s}.

  2. Calculate the slope with SI units: slope=5.602−7.6011.80 s−0.00 s=−1.9991.80 s≈−1.11 s−1\text{slope} = \frac{5.602 - 7.601}{1.80\text{ s} - 0.00\text{ s}} = \frac{-1.999}{1.80\text{ s}} \approx -1.11\text{ s}^{-1}.

  3. Relate the slope to the damping constant: γ=−slope=−(−1.11 s−1)=1.11 s−1\gamma = -\text{slope} = -(-1.11\text{ s}^{-1}) = 1.11\text{ s}^{-1}.

Final answer

A0=5.08×10−2 mA_0 = 5.08 \times 10^{-2}\text{ m}; γ=1.11 s−1\gamma = 1.11\text{ s}^{-1}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how reciprocal units transform when converting prefixes in denominators.

  • Practice converting all raw experimental table values into standard SI units prior to graphical or slope analysis.

OverviewACEpath Teacher's Diagnosis

02 The student uses common logarithm (log₁₀) instead of the natural logarithm (ln) for the decay relation, yielding an incorrect slope.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A0=2000×2.54×10−5 m=0.0508 mA_0 = 2000 \times 2.54 \times 10^{-5}\text{ m} = 0.0508\text{ m}

  2. Step 2

    log⁡(A0)=3.301  ⟹  log⁡(A4)=log⁡(271)=2.433  ⟹  t4=1.80 s\log(A_0) = 3.301 \implies \log(A_4) = \log(271) = 2.433 \implies t_4 = 1.80\text{ s}

    Correct

    ln⁡(A0)=ln⁡(2000)≈7.601  ⟹  ln⁡(A4)=ln⁡(271)≈5.602  ⟹  t4=1.80 s\ln(A_0) = \ln(2000) \approx 7.601 \implies \ln(A_4) = \ln(271) \approx 5.602 \implies t_4 = 1.80\text{ s}

    You evaluated the base-1010 common logarithm log⁡10\log_{10} rather than the natural logarithm ln⁡\ln. Since the decay law is exponential with base ee (A(t)=A0e−γtA(t) = A_0 e^{-\gamma t}), you must take the natural logarithm to obtain a slope directly equal to −γ-\gamma.

  3. Step 3

    slope=2.433−3.3011.80=−0.8681.80=−0.482 s−1  ⟹  γ=0.482 s−1\text{slope} = \frac{2.433 - 3.301}{1.80} = \frac{-0.868}{1.80} = -0.482\text{ s}^{-1} \implies \gamma = 0.482\text{ s}^{-1}

    Correct

    slope=5.602−7.6011.80 s−0.00 s≈−1.11 s−1  ⟹  γ=1.11 s−1\text{slope} = \frac{5.602 - 7.601}{1.80\text{ s} - 0.00\text{ s}} \approx -1.11\text{ s}^{-1} \implies \gamma = 1.11\text{ s}^{-1}

    Because your slope was calculated from base-1010 logarithms, setting γ=−slope\gamma = -\text{slope} underestimated the damping constant by a factor of ln⁡(10)≈2.303\ln(10) \approx 2.303.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted the amplitude from mils to meters correctly using the given conversion factor.

You converted the time interval from milliseconds to seconds accurately.

You correctly recognized that the slope of the linearized plot relates directly to the damping rate.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Base-10 log vs. natural log confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You used the common logarithm (log⁡10\log_{10}) instead of the natural logarithm (ln⁡\ln). Because the natural exponential e−γte^{-\gamma t} is inverted by ln⁡\ln, taking ln⁡(A(t))=ln⁡(A0)−γt\ln(A(t)) = \ln(A_0) - \gamma t yields slope m=−γm = -\gamma. Using log⁡10\log_{10} instead yields log⁡10(A(t))=log⁡10(A0)−(γlog⁡10e)t\log_{10}(A(t)) = \log_{10}(A_0) - (\gamma \log_{10} e)t, making your slope m=−γ/ln⁡(10)m = -\gamma / \ln(10).

REASONING PATH
Your ACEpath teacher’s suggested approach
Logarithm Base Matching
  • For natural exponential relationships of the form y=y0ekty = y_0 e^{kt}, always apply ln⁡\ln so that ln⁡(ekt)=kt\ln(e^{kt}) = kt.

  • Check the base of the exponential term in the model: use ln⁡\ln for base ee and log⁡10\log_{10} only for base 1010.

Converting Between Bases
  • If base-1010 logarithms are plotted for a base-ee process, the slope is m=−γlog⁡10(e)=−γln⁡(10)m = -\gamma \log_{10}(e) = -\frac{\gamma}{\ln(10)}.

  • Multiply the base-10 slope magnitude by ln⁡(10)≈2.303\ln(10) \approx 2.303 to recover γ\gamma, or recalculate using ln⁡\ln directly.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Take the natural logarithm of the initial and final amplitudes: ln⁡(A0)=ln⁡(2000)≈7.601\ln(A_0) = \ln(2000) \approx 7.601 and ln⁡(A4)=ln⁡(271)≈5.602\ln(A_4) = \ln(271) \approx 5.602.

  2. Compute the slope of ln⁡(A)\ln(A) versus tt: slope=5.602−7.6011.80 s−0.00 s=−1.9991.80 s≈−1.11 s−1\text{slope} = \frac{5.602 - 7.601}{1.80\text{ s} - 0.00\text{ s}} = \frac{-1.999}{1.80\text{ s}} \approx -1.11\text{ s}^{-1}.

  3. Equate the slope to −γ-\gamma: −γ=−1.11 s−1  ⟹  γ=1.11 s−1-\gamma = -1.11\text{ s}^{-1} \implies \gamma = 1.11\text{ s}^{-1}.

Final answer

A0=5.08×10−2 mA_0 = 5.08 \times 10^{-2}\text{ m}; γ=1.11 s−1\gamma = 1.11\text{ s}^{-1}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check calculator keys to ensure you press 'ln' rather than 'log' when linearizing formulas containing Euler's number ee.

  • Practice deriving the linear form y=mx+by = mx + b explicitly by writing ln⁡(A(t))=ln⁡(A0)−γt\ln(A(t)) = \ln(A_0) - \gamma t before plugging in numerical values.

OverviewACEpath Teacher's Diagnosis

03 The student forgets the negative sign in the relationship between slope and damping constant, stating the damping constant as negative.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    A0=2000×2.54×10−5 m=0.0508 mA_0 = 2000 \times 2.54 \times 10^{-5}\text{ m} = 0.0508\text{ m}

  2. Step 2

    ln⁡(2000)=7.601  ⟹  ln⁡(271)=5.602  ⟹  t=1.80 s\ln(2000) = 7.601 \implies \ln(271) = 5.602 \implies t = 1.80\text{ s}

  3. Step 3

    slope=5.602−7.6011.80=−1.11 s−1\text{slope} = \frac{5.602 - 7.601}{1.80} = -1.11\text{ s}^{-1}

  4. Step 4

    γ=slope=−1.11 s−1\gamma = \text{slope} = -1.11\text{ s}^{-1}

    Correct

    −γ=slope=−1.11 s−1  ⟹  γ=1.11 s−1-\gamma = \text{slope} = -1.11\text{ s}^{-1} \implies \gamma = 1.11\text{ s}^{-1}

    Taking the logarithm of A(t)=A0e−γtA(t) = A_0 e^{-\gamma t} yields ln⁡(A(t))=ln⁡(A0)−γt\ln(A(t)) = \ln(A_0) - \gamma t. In this linear form y=b+mxy = b + mx, the slope is m=−γm = -\gamma, which means γ=−m=−(−1.11 s−1)=1.11 s−1\gamma = -m = -(-1.11\text{ s}^{-1}) = 1.11\text{ s}^{-1}.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted mils to meters accurately using the provided conversion factor.

You correctly transformed the time from milliseconds to seconds.

You computed the natural logarithms and the slope of the linear fit without arithmetic errors.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign error in linearized exponential parameter

You dropped the negative sign when relating the negative slope of the decay line to the positive decay constant γ\gamma.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the slope mm with the decay parameter γ\gamma in the equation y=b−γxy = b - \gamma x, where the slope is m=−γm = -\gamma rather than γ\gamma.

REASONING PATH
Your ACEpath teacher’s suggested approach
Match Linear Parameters Explicitly
  • Write y=mx+by = mx + b directly beneath your linearized equation: ln⁡(A)=−γt+ln⁡(A0)\ln(A) = -\gamma t + \ln(A_0).

  • Align mm with −γ-\gamma so you always solve for γ=−m\gamma = -m.

Physical Reality Check for Damping
  • A decaying amplitude requires a positive damping constant γ>0\gamma > 0 when written as e−γte^{-\gamma t}.

  • If your calculated γ\gamma is negative in an e−γte^{-\gamma t} decay model, verify your negative sign.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Linearize the decay formula: ln⁡(A(t))=ln⁡(A0)−γt\ln(A(t)) = \ln(A_0) - \gamma t.

  2. Identify the slope: m=−γ=−1.11 s−1m = -\gamma = -1.11\text{ s}^{-1}.

  3. Solve for the damping constant: γ=−(−1.11 s−1)=1.11 s−1\gamma = -(-1.11\text{ s}^{-1}) = 1.11\text{ s}^{-1}.

Final answer

A0=5.08×10−2 mA_0 = 5.08 \times 10^{-2}\text{ m}; γ=1.11 s−1\gamma = 1.11\text{ s}^{-1}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice matching linearized exponential decay equations directly to y=mx+by = mx + b to avoid sign slips on decay constants.

  • Perform a quick sign sanity check: exponential decay defined with a minus sign in the exponent (e−γte^{-\gamma t}) always yields a positive rate constant γ>0\gamma > 0.

Lock it in

Similar question

01

A capacitor discharges through a resistor such that voltage follows V(t)=V0e−t/τV(t) = V_0 e^{-t/\tau}. A plot of ln⁡(V)\ln(V) versus t (ms)t\text{ (ms)} yields a slope of −0.025 ms−1-0.025\text{ ms}^{-1}. Determine the time constant τ\tau in seconds.

Answer

τ=0.040 s\tau = 0.040\text{ s}. The decay constant is 1τ=−slope=0.025 ms−1=25 s−1\frac{1}{\tau} = -\text{slope} = 0.025\text{ ms}^{-1} = 25\text{ s}^{-1}. Thus, τ=125 s−1=0.040 s\tau = \frac{1}{25\text{ s}^{-1}} = 0.040\text{ s}.

02

A damped oscillator has peak amplitudes A1=800 mmA_1 = 800\text{ mm} at t1=200 mst_1 = 200\text{ ms} and A2=200 mmA_2 = 200\text{ mm} at t2=800 mst_2 = 800\text{ ms}. Calculate the damping coefficient γ\gamma in s−1\text{s}^{-1} defined by A(t)=A0e−γtA(t) = A_0 e^{-\gamma t}.

Answer

γ≈2.31 s−1\gamma \approx 2.31\text{ s}^{-1}. Convert time to seconds: Δt=0.800 s−0.200 s=0.600 s\Delta t = 0.800\text{ s} - 0.200\text{ s} = 0.600\text{ s}. The ratio is A1A2=800200=4=eγΔt\frac{A_1}{A_2} = \frac{800}{200} = 4 = e^{\gamma \Delta t}. Taking natural logs: γ=ln⁡(4)0.600 s=1.38630.600 s≈2.31 s−1\gamma = \frac{\ln(4)}{0.600\text{ s}} = \frac{1.3863}{0.600\text{ s}} \approx 2.31\text{ s}^{-1}.

03

An underdamped pendulum's amplitude is recorded as A=12.0∘A = 12.0^\circ at t=0t = 0 and A=1.50∘A = 1.50^\circ after 1515 complete cycles. If the period of oscillation is T=400 msT = 400\text{ ms}, find the damping constant γ\gamma in s−1\text{s}^{-1} and the logarithmic decrement δ\delta.

Answer

γ≈0.347 s−1\gamma \approx 0.347\text{ s}^{-1}; δ≈0.139\delta \approx 0.139. Total time Δt=15×0.400 s=6.00 s\Delta t = 15 \times 0.400\text{ s} = 6.00\text{ s}. Then ln⁡(12.0/1.50)=ln⁡(8)≈2.0794\ln(12.0 / 1.50) = \ln(8) \approx 2.0794. Damping constant γ=2.07946.00 s≈0.347 s−1\gamma = \frac{2.0794}{6.00\text{ s}} \approx 0.347\text{ s}^{-1}. Logarithmic decrement δ=γT=(0.3466 s−1)(0.400 s)≈0.139\delta = \gamma T = (0.3466\text{ s}^{-1})(0.400\text{ s}) \approx 0.139.

Loading workspace…