Resources

An exploration rover of mass m=50.0 kgm = 50.0\text{ kg} is winched up an adjustable icy incline. The coefficient of static friction is small, μs=0.0800\mu_s = 0.0800, and the winch cable pulls strictly parallel to the incline with tension TT. Take g=9.80 m/s2g = 9.80\text{ m/s}^2. (a) Write the expressions for the normal force FN(θ)F_N(\theta) and the minimum tension Tmin⁡(θ)T_{\min}(\theta) required to prevent the rover from sliding backward down the incline as explicit functions of the incline angle θ\theta. (b) Evaluate the asymptotic limits of FNF_N and Tmin⁡T_{\min} as the slope becomes flat (θ→0∘\theta \to 0^\circ) and as the slope becomes vertical (θ→90∘\theta \to 90^\circ), and provide the physical interpretation of each limit.

Answer and steps

Final answer

(a) FN(θ)=mgcos⁡θ=490cos⁡θ NF_N(\theta) = mg\cos\theta = 490\cos\theta\text{ N}, Tmin⁡(θ)=mg(sin⁡θ−μscos⁡θ)=490(sin⁡θ−0.0800cos⁡θ) NT_{\min}(\theta) = mg(\sin\theta - \mu_s\cos\theta) = 490(\sin\theta - 0.0800\cos\theta)\text{ N} (for tan⁡θ≥μs\tan\theta \ge \mu_s); (b) As θ→0∘\theta \to 0^\circ: FN→mg=490 NF_N \to mg = 490\text{ N} and Tmin⁡→0 NT_{\min} \to 0\text{ N} (friction alone supports the static state on flat ground); as θ→90∘\theta \to 90^\circ: FN→0 NF_N \to 0\text{ N} and Tmin⁡→mg=490 NT_{\min} \to mg = 490\text{ N} (contact with the wall vanishes, static friction drops to zero, and tension must support the entire vertical weight).

Steps

Part (a): Free-Body Diagram and Equilibrium Equations

  1. Establish the Coordinate System: Align the coordinate axes with the inclined plane:

    • Let the +x+x-axis point up along the surface of the incline.
    • Let the +y+y-axis point perpendicularly upward away from the surface.
  2. Identify and Resolve All Forces:

    • Gravitational force (mgmg): Acts vertically downward. Resolving into components gives: Wx=−mgsin⁡θ,Wy=−mgcos⁡θW_x = -mg\sin\theta, \quad W_y = -mg\cos\theta
    • Normal force (FNF_N): Acts perpendicular to the surface in the +y+y-direction: FN,y=FNF_{N,y} = F_N
    • Cable tension (TT): Acts parallel to the incline in the +x+x-direction: Tx=TT_x = T
    • Static friction (fsf_s): Since we want the minimum tension Tmin⁡T_{\min} to prevent the rover from sliding backward (downward), the rover is on the verge of slipping down. Therefore, static friction acts upward along the plane (+x+x-direction) at its maximum value: fs,max⁡=μsFNf_{s,\max} = \mu_s F_N
  3. Equilibrium in the Perpendicular Direction (yy-axis): Because there is no acceleration perpendicular to the incline: ∑Fy=FN−mgcos⁡θ=0\sum F_y = F_N - mg\cos\theta = 0 FN(θ)=mgcos⁡θF_N(\theta) = mg\cos\theta Substituting m=50.0 kgm = 50.0\text{ kg} and g=9.80 m/s2g = 9.80\text{ m/s}^2 (mg=490 Nmg = 490\text{ N}): FN(θ)=490cos⁡θ NF_N(\theta) = 490\cos\theta\text{ N}
  4. Equilibrium in the Parallel Direction (xx-axis): Setting the net force along the incline to zero: ∑Fx=Tmin⁡+fs,max⁡−mgsin⁡θ=0\sum F_x = T_{\min} + f_{s,\max} - mg\sin\theta = 0 Tmin⁡+μsFN−mgsin⁡θ=0T_{\min} + \mu_s F_N - mg\sin\theta = 0 Substitute FN=mgcos⁡θF_N = mg\cos\theta: Tmin⁡(θ)=mg(sin⁡θ−μscos⁡θ)T_{\min}(\theta) = mg(\sin\theta - \mu_s\cos\theta) Using the numerical values: Tmin⁡(θ)=490(sin⁡θ−0.0800cos⁡θ) NT_{\min}(\theta) = 490(\sin\theta - 0.0800\cos\theta)\text{ N} (Note: This expression applies when the downslope component of gravity exceeds maximum static friction, i.e., tan⁡θ≥μs\tan\theta \ge \mu_s. For smaller angles, the rover stays at rest even with T=0 NT = 0\text{ N}.)

Part (b): Asymptotic Limits and Physical Interpretations

  1. Limit as the Slope Becomes Flat (θ→0∘\theta \to 0^\circ):

    • cos⁡(0∘)=1  ⟹  FN→mg=490 N\cos(0^\circ) = 1 \implies F_N \to mg = 490\text{ N}
    • For θ→0∘\theta \to 0^\circ, gravity has no downslope component (sin⁡0∘=0\sin 0^\circ = 0). Since the slope is flat, static friction alone readily prevents any motion, so no tension is required: Tmin⁡→0 NT_{\min} \to 0\text{ N}
    • Physical Interpretation: On level ground, the normal force completely balances the rover's weight (FN=mgF_N = mg). With no component of gravity pulling along the surface, the cable does not need to exert any tension to prevent backward sliding.
  2. Limit as the Slope Becomes Vertical (θ→90∘\theta \to 90^\circ):

    • cos⁡(90∘)=0  ⟹  FN→0 N\cos(90^\circ) = 0 \implies F_N \to 0\text{ N}
    • sin⁡(90∘)=1  ⟹  Tmin⁡→mg(sin⁡90∘−μscos⁡90∘)=mg=490 N\sin(90^\circ) = 1 \implies T_{\min} \to mg(\sin 90^\circ - \mu_s\cos 90^\circ) = mg = 490\text{ N}
    • Physical Interpretation: When the incline is vertical, the rover no longer presses against the surface, so the normal force vanishes (FN=0F_N = 0). Without a normal force, static friction drops to zero (fs=μsFN=0f_s = \mu_s F_N = 0). Consequently, the winch cable must support the entire vertical weight of the rover (Tmin⁡=mgT_{\min} = mg).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student reverses the direction of static friction, assuming friction opposes tension rather than the downward impending motion.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    FN=m⋅g⋅cos⁡(θ)=490cos⁡(θ) NF_N = m \cdot g \cdot \cos(\theta) = 490\cos(\theta)\text{ N}

  2. Step 2

    Tmin⁡−m⋅g⋅sin⁡(θ)−fs=0  ⟹  Tmin⁡(θ)=490sin⁡(θ)+39.2cos⁡(θ) NT_{\min} - m \cdot g \cdot \sin(\theta) - f_s = 0 \implies T_{\min}(\theta) = 490\sin(\theta) + 39.2\cos(\theta)\text{ N}

    Correct

    ∑Fx=Tmin⁡+fs,max⁡−mgsin⁡θ=0  ⟹  Tmin⁡(θ)=490(sin⁡θ−0.0800cos⁡θ) N\sum F_x = T_{\min} + f_{s,\max} - mg\sin\theta = 0 \implies T_{\min}(\theta) = 490(\sin\theta - 0.0800\cos\theta)\text{ N}

    To prevent the rover from sliding backward down the slope, impending motion is directed downslope. Static friction opposes impending motion and therefore acts upslope (+x+x), helping the cable rather than opposing it.

  3. Step 3

    At θ→0∘:FN→490 N,  Tmin⁡→39.2 N  ⟹  cable must overcome friction even on flat ground.\text{At } \theta \to 0^\circ: F_N \to 490\text{ N},\; T_{\min} \to 39.2\text{ N} \implies \text{cable must overcome friction even on flat ground.}; At θ→90∘:FN→0 N,  Tmin⁡→490 N  ⟹  normal force vanishes and tension holds full weight.\text{At } \theta \to 90^\circ: F_N \to 0\text{ N},\; T_{\min} \to 490\text{ N} \implies \text{normal force vanishes and tension holds full weight.}

    Correct

    θ→0∘:FN→490 N,  Tmin⁡→0 N\theta \to 0^\circ: F_N \to 490\text{ N},\; T_{\min} \to 0\text{ N} (friction alone maintains equilibrium without cable pull); θ→90∘:FN→0 N,  Tmin⁡→490 N\theta \to 90^\circ: F_N \to 0\text{ N},\; T_{\min} \to 490\text{ N} (contact disappears, friction vanishes, and tension supports full weight)

    Your analysis for θ→90∘\theta \to 90^\circ is physically sound, but for θ→0∘\theta \to 0^\circ, your reversed friction sign led to a non-zero minimum tension (39.2 N39.2\text{ N}). On a flat surface, the rover has no tendency to slide on its own, so zero tension is required.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly resolved the normal force perpendicular to the inclined plane as FN=mgcos⁡θF_N = mg\cos\theta.

You correctly recognized that maximum static friction is given by fs,max⁡=μsFNf_{s,\max} = \mu_s F_N.

You correctly evaluated and physically interpreted the vertical slope limit at θ→90∘\theta \to 90^\circ.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Reversed Static Friction Direction

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that friction always opposes the pulling force (tension) instead of opposing the direction of impending relative motion (sliding backward down the incline).

REASONING PATH
Your ACEpath teacher’s suggested approach
Direction of Static Friction
  • Static friction always opposes the direction of impending relative motion, not necessarily applied external forces.

  • Ask yourself: 'If the cable tension were slightly too small, which way would the rover slip?' Since it slips downslope, static friction must point upslope.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up equilibrium along the incline with impending downslope slip: ∑Fx=Tmin⁡+fs,max⁡−mgsin⁡θ=0\sum F_x = T_{\min} + f_{s,\max} - mg\sin\theta = 0.

  2. Substitute fs,max⁡=μsFN=μsmgcos⁡θf_{s,\max} = \mu_s F_N = \mu_s mg\cos\theta: Tmin⁡=mg(sin⁡θ−μscos⁡θ)T_{\min} = mg(\sin\theta - \mu_s\cos\theta).

  3. Insert the values m=50.0 kgm = 50.0\text{ kg}, g=9.80 m/s2g = 9.80\text{ m/s}^2, and μs=0.0800\mu_s = 0.0800: Tmin⁡(θ)=490(sin⁡θ−0.0800cos⁡θ) NT_{\min}(\theta) = 490(\sin\theta - 0.0800\cos\theta)\text{ N} for tan⁡θ≥μs\tan\theta \ge \mu_s.

  4. Re-evaluate θ→0∘\theta \to 0^\circ: with no downslope gravity component, the rover rests naturally, giving Tmin⁡→0 NT_{\min} \to 0\text{ N}.

Final answer

(a) FN(θ)=490cos⁡θ NF_N(\theta) = 490\cos\theta\text{ N}, Tmin⁡(θ)=490(sin⁡θ−0.0800cos⁡θ) NT_{\min}(\theta) = 490(\sin\theta - 0.0800\cos\theta)\text{ N}; (b) As θ→0∘\theta \to 0^\circ, FN→490 NF_N \to 490\text{ N} and Tmin⁡→0 NT_{\min} \to 0\text{ N}; as θ→90∘\theta \to 90^\circ, FN→0 NF_N \to 0\text{ N} and Tmin⁡→490 NT_{\min} \to 490\text{ N}.

NEXT STEPS
Final Takeaways from Your Teacher
  • Draw an arrow indicating the direction of impending slip before placing the friction vector on your free-body diagram.

  • Check boundary cases: on a flat surface (θ=0∘\theta = 0^\circ), an object at rest requires zero tension to stay at rest.

OverviewACEpath Teacher's Diagnosis

02 The student confuses the trigonometric components of gravity, using sine for the normal force and cosine for the parallel component.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    FN=m∗g∗sin⁡(θ)=490sin⁡(θ) NF_N = m*g*\sin(\theta) = 490\sin(\theta)\text{ N}

    Correct

    FN(θ)=mgcos⁡θ=490cos⁡θ NF_N(\theta) = mg\cos\theta = 490\cos\theta\text{ N}

    You used sin⁡θ\sin\theta instead of cos⁡θ\cos\theta for the perpendicular component of gravity. When an incline has angle θ\theta relative to the horizontal, the angle between the downward vertical and the normal axis is also θ\theta, making the adjacent component mgcos⁡θmg\cos\theta.

  2. Step 2

    Tmin⁡+μs∗FN−m∗g∗cos⁡(θ)=0  ⟹  Tmin⁡(θ)=490cos⁡(θ)−39.2sin⁡(θ) NT_{\min} + \mu_s * F_N - m*g*\cos(\theta) = 0 \implies T_{\min}(\theta) = 490\cos(\theta) - 39.2\sin(\theta)\text{ N}

    Correct

    Tmin⁡+μsFN−mgsin⁡θ=0  ⟹  Tmin⁡(θ)=490(sin⁡θ−0.0800cos⁡θ) NT_{\min} + \mu_s F_N - mg\sin\theta = 0 \implies T_{\min}(\theta) = 490(\sin\theta - 0.0800\cos\theta)\text{ N}

    You correctly recognized that static friction acts up the incline to prevent sliding down, but you used mgcos⁡θmg\cos\theta for the parallel component of gravity instead of the opposite component mgsin⁡θmg\sin\theta.

  3. Step 3

    At θ→0∘:FN→0 N,Tmin⁡→490 N\text{At }\theta \to 0^\circ: F_N \to 0\text{ N}, T_{\min} \to 490\text{ N}; the normal force is zero and full tension is needed horizontally.

    Correct

    At θ→0∘:FN→490 N,Tmin⁡→0 N\text{At }\theta \to 0^\circ: F_N \to 490\text{ N}, T_{\min} \to 0\text{ N}; on level ground, normal force supports the full weight and static friction keeps the rover at rest without cable tension.

    Your limit calculation followed your expressions from Step 1 and Step 2 correctly, but the result contradicts the physical situation on flat ground, where the surface supports the entire weight (FN=mgF_N = mg).

  4. Step 4

    At θ→90∘:FN→490 N,Tmin⁡→−39.2 N\text{At }\theta \to 90^\circ: F_N \to 490\text{ N}, T_{\min} \to -39.2\text{ N}; normal force equals full weight and tension becomes negative.

    Correct

    At θ→90∘:FN→0 N,Tmin⁡→490 N\text{At }\theta \to 90^\circ: F_N \to 0\text{ N}, T_{\min} \to 490\text{ N}; against a vertical wall, contact force drops to zero and the cable must support the full vertical weight.

    This step evaluated your swapped equations correctly, but on a vertical cliff the rover loses contact with the surface, so FN→0 NF_N \to 0\text{ N} and the cable tension must carry the full gravitational load (Tmin⁡→mgT_{\min} \to mg).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly determined that maximum static friction points up the incline to resist downward sliding.

You correctly formulated the parallel equilibrium condition relating tension, friction, and the gravitational pull.

You systematically evaluated the boundary limits of your algebraic expressions.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric Component Inversion on Incline

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You associated the incline angle θ\theta with the opposite side when resolving gravity perpendicular to the surface, reversing the roles of sin⁡θ\sin\theta and cos⁡θ\cos\theta for the coordinate axes aligned with the slope.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identifying the Reference Angle in Incline FBDs
  • When the incline is elevated at angle θ\theta from the horizontal, the angle between the downward weight vector W⃗\vec{W} and the perpendicular axis into the incline is always θ\theta.

  • Draw the right triangle formed by W⃗\vec{W} and the axes: the side adjacent to θ\theta is W⊥=mgcos⁡θW_\perp = mg\cos\theta, and the side opposite to θ\theta is W∥=mgsin⁡θW_\parallel = mg\sin\theta.

Sanity Check via Extreme Angles (0° and 90°)
  • On a flat surface (θ=0∘\theta = 0^\circ), normal force must equal full weight (mgmg) and downslope gravity must vanish (00).

  • Before solving further, test θ=0∘\theta = 0^\circ: if your perpendicular force has sin⁡(0∘)=0\sin(0^\circ) = 0, you have inverted sine and cosine.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Decompose the gravitational force into components aligned with the incline: W⊥=mgcos⁡θW_\perp = mg\cos\theta and W∥=mgsin⁡θW_\parallel = mg\sin\theta.

  2. Set the perpendicular net force to zero: FN−mgcos⁡θ=0  ⟹  FN(θ)=(50.0)(9.80)cos⁡θ=490cos⁡θ NF_N - mg\cos\theta = 0 \implies F_N(\theta) = (50.0)(9.80)\cos\theta = 490\cos\theta\text{ N}.

  3. Set the parallel net force to zero for impending downward slip: Tmin⁡+μsFN−mgsin⁡θ=0T_{\min} + \mu_s F_N - mg\sin\theta = 0.

  4. Substitute FNF_N: Tmin⁡(heta)=mg(sin⁡θ−μscos⁡θ)=490(sin⁡θ−0.0800cos⁡θ) NT_{\min}( heta) = mg(\sin\theta - \mu_s\cos\theta) = 490(\sin\theta - 0.0800\cos\theta)\text{ N} (for tan⁡θ≥0.0800\tan\theta \ge 0.0800).

  5. Evaluate limits: as θ→0∘\theta \to 0^\circ, FN→490 NF_N \to 490\text{ N} and Tmin⁡→0 NT_{\min} \to 0\text{ N}; as θ→90∘\theta \to 90^\circ, FN→0 NF_N \to 0\text{ N} and Tmin⁡→490 NT_{\min} \to 490\text{ N}.

Final answer

(a) FN(θ)=490cos⁡θ NF_N(\theta) = 490\cos\theta\text{ N}, Tmin⁡(heta)=490(sin⁡θ−0.0800cos⁡θ) NT_{\min}( heta) = 490(\sin\theta - 0.0800\cos\theta)\text{ N}; (b) As θ→0∘\theta \to 0^\circ: FN→490 NF_N \to 490\text{ N}, Tmin⁡→0 NT_{\min} \to 0\text{ N}; as θ→90∘\theta \to 90^\circ: FN→0 NF_N \to 0\text{ N}, Tmin⁡→490 NT_{\min} \to 490\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice sketching the geometry triangle between the vertical weight vector and the normal axis on inclined planes.

  • Always run an extreme-case check (θ=0∘\theta = 0^\circ) immediately after writing component equations to verify that FN=mgF_N = mg.

OverviewACEpath Teacher's Diagnosis

03 The student assumes the normal force is always equal to the full weight m*g regardless of the incline angle.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    FN=m⋅g=490 NF_N = m \cdot g = 490\text{ N}

    Correct

    FN(θ)=mgcos⁡θ=490cos⁡θ NF_N(\theta) = mg\cos\theta = 490\cos\theta\text{ N}

    On an incline angled at θ\theta, gravity must be resolved into perpendicular and parallel components. The normal force balances the perpendicular component of gravity, giving FN(θ)=mgcos⁡θF_N(\theta) = mg\cos\theta, which depends on the incline angle.

  2. Step 2

    Tmin⁡+μs⋅FN−m⋅g⋅sin⁡(θ)=0  ⟹  Tmin⁡(θ)=490sin⁡(θ)−0.0800(490)=490sin⁡(θ)−39.2 NT_{\min} + \mu_s \cdot F_N - m \cdot g \cdot \sin(\theta) = 0 \implies T_{\min}(\theta) = 490\sin(\theta) - 0.0800(490) = 490\sin(\theta) - 39.2\text{ N}

    Correct

    Tmin⁡(θ)=mg(sin⁡θ−μscos⁡θ)=490(sin⁡θ−0.0800cos⁡θ) NT_{\min}(\theta) = mg(\sin\theta - \mu_s\cos\theta) = 490(\sin\theta - 0.0800\cos\theta)\text{ N}

    Your equilibrium equation along the incline is set up properly, but substituting FN=490 NF_N = 490\text{ N} instead of 490cos⁡θ N490\cos\theta\text{ N} carried the error into your tension formula.

  3. Step 3

    At θ→0∘\theta \to 0^\circ: FN→490 NF_N \to 490\text{ N}, Tmin⁡→−39.2 NT_{\min} \to -39.2\text{ N}; normal force equals total weight and friction prevents movement without tension. \nAt θ→90∘\theta \to 90^\circ: FN→490 NF_N \to 490\text{ N}, Tmin⁡→450.8 NT_{\min} \to 450.8\text{ N}; surface still exerts full normal force so friction reduces the tension needed to hold the weight.

    Correct

    At θ→0∘\theta \to 0^\circ: FN→490 NF_N \to 490\text{ N}, Tmin⁡→0 NT_{\min} \to 0\text{ N} (friction balances down-slope forces on level ground). \nAt θ→90∘\theta \to 90^\circ: FN→0 NF_N \to 0\text{ N}, Tmin⁡→490 NT_{\min} \to 490\text{ N} (contact vanishes, static friction drops to zero, and the cable supports the full weight).

    Because FNF_N varies as cos⁡θ\cos\theta, at θ→90∘\theta \to 90^\circ the surface exerts zero normal force (FN→0F_N \to 0), which means static friction vanishes and the cable must support the rover's full weight (Tmin⁡=490 NT_{\min} = 490\text{ N}).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly resolved the component of gravity acting parallel to the incline as mgsin⁡θmg\sin\theta.

You oriented maximum static friction up the incline to prevent the rover from sliding backward.

You correctly calculated the numerical magnitude of the rover's weight as mg=490 Nmg = 490\text{ N}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Normal force treated as constant $mg$ on an incline

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the normal force as a fixed quantity equal to mgmg rather than setting up Newton's second law along the perpendicular axis (yy-axis) to find FN=mgcos⁡θF_N = mg\cos\theta.

REASONING PATH
Your ACEpath teacher’s suggested approach
Establish Perpendicular Equilibrium
  • For a surface tilted at angle θ\theta with no perpendicular acceleration, the normal force balances the perpendicular component of gravity: ∑F⊥=FN−mgcos⁡θ=0\sum F_\perp = F_N - mg\cos\theta = 0.

  • Always draw a tilted coordinate frame and resolve the weight vector into mgcos⁡θmg\cos\theta (perpendicular to surface) and mgsin⁡θmg\sin\theta (parallel to surface).

Check Physical Limits
  • As a slope approaches a vertical wall (θ→90∘\theta \to 90^\circ), an object resting without a horizontal pressing force loses contact pressure: FN→0F_N \to 0.

  • Verify whether your normal force formula properly vanishes at 90∘90^\circ and equals mgmg at 0∘0^\circ.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Resolve forces perpendicular to the incline: ∑Fy=FN−mgcos⁡θ=0  ⟹  FN(θ)=mgcos⁡θ=490cos⁡θ N\sum F_y = F_N - mg\cos\theta = 0 \implies F_N(\theta) = mg\cos\theta = 490\cos\theta\text{ N}.

  2. Substitute FN(θ)F_N(\theta) into the parallel equilibrium equation: Tmin⁡+μsFN−mgsin⁡θ=0  ⟹  Tmin⁡(θ)=mg(sin⁡θ−μscos⁡θ)=490(sin⁡θ−0.0800cos⁡θ) NT_{\min} + \mu_s F_N - mg\sin\theta = 0 \implies T_{\min}(\theta) = mg(\sin\theta - \mu_s\cos\theta) = 490(\sin\theta - 0.0800\cos\theta)\text{ N}.

  3. Evaluate θ→0∘\theta \to 0^\circ: cos⁡(0∘)=1  ⟹  FN→490 N\cos(0^\circ) = 1 \implies F_N \to 490\text{ N}; since gravity has no downslope component, tension is zero (Tmin⁡→0 NT_{\min} \to 0\text{ N}).

  4. Evaluate θ→90∘\theta \to 90^\circ: cos⁡(90∘)=0  ⟹  FN→0 N\cos(90^\circ) = 0 \implies F_N \to 0\text{ N} and sin⁡(90∘)=1  ⟹  Tmin⁡→490 N\sin(90^\circ) = 1 \implies T_{\min} \to 490\text{ N}, meaning the winch alone holds the entire vertical weight.

Final answer

(a) FN(θ)=490cos⁡θ NF_N(\theta) = 490\cos\theta\text{ N}, Tmin⁡(θ)=490(sin⁡θ−0.0800cos⁡θ) NT_{\min}(\theta) = 490(\sin\theta - 0.0800\cos\theta)\text{ N} (for tan⁡θ≥0.0800\tan\theta \ge 0.0800); (b) As θ→0∘\theta \to 0^\circ: FN→490 NF_N \to 490\text{ N}, Tmin⁡→0 NT_{\min} \to 0\text{ N}; as θ→90∘\theta \to 90^\circ: FN→0 NF_N \to 0\text{ N}, Tmin⁡→490 NT_{\min} \to 490\text{ N}.

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice drawing free-body diagrams on inclined planes with tilted xx-yy axes.

  • Check that FNF_N always scales with cos⁡θ\cos\theta when no other perpendicular forces act on the object.

  • Test limiting cases (θ=0∘\theta = 0^\circ and θ=90∘\theta = 90^\circ) before finalizing algebraic formulas.

Lock it in

Similar question

01

A 20.0 kg20.0\text{ kg} crate sits on a 30.0∘30.0^\circ incline with μs=0.250\mu_s = 0.250. A cable pulls upward along the slope. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, find the minimum cable tension Tmin⁡T_{\min} needed to keep the crate from sliding down the incline.

Answer

Tmin⁡=mg(sin⁡30.0∘−μscos⁡30.0∘)=(20.0)(9.80)(0.500−0.250×0.8660)≈55.6 NT_{\min} = mg(\sin 30.0^\circ - \mu_s\cos 30.0^\circ) = (20.0)(9.80)(0.500 - 0.250\times 0.8660) \approx 55.6\text{ N}.

02

A box of mass mm rests on an incline of angle θ\theta where tan⁡θ>μs\tan\theta > \mu_s. A force PP pushes parallel to the incline. Determine the range of forces [Pmin⁡,Pmax⁡][P_{\min}, P_{\max}] for which the box remains stationary on the incline.

Answer

For impending downward slip: Pmin⁡=mg(sin⁡θ−μscos⁡θ)P_{\min} = mg(\sin\theta - \mu_s\cos\theta). For impending upward slip: Pmax⁡=mg(sin⁡θ+μscos⁡θ)P_{\max} = mg(\sin\theta + \mu_s\cos\theta). Range: mg(sin⁡θ−μscos⁡θ)≤P≤mg(sin⁡θ+μscos⁡θ)mg(\sin\theta - \mu_s\cos\theta) \le P \le mg(\sin\theta + \mu_s\cos\theta).

03

A block of mass m=10.0 kgm = 10.0\text{ kg} is held against a vertical wall by a horizontal pushing force FF. The coefficient of static friction between the block and the wall is μs=0.400\mu_s = 0.400. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate the minimum horizontal force Fmin⁡F_{\min} needed to prevent the block from slipping downward.

Answer

Impending motion is downward, so static friction acts upward: fs=mgf_s = mg. At minimum push, fs,max⁡=μsFN=μsF=mgf_{s,\max} = \mu_s F_N = \mu_s F = mg. Thus Fmin⁡=mgμs=(10.0)(9.80)0.400=245 NF_{\min} = \frac{mg}{\mu_s} = \frac{(10.0)(9.80)}{0.400} = 245\text{ N}.

Loading workspace…