Resources

A cyclic heat engine operates between a high-temperature thermal reservoir at TH=580 KT_H = 580\text{ K} and a low-temperature exhaust reservoir at TC=290 KT_C = 290\text{ K}. In each complete cycle, the engine absorbs QH=2.40×103 JQ_H = 2.40 \times 10^3\text{ J} of heat from the hot reservoir and performs Wout=720 JW_{\text{out}} = 720\text{ J} of net mechanical work on its surroundings. Calculate: (a) the thermal efficiency η\eta of this engine, (b) the theoretical maximum Carnot efficiency ηCarnot\eta_{\text{Carnot}} possible between these two reservoirs, and (c) the quantity of waste heat ∣QC∣|Q_C| discharged to the cold reservoir per cycle.

Answer and steps

Final answer

(a) η=0.300\eta = 0.300 (or 30.0%30.0\%); (b) ηCarnot=0.500\eta_{\text{Carnot}} = 0.500 (or 50.0%50.0\%); (c) ∣QC∣=1.68×103 J|Q_C| = 1.68 \times 10^3\text{ J}.

Steps

(a) Calculating the Thermal Efficiency η\eta

The thermal efficiency η\eta of any heat engine is defined as the ratio of the net work output WoutW_{\text{out}} delivered by the engine to the total heat energy absorbed from the hot reservoir QHQ_H during one complete cycle:

η=WoutQH\eta = \frac{W_{\text{out}}}{Q_H}

Substitute the given values into the formula:

η=720 J2.40×103 J=0.300=30.0%\eta = \frac{720\text{ J}}{2.40 \times 10^3\text{ J}} = 0.300 = 30.0\%


(b) Calculating the Carnot Maximum Efficiency ηCarnot\eta_{\text{Carnot}}

The Carnot efficiency represents the theoretical upper limit on the efficiency of any heat engine operating between two absolute temperatures, THT_H and TCT_C:

ηCarnot=1−TCTH\eta_{\text{Carnot}} = 1 - \frac{T_C}{T_H}

Pitfall: Always ensure temperatures are expressed on an absolute scale (Kelvin). Here, both temperatures are already given in Kelvin:

ηCarnot=1−290 K580 K=1−0.500=0.500=50.0%\eta_{\text{Carnot}} = 1 - \frac{290\text{ K}}{580\text{ K}} = 1 - 0.500 = 0.500 = 50.0\%

Notice that the actual efficiency η=30.0%\eta = 30.0\% is less than the theoretical limit ηCarnot=50.0%\eta_{\text{Carnot}} = 50.0\%, which is consistent with the Second Law of Thermodynamics for real, irreversible engines.


(c) Calculating the Waste Heat Discharged ∣QC∣|Q_C|

Because the engine undergoes a cyclic process, its internal energy returns to its initial state at the end of each cycle (ΔU=0\Delta U = 0). By the First Law of Thermodynamics, energy conservation gives:

Qnet=Wout  ⟹  QH−∣QC∣=WoutQ_{\text{net}} = W_{\text{out}} \implies Q_H - |Q_C| = W_{\text{out}}

Rearrange to solve for the waste heat ∣QC∣|Q_C| expelled to the cold reservoir:

∣QC∣=QH−Wout|Q_C| = Q_H - W_{\text{out}}

Substitute the known quantities:

∣QC∣=2400 J−720 J=1680 J=1.68×103 J|Q_C| = 2400\text{ J} - 720\text{ J} = 1680\text{ J} = 1.68 \times 10^3\text{ J}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the definition of thermal efficiency by dividing work by waste heat instead of heat absorbed from the hot reservoir.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    η=WoutQC  ⟹  η=7201680≈0.43\eta = \frac{W_{\text{out}}}{Q_C} \implies \eta = \frac{720}{1680} \approx 0.43

    Correct

    η=WoutQH=720 J2400 J=0.300 (or 30.0%)\eta = \frac{W_{\text{out}}}{Q_H} = \frac{720\text{ J}}{2400\text{ J}} = 0.300\text{ (or } 30.0\%\text{)}

    Thermal efficiency is defined as what you get out divided by what you pay for: η=WoutQH\eta = \frac{W_{\text{out}}}{Q_H}. You placed the waste heat ∣QC∣|Q_C| in the denominator instead of the input heat QHQ_H absorbed from the hot reservoir.

  2. Step 2

    ηCarnot=1−TCTH  ⟹  ηCarnot=1−290580=0.50\eta_{\text{Carnot}} = 1 - \frac{T_C}{T_H} \implies \eta_{\text{Carnot}} = 1 - \frac{290}{580} = 0.50

  3. Step 3

    ∣QC∣=QH−Wout  ⟹  ∣QC∣=2400−720=1680 J|Q_C| = Q_H - W_{\text{out}} \implies |Q_C| = 2400 - 720 = 1680\text{ J}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly stated and evaluated the Carnot efficiency formula using absolute temperatures.

You applied the first law of thermodynamics to find the waste heat discharged to the cold reservoir.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Definition Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the input heat energy QHQ_H with the exhausted waste heat QCQ_C in the denominator of the thermal efficiency definition. For any heat engine, efficiency measures the fraction of input heat converted into net work: η=WoutQin=WoutQH\eta = \frac{W_{\text{out}}}{Q_{\text{in}}} = \frac{W_{\text{out}}}{Q_H}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Definition of Thermal Efficiency
  • η=WoutQH=QH−∣QC∣QH=1−∣QC∣QH\eta = \frac{W_{\text{out}}}{Q_H} = \frac{Q_H - |Q_C|}{Q_H} = 1 - \frac{|Q_C|}{Q_H}

  • Always divide net mechanical work output by the total heat energy absorbed from the hot source (QHQ_H), not the heat exhausted.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the heat absorbed by the engine from the high-temperature reservoir: QH=2.40×103 JQ_H = 2.40 \times 10^3\text{ J}.

  2. Divide net mechanical work output by heat input: η=720 J2400 J=0.300\eta = \frac{720\text{ J}}{2400\text{ J}} = 0.300.

Final answer

(a) η=0.300\eta = 0.300 (or 30.0%30.0\%); (b) ηCarnot=0.500\eta_{\text{Carnot}} = 0.500 (or 50.0%50.0\%); (c) ∣QC∣=1.68×103 J|Q_C| = 1.68 \times 10^3\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Remember the generic efficiency formula: efficiency is always useful outputtotal input paid for\frac{\text{useful output}}{\text{total input paid for}}.

  • When checking your answer, ensure that actual efficiency η\eta is strictly less than the Carnot efficiency ηCarnot\eta_{\text{Carnot}} for any real engine.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the temperature ratio in the Carnot efficiency formula, calculating T_H / T_C instead of T_C / T_H.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    η=WoutQH  ⟹  η=7202400=0.30\eta = \frac{W_{\text{out}}}{Q_H} \implies \eta = \frac{720}{2400} = 0.30

  2. Step 2

    ηCarnot=1−THTC  ⟹  ηCarnot=1−580290=1−2=−1\eta_{\text{Carnot}} = 1 - \frac{T_H}{T_C} \implies \eta_{\text{Carnot}} = 1 - \frac{580}{290} = 1 - 2 = -1

    Correct

    ηCarnot=1−TCTH=1−290 K580 K=0.500\eta_{\text{Carnot}} = 1 - \frac{T_C}{T_H} = 1 - \frac{290\text{ K}}{580\text{ K}} = 0.500

    You wrote the temperature fraction as THTC\frac{T_H}{T_C} instead of TCTH\frac{T_C}{T_H}. Because TH>TCT_H > T_C, this gave a fraction greater than 11 and a negative efficiency.

  3. Step 3

    |Q_C| = Q_H - W_{out\text{out}}   ⟹  \implies |Q_C| = 2400 - 720 = 1680 J\text{ J}_

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the definition of actual thermal efficiency as work output divided by heat input.

You correctly applied energy conservation to solve for the waste heat discharged per cycle.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted ratio in Carnot efficiency formula

No; you explicitly wrote down the inverted formula ηCarnot=1−THTC\eta_{\text{Carnot}} = 1 - \frac{T_H}{T_C} before substituting values.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You swapped the high-temperature reservoir THT_H and low-temperature reservoir TCT_C in the ratio. Efficiency represents the fraction of heat converted to work and must fall in the range 0<η<10 < \eta < 1. Because TC<THT_C < T_H, the fraction subtracted from 11 must be TCTH\frac{T_C}{T_H} to remain between 00 and 11.

REASONING PATH
Your ACEpath teacher’s suggested approach
Sanity Check on Efficiency Range
  • An engine's efficiency must always satisfy 0≤η<10 \le \eta < 1.

  • If your calculated efficiency is negative or greater than 11, immediately check whether you inverted a ratio or mixed up work and heat.

Carnot Efficiency Temperature Placement
  • Carnot efficiency is defined as ηCarnot=1−TCTH=TH−TCTH\eta_{\text{Carnot}} = 1 - \frac{T_C}{T_H} = \frac{T_H - T_C}{T_H}, where both temperatures are in Kelvin.

  • Remember that the smaller absolute temperature (TCT_C) always goes in the numerator so that the ratio TCTH<1\frac{T_C}{T_H} < 1.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute the absolute reservoir temperatures: ηCarnot=1−290 K580 K\eta_{\text{Carnot}} = 1 - \frac{290\text{ K}}{580\text{ K}}.

  2. Evaluate the temperature ratio: 290580=0.500\frac{290}{580} = 0.500.

  3. Subtract from 11: ηCarnot=1−0.500=0.500=50.0%\eta_{\text{Carnot}} = 1 - 0.500 = 0.500 = 50.0\%.

Final answer

(a) η=0.300\eta = 0.300 (30.0%30.0\%); (b) ηCarnot=0.500\eta_{\text{Carnot}} = 0.500 (50.0%50.0\%); (c) ∣QC∣=1.68×103 J|Q_C| = 1.68 \times 10^3\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the algebraic derivation of Carnot efficiency from η=1−∣QC∣QH\eta = 1 - \frac{|Q_C|}{Q_H} and the reversible relation ∣QC∣QH=TCTH\frac{|Q_C|}{Q_H} = \frac{T_C}{T_H}.

  • Practice checking that theoretical efficiencies always stay between 00 and 11 as a quick self-validation step.

OverviewACEpath Teacher's Diagnosis

03 The student misapplies conservation of energy by adding work to the absorbed heat rather than subtracting it to find the rejected waste heat.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    η=WoutQH  ⟹  η=7202400=0.30\eta = \frac{W_{\text{out}}}{Q_H} \implies \eta = \frac{720}{2400} = 0.30

  2. Step 2

    ηCarnot=1−TCTH  ⟹  ηCarnot=1−290580=0.50\eta_{\text{Carnot}} = 1 - \frac{T_C}{T_H} \implies \eta_{\text{Carnot}} = 1 - \frac{290}{580} = 0.50

  3. Step 3

    |Q_C| = Q_H + W_{out\text{out}}   ⟹  \implies |Q_C| = 2400 + 720 = 3120 J\text{ J}_

    Correct

    |Q_C| = Q_H - W_{out\text{out}} = 2400 J\text{ J} - 720 J\text{ J} = 1680 J\text{ J} = 1.68 ×\times 10^3 J\text{ J}_

    In a cyclic heat engine, the absorbed heat QHQ_H is the total energy input that splits into useful work WoutW_{\text{out}} and discarded waste heat ∣QC∣|Q_C|, meaning QH=Wout+∣QC∣Q_H = W_{\text{out}} + |Q_C|. Therefore, ∣QC∣=QH−Wout|Q_C| = Q_H - W_{\text{out}}, which gives 1680 J1680\text{ J} rather than 3120 J3120\text{ J}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recalled and evaluated the formula for thermal efficiency η=WoutQH\eta = \frac{W_{\text{out}}}{Q_H}.

You correctly applied the Carnot efficiency formula using temperatures in Kelvin.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Energy conservation sign error in heat engine cycle

You wrote ∣QC∣=QH+Wout|Q_C| = Q_H + W_{\text{out}} instead of ∣QC∣=QH−Wout|Q_C| = Q_H - W_{\text{out}}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You inverted the energy balance relation by treating mechanical work as an additional thermal energy input rather than a portion of the incoming heat QHQ_H converted into useful output.

REASONING PATH
Your ACEpath teacher’s suggested approach
First Law Energy Balance for a Cyclic Heat Engine
  • Over a complete cycle, ΔU=0\Delta U = 0, so total energy entering must equal total energy leaving: QH=Wout+∣QC∣Q_H = W_{\text{out}} + |Q_C|.

  • Always set up the input-output balance first (Qin=EoutQ_{\text{in}} = E_{\text{out}}) before rearranging for ∣QC∣|Q_C|.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the First Law of Thermodynamics for a complete cycle: QH=Wout+∣QC∣Q_H = W_{\text{out}} + |Q_C|.

  2. Rearrange for waste heat: ∣QC∣=QH−Wout|Q_C| = Q_H - W_{\text{out}}.

  3. Substitute the given values: ∣QC∣=2400 J−720 J=1680 J=1.68×103 J|Q_C| = 2400\text{ J} - 720\text{ J} = 1680\text{ J} = 1.68 \times 10^3\text{ J}.

Final answer

(a) η=0.300\eta = 0.300; (b) ηCarnot=0.500\eta_{\text{Carnot}} = 0.500; (c) ∣QC∣=1.68×103 J|Q_C| = 1.68 \times 10^3\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review energy flow diagrams (Sankey diagrams) for heat engines to visually anchor how input heat splits into work and exhaust heat.

  • Practice writing the conservation statement Ein=EoutE_{\text{in}} = E_{\text{out}} before isolating unknown quantities.

Lock it in

Similar question

01

A heat engine absorbs 5.00×103 J5.00 \times 10^3\text{ J} of heat from a hot reservoir and expels 3.50×103 J3.50 \times 10^3\text{ J} of waste heat to an exhaust sink during each cycle. Find: (a) the net work output WoutW_{\text{out}} per cycle, and (b) the thermal efficiency η\eta.

Answer

(a) Wout=QH−∣QC∣=5000 J−3500 J=1500 J=1.50×103 JW_{\text{out}} = Q_H - |Q_C| = 5000\text{ J} - 3500\text{ J} = 1500\text{ J} = 1.50 \times 10^3\text{ J}. (b) η=WoutQH=1500 J5000 J=0.300 (or 30.0%)\eta = \frac{W_{\text{out}}}{Q_H} = \frac{1500\text{ J}}{5000\text{ J}} = 0.300\text{ (or } 30.0\%\text{)}.

02

A steam turbine operates between TH=600 KT_H = 600\text{ K} and TC=300 KT_C = 300\text{ K}. It delivers 1.80×104 J1.80 \times 10^4\text{ J} of net work while operating at an actual efficiency equal to 60%60\% of its theoretical Carnot maximum efficiency. Calculate: (a) the Carnot efficiency ηCarnot\eta_{\text{Carnot}}, (b) the actual efficiency η\eta, and (c) the heat absorbed QHQ_H per cycle.

Answer

(a) ηCarnot=1−TCTH=1−300600=0.500 (or 50.0%)\eta_{\text{Carnot}} = 1 - \frac{T_C}{T_H} = 1 - \frac{300}{600} = 0.500\text{ (or } 50.0\%\text{)}. (b) η=0.60×0.500=0.300 (or 30.0%)\eta = 0.60 \times 0.500 = 0.300\text{ (or } 30.0\%\text{)}. (c) QH=Woutη=1.80×104 J0.300=6.00×104 JQ_H = \frac{W_{\text{out}}}{\eta} = \frac{1.80 \times 10^4\text{ J}}{0.300} = 6.00 \times 10^4\text{ J}.

03

An engineer claims to have designed a cyclic engine operating between TH=800 KT_H = 800\text{ K} and TC=400 KT_C = 400\text{ K} that exhausts ∣QC∣=1200 J|Q_C| = 1200\text{ J} of heat while producing Wout=1500 JW_{\text{out}} = 1500\text{ J} of work per cycle. Determine: (a) the claimed thermal efficiency ηclaimed\eta_{\text{claimed}}, (b) the Carnot efficiency limit ηCarnot\eta_{\text{Carnot}}, and (c) whether this claim violates the Second Law of Thermodynamics.

Answer

(a) Heat absorbed is QH=Wout+∣QC∣=1500 J+1200 J=2700 JQ_H = W_{\text{out}} + |Q_C| = 1500\text{ J} + 1200\text{ J} = 2700\text{ J}. Therefore, ηclaimed=WoutQH=15002700=59≈0.556 (or 55.6%)\eta_{\text{claimed}} = \frac{W_{\text{out}}}{Q_H} = \frac{1500}{2700} = \frac{5}{9} \approx 0.556\text{ (or } 55.6\%\text{)}. (b) ηCarnot=1−400 K800 K=0.500 (or 50.0%)\eta_{\text{Carnot}} = 1 - \frac{400\text{ K}}{800\text{ K}} = 0.500\text{ (or } 50.0\%\text{)}. (c) Yes, the claim is physically impossible and violates the Second Law because ηclaimed(55.6%)>ηCarnot(50.0%)\eta_{\text{claimed}} (55.6\%) > \eta_{\text{Carnot}} (50.0\%).

Loading workspace…