Resources
Two blocks connected by a light string are sliding along a rough horizontal table. A pulling force is applied horizontally to the lead block of mass , which trails behind it a second block of unknown mass . Both blocks have the same coefficient of kinetic friction with the table surface, . If the tension in the cord between the two blocks is measured to be during the motion, and , calculate the mass of the trailing block.
Answer and steps
Final answer
Steps
Analyze the forces acting on the lead block ()
Both blocks accelerate together horizontally to the right with a common acceleration .
For the lead block of mass :
- Vertically, the normal force balances the weight: .
- The friction force opposing motion is:
- Horizontally, the forward applied force is , and the backward forces are the tension and the friction force .
Applying Newton's second law to block :
Substitute the known values to find the acceleration:
Apply Newton's second law to the trailing block ()
For the trailing block of mass :
- Vertically, the normal force is .
- The friction force opposing motion is:
- Horizontally, the forward force pulling it is the cord tension , and the opposing force is friction .
Applying Newton's second law to block :
Solve for the unknown mass
Rearrange the equation to factor out :
Substitute the values:
Common Pitfall: Do not set the tension equal only to the friction force . Because the system is accelerating, the cord tension must overcome kinetic friction and provide the net force required to accelerate block at .
Typical errors
01 The student forgets that kinetic friction acts on the trailing block, setting T = m1 a while including friction on the lead block or total system.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You omitted the kinetic friction force acting on block . Since both blocks slide on the rough surface, the net horizontal force on the trailing block is , not just .
- Step 3Correct
This quadratic equation arises from substituting the incorrect expression for . If you instead isolate the lead block , you can solve for directly: .
- Step 4Correct
The negative discriminant is a direct consequence of the missing friction term in Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly included kinetic friction for both masses when writing the system-level equation.
You correctly related the system acceleration to individual block dynamics.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou forgot that friction acts independently on every surface in contact with the table, treating the trailing block as if it were sliding on a frictionless surface.
REASONING PATH
Your ACEpath teacher’s suggested approach- Individual Free-Body Diagrams
Every body in contact with a rough surface experiences its own friction force .
Draw a separate free-body diagram for each block and verify that all contact forces (friction, normal, tension) are included before writing .
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite Newton's second law for the lead block : .
Substitute the known values to find the acceleration: .
Write Newton's second law for the trailing block including friction: .
Rearrange for : .
02 The student assumes the blocks move at constant velocity, setting the net force on the trailing block to zero as T - μk m1 g = 0.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You set the net horizontal force on block equal to zero. Because the system is accelerating, Newton's second law requires . You first need to find the common acceleration using the lead block .
- Step 2Correct
Your algebraic substitution and arithmetic were carried out accurately, but the result was altered by omitting the acceleration term from the denominator.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified tension and kinetic friction as the opposing horizontal forces on the trailing block.
You accurately calculated the frictional acceleration factor and completed the division correctly.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the trailing block as being in static or constant-velocity equilibrium () rather than part of an accelerating system.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating dynamic motion with dynamic equilibrium. When connected objects slide under an applied force that exceeds friction, the cord tension must overcome kinetic friction and provide the mass with acceleration ().
REASONING PATH
Your ACEpath teacher’s suggested approach- System Acceleration Check
Never assume unless the problem explicitly specifies constant velocity or equilibrium.
Write for each connected body and check whether the applied external forces exceed total friction.
- Equation Coupling
In connected systems, the common acceleration links the motion equations of all blocks.
Solve for the unknown acceleration from the body with fully known parameters before solving for unknown masses.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply Newton's second law horizontally to the lead block :
Substitute known values:
Apply Newton's second law to the trailing block:
Rearrange for :
03 The student misidentifies the lead block as the only one experiencing friction, subtracting the full friction force only from m2 when calculating system acceleration.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You treated the cord tension as the only horizontal force acting on . Since both blocks slide on the rough surface with coefficient , a backward friction force also opposes the motion of .
WHAT YOU DID WELL
Compliments from Your TeacherYou drew up a complete force balance for the lead block including applied force, tension, and kinetic friction.
You calculated the correct numerical acceleration of the two-block system as .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou forgot that the rough surface exerts a kinetic friction force on every object in contact with it, leading to an incomplete free-body diagram for the trailing block.
REASONING PATH
Your ACEpath teacher’s suggested approach- Free-Body Diagram Check
Every object sliding across a rough surface experiences its own kinetic friction force .
Always draw individual free-body diagrams for each block and verify that friction opposes motion on every surface contact.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the horizontal equation of motion for block : .
Substitute : .
Factor out : .
Substitute the values , , and : .
Lock it in
A block of mass slides across a rough horizontal surface with friction coefficient , pulled forward by a cord with tension . What is the horizontal equation of motion?
. Friction always opposes the sliding motion and must be subtracted from the forward pull.
Similar question
A single block of mass is pulled along a rough horizontal table by a horizontal string with tension . If and , find the acceleration of the block.
Answer
. Calculate friction: . Apply Newton's second law: .
Two blocks with masses and are connected by a light cord on a rough horizontal floor (). A horizontal force pulls block forward. Taking , find the cord tension between the blocks.
Answer
. Total mass . Total friction . Acceleration . For trailing block : .
Two blocks of masses and are connected by a light string on an incline of angle with . A pulling force pulls up the incline. If the tension between the blocks is , find the mass of the trailing block ().
Answer
. For lead block : . Substituting values: . For trailing block : (with unrounded values, ).