Resources
A delivery package of mass slides down a curved warehouse ramp. The package is released from an initial height of above the base with an unknown initial speed . Non-conservative friction forces between the package and the ramp dissipate of thermal energy during the slide. Upon reaching the flat horizontal base of the ramp (), the package has a measured speed of . Using the Work-Energy Theorem with , determine the initial speed with which the package was launched at the top of the ramp.
Answer and steps
Final answer
Steps
Identify the System and the Work-Energy Principle
According to the Work-Energy Theorem, the work done by all non-conservative forces equals the change in the total mechanical energy of the system:
Here:
- Initial state (): at the top of the ramp (, speed ).
- Final state (): at the bottom of the ramp (, speed ).
- Non-conservative friction force dissipates energy, so the work done by friction is negative:
Express Total Mechanical Energy at Both States
Define the horizontal base of the ramp as the reference level for gravitational potential energy ( at ).
- Initial mechanical energy ():
- Final mechanical energy ():
Set Up the Energy Balance Equation
Substitute and into the energy relation :
Rearrange to solve for the initial kinetic energy :
Since , this becomes:
Calculate the Numerical Values
Given values:
Compute each energy term:
- Final kinetic energy:
- Initial gravitational potential energy:
Substitute these values to find the initial kinetic energy:
Solve for the Initial Speed
Isolate :
(Pitfall to avoid: Be sure to assign a negative sign to the work done by friction, . Friction opposes motion and removes mechanical energy from the system, converting it into thermal energy.)
Typical errors
01 The student treats work done by friction as positive energy added rather than dissipated energy removed from mechanical energy, leading to an incorrect initial speed of 1.25 m/s.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
() m v_i^2 + m g h + 185 = () m v_f^2 0.5 12.0 v_i^2 + 12.0 9.80 3.60 + 185 = 0.5 12.0 (7.40)^2
CorrectFriction opposes motion and dissipates mechanical energy into thermal energy, so the work done by friction is negative (). You added to the initial mechanical energy, which incorrectly treats friction as adding mechanical energy rather than removing it.
- Step 2
6.0 v_i^2 + 423.36 + 185 = 328.56 6.0 v_i^2 + 608.36 = 328.56 6.0 v_i^2 = 608.36 - 328.56 = 279.8 v_i^2 = 46.63
CorrectWhen solving , subtracting from both sides yields a negative value (). You reversed the subtraction order to to keep the value positive.
- Step 3
v_i = 6.83
CorrectYou calculated the square root of correctly, but the numerical value is carried over from the earlier sign and algebraic errors.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the expressions for kinetic energy and gravitational potential energy.
You correctly calculated the numerical values of the potential energy () and final kinetic energy ().
You correctly extracted the square root in your final calculation step.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou reversed the subtraction order from to to avoid a negative result for .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated dissipated thermal energy as mechanical energy added to the initial state instead of using with (or ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Work of friction is negative
Frictional forces oppose sliding motion, so .
Always write or when thermal energy is dissipated.
- Negative kinetic energy sanity check
Kinetic energy can never be negative for real velocities.
If your equation yields , stop and inspect the signs in your energy conservation equation rather than flipping the terms.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply the work-energy theorem with dissipated energy:
Substitute the energies:
Simplify the terms:
Isolate : (or before intermediate rounding)
Take the square root:
02 The student forgets to square the velocity in the kinetic energy terms, writing (1/2)m*v instead of (1/2)m*v².
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
() m * v_i + m * g * h - 185 = () m * v_f
CorrectYou correctly set up the energy balance with gravitational potential energy and dissipated thermal energy, but kinetic energy is defined as , not .
- Step 2
0.5 * 12.0 * v_i + 12.0 * 9.80 * 3.60 - 185 = 0.5 * 12.0 * 7.40 6.0 * v_i + 238.36 = 44.4 6.0 * v_i = -193.96
CorrectYour algebraic simplification followed your equation correctly, but the values were affected by missing the squared exponent on the velocity terms.
- Step 3
v_i = -32.3
CorrectBecause of the missing square in the kinetic energy terms, you obtained a negative speed rather than solving for .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly included all relevant energy forms: initial kinetic energy, gravitational potential energy, and final kinetic energy.
You properly subtracted the dissipated thermal energy () from the initial mechanical energy.
You executed the multi-step linear algebra and arithmetic cleanly according to your setup.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou wrote kinetic energy as instead of . Missing the exponent on velocity turns a quadratic energy equation into a linear expression with incorrect units (momentum units instead of energy units ), which led to an unphysical negative speed.
REASONING PATH
Your ACEpath teacher’s suggested approach- Kinetic Energy Formula Definition
Kinetic energy is quadratic in speed: .
Always verify that velocity is squared so that the unit matches energy: .
- Sanity Check on Sign of Speed
Speed is a magnitude and must always be non-negative ().
If an energy calculation yields a negative speed or a negative kinetic energy, pause and re-check your formula setups and energy signs.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the Work-Energy Theorem with quadratic kinetic energy terms: .
Substitute the known values: .
Compute each term: .
Isolate : .
Take the square root: .
03 The student ignores the work done by friction completely, assuming conservation of total mechanical energy.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You assumed total mechanical energy is conserved, but friction dissipates of mechanical energy along the slide. The work-energy principle requires including the work done by non-conservative forces: .
- Step 2Correct
Because friction was omitted in the initial energy balance, the right-hand side resulted in a negative value (), which you made positive by dropping the negative sign.
- Step 3Correct
Your square root calculation was carried out correctly on your intermediate value, but the result is affected by the missing friction term.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified and applied the formulas for kinetic energy and gravitational potential energy.
You accurately calculated the numerical values for the final kinetic energy () and initial potential energy ().
You successfully isolated the variable algebraically and took the square root.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeDropping the negative sign when solving .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou assumed total mechanical energy is conserved () instead of applying the extended Work-Energy Theorem () when non-conservative dissipative forces like friction are present.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify Non-Conservative Forces
Whenever friction, drag, or applied forces act along a path, mechanical energy is not conserved: or .
Scan the problem statement for dissipated energy or friction forces and include in your initial energy balance.
- Heed Negative Kinetic Energy Warnings
Kinetic energy and squared real velocities must be non-negative.
If an algebraic step yields , treat it as an immediate signal that an energy term or sign in the setup is missing or inverted, rather than discarding the negative sign.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the complete work-energy balance including friction: , where .
Substitute the computed values: .
Simplify the constant terms: .
Isolate : .
Take the square root to find : .
Lock it in
In the work-energy relation , what is the sign of for kinetic friction?
Negative (). Friction opposes motion and takes mechanical energy out of the system.
Similar question
A crate slides down a rough incline from a height of above the ground. It starts from rest and reaches the bottom with a speed of . Using , how much thermal energy was dissipated by friction?
Answer
. Key steps: ; ; .
A toy car is launched up an incline with an initial speed of . It travels up to a vertical height of before momentarily coming to rest. Using , determine the work done by friction on the car.
Answer
. Key steps: ; ; .
A sled slides down a high hill with an initial speed of . Along the hill, friction does of work. At the bottom, the sled encounters a spring with spring constant on a frictionless horizontal surface. Using , find the maximum compression of the spring.
Answer
. Key steps: ; ; set .