Resources

In a physics laboratory standardization experiment, a student determines the internal resistance rr and electromotive force Ex\mathcal{E}_x of an unknown cell using a potentiometer-inspired multi-loop setup. A known working accumulator E0=6.000 V\mathcal{E}_0 = 6.000\text{ V} with negligible internal resistance is placed across a uniform slide wire of total length L=100.0 cmL = 100.0\text{ cm} and total resistance Rw=20.00 ΩR_w = 20.00\ \Omega. The unknown test branch containing cell Ex\mathcal{E}_x with series internal resistance rr is connected between the zero-end of the wire and a sliding contact tapping off length xx. A sensitive galvanometer in the test branch detects zero current (Ig=0.000 AI_g = 0.000\text{ A}) precisely when the contact is set at x1=35.00 cmx_1 = 35.00\text{ cm}. When a standard shunt resistor Rs=4.000 ΩR_s = 4.000\ \Omega is placed in parallel directly across the terminals of the test cell, the balance point shifts to x2=28.00 cmx_2 = 28.00\text{ cm}. Using Kirchhoff's loop and junction principles under null-balance conditions, calculate the internal resistance rr of the cell.

Answer and steps

Final answer

r=1.000 Ωr = 1.000\ \Omega

Steps

01

Analyze the Primary Circuit and Potential Gradient

The primary circuit consists of the working accumulator E0=6.000 V\mathcal{E}_0 = 6.000\text{ V} connected across a uniform wire of length L=100.0 cmL = 100.0\text{ cm} and resistance Rw=20.00 ΩR_w = 20.00\ \Omega.

Because the accumulator has negligible internal resistance, the full potential difference across the wire is Vw=E0=6.000 VV_w = \mathcal{E}_0 = 6.000\text{ V}. Since the wire is uniform, the potential drop per unit length (potential gradient kk) is constant:

k=VwL=E0Lk = \frac{V_w}{L} = \frac{\mathcal{E}_0}{L}

The potential difference across any segment of length xx measured from the zero-end is:

V(x)=k⋅xV(x) = k \cdot x


02

Condition 1: Unshunted Cell (Open Circuit at Null)

In the first measurement, the test branch containing cell Ex\mathcal{E}_x, internal resistance rr, and the galvanometer is balanced at length x1=35.00 cmx_1 = 35.00\text{ cm}.

  • At null balance, the galvanometer current is Ig=0 AI_g = 0\text{ A}.
  • By Kirchhoff's junction rule, no current flows anywhere in the secondary branch, meaning no current is drawn from cell Ex\mathcal{E}_x.
  • Applying Kirchhoff's loop rule to the secondary loop containing wire segment x1x_1, the galvanometer, and cell Ex\mathcal{E}_x:

V(x1)−Igr−Ex=0V(x_1) - I_g r - \mathcal{E}_x = 0

Since Ig=0I_g = 0:

Ex=V(x1)=k⋅x1\mathcal{E}_x = V(x_1) = k \cdot x_1


03

Condition 2: Shunted Cell (Closed Local Loop)

A shunt resistor Rs=4.000 ΩR_s = 4.000\ \Omega is now connected in parallel directly across the terminals of the test cell. A new balance is obtained at length x2=28.00 cmx_2 = 28.00\text{ cm}.

  • At the balance point, the galvanometer current connecting the test circuit to the slide wire is again zero (Ig=0 AI_g = 0\text{ A}).
  • Because no current enters or leaves via the tapping contact, the current IlocalI_{\text{local}} circulating through the local closed loop formed by Ex\mathcal{E}_x, rr, and RsR_s is determined by Kirchhoff's loop rule for that isolated loop:

Ex−Ilocalr−IlocalRs=0  ⟹  Ilocal=ExRs+r\mathcal{E}_x - I_{\text{local}} r - I_{\text{local}} R_s = 0 \implies I_{\text{local}} = \frac{\mathcal{E}_x}{R_s + r}

  • The potential difference across the terminal of this shunted combination is the voltage across the shunt resistor RsR_s:

Vt=IlocalRs=ExRsRs+rV_t = I_{\text{local}} R_s = \frac{\mathcal{E}_x R_s}{R_s + r}

  • Applying Kirchhoff's loop rule across the tapped slide-wire segment of length x2x_2 and the shunted cell combination:

V(x2)=Vt  ⟹  k⋅x2=ExRsRs+rV(x_2) = V_t \implies k \cdot x_2 = \frac{\mathcal{E}_x R_s}{R_s + r}


04

Solve for the Internal Resistance rr

Divide the equation for Ex\mathcal{E}_x by the equation for VtV_t:

ExVt=k⋅x1k⋅x2=x1x2\frac{\mathcal{E}_x}{V_t} = \frac{k \cdot x_1}{k \cdot x_2} = \frac{x_1}{x_2}

Substitute Vt=ExRsRs+rV_t = \frac{\mathcal{E}_x R_s}{R_s + r}:

ExExRsRs+r=Rs+rRs=1+rRs\frac{\mathcal{E}_x}{\frac{\mathcal{E}_x R_s}{R_s + r}} = \frac{R_s + r}{R_s} = 1 + \frac{r}{R_s}

Equating this to the length ratio gives:

1+rRs=x1x2  ⟹  rRs=x1−x2x21 + \frac{r}{R_s} = \frac{x_1}{x_2} \implies \frac{r}{R_s} = \frac{x_1 - x_2}{x_2}

r=Rs(x1−x2x2)r = R_s \left(\frac{x_1 - x_2}{x_2}\right)

Substitute the given numerical values:

r=4.000 Ω⋅(35.00 cm−28.00 cm28.00 cm)=4.000⋅(7.0028.00)=4.000⋅14=1.000 Ωr = 4.000\ \Omega \cdot \left(\frac{35.00\text{ cm} - 28.00\text{ cm}}{28.00\text{ cm}}\right) = 4.000 \cdot \left(\frac{7.00}{28.00}\right) = 4.000 \cdot \frac{1}{4} = 1.000\ \Omega

(Common Pitfall: Do not divide by the unshunted length x1x_1 in the denominator; the terminal voltage across RsR_s corresponds directly to x2x_2, making x2x_2 the correct reference denominator).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student inverts the ratio of the balancing lengths when applying the potentiometer internal resistance formula, computing r = Rs * (1 - x2 / x1) or inverted ratio.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Ex=x1L⋅E0=35.00100.0⋅6.000=2.100 V\mathcal{E}_x = \frac{x_1}{L} \cdot \mathcal{E}_0 = \frac{35.00}{100.0} \cdot 6.000 = 2.100\text{ V}

  2. Step 2

    V=x2L⋅E0=28.00100.0⋅6.000=1.680 VV = \frac{x_2}{L} \cdot \mathcal{E}_0 = \frac{28.00}{100.0} \cdot 6.000 = 1.680\text{ V}

  3. Step 3

    r=Rs⋅(x2x1)r = R_s \cdot \left(\frac{x_2}{x_1}\right)

    Correct

    r=Rs(x1−x2x2)r = R_s \left(\frac{x_1 - x_2}{x_2}\right) or r=Rs(Ex−VV)r = R_s \left(\frac{\mathcal{E}_x - V}{V}\right)

    You equated rr directly to Rs⋅x2x1R_s \cdot \frac{x_2}{x_1}. In a closed circuit with a shunt resistor, terminal voltage is V=Ex−Ir=IRsV = \mathcal{E}_x - I r = I R_s, which gives ExV=1+rRs=x1x2\frac{\mathcal{E}_x}{V} = 1 + \frac{r}{R_s} = \frac{x_1}{x_2}, leading to r=Rs(x1−x2x2)r = R_s \left(\frac{x_1 - x_2}{x_2}\right).

  4. Step 4

    r=4.000⋅(28.0035.00)=3.200 Ωr = 4.000 \cdot \left(\frac{28.00}{35.00}\right) = 3.200\ \Omega

    Correct

    r=4.000 Ω⋅(35.00−28.0028.00)=1.000 Ωr = 4.000\ \Omega \cdot \left(\frac{35.00 - 28.00}{28.00}\right) = 1.000\ \Omega

    This numerical calculation directly followed your incorrect formula from step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the uniform potential gradient across the slide wire to relate balance lengths to loop voltages.

You calculated the open-circuit cell EMF and the closed-circuit terminal voltage accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Misrecollection / Circuit Loop Relationship

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You recalled a simple ratio of balancing lengths rather than applying Ohm's law and Kirchhoff's loop rule to the shunted cell's local loop, omitting the subtraction of terminal voltage from EMF.

REASONING PATH
Your ACEpath teacher’s suggested approach
Local Loop Current
  • Ilocal=ExRs+rI_{\text{local}} = \frac{\mathcal{E}_x}{R_s + r}

  • Apply Kirchhoff's voltage law around the secondary loop containing the cell and shunt resistor.

Terminal Voltage to Length Ratio
  • ExV=x1x2=Rs+rRs=1+rRs\frac{\mathcal{E}_x}{V} = \frac{x_1}{x_2} = \frac{R_s + r}{R_s} = 1 + \frac{r}{R_s}

  • Express the ratio of lengths as x1x2\frac{x_1}{x_2} and solve algebraically for rr, noting that x1>x2x_1 > x_2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the voltage ratio from the local loop: ExV=I(Rs+r)IRs=1+rRs\frac{\mathcal{E}_x}{V} = \frac{I(R_s + r)}{I R_s} = 1 + \frac{r}{R_s}.

  2. Substitute the balancing lengths: 1+rRs=x1x2  ⟹  rRs=x1−x2x21 + \frac{r}{R_s} = \frac{x_1}{x_2} \implies \frac{r}{R_s} = \frac{x_1 - x_2}{x_2}.

  3. Substitute the values: r=4.000 Ω⋅(35.00 cm−28.00 cm28.00 cm)=4.000 Ω⋅7.0028.00=1.000 Ωr = 4.000\ \Omega \cdot \left(\frac{35.00\text{ cm} - 28.00\text{ cm}}{28.00\text{ cm}}\right) = 4.000\ \Omega \cdot \frac{7.00}{28.00} = 1.000\ \Omega.

Final answer

r=1.000 Ωr = 1.000\ \Omega

NEXT STEPS
Final Takeaways from Your Teacher
  • Always derive potentiometer formulas from first principles using Kirchhoff's loop rules rather than memorizing bare ratios.

  • Check that your formula yields r=0r = 0 when x1=x2x_1 = x_2 (an ideal cell with zero internal resistance has no voltage drop when shunted).

OverviewACEpath Teacher's Diagnosis

02 The student confuses the terminal voltage across the shunt with the voltage drop across the internal resistance alone, setting V = I * r instead of V = I * Rs.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Ex=(35.00/100.0)×6.000=2.100 V  ⟹  V=(28.00/100.0)×6.000=1.680 V\mathcal{E}_x = (35.00 / 100.0) \times 6.000 = 2.100\text{ V} \implies V = (28.00 / 100.0) \times 6.000 = 1.680\text{ V}

  2. Step 2

    V=Ex×rRs+r  ⟹  1.680=2.100×r4.000+rV = \mathcal{E}_x \times \frac{r}{R_s + r} \implies 1.680 = \frac{2.100 \times r}{4.000 + r}

    Correct

    Vt=Ex×RsRs+r  ⟹  1.680=2.100×4.0004.000+rV_t = \mathcal{E}_x \times \frac{R_s}{R_s + r} \implies 1.680 = \frac{2.100 \times 4.000}{4.000 + r}

    The potentiometer taps off the cell's outer terminals, which are connected across the shunt resistor RsR_s. Therefore, the balanced voltage is the voltage across RsR_s, so the numerator in the voltage divider must be RsR_s, not rr.

  3. Step 3

    1.680×(4.000+r)=2.100×r  ⟹  6.720=0.420×r1.680 \times (4.000 + r) = 2.100 \times r \implies 6.720 = 0.420 \times r

    Correct

    1.680×(4.000+r)=2.100×4.000  ⟹  6.720+1.680r=8.400  ⟹  1.680r=1.6801.680 \times (4.000 + r) = 2.100 \times 4.000 \implies 6.720 + 1.680r = 8.400 \implies 1.680r = 1.680

    Your algebraic clearing of fractions was executed correctly, but it followed from the incorrect voltage-divider setup in Step 2.

  4. Step 4

    r=16.00 Ωr = 16.00\ \Omega

    Correct

    r=1.000 Ωr = 1.000\ \Omega

    Because of the inverted voltage-divider formula, your final value for the internal resistance is incorrect.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the uniform potential gradient of the potentiometer wire to find the voltage for both lengths.

You correctly identified that the open-circuit balance corresponds to the full electromotive force Ex\mathcal{E}_x.

You performed accurate algebraic transformations when solving your equation for rr.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Terminal voltage vs internal drop confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You mistook the potential tapped by the potentiometer for the internal voltage loss IlocalrI_{\text{local}} r rather than the terminal voltage Vt=IlocalRsV_t = I_{\text{local}} R_s appearing across the external terminals.

REASONING PATH
Your ACEpath teacher’s suggested approach
Terminal Voltage of a Loaded Cell
  • When a cell supplies current through a closed local circuit, the measurable voltage across its external terminals is Vt=E−Ir=IRs=ERsRs+rV_t = \mathcal{E} - I r = I R_s = \mathcal{E} \frac{R_s}{R_s + r}.

  • Always place the external load resistance RsR_s in the numerator of the terminal voltage divider, never the hidden internal resistance rr.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Express the balanced terminal voltage across the shunt resistor: Vt=Ex(RsRs+r)V_t = \mathcal{E}_x \left(\frac{R_s}{R_s + r}\right).

  2. Substitute the known values: 1.680=2.100×(4.0004.000+r)1.680 = 2.100 \times \left(\frac{4.000}{4.000 + r}\right).

  3. Cross-multiply: 1.680(4.000+r)=8.400  ⟹  6.720+1.680r=8.4001.680(4.000 + r) = 8.400 \implies 6.720 + 1.680r = 8.400.

  4. Subtract 6.7206.720 from both sides: 1.680r=1.6801.680r = 1.680.

Final answer

r=1.000 Ωr = 1.000\ \Omega

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch the local closed loop formed by Ex\mathcal{E}_x, rr, and RsR_s to identify which component sits between the two test terminals.

  • Remember that a potentiometer balances external terminal potential differences, which equals IRsI R_s, not IrI r.

OverviewACEpath Teacher's Diagnosis

03 The student assumes that connecting the shunt draws current from the slide wire and forgets that the galvanometer current is zero at null balance, adding the slide wire resistance Rw into the shunt loop.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ExV=x1x2=35.0028.00=1.250\frac{\mathcal{E}_x}{V} = \frac{x_1}{x_2} = \frac{35.00}{28.00} = 1.250

  2. Step 2

    r=(Rs+Rw)⋅(x1x2−1)r = (R_s + R_w) \cdot \left(\frac{x_1}{x_2} - 1\right)

    Correct

    r=Rs(x1x2−1)r = R_s \left(\frac{x_1}{x_2} - 1\right)

    You added the slide-wire resistance RwR_w to the shunt resistance RsR_s. At null balance, no current passes through the galvanometer into or out of the potentiometer wire, so the wire resistance does not enter the closed shunt loop containing only the cell and RsR_s.

  3. Step 3

    r=(4.000+20.00)⋅(1.250−1)  ⟹  r=24.00⋅0.250=6.000 Ωr = (4.000 + 20.00) \cdot (1.250 - 1) \implies r = 24.00 \cdot 0.250 = 6.000\ \Omega

    Correct

    r=4.000 Ω⋅(1.250−1)=1.000 Ωr = 4.000\ \Omega \cdot (1.250 - 1) = 1.000\ \Omega

    Your arithmetic correctly followed your formula from Step 2, but the final value was affected by including RwR_w.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the ratio of balancing lengths equals the ratio of open-circuit emf to closed-circuit terminal voltage.

You performed the fractional arithmetic and evaluation accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Misapplying loop rules at null balance

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that the slide-wire resistance forms part of the discharge circuit for the test cell, overlooking that zero galvanometer deflection completely isolates the shunted cell's local current from the potentiometer wire.

REASONING PATH
Your ACEpath teacher’s suggested approach
Null-Current Isolation
  • At null condition, Ig=0I_g = 0, meaning no current flows between the primary wire circuit and the secondary test branch.

  • Analyze the shunted cell as an independent loop containing only Ex\mathcal{E}_x, rr, and RsR_s when computing the terminal voltage VtV_t.

Internal Resistance Formula
  • Vt=ExRsRs+r  ⟹  ExVt=1+rRsV_t = \frac{\mathcal{E}_x R_s}{R_s + r} \implies \frac{\mathcal{E}_x}{V_t} = 1 + \frac{r}{R_s}.

  • Equate 1+rRs1 + \frac{r}{R_s} directly to x1x2\frac{x_1}{x_2}, yielding r=Rs(x1−x2x2)r = R_s \left(\frac{x_1 - x_2}{x_2}\right) with no dependence on wire resistance RwR_w.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the terminal voltage across the shunt: Vt=ExRsRs+rV_t = \frac{\mathcal{E}_x R_s}{R_s + r}.

  2. Relate the ratio of balance lengths to the voltages: x1x2=ExVt=1+rRs\frac{x_1}{x_2} = \frac{\mathcal{E}_x}{V_t} = 1 + \frac{r}{R_s}.

  3. Solve for rr: r=Rs(x1x2−1)=4.000 Ω⋅(1.250−1)=1.000 Ωr = R_s \left(\frac{x_1}{x_2} - 1\right) = 4.000\ \Omega \cdot (1.250 - 1) = 1.000\ \Omega.

Final answer

r=1.000 Ωr = 1.000\ \Omega

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how Kirchhoff's junction rule ensures the secondary loop current remains self-contained when the galvanometer reads zero.

  • Practice deriving the internal resistance expression directly from the two loop equations rather than memorizing resistance combinations.

Lock it in

Similar question

01

A cell of unknown internal resistance rr balances against 40.0 cm40.0\text{ cm} of a potentiometer wire on open circuit. When shunted by a 6.00 Ω6.00\ \Omega resistor, the null point shifts to 30.0 cm30.0\text{ cm}. Calculate rr.

Answer

r=2.00 Ωr = 2.00\ \Omega. Using r=Rs(x1−x2x2)=6.00(40.0−30.030.0)=6.00⋅10.030.0=2.00 Ωr = R_s \left(\frac{x_1 - x_2}{x_2}\right) = 6.00\left(\frac{40.0 - 30.0}{30.0}\right) = 6.00 \cdot \frac{10.0}{30.0} = 2.00\ \Omega.

02

A potentiometer setup balances an open-circuit cell at x1=75.0 cmx_1 = 75.0\text{ cm}. When a shunt resistor Rs=10.0 ΩR_s = 10.0\ \Omega is connected across the cell, the balancing length decreases by 15.0 cm15.0\text{ cm}. Find the cell's internal resistance rr.

Answer

r=2.50 Ωr = 2.50\ \Omega. The shunted balance length is x2=75.0 cm−15.0 cm=60.0 cmx_2 = 75.0\text{ cm} - 15.0\text{ cm} = 60.0\text{ cm}. Then r=Rs(x1−x2x2)=10.0(75.0−60.060.0)=10.0⋅15.060.0=2.50 Ωr = R_s \left(\frac{x_1 - x_2}{x_2}\right) = 10.0\left(\frac{75.0 - 60.0}{60.0}\right) = 10.0 \cdot \frac{15.0}{60.0} = 2.50\ \Omega.

03

A cell with Ex=1.50 V\mathcal{E}_x = 1.50\text{ V} and internal resistance r=2.00 Ωr = 2.00\ \Omega balances at length x1x_1 on a potentiometer. When shunted by a standard resistor RsR_s, the new balance length is x2=0.800⋅x1x_2 = 0.800 \cdot x_1. Find the resistance value of RsR_s.

Answer

Rs=8.00 ΩR_s = 8.00\ \Omega. From x1x2=1+rRs\frac{x_1}{x_2} = 1 + \frac{r}{R_s}, substitute x1x2=10.800=1.25\frac{x_1}{x_2} = \frac{1}{0.800} = 1.25. Thus, 1+2.00Rs=1.25  ⟹  2.00Rs=0.25  ⟹  Rs=2.000.25=8.00 Ω1 + \frac{2.00}{R_s} = 1.25 \implies \frac{2.00}{R_s} = 0.25 \implies R_s = \frac{2.00}{0.25} = 8.00\ \Omega.

Loading workspace…