Resources
A sled carrying scientific equipment is pulled along a flat, horizontal surface of packed snow across a straight displacement of by a constant tension force of . The tension does a total of of mechanical work on the sled during this displacement. Determine the angle that the tow line makes relative to the horizontal.
Answer and steps
Final answer
Steps
Step 1: Relate work, force, and angle
The work done by a constant force of magnitude acting on an object over a displacement of magnitude is given by:
where:
- is the magnitude of the applied tension force,
- is the magnitude of the displacement along the horizontal surface,
- is the angle between the tension force vector and the direction of displacement (here, the horizontal direction).
Only the component of tension parallel to the displacement, , does mechanical work.
Step 2: Solve for
Rearrange the work equation to isolate :
Substitute the given numerical values:
Calculate the denominator:
Now evaluate the fraction:
Step 3: Calculate the angle
Take the inverse cosine () of both sides:
Rounding to three significant figures gives:
Common Pitfall: Always verify whether the angle is measured relative to the horizontal or the vertical. If an angle is given or requested relative to the vertical, the parallel component would involve instead of . Here, because the towing line is measured relative to the horizontal displacement, is the correct trigonometric function.
Typical errors
01 The student uses sin(θ) instead of cos(θ) when setting up the work formula, confusing the horizontal force component with the vertical component.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Work is defined as the scalar product , where is the angle between the force vector and the displacement vector. Because the displacement is horizontal and is measured relative to the horizontal, the component of tension parallel to the displacement is , not .
- Step 2Correct
You multiplied and isolated the trigonometric ratio correctly, but the equation carried forward the incorrect sine function from the first step.
- Step 3Correct
You evaluated the inverse trigonometric function accurately for your expression, but finding the angle requires rather than .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly substituted the numerical values for work, force, and displacement into the equation.
You calculated the product accurately.
You correctly isolated the trigonometric ratio and took the corresponding inverse trigonometric function.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou set up work using instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the parallel and perpendicular force components relative to displacement. Mechanical work requires the force component parallel to the direction of motion (), while represents the vertical component perpendicular to horizontal motion, which does zero work.
REASONING PATH
Your ACEpath teacher’s suggested approach- Direction of Parallel Component
Always draw a vector triangle showing the force and displacement. Identify the angle between them and use cosine for the adjacent (parallel) component.
- Perpendicular Forces Do No Work
Forces perpendicular to displacement satisfy , so .
Check whether your trigonometric component points along the displacement or perpendicular to it before setting up the equation.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the work equation with the parallel force component:
Substitute the given values:
Solve for the cosine of the angle:
Take the inverse cosine:
02 The student evaluates the inverse cosine with the calculator in radian mode but labels the resulting value with a degree symbol.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Your calculator was set to radian mode, yielding instead of degrees. Converting gives .
WHAT YOU DID WELL
Compliments from Your TeacherYou selected the correct work formula .
You correctly substituted the given values and simplified the ratio to find .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou computed the inverse cosine in radian mode and labeled the resulting numerical value with a degree symbol.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking the angle mode setting on the calculator when evaluating trigonometric or inverse trigonometric functions in physics problems that require degrees.
REASONING PATH
Your ACEpath teacher’s suggested approach- Check calculator angle mode
Before computing , , , or their inverses, check whether the display shows 'DEG' or 'RAD'.
Ensure the calculator mode matches the target unit of your problem before pressing the trig key.
- Perform a sanity check on geometric angles
An angle of is nearly imperceptible to the human eye, whereas .
Check that , confirming that was in radians.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet the calculator to Degree mode (DEG).
Evaluate .
Round to three significant figures to match the given data.
03 The student forgets to apply the inverse trigonometric function and mistakenly reports the value of cos(θ) itself as the angle in degrees.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You set the angle equal to the value of and simply attached the degree symbol, instead of taking the inverse cosine () to find the actual angle.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified and applied the work formula .
You algebraically isolated as .
You accurately substituted the numerical values and computed the ratio .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou assigned the unit of degrees directly to the dimensionless value of without taking the inverse cosine.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou conflated the trigonometric ratio with the angle itself, overlooking that solving for an angle contained within a trigonometric function requires applying the inverse function ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Trigonometric Ratio vs. Angle
The value of is a dimensionless ratio between and , whereas is an angle measured in degrees or radians.
Always apply (or ) to both sides of the equation when isolating the angle from .
CORRECTED PATH
ACEpath Teacher's DemonstrationStart from the evaluated ratio: .
Apply the inverse cosine function to both sides: .
Evaluate the angle in degrees: , which rounds to .
Lock it in
What is the general formula for the mechanical work done by a constant force over a straight displacement ?
, where is the angle between the force vector and the displacement vector.
Similar question
A worker pulls a crate across a horizontal floor through a distance of using a rope inclined at above the horizontal. If the tension in the rope is , how much mechanical work does the tension perform on the crate?
Answer
.
A lawnmower is pushed down and forward along a level lawn with a constant force of directed along the handle at an angle of below the horizontal. If the person does of work, what is the horizontal distance traveled by the lawnmower?
Answer
Rearrange to solve for distance: .
A box is pulled up a ramp inclined at above the horizontal. A rope pulls the box with a tension of at an angle of above the ramp's surface. If the box moves along the ramp, calculate the work done by the tension force.
Answer
The displacement is along the ramp surface, so the relevant angle between force and displacement is (not or ). Therefore, .