Resources

A uniform thin wooden rod of length L=1.20 mL = 1.20\text{ m} and mass M=0.600 kgM = 0.600\text{ kg} lies horizontally. A small lead weight of mass m=0.200 kgm = 0.200\text{ kg} is clamped to one end of the rod. Instead of the standard distance from the lead-weighted end, determine the ratio η=dleaddfree\eta = \frac{d_{\text{lead}}}{d_{\text{free}}}, where dleadd_{\text{lead}} is the distance from the center of mass of the combined assembly to the lead-weighted end, and dfreed_{\text{free}} is the distance from the center of mass to the opposite free end.

Answer and steps

Final answer

η=0.600\eta = 0.600

Steps

01

Establish the Coordinate System

Let the rod lie along the xx-axis from x=0x = 0 to x=Lx = L:

  • The lead weight of mass m=0.200 kgm = 0.200\text{ kg} is located at the weighted end, x=0x = 0.
  • Because the rod is uniform, its center of mass lies at its geometric midpoint: xrod=L2=1.20 m2=0.600 mx_{\text{rod}} = \frac{L}{2} = \frac{1.20\text{ m}}{2} = 0.600\text{ m} with rod mass M=0.600 kgM = 0.600\text{ kg}.
  • The free end of the rod is at x=L=1.20 mx = L = 1.20\text{ m}.

02

Locate the Center of Mass of the Assembly

The position of the center of mass of the combined system measured from the lead end (x=0x = 0) is: dlead=xcm=m⋅0+M⋅L2m+M=ML2(M+m)d_{\text{lead}} = x_{\text{cm}} = \frac{m \cdot 0 + M \cdot \frac{L}{2}}{m + M} = \frac{M L}{2(M + m)}

Substitute the numerical values: dlead=(0.600 kg)(0.600 m)0.200 kg+0.600 kg=0.360 kg⋅m0.800 kg=0.450 md_{\text{lead}} = \frac{(0.600\text{ kg})(0.600\text{ m})}{0.200\text{ kg} + 0.600\text{ kg}} = \frac{0.360\text{ kg}\cdot\text{m}}{0.800\text{ kg}} = 0.450\text{ m}


03

Find the Distance to the Free End

The distance from the center of mass to the opposite free end is: dfree=L−dlead=1.20 m−0.450 m=0.750 md_{\text{free}} = L - d_{\text{lead}} = 1.20\text{ m} - 0.450\text{ m} = 0.750\text{ m}


04

Calculate the Ratio η\eta

Divide dleadd_{\text{lead}} by dfreed_{\text{free}}: η=dleaddfree=0.450 m0.750 m=0.600\eta = \frac{d_{\text{lead}}}{d_{\text{free}}} = \frac{0.450\text{ m}}{0.750\text{ m}} = 0.600

(Alternative Check)
Using algebraic substitution directly gives: η=ML2(M+m)L−ML2(M+m)=MM+2m=0.6000.600+2(0.200)=0.6001.000=0.600\eta = \frac{\frac{ML}{2(M+m)}}{L - \frac{ML}{2(M+m)}} = \frac{M}{M + 2m} = \frac{0.600}{0.600 + 2(0.200)} = \frac{0.600}{1.000} = 0.600 which confirms the result is independent of the rod's length.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student treats the entire mass of the rod as concentrated at the far end L rather than at its midpoint L/2.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    xcm=m(0)+M(L)m+M  ⟹  xcm=0.200(0)+0.600(1.20)0.800  ⟹  xcm=0.900 mx_{\text{cm}} = \frac{m(0) + M(L)}{m + M} \implies x_{\text{cm}} = \frac{0.200(0) + 0.600(1.20)}{0.800} \implies x_{\text{cm}} = 0.900\text{ m}

    Correct

    xcm=m(0)+M(L2)m+M=0.200(0)+0.600(0.600)0.800=0.450 mx_{\text{cm}} = \frac{m(0) + M\left(\frac{L}{2}\right)}{m + M} = \frac{0.200(0) + 0.600(0.600)}{0.800} = 0.450\text{ m}

    A uniform rod has its individual center of mass at its midpoint x=L2=0.600 mx = \frac{L}{2} = 0.600\text{ m}, not at the opposite tip x=L=1.20 mx = L = 1.20\text{ m}.

  2. Step 2

    dlead=0.900 m  ⟹  dfree=1.20−0.900=0.300 md_{\text{lead}} = 0.900\text{ m} \implies d_{\text{free}} = 1.20 - 0.900 = 0.300\text{ m}

    Correct

    dlead=0.450 m  ⟹  dfree=1.20−0.450=0.750 md_{\text{lead}} = 0.450\text{ m} \implies d_{\text{free}} = 1.20 - 0.450 = 0.750\text{ m}

    Your relationship dfree=L−dleadd_{\text{free}} = L - d_{\text{lead}} is correct, but the numerical values are shifted due to the initial position error.

  3. Step 3

    η=0.9000.300=3\eta = \frac{0.900}{0.300} = 3

    Correct

    η=0.450 m0.750 m=0.600\eta = \frac{0.450\text{ m}}{0.750\text{ m}} = 0.600

    You computed the ratio correctly according to its definition, but the value reflects the earlier coordinate mistake.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the center-of-mass weighting formula ∑mixi∑mi\frac{\sum m_i x_i}{\sum m_i}.

You correctly placed the origin at the lead mass with coordinate x=0x = 0.

You correctly related the two segment lengths using dfree=L−dleadd_{\text{free}} = L - d_{\text{lead}} and evaluated the target ratio η=dleaddfree\eta = \frac{d_{\text{lead}}}{d_{\text{free}}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Misplaced distributed mass location

No, this is a conceptual misunderstanding regarding how a continuous uniform body is represented as an equivalent point mass.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the distributed mass of the uniform rod as if it were an end-point mass located at x=Lx = L, rather than replacing the uniform rod with an equivalent concentrated mass at its geometric center x=L2x = \frac{L}{2}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Continuous Uniform Objects
  • For a uniform extended body, the gravitational force and mass distribution act through its geometric center of mass.

  • Always identify the center of mass of each continuous sub-component before substituting it into a multi-body discrete formula.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Locate the rod's center of mass at xrod=L2=0.600 mx_{\text{rod}} = \frac{L}{2} = 0.600\text{ m}.

  2. Calculate dlead=xcm=0.200(0)+0.600(0.600)0.200+0.600=0.3600.800=0.450 md_{\text{lead}} = x_{\text{cm}} = \frac{0.200(0) + 0.600(0.600)}{0.200 + 0.600} = \frac{0.360}{0.800} = 0.450\text{ m}.

  3. Find the distance to the free end: dfree=1.20 m−0.450 m=0.750 md_{\text{free}} = 1.20\text{ m} - 0.450\text{ m} = 0.750\text{ m}.

  4. Compute the ratio: η=0.450 m0.750 m=0.600\eta = \frac{0.450\text{ m}}{0.750\text{ m}} = 0.600.

Final answer

η=0.600\eta = 0.600

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch extended objects and mark their individual centers of mass with a distinct symbol before writing coordinate equations.

  • Practice distinguishing point masses attached at boundaries from the center of mass of the supporting continuous body.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the requested ratio and calculates d_free / d_lead instead of d_lead / d_free.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    xrod=L2=1.202=0.60 mx_{\text{rod}} = \frac{L}{2} = \frac{1.20}{2} = 0.60\text{ m}

  2. Step 2

    dlead=0.200(0)+0.600(0.60)0.200+0.600=0.450 md_{\text{lead}} = \frac{0.200(0) + 0.600(0.60)}{0.200 + 0.600} = 0.450\text{ m}

  3. Step 3

    dfree=1.20−0.450=0.750 md_{\text{free}} = 1.20 - 0.450 = 0.750\text{ m}

  4. Step 4

    η=dfreedlead  ⟹  η=0.7500.450=53=1.67\eta = \frac{d_{\text{free}}}{d_{\text{lead}}} \implies \eta = \frac{0.750}{0.450} = \frac{5}{3} = 1.67

    Correct

    η=dleaddfree=0.450 m0.750 m=0.600\eta = \frac{d_{\text{lead}}}{d_{\text{free}}} = \frac{0.450\text{ m}}{0.750\text{ m}} = 0.600

    The problem asks for η=dleaddfree\eta = \frac{d_{\text{lead}}}{d_{\text{free}}}, but you placed dfreed_{\text{free}} in the numerator and dleadd_{\text{lead}} in the denominator, resulting in the reciprocal of the correct ratio.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the center of mass of the uniform rod at half its total length.

You properly set up and computed the weighted average to locate the system's center of mass relative to the clamped weight.

You accurately found the complementary distance from the center of mass to the rod's opposite free end.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted target ratio definition

You accidentally placed the larger segment in the numerator, calculating dfree/dleadd_{\text{free}} / d_{\text{lead}} rather than following the prompt's defined ratio dlead/dfreed_{\text{lead}} / d_{\text{free}}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Misreading the target quotient order: when finding an unfamiliar ratio η=A/B\eta = A/B, it is easy to default intuitively to larger-over-smaller or reverse the numerator and denominator during transcription.

REASONING PATH
Your ACEpath teacher’s suggested approach
Verify Target Variable Definitions
  • Always underline or transcribe the exact given formula before substituting numbers: η=NumeratorDenominator\eta = \frac{\text{Numerator}}{\text{Denominator}}.

  • Check that the variable defined as dleadd_{\text{lead}} sits on top and dfreed_{\text{free}} sits on the bottom before carrying out the division.

Physical Reality Check on Center of Mass
  • Adding mass to one end shifts the center of mass closer to that end, making dlead<dfreed_{\text{lead}} < d_{\text{free}}, so dleaddfree<1\frac{d_{\text{lead}}}{d_{\text{free}}} < 1.

  • Since dlead<dfreed_{\text{lead}} < d_{\text{free}}, verify that your final ratio η\eta is strictly less than 11.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the prompt's exact target ratio: η=dleaddfree\eta = \frac{d_{\text{lead}}}{d_{\text{free}}}.

  2. Substitute your verified segment lengths: dlead=0.450 md_{\text{lead}} = 0.450\text{ m} and dfree=0.750 md_{\text{free}} = 0.750\text{ m}.

  3. Compute the decimal quotient: η=0.4500.750=35=0.600\eta = \frac{0.450}{0.750} = \frac{3}{5} = 0.600.

Final answer

η=0.600\eta = 0.600

NEXT STEPS
Final Takeaways from Your Teacher
  • Before substituting numbers, explicitly circle the defined ratio formula in the problem text.

  • Perform a physical bounds check: because the center of mass lies closer to the heavier end, dlead<dfreed_{\text{lead}} < d_{\text{free}}, meaning the ratio dleaddfree\frac{d_{\text{lead}}}{d_{\text{free}}} must be less than 11.

OverviewACEpath Teacher's Diagnosis

03 The student neglects the mass of the added lead weight in the denominator of the center-of-mass formula.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    xcm=M(L/2)M  ⟹  xcm=0.600×0.600.600=0.60 mx_{\text{cm}} = \frac{M(L/2)}{M} \implies x_{\text{cm}} = \frac{0.600 \times 0.60}{0.600} = 0.60\text{ m}

    Correct

    xcm=m⋅0+M(L/2)m+M=0.600×0.6000.200+0.600=0.450 mx_{\text{cm}} = \frac{m \cdot 0 + M(L/2)}{m + M} = \frac{0.600 \times 0.600}{0.200 + 0.600} = 0.450\text{ m}

    In the center-of-mass definition xcm=∑mixi∑mix_{\text{cm}} = \frac{\sum m_i x_i}{\sum m_i}, the denominator must be the total mass of the combined assembly, mtotal=m+M=0.200 kg+0.600 kg=0.800 kgm_{\text{total}} = m + M = 0.200\text{ kg} + 0.600\text{ kg} = 0.800\text{ kg}. Dividing only by the rod's mass MM ignores the inertia of the lead clamp and leaves the center of mass unshifted at the rod's midpoint.

  2. Step 2

    dlead=0.60 m  ⟹  dfree=1.20−0.60=0.60 md_{\text{lead}} = 0.60\text{ m} \implies d_{\text{free}} = 1.20 - 0.60 = 0.60\text{ m}

    Correct

    dlead=0.450 m  ⟹  dfree=1.20 m−0.450 m=0.750 md_{\text{lead}} = 0.450\text{ m} \implies d_{\text{free}} = 1.20\text{ m} - 0.450\text{ m} = 0.750\text{ m}

    Your subtraction method dfree=L−dleadd_{\text{free}} = L - d_{\text{lead}} is conceptually sound, but the numerical values carry over the incorrect xcmx_{\text{cm}} from Step 1.

  3. Step 3

    η=0.600.60=1\eta = \frac{0.60}{0.60} = 1

    Correct

    η=dleaddfree=0.450 m0.750 m=0.600\eta = \frac{d_{\text{lead}}}{d_{\text{free}}} = \frac{0.450\text{ m}}{0.750\text{ m}} = 0.600

    You correctly evaluated the quotient dleaddfree\frac{d_{\text{lead}}}{d_{\text{free}}}, but the result η=1\eta = 1 is incorrect because it was computed using the unshifted distances.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly located the geometric center of mass of the uniform rod at L/2=0.60 mL/2 = 0.60\text{ m}.

You used the correct geometric relation dfree=L−dleadd_{\text{free}} = L - d_{\text{lead}}.

You set up the final target ratio η=dleaddfree\eta = \frac{d_{\text{lead}}}{d_{\text{free}}} accurately according to the problem statement.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted added mass in total system mass

You divided by only the rod's mass MM rather than the sum of all masses (M+m)(M + m) in the system.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the mass of an individual component with the total mass of the system in the center-of-mass formula xcm=∑mixiMtotalx_{\text{cm}} = \frac{\sum m_i x_i}{M_{\text{total}}}, leading to an unshifted balance point.

REASONING PATH
Your ACEpath teacher’s suggested approach
Total Mass in the Denominator
  • Mtotal=∑mi=m1+m2+⋯+mnM_{\text{total}} = \sum m_i = m_1 + m_2 + \dots + m_n

  • Always list and sum the masses of all objects in the system before evaluating xcmx_{\text{cm}}.

Physical Reasonableness Check
  • Adding mass to one end of a symmetrical body must shift the center of mass toward that end.

  • Check that dlead<L/2d_{\text{lead}} < L/2 and consequently η<1\eta < 1 whenever an extra mass is clamped at x=0x = 0.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the total mass of the assembly: Mtotal=m+M=0.200 kg+0.600 kg=0.800 kgM_{\text{total}} = m + M = 0.200\text{ kg} + 0.600\text{ kg} = 0.800\text{ kg}.

  2. Calculate the center of mass position measured from the lead end: dlead=xcm=m(0)+M(L/2)m+M=0.600 kg×0.600 m0.800 kg=0.450 md_{\text{lead}} = x_{\text{cm}} = \frac{m(0) + M(L/2)}{m + M} = \frac{0.600\text{ kg} \times 0.600\text{ m}}{0.800\text{ kg}} = 0.450\text{ m}.

  3. Determine the distance to the opposite free end: dfree=L−dlead=1.20 m−0.450 m=0.750 md_{\text{free}} = L - d_{\text{lead}} = 1.20\text{ m} - 0.450\text{ m} = 0.750\text{ m}.

  4. Calculate the ratio: η=dleaddfree=0.4500.750=0.600\eta = \frac{d_{\text{lead}}}{d_{\text{free}}} = \frac{0.450}{0.750} = 0.600.

Final answer

η=0.600\eta = 0.600

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the definition of center of mass for multi-body systems, ensuring MtotalM_{\text{total}} includes every particle or body.

  • Perform qualitative checks before calculating: verify whether adding mass should shift the center of mass left, right, or keep it stationary.

  • Practice computing distance ratios from the center of mass to both ends of weighted rods.

Lock it in

Similar question

01

A uniform rod of mass M=0.40 kgM = 0.40\text{ kg} and length L=1.0 mL = 1.0\text{ m} has a small point mass m=0.10 kgm = 0.10\text{ kg} attached at one end. What is the distance of the system's center of mass from the weighted end?

Answer

d=0.40 md = 0.40\text{ m}. Set origin at the point mass: xcm=m(0)+M(L/2)m+M=0.10(0)+0.40(0.50)0.10+0.40=0.200.50=0.40 mx_{\text{cm}} = \frac{m(0) + M(L/2)}{m + M} = \frac{0.10(0) + 0.40(0.50)}{0.10 + 0.40} = \frac{0.20}{0.50} = 0.40\text{ m}.

02

A uniform meter stick (L=100 cmL = 100\text{ cm}, mass M=150 gM = 150\text{ g}) has a 50 g50\text{ g} mass attached at the 0 cm0\text{ cm} mark and a 100 g100\text{ g} mass attached at the 100 cm100\text{ cm} mark. Find the position of the center of mass along the stick.

Answer

xcm=58.3 cmx_{\text{cm}} = 58.3\text{ cm}. Calculate moments: xcm=50(0)+150(50)+100(100)50+150+100=0+7500+10000300=17500300≈58.33 cmx_{\text{cm}} = \frac{50(0) + 150(50) + 100(100)}{50 + 150 + 100} = \frac{0 + 7500 + 10000}{300} = \frac{17500}{300} \approx 58.33\text{ cm}.

03

A uniform rod of mass MM and length LL has a lead weight of mass m=M3m = \frac{M}{3} attached at one end. Determine the ratio η=dweighteddfree\eta = \frac{d_{\text{weighted}}}{d_{\text{free}}} of the distances from the center of mass to the two ends.

Answer

η=0.60\eta = 0.60 (or 35\frac{3}{5}). From the weighted end, dweighted=M(L/2)M+M/3=ML/24M/3=38Ld_{\text{weighted}} = \frac{M(L/2)}{M + M/3} = \frac{M L / 2}{4M / 3} = \frac{3}{8}L. Then dfree=L−38L=58Ld_{\text{free}} = L - \frac{3}{8}L = \frac{5}{8}L. Thus η=3/85/8=35=0.60\eta = \frac{3/8}{5/8} = \frac{3}{5} = 0.60.

Loading workspace…