Resources
A robotic block of mass rests on a flat horizontal platform. The static coefficient of friction is . The kinetic coefficient of friction varies as a function of the surface lubrication layer according to , where is a non-dimensional wear index. The block is subjected to a slowly increasing horizontal pulling force until it initiates motion at . Evaluate: (a) the magnitude of the initial acceleration of the block at the exact instant slip commences in the unlubricated limit , and (b) the limiting acceleration as (the idealized smooth-transition limit where ). Take .
Answer and steps
Final answer
(a) As , ; (b) As , .
Steps
Unlubricated Limit ()
Identify the Normal Force and the Impending Slip Condition
The block of mass rests on a level horizontal surface, so the normal force balances gravity vertically: The pulling force increases slowly until it reaches the maximum static friction force , at which point the block begins to slip: Numerically:
Formulate the Equation of Motion at the Instant Motion Begins
The instant slip occurs, the resistive force abruptly transitions from static friction to kinetic friction : According to Newton's second law, the initial horizontal net force determines the immediate acceleration : Dividing by the mass : Substituting the given dependence :
Common Pitfall: A common error is assuming that the pulling force drops or adjusts smoothly to match kinetic friction. Since the force was raised to to initiate motion, the instantaneous applied force remains equal to at the exact moment of slip. Any difference between and results in an instantaneous non-zero acceleration (often referred to as stick-slip behavior).
Evaluate the Limits
As , the exponential term decays to zero:
Thus, the coefficient of kinetic friction becomes:
The initial acceleration is:
Idealized Smooth-Transition Limit ()
As :
Here, , meaning there is no discontinuity between the static threshold and the kinetic friction force. Therefore:
Typical errors
01 The student forgets that once motion begins kinetic friction opposes motion rather than static friction, resulting in zero net force and zero acceleration.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
The instant sliding motion begins, the contact friction abruptly drops from maximum static friction to kinetic friction . For , , so the resistive force drops to , leaving an unbalanced net force of .
- Step 3
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the normal force and calculated the maximum static friction force needed to overcome stick.
You correctly evaluated the limit as where kinetic friction matches static friction.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou used instead of to find the net force once sliding commenced in part (a).
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing impending motion with actual sliding: static friction applies strictly while surfaces are stationary relative to each other. The instant relative motion initiates, the contact force transitions to kinetic friction, which is typically smaller than maximum static friction.
REASONING PATH
Your ACEpath teacher’s suggested approach- Friction Regime Transition
before slip; as soon as relative motion begins.
Always switch the opposing frictional force in Newton's second law from to the moment relative motion starts.
CORRECTED PATH
ACEpath Teacher's DemonstrationEvaluate in the limit : .
Calculate the kinetic friction force: .
Apply Newton's second law at the slip instant: .
Solve for the initial acceleration: .
(a) ; (b)
02 The student miscalculates the limit of e^(-ε) as ε → ∞ as 1 instead of 0, giving μk = μs and thus zero acceleration.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
For positive exponential decay, , not . This gives rather than .
- Step 3Correct
Your application of Newton's second law was algebraically consistent with your earlier value, but it was affected by the incorrect value of .
- Step 4
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that slip begins when the applied horizontal force reaches .
You set up Newton's second law properly using .
You correctly evaluated the limit to find the acceleration for part (b).
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted for as instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the behavior of exponential decay at infinity () with its behavior at zero ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Decaying Exponential Limits
For a decaying exponential with : , whereas .
Always write as when taking limits to positive infinity to make the division by an increasingly large number obvious.
CORRECTED PATH
ACEpath Teacher's DemonstrationAs , the term .
Compute .
Find the kinetic friction force: .
Apply Newton's second law: .
(a) ; (b)
03 The student calculates the acceleration using the total applied force rather than the net force, omitting kinetic friction from Newton's second law.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Once the block begins to slip, kinetic friction opposes the motion. Newton's second law requires using the net force , not just the applied force .
- Step 3
(omitted)
Correct(a) As , ; (b) As ,
You did not evaluate the two specific wear index limits and specified in parts (a) and (b).
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that slip initiates when the pulling force reaches the maximum static friction threshold .
You accurately computed the numerical value of the applied force as .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou divided the single applied pulling force by mass instead of subtracting kinetic friction to find the net horizontal force.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating impending slip with frictionless motion: when static friction is overcome, friction does not drop to zero; it transitions to kinetic friction , which continues to oppose motion in Newton's second law.
REASONING PATH
Your ACEpath teacher’s suggested approach- Net Force Upon Motion
once relative sliding begins.
Always draw a free-body diagram showing the kinetic friction vector pointing opposite to the instantaneous relative velocity.
- Parametric Limits
Check edge cases: as , ; as , .
Substitute the limiting values into the difference before calculating numerical accelerations.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite Newton's second law for the instant slip starts: .
Substitute and to get .
Use the given relation , which gives .
Evaluate part (a) as : .
Evaluate part (b) as : .
(a) ; (b)
Lock it in
What force opposes motion at the exact instant relative sliding between two surfaces begins?
Kinetic friction . Once relative motion begins, static friction ceases to act.
Similar question
A block of mass rests on a horizontal floor with and . A horizontal pulling force is slowly increased until the block begins to move. Calculate the acceleration of the block immediately after it starts slipping. (Take .)
Answer
.
A crate rests on a horizontal surface where . A horizontal pulling force is applied, which is just enough to initiate motion (). If the crate is observed to accelerate at immediately upon slipping, determine the coefficient of kinetic friction .
Answer
Using , we have .
A block of mass sits on a platform inclined at angle . The coefficients of friction are and . A force directed up the incline is gradually increased from zero until the block begins to slip upward. Find the magnitude of the block's acceleration immediately after slip begins. (Take .)
Answer
At impending upward slip, . Immediately after slip begins, kinetic friction opposes upward motion: . The net force along the incline is . Thus .