Resources
A linear inspection drone starts from rest at and accelerates uniformly at until it reaches a speed of . It immediately begins braking uniformly at a constant rate of until it comes to a complete halt. If the total distance traveled from launch to stop must not exceed , determine the minimum magnitude of deceleration, , required.
Answer and steps
Final answer
Steps
Calculate the distance covered during acceleration ()
Method 1: Using Kinematic Equations
The motion consists of two distinct phases: uniform acceleration followed by uniform braking.
The drone accelerates from rest () to a peak speed of with acceleration .
Using the kinematic relation :
Determine the maximum allowable braking distance ()
The total distance must not exceed :
To minimize the magnitude of deceleration , the braking distance must be maximized:
Calculate the minimum deceleration magnitude ()
During the braking phase, the drone decelerates from to a stop ():
Alternative Method: Speed-Time (-) Graph
On a speed-time graph, the motion forms a triangle with a peak height of :
- Acceleration time ():
- Total area under the graph: The total area represents the total displacement:
- Minimum deceleration: A longer braking time yields a smaller deceleration:
Common Pitfall: Forgetting that minimizing deceleration corresponds to maximizing distance or time. Braking harder (higher deceleration) would stop the drone in less distance, which also satisfies , but the question asks specifically for the minimum deceleration required.
Typical errors
01 A student omits the factor of 2 in the kinematic formula v² = 2ad, calculating distances as v²/a.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You omitted the factor of in the denominator of the kinematic relation . When starting from rest, the distance is , which gives rather than .
- Step 2Correct
Your subtraction logic is sound, but the value is affected by your earlier error in .
- Step 3Correct
You repeated the missing-factor error by setting instead of , and you also evaluated it using the affected value .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that the drone's motion consists of two distinct constant-acceleration stages.
You correctly identified that the maximum allowable braking distance is the total distance minus the acceleration distance.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of , leaving out the factor of that arises from integrating constant acceleration or finding the triangular area on a velocity-time graph.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating dimensional relations or forgetting the coefficient in the third kinematic equation (), leading to systematic overestimation of stopping and acceleration distances.
REASONING PATH
Your ACEpath teacher’s suggested approach- Kinematic Formula Check
For motion with constant acceleration , the relationship between speed and displacement is .
Always write the full formula before isolating distance as .
- Geometric Sanity Check via $v$-$t$ Graph
Displacement under uniform acceleration equals average velocity times time: .
Verify that your distance matches the triangular area on a velocity-time plot.
CORRECTED PATH
ACEpath Teacher's Demonstration02 A student applies the total distance limit to the braking phase alone without subtracting the distance covered during acceleration.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You assigned the total flight distance constraint () directly to the braking phase alone, omitting the already covered during acceleration.
- Step 3Correct
Your kinematic formula setup and algebraic rearrangement were correct, but the numerical result was affected by the incorrect braking distance from Step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou selected the correct kinematic relation for both phases.
You accurately computed the distance traveled during the acceleration stage.
You recognized that the minimum deceleration corresponds to using the maximum allowable stopping distance.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the total allowable displacement as the braking displacement, overlooking that displacement accumulated in the first phase reduces the remaining distance available for stopping.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisIn multi-phase motion with an overall distance constraint , the available distance for subsequent phases is constrained by the sum: . Forgetting to partition the total budget across all phases leads to overestimating the distance available for later stages.
REASONING PATH
Your ACEpath teacher’s suggested approach- Displacement partitioning
For sequential one-dimensional motion in a single direction, the total displacement is the sum of displacements of each phase: .
Always write down the total displacement budget equation before solving for an individual phase distance.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the total distance budget: .
Subtract the acceleration distance: .
Calculate the minimum braking deceleration using : .
03 A student forgets to square the velocity when applying the kinematic relation, using v instead of v² in the formula for stopping distance.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You correctly identified the relationship between initial speed, acceleration, and distance, but you forgot to square the velocity . From , the distance is .
- Step 2Correct
Your logic of subtracting the acceleration distance from the total allowable distance is sound, but this step uses the incorrect value of from Step 1.
- Step 3Correct
You repeated the formula mistake by using instead of . From , the deceleration magnitude is .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly partitioned the motion into an accelerating phase and a braking phase.
You recognized that the braking distance is the total allowable distance minus the acceleration distance.
You correctly related acceleration, stopping distance, and speed into an algebraic ratio.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeNo, this is a conceptual misunderstanding of the kinematic formula dimensions rather than a single arithmetic slip, as you omitted the square of velocity in both phases.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou recalled the kinematic equation relating velocity, acceleration, and displacement as linear in velocity () rather than quadratic (). Dimensional analysis confirms that , which balances .
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional Consistency Check
Always verify units: matches , whereas does not match .
Before calculating, write the standard formula and check that velocity carries an exponent of 2.
- Speed-Time Graph Area Check
On a - graph, distance is the area of a triangle: .
Sketch a quick - triangle to visually verify that distance must scale with .
CORRECTED PATH
ACEpath Teacher's DemonstrationLock it in
What is the correct relationship linking initial velocity , final velocity , constant acceleration , and displacement ?
, which rearranges from rest () to . Remember the coefficient 2 comes from average velocity .
Similar question
A subway train accelerates uniformly from rest at to a cruising speed of . Find the distance traveled during this acceleration phase.
Answer
. Using , we have .
An electric scooter accelerates from rest at to , cruises at for , and then brakes to rest at . What is the total distance traveled?
Answer
. Acceleration distance: . Cruise distance: . Braking distance: . Total distance: .
A delivery pod travels between two stations apart. It accelerates from rest at up to a maximum speed , and immediately decelerates at a constant magnitude to come to a halt at the destination. Calculate .
Answer
(or ). Total distance is . Thus .