Resources

A cylindrical ohmic heating element is connected across an ideal DC power supply maintaining a steady terminal voltage of V=120 VV = 120\text{ V}. An ammeter placed in series with the element registers a steady current of I=4.80 AI = 4.80\text{ A}. (a) Calculate the electrical resistance RR of the heating element. (b) Determine the total quantity of electric charge QQ in coulombs that passes through any cross-section of the element in Δt=2.50 min\Delta t = 2.50\text{ min}. (c) In one or two concise sentences, distinguish physically between current, voltage, and resistance in this circuit context.

Answer and steps

Final answer

(a) R=25.0 ΩR = 25.0\ \Omega; (b) Q=7.20×102 CQ = 7.20 \times 10^2\text{ C}; (c) Voltage (120 V120\text{ V}) is the electric potential energy difference per unit charge driving the flow; current (4.80 A4.80\text{ A}) is the time rate at which electric charge traverses a cross-section; resistance (25.0 Ω25.0\ \Omega) is the intrinsic geometric and material opposition to that charge flow.

Steps

Part (a): Determining Electrical Resistance

According to Ohm's law, for an ohmic conductor, the potential difference (voltage) VV across the conductor is directly proportional to the electric current II flowing through it:

V=IRV = I R

Rearranging the formula to solve for the resistance RR:

R=VIR = \frac{V}{I}

Substitute the given values (V=120 VV = 120\text{ V} and I=4.80 AI = 4.80\text{ A}):

R=120 V4.80 A=25.0 ΩR = \frac{120\text{ V}}{4.80\text{ A}} = 25.0\ \Omega


Part (b): Calculating the Total Charge Flow

Electric current II is defined as the rate at which electric charge ΔQ\Delta Q passes through a given cross-sectional area per unit time Δt\Delta t:

I=ΔQΔtI = \frac{\Delta Q}{\Delta t}

Rearranging to solve for the total charge QQ:

Q=I⋅ΔtQ = I \cdot \Delta t

First, convert the elapsed time from minutes to standard SI units (seconds):

Δt=2.50 min⋅60 s/min=150 s\Delta t = 2.50\text{ min} \cdot 60\text{ s/min} = 150\text{ s}

Now calculate QQ:

Q=(4.80 A)(150 s)=720 C=7.20×102 CQ = (4.80\text{ A})(150\text{ s}) = 720\text{ C} = 7.20 \times 10^2\text{ C}

Common Pitfall: Always ensure time is converted to seconds (s\text{s}) before multiplying by amperes (A=C/s\text{A} = \text{C/s}), as using minutes directly yields an incorrect unit (A⋅min\text{A}\cdot\text{min}).


Part (c): Physical Distinction Between Current, Voltage, and Resistance

  • Voltage (120 V120\text{ V}): The electric potential difference (energy per unit charge, 1 V=1 J/C1\text{ V} = 1\text{ J/C}) supplied across the element that creates an electric field and drives the charges to move.
  • Current (4.80 A4.80\text{ A}): The actual rate of electric charge flow past any cross-section of the element per unit time (1 A=1 C/s1\text{ A} = 1\text{ C/s}).
  • Resistance (25.0 Ω25.0\ \Omega): The opposition offered by the material's internal structure and geometry to the flow of charge, determining how much current results from a given applied voltage.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert the time interval from minutes to seconds, resulting in a charge of 12.0 C instead of 720 C.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R=VI  ⟹  R=1204.80=25.0 ΩR = \frac{V}{I} \implies R = \frac{120}{4.80} = 25.0\ \Omega

  2. Step 2

    Q=IΔt  ⟹  Q=4.80×2.50  ⟹  Q=12.0 CQ = I \Delta t \implies Q = 4.80 \times 2.50 \implies Q = 12.0\text{ C}

    Correct

    Δt=2.50 min×60 s/min=150 s  ⟹  Q=IΔt=(4.80 A)(150 s)=720 C\Delta t = 2.50\text{ min} \times 60\text{ s/min} = 150\text{ s} \implies Q = I \Delta t = (4.80\text{ A})(150\text{ s}) = 720\text{ C}

    You used the time in minutes (2.50 min2.50\text{ min}) directly instead of converting it to seconds (150 s150\text{ s}). Because an ampere is a coulomb per second (1 A=1 C/s1\text{ A} = 1\text{ C/s}), time must be in seconds to yield charge in coulombs.

  3. Step 3

    "Voltage is the potential difference that pushes charges through the element. Current is the rate at which charge flows, and resistance is the opposition of the element to that flow."

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly stated and solved Ohm's law for resistance in part (a).

You identified the correct fundamental relation between current, charge, and time, Q=IΔtQ = I \Delta t.

You accurately explained the physical roles of voltage, current, and resistance in part (c).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Omission (Minutes to Seconds)

You multiplied the current by elapsed time expressed in minutes instead of converting to seconds.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating given numerical values as pure numbers rather than physical quantities with specific units, overlooking that the SI derived unit of current is defined as coulombs per second (A=C/s\text{A} = \text{C/s}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Inspect Derived SI Units
  • 1 A=1 C/s1\text{ A} = 1\text{ C/s}, so charge in coulombs requires time in seconds ([C]=[A]⋅[s][\text{C}] = [\text{A}] \cdot [\text{s}]).

  • Always convert time from minutes or hours into seconds before computing charge with Q=IΔtQ = I \Delta t.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the elapsed time to seconds: Δt=2.50 min×60 s/min=150 s\Delta t = 2.50\text{ min} \times 60\text{ s/min} = 150\text{ s}.

  2. Multiply current by time in seconds: Q=(4.80 A)(150 s)=720 CQ = (4.80\text{ A})(150\text{ s}) = 720\text{ C}.

Final answer

(a) R=25.0 ΩR = 25.0\ \Omega; (b) Q=720 CQ = 720\text{ C} (or 7.20×102 C7.20 \times 10^2\text{ C}); (c) Voltage is the potential difference driving charges, current is the rate of charge flow, and resistance is the opposition to charge flow.

NEXT STEPS
Final Takeaways from Your Teacher
  • Write down explicit units beside every number inside your substitution step (e.g., 4.80 A×150 s4.80\text{ A} \times 150\text{ s}).

  • Verify that time units cancel properly: (C/s)×s=C(\text{C/s}) \times \text{s} = \text{C}.

OverviewACEpath Teacher's Diagnosis

02 The student inverts Ohm's law as R = I / V, calculating an incorrect resistance of 0.0400 Ω.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R=IV  ⟹  R=4.80120  ⟹  R=0.0400 ΩR = \frac{I}{V} \implies R = \frac{4.80}{120} \implies R = 0.0400\ \Omega

    Correct

    R=VI=120 V4.80 A=25.0 ΩR = \frac{V}{I} = \frac{120\text{ V}}{4.80\text{ A}} = 25.0\ \Omega

    You inverted Ohm's law (V=IRV = I R). Dividing both sides by II gives R=VIR = \frac{V}{I}, which evaluates to 25.0 Ω25.0\ \Omega. The ratio IV\frac{I}{V} calculates electrical conductance (GG), not resistance.

  2. Step 2

    Δt=2.50×60=150 s  ⟹  Q=IΔt=4.80×150=720 C\Delta t = 2.50 \times 60 = 150\text{ s} \implies Q = I\Delta t = 4.80 \times 150 = 720\text{ C}

  3. Step 3

    Voltage is the electric push provided by the supply across the element. Current is the flow rate of charge, while resistance measures how much the element resists the current.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted minutes to seconds before computing charge.

You applied the relationship between electric current and charge Q=IΔtQ = I \Delta t flawlessly.

You clearly articulated the intuitive physical meanings of voltage, current, and resistance.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Ohm's Law Formula

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You recalled or rearranged Ohm's law with II in the numerator rather than isolating RR from the fundamental definition V=IRV = IR, confusing resistance R=VIR = \frac{V}{I} with electrical conductance G=IVG = \frac{I}{V}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Fundamental Form of Ohm's Law
  • Ohm's law relates potential difference, current, and resistance as V=IRV = I R.

  • Start from V=IRV = I R and divide both sides by current II to obtain R=VIR = \frac{V}{I}.

Unit and Dimensional Sanity Check
  • 1 Ω=1 V/A1\ \Omega = 1\text{ V}/\text{A}.

  • Verify that your fraction has volts on top and amperes on the bottom so the units evaluate to ohms.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State Ohm's law: V=IRV = I R.

  2. Isolate resistance RR: R=VIR = \frac{V}{I}.

  3. Substitute V=120 VV = 120\text{ V} and I=4.80 AI = 4.80\text{ A}: R=120 V4.80 A=25.0 ΩR = \frac{120\text{ V}}{4.80\text{ A}} = 25.0\ \Omega.

Final answer

(a) R=25.0 ΩR = 25.0\ \Omega; (b) Q=7.20×102 CQ = 7.20 \times 10^2\text{ C}; (c) Voltage drives the flow, current is the rate of flow, and resistance opposes the flow.

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out the base equation V=IRV = IR before rearranging variables to prevent inversion errors.

  • Perform a quick unit check (1 Ω=1 V/A1\ \Omega = 1\text{ V}/\text{A}) whenever solving for resistance.

OverviewACEpath Teacher's Diagnosis

03 The student confuses electric current with the total charge itself, defining current as the amount of charge stored or moved rather than the rate of flow.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R=VI  ⟹  R=1204.80=25.0 ΩR = \frac{V}{I} \implies R = \frac{120}{4.80} = 25.0\ \Omega

  2. Step 2

    Δt=2.50×60=150 s  ⟹  Q=IΔt  ⟹  Q=4.80×150=720 C\Delta t = 2.50 \times 60 = 150\text{ s} \implies Q = I \Delta t \implies Q = 4.80 \times 150 = 720\text{ C}

  3. Step 3

    Voltage is the energy per charge pushing electrons through the wire, while resistance is the opposition to charge movement. Current is the total amount of electric charge moving through the heating element.

    Correct

    Voltage is the electric potential energy difference per unit charge driving flow; resistance is the material and geometric opposition to flow; current is the rate of charge flow per unit time (I=ΔQΔtI = \frac{\Delta Q}{\Delta t}).

    You correctly identified voltage as energy per charge and resistance as opposition to flow, but you described current as a total quantity of charge (QQ) instead of a time rate of flow (charge per unit time, C/s\text{C/s}).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly stated and evaluated Ohm's law to find the heating element's resistance.

You converted the time from minutes to seconds before calculating the total charge.

You accurately defined voltage as energy per unit charge and resistance as opposition to charge motion.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Quantity vs. Rate Confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated electric current as an absolute quantity of charge rather than a time rate of transfer (1 A=1 C/s1\text{ A} = 1\text{ C/s}). Current measures how rapidly charge passes through a cross-section, not the cumulative amount of charge that has passed.

REASONING PATH
Your ACEpath teacher’s suggested approach
Distinguish Charge from Current
  • Charge (QQ) is measured in coulombs (C\text{C}) and represents a physical quantity of charges. Current (I=ΔQΔtI = \frac{\Delta Q}{\Delta t}) is measured in amperes (1 A=1 C/s1\text{ A} = 1\text{ C/s}) and represents the rate at which charge passes a boundary.

  • Whenever you describe current in words, always include the rate or per-unit-time aspect (e.g., 'charge passing per second') rather than simply 'amount of charge'.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify that the total amount of charge is QQ, measured in coulombs (C\text{C}).

  2. Incorporate the time dependence from the definition I=ΔQΔtI = \frac{\Delta Q}{\Delta t}.

  3. State current as the time rate of charge flow: 4.80 A4.80\text{ A} means 4.80 coulombs4.80\text{ coulombs} pass through any cross-section of the element every second.

Final answer

Voltage (120 V120\text{ V}) is the electric potential energy difference per unit charge driving the flow; current (4.80 A4.80\text{ A}) is the time rate at which electric charge traverses a cross-section (4.80 C/s4.80\text{ C/s}); resistance (25.0 Ω25.0\ \Omega) is the intrinsic geometric and material opposition to that flow.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the definition of an ampere as one coulomb per second to reinforce that current is an instantaneous flow rate.

  • Practice using fluid flow analogies (volume vs. flow rate) to cement the difference between total quantity and rate.

Lock it in

Similar question

01

A steady current of 3.50 A3.50\text{ A} flows through a light bulb connected to a 14.0 V14.0\text{ V} battery. Determine (a) the resistance of the filament and (b) the total charge that passes through the bulb in 4.00 min4.00\text{ min}.

Answer

(a) R=VI=14.0 V3.50 A=4.00 ΩR = \frac{V}{I} = \frac{14.0\text{ V}}{3.50\text{ A}} = 4.00\ \Omega. (b) Convert time: Δt=4.00 min×60 s/min=240 s\Delta t = 4.00\text{ min} \times 60\text{ s/min} = 240\text{ s}. Charge: Q=IΔt=(3.50 A)(240 s)=840 CQ = I \Delta t = (3.50\text{ A})(240\text{ s}) = 840\text{ C}.

02

An electric kettle element has a resistance of 15.0 Ω15.0\ \Omega and draws current from a 240 V240\text{ V} outlet. Calculate how many coulombs of electric charge flow through the heating element while boiling water for 1.50 min1.50\text{ min}.

Answer

Current: I=VR=240 V15.0 Ω=16.0 AI = \frac{V}{R} = \frac{240\text{ V}}{15.0\ \Omega} = 16.0\text{ A}. Convert time: Δt=1.50 min×60 s/min=90.0 s\Delta t = 1.50\text{ min} \times 60\text{ s/min} = 90.0\text{ s}. Total charge: Q=IΔt=(16.0 A)(90.0 s)=1.44×103 CQ = I \Delta t = (16.0\text{ A})(90.0\text{ s}) = 1.44 \times 10^3\text{ C} (or 1440 C1440\text{ C}).

03

A rechargeable lithium-ion battery is rated at 3200 mAh3200\text{ mAh} (milliampere-hours). (a) Convert this total charge capacity to coulombs. (b) If the battery discharges steadily at a rate of 0.800 A0.800\text{ A}, find the total operating time in minutes.

Answer

(a) Convert units: 3200 mAh=3.20 A×3600 s=1.152×104 C3200\text{ mAh} = 3.20\text{ A} \times 3600\text{ s} = 1.152 \times 10^4\text{ C} (or 11520 C11520\text{ C}). (b) Operating time in seconds: Δt=QI=11520 C0.800 A=14400 s\Delta t = \frac{Q}{I} = \frac{11520\text{ C}}{0.800\text{ A}} = 14400\text{ s}. Convert to minutes: Δt=14400 s60 s/min=240 min\Delta t = \frac{14400\text{ s}}{60\text{ s/min}} = 240\text{ min} (or directly 3.20 Ah0.800 A=4.00 h=240 min\frac{3.20\text{ Ah}}{0.800\text{ A}} = 4.00\text{ h} = 240\text{ min}).

Loading workspace…