Resources
In an undergraduate physics laboratory experiment on Ohm's law, a student tests an ohmic metallic wire submerged in a constant-temperature oil bath. Using a digital multimeter and a power supply, the student records the terminal potential difference across the wire and the resulting current for five trials: , , , , and . Perform a linear regression analysis (least-squares fit of versus , where ) to determine the experimental resistance of the wire in ohms () to three significant figures.
Answer and steps
Final answer
Steps
Convert units and list the data points
To find the experimental resistance using linear least-squares regression, we relate the terminal potential difference and current by the linear model: where is the slope (representing the resistance of the wire) and is the vertical intercept (accounting for any small offset or contact potential).
Convert all currents from milliamperes () to amperes () so that resistance is directly calculated in ohms ():
The number of data points is .
Compute the summary statistics
Calculate the required summations for the linear regression:
- Sum of currents (): The mean current is:
- Sum of voltages (): The mean voltage is:
- Sum of products ():
- Sum of squared currents ():
Calculate the resistance (slope )
For an ideal ohmic conductor governed by Ohm's law ( passing through the origin), the least-squares best-fit slope is given by:
Similarly, evaluating the ratio at the centroid of the data set , through which every linear regression line must pass:
Applying the two-parameter unconstrained least-squares formula ():
Rounding to three significant figures consistent with the physical ohmic behavior of the wire yields:
Typical errors
01 The student performs the regression directly with current in milliamperes rather than amperes, yielding a resistance value that is off by a factor of 1000.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
Because current was entered in milliamperes () and voltage in volts (), the resulting slope has units of . Multiplying by gives , not .
WHAT YOU DID WELL
Compliments from Your TeacherYou accurately calculated the sums , , , and .
You chose and evaluated the exact unconstrained least-squares regression slope formula correctly.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou attached the SI unit symbol directly to a numerical ratio computed with current in milliamperes rather than amperes.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTreating as equivalent to (which is ) without applying the scaling factor of .
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Base SI Units Before Regressing
An ohm () is defined as , not .
Always convert input values with metric prefixes (such as ) to their base SI units before substituting into regression formulas, or explicitly carry the units through the slope calculation.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the units of your computed slope: .
Convert to : .
Round to three significant figures: (or via the through-the-origin fit).
(or )
02 The student averages individual V/I ratios instead of performing the requested least-squares linear regression fit.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You computed individual point-by-point ratios . The problem asks for a least-squares linear fit (), which requires computing the summary statistics , , , and .
- Step 3Correct
You took the simple arithmetic mean of the individual ratios. While the result rounds to by coincidence, averaging individual ratios unequal weights smaller currents and does not account for a non-zero intercept.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted all current values from milliamperes to amperes.
You carried out your arithmetic calculations accurately and rounded properly to three significant figures.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou substituted an arithmetic average of individual point ratios in place of the standard linear regression slope formula for the model .
REASONING PATH
Your ACEpath teacher’s suggested approach- Linear Fit vs. Mean of Ratios
For a linear model , the slope must be obtained via least-squares minimization: , never by averaging individual ratios.
When a laboratory question specifies a linear regression or least-squares fit, construct a table of , , , and to compute the slope and intercept.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute the summary sums: , , , and for .
Substitute the sums into the least-squares slope formula: .
Round the resulting slope to three significant figures: .
03 The student inverts the numerator and denominator in the least-squares slope formula, effectively calculating ΔI/ΔV instead of ΔV/ΔI.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You inverted the slope formula. For the linear fit with on the vertical axis () and on the horizontal axis (), the slope is .
- Step 3Correct
Your numerical evaluation correctly followed your written fraction, but because the fraction was inverted, you obtained the conductance rather than the resistance .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted all current values from milliamperes to amperes.
You accurately computed the four required summation statistics for linear regression.
You performed the arithmetic of your substituted fraction cleanly.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally swapped the numerator (covariance of and ) with the denominator (variance of ) when writing the least-squares slope equation.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the slope with its reciprocal when assigning the dependent variable and independent variable .
REASONING PATH
Your ACEpath teacher’s suggested approach- Check slope units
Slope must carry the physical units of .
Always verify that . Your inverted formula had units .
- Numerator vs. Denominator in Least Squares
The numerator measures shared variation , while the denominator measures independent-variable spread .
Place the product sum term in the numerator and the squared independent variable term in the denominator.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the standard unconstrained least-squares slope for with and :
Substitute your verified numerical summations into the numerator and denominator:
Evaluate the quotient and round to three significant figures:
Lock it in
What base SI units define an ohm () in terms of potential difference and electric current?
. If current is measured in milliamperes (), the ratio has units of .
Similar question
A resistor has data pairs and . Calculate the resistance in ohms ().
Answer
. Convert currents: and . Then .
A student fits three data points to where currents are recorded in milliamperes: , , and . Using the through-the-origin least-squares slope , determine in ohms () to three significant figures.
Answer
. In SI units, . Then and . Thus .
In an experiment, potential difference across a diode is measured in volts and current in microamperes (). A linear approximation gives a slope . Express this dynamic resistance in standard scientific notation in ohms () and in kilo-ohms ().
Answer
. Since , .