Resources

An uninsulated horizontal steam pipe carries saturated steam through a large room where the ambient air and surrounding walls are both maintained at T∞=Tsurr=20.0∘CT_{\infty} = T_{\text{surr}} = 20.0^{\circ}\text{C} (293.15 K293.15\text{ K}). The outer diameter of the pipe is D=0.100 mD = 0.100\text{ m}, its length is L=5.00 mL = 5.00\text{ m}, and its outer surface temperature is Ts=120.0∘CT_s = 120.0^{\circ}\text{C} (393.15 K393.15\text{ K}). The natural convection heat transfer coefficient over the pipe surface is h=8.50 W/(m2⋅K)h = 8.50\text{ W}/(\text{m}^2\cdot\text{K}), and the pipe surface has an emissivity of ε=0.820\varepsilon = 0.820. Take the Stefan-Boltzmann constant to be σ=5.670×10−8 W/(m2⋅K4)\sigma = 5.670\times 10^{-8}\text{ W}/(\text{m}^2\cdot\text{K}^4). Calculate the ratio of heat lost via radiation to heat lost via natural convection, Q˙radQ˙conv\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}}.

Answer and steps

Final answer

Q˙radQ˙conv=0.812\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} = 0.812.

Steps

01

Formulate the heat transfer equations

To find the ratio of heat transferred by radiation to heat transferred by natural convection, we set up the rate equations for each mechanism over the outer surface of the pipe.

  1. Natural Convection: According to Newton's Law of Cooling, the rate of convective heat transfer from the surface of area AsA_s to the surrounding air is: Q˙conv=hAs(Ts−T∞)\dot{Q}_{\text{conv}} = h A_s (T_s - T_{\infty})
  2. Thermal Radiation: For a small convex object completely enclosed by large surroundings, the net rate of radiation exchange is governed by the Stefan-Boltzmann law: Q˙rad=εσAs(Ts4−Tsurr4)\dot{Q}_{\text{rad}} = \varepsilon \sigma A_s (T_s^4 - T_{\text{surr}}^4)
02

Set up the ratio

Since both modes occur over the same outer surface area As=πDLA_s = \pi D L, the surface area cancels out directly when taking the ratio: Q˙radQ˙conv=εσ(Ts4−Tsurr4)h(Ts−T∞)\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} = \frac{\varepsilon \sigma (T_s^4 - T_{\text{surr}}^4)}{h (T_s - T_{\infty})}

Common Pitfall: Convection relies on the temperature difference, ΔT=Ts−T∞\Delta T = T_s - T_\infty, which is identical in Celsius and Kelvin. However, radiation involves absolute temperatures raised to the fourth power, so TsT_s and TsurrT_{\text{surr}} must be expressed in kelvins (K\text{K}).

03

Substitute the numerical values

  • Surface temperature: Ts=393.15 KT_s = 393.15\text{ K}
  • Surrounding temperature: T∞=Tsurr=293.15 KT_{\infty} = T_{\text{surr}} = 293.15\text{ K}
  • Convective heat transfer coefficient: h=8.50 W/(m2⋅K)h = 8.50\text{ W}/(\text{m}^2\cdot\text{K})
  • Emissivity: ε=0.820\varepsilon = 0.820
  • Stefan-Boltzmann constant: σ=5.670×10−8 W/(m2⋅K4)\sigma = 5.670 \times 10^{-8}\text{ W}/(\text{m}^2\cdot\text{K}^4)

Compute the temperature terms: Ts−T∞=393.15 K−293.15 K=100.0 KT_s - T_{\infty} = 393.15\text{ K} - 293.15\text{ K} = 100.0\text{ K}

Ts4=(393.15)4≈2.3891×1010 K4T_s^4 = (393.15)^4 \approx 2.3891 \times 10^{10}\text{ K}^4 Tsurr4=(293.15)4≈7.3852×109 K4T_{\text{surr}}^4 = (293.15)^4 \approx 7.3852 \times 10^9\text{ K}^4 Ts4−Tsurr4≈2.3891×1010−0.7385×1010=1.6506×1010 K4T_s^4 - T_{\text{surr}}^4 \approx 2.3891 \times 10^{10} - 0.7385 \times 10^{10} = 1.6506 \times 10^{10}\text{ K}^4

Compute the convective heat flux: q˙conv′′=h(Ts−T∞)=8.50⋅100.0=850.0 W/m2\dot{q}''_{\text{conv}} = h (T_s - T_{\infty}) = 8.50 \cdot 100.0 = 850.0\text{ W/m}^2

Compute the radiative heat flux: q˙rad′′=εσ(Ts4−Tsurr4)=(0.820)⋅(5.670×10−8)⋅(1.6506×1010)≈767.4 W/m2\dot{q}''_{\text{rad}} = \varepsilon \sigma (T_s^4 - T_{\text{surr}}^4) = (0.820) \cdot (5.670 \times 10^{-8}) \cdot (1.6506 \times 10^{10}) \approx 767.4\text{ W/m}^2

04

Calculate the final ratio

Q˙radQ˙conv=767.4 W/m2850.0 W/m2≈0.812\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} = \frac{767.4\text{ W/m}^2}{850.0\text{ W/m}^2} \approx 0.812

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses temperatures in Celsius instead of absolute temperatures in Kelvin when evaluating the fourth-power radiation law.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    qconv′′=h⋅(Ts−T∞)=8.50⋅(120−20)=850 W/m2q''_{\text{conv}} = h \cdot (T_s - T_\infty) = 8.50 \cdot (120 - 20) = 850\text{ W/m}^2

  2. Step 2

    qrad′′=ε⋅σ⋅(Ts4−Tsurr4)=0.820⋅(5.670⋅10−8)⋅(1204−204)⟹qrad′′=4.6494⋅10−8⋅(207360000−160000)≈9.63 W/m2q''_{\text{rad}} = \varepsilon \cdot \sigma \cdot (T_s^4 - T_{\text{surr}}^4) = 0.820 \cdot (5.670 \cdot 10^{-8}) \cdot (120^4 - 20^4) \Longrightarrow q''_{\text{rad}} = 4.6494 \cdot 10^{-8} \cdot (207360000 - 160000) \approx 9.63\text{ W/m}^2

    Correct

    qrad′′=εσ(Ts4−Tsurr4)=(0.820)(5.670×10−8)(393.154−293.154)≈767.4 W/m2q''_{\text{rad}} = \varepsilon \sigma (T_s^4 - T_{\text{surr}}^4) = (0.820)(5.670 \times 10^{-8})(393.15^4 - 293.15^4) \approx 767.4\text{ W/m}^2

    You substituted temperatures in degrees Celsius (120120 and 2020) instead of absolute temperatures in kelvins (393.15 K393.15\text{ K} and 293.15 K293.15\text{ K}). Thermal radiation depends on individual absolute thermodynamic temperatures raised to the fourth power, so conversion to kelvins is strictly required.

  3. Step 3

    Q˙rad/Q˙conv=9.63850≈0.0113\dot{Q}_{\text{rad}} / \dot{Q}_{\text{conv}} = \frac{9.63}{850} \approx 0.0113

    Correct

    Q˙radQ˙conv=767.4850.0≈0.812\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} = \frac{767.4}{850.0} \approx 0.812

    Your ratio method was mathematically sound, but this step inherited the incorrect radiative heat flux from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly stated and evaluated Newton's law of cooling for natural convection.

You identified the correct algebraic formula for net radiation exchange between a surface and its surroundings.

You recognized that the surface area cancels when computing the ratio of radiative to convective heat rates.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Absolute vs. Relative Temperature Scales

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You evaluated the fourth-power radiation law using Celsius values rather than absolute temperatures in kelvins, confusing a temperature difference ΔT\Delta T (where 1∘C=1 K1^{\circ}\text{C} = 1\text{ K}) with individual absolute temperatures TT (where T (K)=T (∘C)+273.15T\,(\text{K}) = T\,(^{\circ}\text{C}) + 273.15).

REASONING PATH
Your ACEpath teacher’s suggested approach
Temperature difference vs. absolute temperature
  • If a heat transfer law involves a linear difference (T1−T2)(T_1 - T_2), ΔT\Delta T is identical in kelvins and degrees Celsius. If a law involves temperatures raised to a power like T4T^4, you must always convert each temperature to kelvins first.

  • Check every temperature term before calculating: if it is raised to a power or stands alone outside a difference, convert to kelvins (TK=T∘C+273.15T_\text{K} = T_{^{\circ}\text{C}} + 273.15) immediately.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert both temperatures to absolute kelvins: Ts=120.0+273.15=393.15 KT_s = 120.0 + 273.15 = 393.15\text{ K} and Tsurr=20.0+273.15=293.15 KT_{\text{surr}} = 20.0 + 273.15 = 293.15\text{ K}.

  2. Compute the fourth powers: Ts4=(393.15)4≈2.3891×1010 K4T_s^4 = (393.15)^4 \approx 2.3891 \times 10^{10}\text{ K}^4 and Tsurr4=(293.15)4≈7.3852×109 K4T_{\text{surr}}^4 = (293.15)^4 \approx 7.3852 \times 10^9\text{ K}^4.

  3. Evaluate the radiative heat flux: qrad′′=(0.820)(5.670×10−8)(2.3891×1010−7.3852×109)≈767.4 W/m2q''_{\text{rad}} = (0.820)(5.670 \times 10^{-8})(2.3891 \times 10^{10} - 7.3852 \times 10^9) \approx 767.4\text{ W/m}^2.

  4. Divide by the convective heat flux: Q˙radQ˙conv=767.4 W/m2850.0 W/m2≈0.812\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} = \frac{767.4\text{ W/m}^2}{850.0\text{ W/m}^2} \approx 0.812.

Final answer

Q˙radQ˙conv=0.812\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} = 0.812

NEXT STEPS
Final Takeaways from Your Teacher
  • Review radiation problems and highlight the T4T^4 terms to build the habit of checking for Kelvin conversions.

  • Complete the three targeted flashcards to solidify when Celsius can be used and when Kelvin is mandatory.

  • Attempt the follow-up practice exercises to ensure you compute combined convection and radiation ratios reliably.

OverviewACEpath Teacher's Diagnosis

02 The student incorrectly takes the fourth power of the temperature difference (T_s - T_surr)⁴ instead of the difference of the fourth powers (T_s⁴ - T_surr⁴).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    qconv′′=h⋅ΔT=8.50⋅100.0=850 W/m2q''_{\text{conv}} = h \cdot \Delta T = 8.50 \cdot 100.0 = 850\text{ W/m}^2

  2. Step 2

    qrad′′=ε⋅σ⋅(Ts−Tsurr)4=0.820⋅(5.670×10−8)⋅(393.15−293.15)4⟹qrad′′=4.65 W/m2q''_{\text{rad}} = \varepsilon \cdot \sigma \cdot (T_s - T_{\text{surr}})^4 = 0.820 \cdot (5.670 \times 10^{-8}) \cdot (393.15 - 293.15)^4 \Longrightarrow q''_{\text{rad}} = 4.65\text{ W/m}^2

    Correct

    qrad′′=εσ(Ts4−Tsurr4)=0.820⋅(5.670×10−8)⋅(393.154−293.154)≈767.4 W/m2q''_{\text{rad}} = \varepsilon \sigma (T_s^4 - T_{\text{surr}}^4) = 0.820 \cdot (5.670 \times 10^{-8}) \cdot (393.15^4 - 293.15^4) \approx 767.4\text{ W/m}^2

    Net radiation exchange is the difference between emitted radiation and absorbed radiation, giving (Ts4−Tsurr4)(T_s^4 - T_{\text{surr}}^4), which is mathematically not equal to (Ts−Tsurr)4(T_s - T_{\text{surr}})^4.

  3. Step 3

    Q˙radQ˙conv=4.65850≈0.00547\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} = \frac{4.65}{850} \approx 0.00547

    Correct

    Q˙radQ˙conv=qrad′′qconv′′=767.4850≈0.812\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} = \frac{q''_{\text{rad}}}{q''_{\text{conv}}} = \frac{767.4}{850} \approx 0.812

    Your division was executed correctly based on your prior values, but the final answer is affected by the incorrect radiation flux.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the convective heat flux using Newton's law of cooling.

You properly converted or recognized the temperatures in kelvins for your formulas.

You correctly identified that the ratio of heat transfer rates equals the ratio of heat fluxes because the surface areas cancel out.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Algebraic Pitfall: Difference of Powers vs. Power of Difference

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You applied the exponent to the temperature difference as (Ts−Tsurr)4(T_s - T_{\text{surr}})^4 rather than evaluating the difference between the two independent radiative fluxes, which is proportional to (Ts4−Tsurr4)(T_s^4 - T_{\text{surr}}^4).

REASONING PATH
Your ACEpath teacher’s suggested approach
Net Radiation Balance
  • q˙rad, net′′=q˙emit′′−q˙absorb′′=εσTs4−ασTsurr4=εσ(Ts4−Tsurr4)\dot{q}''_{\text{rad, net}} = \dot{q}''_{\text{emit}} - \dot{q}''_{\text{absorb}} = \varepsilon \sigma T_s^4 - \alpha \sigma T_{\text{surr}}^4 = \varepsilon \sigma (T_s^4 - T_{\text{surr}}^4)

  • Always raise each absolute temperature to the 4th power individually before taking their difference.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Evaluate the difference of the fourth powers: Ts4−Tsurr4=(393.15 K)4−(293.15 K)4≈2.3891×1010−7.3852×109=1.6506×1010 K4T_s^4 - T_{\text{surr}}^4 = (393.15\text{ K})^4 - (293.15\text{ K})^4 \approx 2.3891 \times 10^{10} - 7.3852 \times 10^9 = 1.6506 \times 10^{10}\text{ K}^4.

  2. Compute the correct radiative heat flux: qrad′′=(0.820)(5.670×10−8 W/(m2⋅K4))(1.6506×1010 K4)≈767.4 W/m2q''_{\text{rad}} = (0.820)(5.670 \times 10^{-8}\text{ W}/(\text{m}^2\cdot\text{K}^4))(1.6506 \times 10^{10}\text{ K}^4) \approx 767.4\text{ W/m}^2.

  3. Divide by the convective flux: Q˙radQ˙conv=767.4 W/m2850.0 W/m2≈0.812\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} = \frac{767.4\text{ W/m}^2}{850.0\text{ W/m}^2} \approx 0.812.

Final answer

Q˙radQ˙conv≈0.812\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} \approx 0.812

NEXT STEPS
Final Takeaways from Your Teacher
  • Remember that radiation emission and absorption happen as separate T4T^4 processes, so net radiation is always proportional to T14−T24T_1^4 - T_2^4.

  • Practice evaluating T14−T24T_1^4 - T_2^4 directly on your calculator without subtracting temperatures first.

OverviewACEpath Teacher's Diagnosis

03 The student squares the temperatures instead of raising them to the fourth power in the radiation formula.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    qconv′′=h∗(Ts−T∞)=8.50∗100=850 W/m2q''_{\text{conv}} = h * (T_s - T_\infty) = 8.50 * 100 = 850\text{ W/m}^2

  2. Step 2

    qrad′′=ε∗σ∗(Ts2−Tsurr2)=0.820∗(5.670∗10−8)∗(393.152−293.152)  ⟹  qrad′′=4.6494∗10−8∗(154567−85937)=4.6494∗10−8∗68630≈0.00319 W/m2q''_{\text{rad}} = \varepsilon * \sigma * (T_s^2 - T_{\text{surr}}^2) = 0.820 * (5.670 * 10^{-8}) * (393.15^2 - 293.15^2) \implies q''_{\text{rad}} = 4.6494 * 10^{-8} * (154567 - 85937) = 4.6494 * 10^{-8} * 68630 \approx 0.00319\text{ W/m}^2

    Correct

    qrad′′=εσ(Ts4−Tsurr4)=0.820×(5.670×10−8)×(393.154−293.154)≈767.4 W/m2q''_{\text{rad}} = \varepsilon \sigma (T_s^4 - T_{\text{surr}}^4) = 0.820\times (5.670\times 10^{-8})\times (393.15^4 - 293.15^4) \approx 767.4\text{ W/m}^2

    The Stefan-Boltzmann law dictates that thermal radiation scales with the fourth power of absolute temperature (T4T^4), not the second power (T2T^2).

  3. Step 3

    Q˙radQ˙conv=0.00319850≈3.75∗10−6\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} = \frac{0.00319}{850} \approx 3.75 * 10^{-6}

    Correct

    Q˙radQ˙conv=767.4850.0≈0.812\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} = \frac{767.4}{850.0} \approx 0.812

    This ratio calculation is algebraically consistent with your prior radiative flux, but it inherits the incorrect value from Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly evaluated the temperature difference in kelvins.

You applied Newton's law of cooling accurately to compute the convective heat flux.

You correctly converted the Celsius temperatures to absolute temperatures in kelvins.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Radiation temperature power error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You used an exponent of 2 instead of 4 for the absolute temperatures in the Stefan-Boltzmann radiation equation. Radiative emission depends on T4T^4, so squaring rather than taking the fourth power underestimates radiative emission by several orders of magnitude.

REASONING PATH
Your ACEpath teacher’s suggested approach
Stefan-Boltzmann Fourth-Power Law
  • Net thermal radiation between a gray diffuse surface and surrounding black enclosure is q˙rad′′=εσ(Ts4−Tsurr4)\dot{q}''_{\text{rad}} = \varepsilon \sigma (T_s^4 - T_{\text{surr}}^4), where temperatures must be in kelvins and raised to the 4th power.

  • Always verify that the exponent on absolute temperature in radiation formulas is 4, not 2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the fourth powers of the temperatures: Ts4=(393.15 K)4≈2.3891×1010 K4T_s^4 = (393.15\text{ K})^4 \approx 2.3891\times 10^{10}\text{ K}^4 and Tsurr4=(293.15 K)4≈7.3852×109 K4T_{\text{surr}}^4 = (293.15\text{ K})^4 \approx 7.3852\times 10^9\text{ K}^4.

  2. Find the difference: Ts4−Tsurr4≈1.6506×1010 K4T_s^4 - T_{\text{surr}}^4 \approx 1.6506\times 10^{10}\text{ K}^4.

  3. Compute the correct radiative heat flux: qrad′′=(0.820)(5.670×10−8 W/(m2⋅K4))(1.6506×1010 K4)≈767.4 W/m2q''_{\text{rad}} = (0.820)(5.670\times 10^{-8}\text{ W/(m}^2\cdot\text{K}^4))(1.6506\times 10^{10}\text{ K}^4) \approx 767.4\text{ W/m}^2.

  4. Divide by convective heat flux: Q˙radQ˙conv=qrad′′qconv′′=767.4 W/m2850.0 W/m2≈0.812\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} = \frac{q''_{\text{rad}}}{q''_{\text{conv}}} = \frac{767.4\text{ W/m}^2}{850.0\text{ W/m}^2} \approx 0.812.

Final answer

Q˙radQ˙conv≈0.812\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}} \approx 0.812

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the Stefan-Boltzmann law and memorize that thermal radiation scales with T4T^4.

  • Practice computing radiative heat transfer alongside convective heat transfer to keep their mathematical forms distinct.

Lock it in

Similar question

01

A flat plate has a surface temperature of Ts=77.0∘CT_s = 77.0^{\circ}\text{C} and radiates into large surroundings at Tsurr=27.0∘CT_{\text{surr}} = 27.0^{\circ}\text{C}. If its emissivity is ε=1.00\varepsilon = 1.00 and σ=5.670×10−8 W/(m2⋅K4)\sigma = 5.670 \times 10^{-8}\text{ W}/(\text{m}^2\cdot\text{K}^4), find the net radiative heat flux qrad′′q''_{\text{rad}} in W/m2\text{W/m}^2.

Answer

391 W/m2391\text{ W/m}^2. Convert to absolute temperatures: Ts=77.0+273.15=350.15 KT_s = 77.0 + 273.15 = 350.15\text{ K}, Tsurr=27.0+273.15=300.15 KT_{\text{surr}} = 27.0 + 273.15 = 300.15\text{ K}. Then qrad′′=(1.00)(5.670×10−8)[(350.15)4−(300.15)4]=5.670×10−8(1.5036×1010−8.1270×109)≈391.5 W/m2q''_{\text{rad}} = (1.00)(5.670 \times 10^{-8})[(350.15)^4 - (300.15)^4] = 5.670 \times 10^{-8} (1.5036 \times 10^{10} - 8.1270 \times 10^9) \approx 391.5\text{ W/m}^2 (or 391 W/m2391\text{ W/m}^2 using 350 K350\text{ K} and 300 K300\text{ K}).

02

A heated horizontal duct at Ts=150∘CT_s = 150^{\circ}\text{C} is exposed to air and surroundings at T∞=Tsurr=25∘CT_\infty = T_{\text{surr}} = 25^{\circ}\text{C}. The convection coefficient is h=10.0 W/(m2⋅K)h = 10.0\text{ W}/(\text{m}^2\cdot\text{K}) and emissivity is ε=0.900\varepsilon = 0.900. Using σ=5.670×10−8 W/(m2⋅K4)\sigma = 5.670 \times 10^{-8}\text{ W}/(\text{m}^2\cdot\text{K}^4), determine the ratio of radiation to convection heat transfer, Q˙radQ˙conv\frac{\dot{Q}_{\text{rad}}}{\dot{Q}_{\text{conv}}}.

Answer

0.9850.985. Convective heat flux: qconv′′=10.0×(150−25)=1250 W/m2q''_{\text{conv}} = 10.0 \times (150 - 25) = 1250\text{ W/m}^2. Radiative heat flux with Ts=423.15 KT_s = 423.15\text{ K} and Tsurr=298.15 KT_{\text{surr}} = 298.15\text{ K}: qrad′′=(0.900)(5.670×10−8)[(423.15)4−(298.15)4]≈5.103×10−8(3.2057×1010−7.8988×109)≈1233 W/m2q''_{\text{rad}} = (0.900)(5.670 \times 10^{-8})[(423.15)^4 - (298.15)^4] \approx 5.103 \times 10^{-8} (3.2057 \times 10^{10} - 7.8988 \times 10^9) \approx 1233\text{ W/m}^2. Ratio: 12331250≈0.985\frac{1233}{1250} \approx 0.985.

03

At what surface temperature TsT_s (in ∘C^{\circ}\text{C}) will the radiation heat flux from a blackbody surface (ε=1.00\varepsilon = 1.00) exactly equal its convective heat flux, given T∞=Tsurr=300 KT_\infty = T_{\text{surr}} = 300\text{ K} and h=12.0 W/(m2⋅K)h = 12.0\text{ W}/(\text{m}^2\cdot\text{K})? (Hint: Set σ(Ts4−3004)=h(Ts−300)\sigma(T_s^4 - 300^4) = h(T_s - 300) and use the approximation Ts4−T04≈4Tavg3(Ts−T0)T_s^4 - T_0^4 \approx 4 T_{\text{avg}}^3 (T_s - T_0) or test a nearby value).

Answer

Ts≈87∘CT_s \approx 87^{\circ}\text{C} (360 K360\text{ K}). Equating fluxes: σ(Ts4−3004)=h(Ts−300)  ⟹  σ(Ts+300)(Ts2+3002)=h=12.0\sigma(T_s^4 - 300^4) = h(T_s - 300) \implies \sigma(T_s + 300)(T_s^2 + 300^2) = h = 12.0. Substituting Ts=360 KT_s = 360\text{ K}: (5.670×10−8)(660)(3602+3002)=(3.742×10−5)(129600+90000)=(3.742×10−5)(219600)≈8.22 W/m2⋅K(5.670 \times 10^{-8})(660)(360^2 + 300^2) = (3.742 \times 10^{-5})(129600 + 90000) = (3.742 \times 10^{-5})(219600) \approx 8.22\text{ W/m}^2\cdot\text{K} (too low). Solving σ(Ts2+3002)(Ts+300)=12.0\sigma (T_s^2 + 300^2)(T_s + 300) = 12.0 yields Ts≈413 K≈140∘CT_s \approx 413\text{ K} \approx 140^{\circ}\text{C}.

Loading workspace…