Resources

An industrial flywheel with an outer radius of R=0.650 mR = 0.650\text{ m} rotates at a steady rate. A point on the outer rim travels with a linear speed of v1=31.2 m/sv_1 = 31.2\text{ m/s}. To monitor internal stresses, an optical sensor is positioned to track a point located at an internal radius r2r_2 where the tangential linear speed is measured to be v2=19.2 m/sv_2 = 19.2\text{ m/s}. Assuming rigid-body rotation, determine (a) the constant angular speed ω\omega of the flywheel, and (b) the radial distance r2r_2 of the internal sensor from the rotation axis. Round both values to three significant figures.

Answer and steps

Final answer

(a) ω=48.0 rad/s\omega = 48.0\text{ rad/s}; (b) r2=0.400 mr_2 = 0.400\text{ m}

Steps

01

Calculate the Angular Speed ω\omega of the Flywheel

Key Concept: Relationship Between Tangential and Angular Speed

In rigid-body rotation, every part of the object completes one full turn in the exact same amount of time. Consequently, every point on the object shares the same angular speed ω\omega. The linear (tangential) speed vv of a point moving in a circular path of radius rr around the axis of rotation is directly proportional to both the angular speed and the distance from the axis: v=ωrv = \omega r

A point on the outer rim is at a radial distance r1=R=0.650 mr_1 = R = 0.650\text{ m} and travels with linear speed v1=31.2 m/sv_1 = 31.2\text{ m/s}.

Rearranging the relation v1=ωRv_1 = \omega R to solve for angular speed:

ω=v1R\omega = \frac{v_1}{R}

Substitute the given numerical values:

ω=31.2 m/s0.650 m=48.0 rad/s\omega = \frac{31.2\text{ m/s}}{0.650\text{ m}} = 48.0\text{ rad/s}


02

Determine the Internal Radial Distance r2r_2

Because the flywheel is a rigid body, the internal point monitored by the sensor rotates with this same angular speed ω=48.0 rad/s\omega = 48.0\text{ rad/s}.

Using the tangential speed equation for the internal point:

v2=ωr2v_2 = \omega r_2

Solving for r2r_2:

r2=v2ωr_2 = \frac{v_2}{\omega}

Substitute the measured speed v2=19.2 m/sv_2 = 19.2\text{ m/s} and the calculated angular speed:

r2=19.2 m/s48.0 rad/s=0.400 mr_2 = \frac{19.2\text{ m/s}}{48.0\text{ rad/s}} = 0.400\text{ m}

(Alternative check via direct ratio: Since v∝rv \propto r for constant ω\omega, r2R=v2v1  ⟹  r2=0.650 m⋅19.2 m/s31.2 m/s=0.400 m\frac{r_2}{R} = \frac{v_2}{v_1} \implies r_2 = 0.650\text{ m} \cdot \frac{19.2\text{ m/s}}{31.2\text{ m/s}} = 0.400\text{ m}.)


Common Pitfall to Avoid

  • Equating linear speeds: Points at different distances from the center do not have the same linear speed. Only the angular speed ω\omega is identical for all points on a rotating rigid body. Tangential velocity increases linearly with distance from the central axis.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misinverts the relationship between linear speed and angular velocity as ω = v · R instead of ω = v / R.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ω=v1⋅R  ⟹  ω=31.2⋅0.650=20.3 rad/s\omega = v_1 \cdot R \implies \omega = 31.2 \cdot 0.650 = 20.3\text{ rad/s}

    Correct

    ω=v1R=31.2 m/s0.650 m=48.0 rad/s\omega = \frac{v_1}{R} = \frac{31.2\text{ m/s}}{0.650\text{ m}} = 48.0\text{ rad/s}

    You multiplied linear speed by the radius rather than dividing. From the fundamental circular motion equation v=ωRv = \omega R, isolating angular speed gives ω=vR\omega = \frac{v}{R}.

  2. Step 2

    r2=v2ω  ⟹  r2=19.220.3=0.946 mr_2 = \frac{v_2}{\omega} \implies r_2 = \frac{19.2}{20.3} = 0.946\text{ m}

    Correct

    r2=v2ω=19.2 m/s48.0 rad/s=0.400 mr_2 = \frac{v_2}{\omega} = \frac{19.2\text{ m/s}}{48.0\text{ rad/s}} = 0.400\text{ m}

    Your formula r2=v2ωr_2 = \frac{v_2}{\omega} and your algebraic substitution were correct, but substituting your earlier incorrect value of ω=20.3 rad/s\omega = 20.3\text{ rad/s} resulted in an incorrect numerical distance. Notice that an internal radius must also be smaller than the outer radius of 0.650 m0.650\text{ m}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that both points on the rigid flywheel share the same angular speed ω\omega.

You correctly rearranged v=ωrv = \omega r into r2=v2ωr_2 = \frac{v_2}{\omega} when solving for the unknown internal radius.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Inversion / Dimensional Error

You wrote ω=v1⋅R\omega = v_1 \cdot R instead of ω=v1R\omega = \frac{v_1}{R}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You misremembered the algebraic rearrangement of v=ωrv = \omega r, treating angular speed as a product of linear speed and distance rather than a ratio.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Consistency Check
  • Linear speed has units of m/s\text{m/s} and radius has units of m\text{m}, so angular speed must have units of m/sm=s−1=rad/s\frac{\text{m/s}}{\text{m}} = \text{s}^{-1} = \text{rad/s}.

  • Always verify that your formula yields the proper units before computing numerical values: multiplying v⋅Rv \cdot R produces m2/s\text{m}^2/\text{s}, not rad/s\text{rad/s}.

Physical Reality Check
  • An internal radius must be strictly less than the outer radius (r2<Rr_2 < R).

  • If your calculated internal radius exceeds the outer rim radius (0.946 m>0.650 m0.946\text{ m} > 0.650\text{ m}), pause and inspect the preceding angular speed calculation.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Rearrange v1=ωRv_1 = \omega R to solve for angular speed: ω=v1R\omega = \frac{v_1}{R}.

  2. Substitute the given values for the rim: ω=31.2 m/s0.650 m=48.0 rad/s\omega = \frac{31.2\text{ m/s}}{0.650\text{ m}} = 48.0\text{ rad/s}.

  3. Use the constant angular speed to find the internal radius: r2=v2ω=19.2 m/s48.0 rad/s=0.400 mr_2 = \frac{v_2}{\omega} = \frac{19.2\text{ m/s}}{48.0\text{ rad/s}} = 0.400\text{ m}.

Final answer

(a) ω=48.0 rad/s\omega = 48.0\text{ rad/s}; (b) r2=0.400 mr_2 = 0.400\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice isolating variables from the base definition v=ωrv = \omega r before substituting numbers.

  • Check that units cancel correctly: m/sm=rad/s\frac{\text{m/s}}{\text{m}} = \text{rad/s} and m/srad/s=m\frac{\text{m/s}}{\text{rad/s}} = \text{m}.

  • Compare internal and external values to verify that smaller tangential speed corresponds to a smaller radius.

OverviewACEpath Teacher's Diagnosis

02 The student assumes tangential linear speed is constant across all radii rather than angular speed, setting r₂ based on an inverse proportionality to linear speed.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ω=v1R  ⟹  ω=31.20.650=48.0 rad/s\omega = \frac{v_1}{R} \implies \omega = \frac{31.2}{0.650} = 48.0\text{ rad/s}

  2. Step 2

    v1⋅R=v2⋅r2  ⟹  r2=v1⋅Rv2  ⟹  r2=31.2⋅0.65019.2=1.06 mv_1 \cdot R = v_2 \cdot r_2 \implies r_2 = \frac{v_1 \cdot R}{v_2} \implies r_2 = \frac{31.2 \cdot 0.650}{19.2} = 1.06\text{ m}

    Correct

    v2=ωr2  ⟹  r2=v2ω=19.2 m/s48.0 rad/s=0.400 mv_2 = \omega r_2 \implies r_2 = \frac{v_2}{\omega} = \frac{19.2\text{ m/s}}{48.0\text{ rad/s}} = 0.400\text{ m}

    In a rotating rigid body, all points share the same angular speed ω\omega, meaning tangential speed is directly proportional to radius (v=ωrv = \omega r), so v1R=v2r2\frac{v_1}{R} = \frac{v_2}{r_2}. Equating the products v1R=v2r2v_1 R = v_2 r_2 assumes an inverse proportion, which incorrectly yields a radius r2=1.06 mr_2 = 1.06\text{ m} that is larger than the entire flywheel.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the formula connecting linear speed and angular speed for the outer rim.

You calculated the correct numerical value and units for the angular speed ω\omega.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverse Proportionality Misconception in Rigid-Body Rotation

You set the product v⋅rv \cdot r as constant instead of the ratio vr=ω\frac{v}{r} = \omega.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated linear speed as inversely proportional to radius rather than directly proportional. In rigid-body rotation, points farther from the axis must cover greater distances in the same time period, so tangential speed increases linearly with radius (v=ωrv = \omega r). A point with lower speed must therefore lie at a smaller radius.

REASONING PATH
Your ACEpath teacher’s suggested approach
Rigid-Body Constant
  • Every point on a rotating rigid body shares the exact same angular velocity ω\omega.

  • Always relate linear speeds at different radii using v1r1=v2r2=ω\frac{v_1}{r_1} = \frac{v_2}{r_2} = \omega.

Sanity Check Radius vs. Speed
  • Because v=ωrv = \omega r, a smaller linear speed requires a smaller radial distance.

  • Check that an internal point has r<Rr < R whenever v<vrimv < v_{\text{rim}}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the shared angular speed ω=48.0 rad/s\omega = 48.0\text{ rad/s} found in part (a).

  2. Apply the tangential speed formula for the internal sensor: v2=ωr2v_2 = \omega r_2.

  3. Solve for the internal radius: r2=v2ω=19.2 m/s48.0 rad/s=0.400 mr_2 = \frac{v_2}{\omega} = \frac{19.2\text{ m/s}}{48.0\text{ rad/s}} = 0.400\text{ m}.

Final answer

(a) ω=48.0 rad/s\omega = 48.0\text{ rad/s}; (b) r2=0.400 mr_2 = 0.400\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between rigid-body rotation (v∝rv \propto r, ω=constant\omega = \text{constant}) and orbital/inverse relations (v∝1rv \propto \frac{1}{r}).

  • Complete the targeted practice exercises below to reinforce applying v=ωrv = \omega r across different points on a single rotating body.

OverviewACEpath Teacher's Diagnosis

03 The student inverts the radius formula in part (b) by writing r₂ = ω / v₂ instead of r₂ = v₂ / ω.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ω=v1R  ⟹  ω=31.20.650=48.0 rad/s\omega = \frac{v_1}{R} \implies \omega = \frac{31.2}{0.650} = 48.0\text{ rad/s}

  2. Step 2

    r2=ωv2  ⟹  r2=48.019.2=2.50 mr_2 = \frac{\omega}{v_2} \implies r_2 = \frac{48.0}{19.2} = 2.50\text{ m}

    Correct

    r2=v2ω=19.2 m/s48.0 rad/s=0.400 mr_2 = \frac{v_2}{\omega} = \frac{19.2\text{ m/s}}{48.0\text{ rad/s}} = 0.400\text{ m}

    To isolate r2r_2 from the relationship v2=ωr2v_2 = \omega r_2, you need to divide both sides by ω\omega, giving r2=v2ωr_2 = \frac{v_2}{\omega}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied the linear-to-angular speed relationship v=ωrv = \omega r for the outer rim.

You carried the correct numerical value for ω\omega into part (b).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Algebraic Inversion Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You inverted the quotient when isolating radius from v=ωrv = \omega r, dividing angular speed by linear speed instead of linear speed by angular speed.

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolating Variables in Multiplicative Relations
  • For a=b⋅ca = b \cdot c, isolating cc requires dividing both sides by bb: c=abc = \frac{a}{b}.

  • Always write the fundamental law v=ωrv = \omega r first, then divide both sides by ω\omega step-by-step to get r=vωr = \frac{v}{\omega}.

Physical Sanity Check and Dimensional Analysis
  • An internal radius must be strictly smaller than the outer radius (r2<Rr_2 < R), and units must simplify to meters (m/srad/s=m\frac{\text{m/s}}{\text{rad/s}} = \text{m}, whereas rad/sm/s=m−1\frac{\text{rad/s}}{\text{m/s}} = \text{m}^{-1}).

  • Verify that your calculated distance (2.50 m2.50\text{ m}) does not exceed the total outer radius (0.650 m0.650\text{ m}).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the relationship between tangential speed and angular speed: v2=ωr2v_2 = \omega r_2.

  2. Divide both sides by ω\omega to isolate r2r_2: r2=v2ωr_2 = \frac{v_2}{\omega}.

  3. Substitute v2=19.2 m/sv_2 = 19.2\text{ m/s} and ω=48.0 rad/s\omega = 48.0\text{ rad/s}: r2=19.248.0=0.400 mr_2 = \frac{19.2}{48.0} = 0.400\text{ m}.

Final answer

(a) ω=48.0 rad/s\omega = 48.0\text{ rad/s}; (b) r2=0.400 mr_2 = 0.400\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review one-step algebraic rearrangement for three-variable physics formulas like v=ωrv = \omega r.

  • Perform a quick dimensional and physical reasonableness check on every calculated answer.

Lock it in

Similar question

01

A compact disc with radius R=0.060 mR = 0.060\text{ m} spins at a constant rate. A track at the outer perimeter moves with a linear speed of v=1.26 m/sv = 1.26\text{ m/s}. Find the angular speed ω\omega of the disc.

Answer

ω=21.0 rad/s\omega = 21.0\text{ rad/s}. Using ω=vR=1.26 m/s0.060 m=21.0 rad/s\omega = \frac{v}{R} = \frac{1.26\text{ m/s}}{0.060\text{ m}} = 21.0\text{ rad/s}.

02

A carousel rotates at a steady rate. A child riding an outer horse at r1=5.0 mr_1 = 5.0\text{ m} from the center travels at v1=3.5 m/sv_1 = 3.5\text{ m/s}. What is the linear speed v2v_2 of another child seated on an inner horse at r2=3.0 mr_2 = 3.0\text{ m} from the center?

Answer

v2=2.1 m/sv_2 = 2.1\text{ m/s}. First find angular speed: ω=v1r1=3.55.0=0.70 rad/s\omega = \frac{v_1}{r_1} = \frac{3.5}{5.0} = 0.70\text{ rad/s}. Then calculate inner linear speed: v2=ωr2=(0.70)(3.0)=2.1 m/sv_2 = \omega r_2 = (0.70)(3.0) = 2.1\text{ m/s} (or directly via ratio: v2=v1⋅r2r1=3.5⋅3.05.0=2.1 m/sv_2 = v_1 \cdot \frac{r_2}{r_1} = 3.5 \cdot \frac{3.0}{5.0} = 2.1\text{ m/s}).

03

A circular grinding stone has an outer diameter of 0.500 m0.500\text{ m} (outer radius R=0.250 mR = 0.250\text{ m}). A point on the outer edge moves at 45.0 m/s45.0\text{ m/s}. At what distance rtargetr_{\text{target}} from the central axis does the linear speed equal 18.0 m/s18.0\text{ m/s}?

Answer

rtarget=0.100 mr_{\text{target}} = 0.100\text{ m}. Calculate angular speed: ω=vedgeR=45.0 m/s0.250 m=180 rad/s\omega = \frac{v_{\text{edge}}}{R} = \frac{45.0\text{ m/s}}{0.250\text{ m}} = 180\text{ rad/s}. Then find target radius: rtarget=vtargetω=18.0 m/s180 rad/s=0.100 mr_{\text{target}} = \frac{v_{\text{target}}}{\omega} = \frac{18.0\text{ m/s}}{180\text{ rad/s}} = 0.100\text{ m}.

Loading workspace…