Resources
Two air-filled parallel-plate capacitors with capacitances and have identical plate spacing but different dielectric breakdown voltages. Capacitor can safely withstand a maximum potential difference of before dielectric breakdown occurs, whereas can withstand up to . If these two capacitors are connected in series, determine the maximum safe DC voltage that can be applied across the entire series combination without exceeding the breakdown rating of either capacitor, and identify which capacitor reaches its critical threshold first.
Answer and steps
Final answer
( reaches breakdown first)
Steps
- Analyze the voltage distribution across series capacitors: For two capacitors and connected in series across a total DC source voltage , the fraction of the total voltage appearing across each capacitor is determined by the series combination rule:
- Substitute the given capacitance values: With and , the total capacitance sum is: The corresponding voltage sharing factors are:
-
Determine the maximum permissible source voltage for each capacitor:
- To keep capacitor within its maximum rating of :
- To keep capacitor within its maximum rating of :
- Identify the limiting capacitor and maximum safe voltage: Comparing the two thresholds, capacitor reaches its critical breakdown limit at a much lower applied source voltage (). Therefore, reaches breakdown first, and the maximum safe applied DC source voltage is:
Typical errors
01 The student simply adds the individual breakdown voltages together, assuming the total safe voltage is the sum of maximum rated voltages without accounting for unequal charge-based voltage division.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You directly added the individual breakdown voltages together. In a series circuit, each capacitor carries the voltage according to the circuit's voltage distribution, so the maximum safe total voltage is limited by whichever capacitor reaches its rating first, not the sum of their individual maxima.
- Step 2
Both reach their breakdown voltages simultaneously at 200 V.
Correctreaches breakdown first.
You stated that both capacitors reach their breakdown voltages simultaneously. Because the two capacitors have different capacitances and different ratings, the voltage distribution causes one capacitor to hit its critical threshold at a lower source voltage than the other.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the two individual breakdown voltage ratings given in the problem.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou assumed that capacitors in series share voltage equally or can simultaneously operate at their maximum breakdown ratings, overlooking how capacitance determines voltage division across series elements.
REASONING PATH
Your ACEpath teacher’s suggested approach- Voltage Division in Series
In a series circuit, the total voltage is distributed among the components based on their individual values rather than allowing each component to independently reach its maximum rating simultaneously.
Always find the fraction of the applied source voltage that appears across each component before checking against individual safety limits.
- Identify the Limiting Component
The maximum permissible source voltage is set by the most restrictive condition: .
Calculate the source voltage that causes each capacitor to reach its rating, then choose the smaller value.
CORRECTED PATH
ACEpath Teacher's DemonstrationFind the voltage sharing factor for each capacitor using and , where .
The fraction across is , requiring .
The fraction across is , requiring .
( reaches breakdown first)
02 The student mistakenly assumes that the capacitor with the lower voltage rating limits the circuit and limits total charge by C2, calculating Vsource,max from Q2,max instead of Q1,max.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
The circuit is limited by the lower rated voltage , so
CorrectCapacitors connected in series must store the exact same charge . To prevent dielectric breakdown in both components, the total series charge must be restricted by the smaller maximum charge threshold, not the larger one.
- Step 4Correct
Your formula is algebraically sound, but the result is affected by substituting instead of .
- Step 5
Capacitor reaches its breakdown threshold first because its breakdown voltage is lower (50.0 V vs. 150 V).
CorrectCapacitor reaches its breakdown threshold first because its maximum charge capacity () is reached before 's capacity ().
Because voltage in a series combination divides inversely with capacitance (), the smaller capacitor carries four times the voltage of at any shared charge level, causing to reach its limit first.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the maximum safe charge for each individual capacitor.
You accurately found the equivalent series capacitance .
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou selected the limiting condition based directly on the individual voltage rating rather than identifying that series elements share an identical charge , which makes the minimum charge capacity the true governing constraint.
REASONING PATH
Your ACEpath teacher’s suggested approach- Series Charge Invariance
Capacitors in series store identical charge: .
Always find each component's charge limit and take the minimum value across all components in series.
- Inverse Voltage Sharing
For series capacitors, , meaning the smaller capacitor drops a larger voltage.
Do not assume the capacitor with the lowest voltage rating fails first; compare charge limits rather than voltage ratings directly.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompare the maximum safe charges: and .
Set the maximum safe circuit charge to the smaller limit: . This means reaches breakdown first.
Compute the maximum safe source voltage: (or equivalently, ).
( reaches breakdown first)
03 The student assumes voltage divides proportionally to capacitance rather than inversely in series, writing V1/Vtotal = C1/(C1+C2).
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You applied a direct voltage-divider formula (). However, series components share equal charge (), so dictates that voltage divides inversely with capacitance: and .
- Step 2Correct
Your inequality method and arithmetic were correct, but they inherited the inverted voltage fractions from Step 1.
- Step 3
, Capacitor reaches its critical threshold first because .
Correct, Capacitor reaches its critical threshold first because .
Because , capacitor actually reaches its breakdown voltage first at a maximum safe source voltage of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly set up inequality constraints based on each capacitor's maximum voltage rating.
You recognized that the overall maximum safe voltage is governed by whichever capacitor hits its limit at the lowest source voltage.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeWHY IT HAPPENED
ACEpath Teacher's DiagnosisYou used the resistive voltage-divider formula () for capacitors in series. Because series capacitors hold equal charge (), potential difference is inversely proportional to capacitance (), meaning smaller capacitors sustain larger voltage drops.
REASONING PATH
Your ACEpath teacher’s suggested approach- Series Charge Invariance
Capacitors in series all store the exact same magnitude of charge: .
Start series capacitor problems by equating charges, not by assuming direct voltage sharing.
- Capacitive Voltage Divider Rule
For two capacitors in series: and .
Put the opposite capacitor's value in the numerator when finding the voltage across a specific series capacitor.
CORRECTED PATH
ACEpath Teacher's DemonstrationRecall that for series capacitors, equal charge implies and , giving and .
Set the breakdown constraints: for , and for .
Select the limiting threshold: limits the source to .
( reaches breakdown first)
Lock it in
Can you find the maximum safe source voltage for components in series by simply adding their individual maximum voltage ratings?
No. Components in series divide the source voltage based on their parameters, so one component typically reaches its safe limit before the others.
Similar question
Two series capacitors take voltage fractions of and . If their maximum allowable voltages are and , find the maximum safe source voltage and which capacitor limits it.
Answer
( limits it). For , . For , . The smaller value limits the circuit.
Two capacitors are connected in series such that and . Capacitor can withstand up to , while can withstand up to . What is the maximum safe source voltage, and what is the voltage across at this maximum?
Answer
, and . For , . For , . Thus, , giving .
A series pair of capacitors has voltage division ratios of across and across . Their breakdown ratings are and . If a student erroneously adds their ratings to get , what voltage would actually appear across , and by how much does it exceed 's rating?
Answer
, which exceeds the limit by . At , . Since the rating is , it exceeds the rating by , leading to dielectric breakdown.