Resources

A physics student incorrectly predicts that inserting a dielectric slab between the plates of one capacitor in a series network will reduce the voltage across that specific capacitor while increasing its stored charge. To test this, two identical capacitors, each with capacitance C0=10.0  μFC_0 = 10.0\;\mu\text{F}, are connected in series across an ideal battery of fixed voltage V=24.0 VV = 24.0\text{ V}. A solid dielectric slab with dielectric constant κ=3.00\kappa = 3.00 is then fully inserted into the gap of the second capacitor (C2C_2) while the battery remains permanently connected. Calculate the new potential difference across C2C_2 and the change in charge ΔQ1\Delta Q_1 on the un-modified capacitor C1C_1.

Answer and steps

Final answer

V2=6.00 VV_2 = 6.00\text{ V}, ΔQ1=+60.0  μC\Delta Q_1 = +60.0\;\mu\text{C}

Steps

01

Analyze the Initial State

Before the dielectric slab is inserted, two identical capacitors, each with capacitance C0=10.0 μFC_0 = 10.0\text{ }\mu\text{F}, are connected in series across a battery of voltage V=24.0 VV = 24.0\text{ V}.

The equivalent capacitance of two identical capacitors in series is: Ceq, initial=C0⋅C0C0+C0=C02=10.0 μF2=5.00 μFC_{\text{eq, initial}} = \frac{C_0 \cdot C_0}{C_0 + C_0} = \frac{C_0}{2} = \frac{10.0\text{ }\mu\text{F}}{2} = 5.00\text{ }\mu\text{F}

Since capacitors connected in series carry equal charge, the initial charge on each capacitor (Q1Q_1 and Q2Q_2) is: Qinitial=Ceq, initial⋅V=(5.00 μF)(24.0 V)=120 μCQ_{\text{initial}} = C_{\text{eq, initial}} \cdot V = (5.00\text{ }\mu\text{F})(24.0\text{ V}) = 120\text{ }\mu\text{C}


02

Determine the Capacitance and Charge After Dielectric Insertion

When a dielectric slab with κ=3.00\kappa = 3.00 is fully inserted into the second capacitor (C2C_2), its capacitance increases by a factor of κ\kappa: C2′=κC0=3.00⋅10.0 μF=30.0 μFC_2' = \kappa C_0 = 3.00 \cdot 10.0\text{ }\mu\text{F} = 30.0\text{ }\mu\text{F}

The first capacitor remains unchanged: C1=10.0 μFC_1 = 10.0\text{ }\mu\text{F}

The new equivalent series capacitance becomes: Ceq, new=C1⋅C2′C1+C2′=(10.0 μF)(30.0 μF)10.0 μF+30.0 μF=30040.0 μF=7.50 μFC_{\text{eq, new}} = \frac{C_1 \cdot C_2'}{C_1 + C_2'} = \frac{(10.0\text{ }\mu\text{F})(30.0\text{ }\mu\text{F})}{10.0\text{ }\mu\text{F} + 30.0\text{ }\mu\text{F}} = \frac{300}{40.0}\text{ }\mu\text{F} = 7.50\text{ }\mu\text{F}

Because the battery remains connected at a constant potential difference V=24.0 VV = 24.0\text{ V}, the new total charge drawn by the series combination is: Qnew=Ceq, new⋅V=(7.50 μF)(24.0 V)=180 μCQ_{\text{new}} = C_{\text{eq, new}} \cdot V = (7.50\text{ }\mu\text{F})(24.0\text{ V}) = 180\text{ }\mu\text{C}

In a series circuit, each capacitor carries the same total charge: Q1′=Q2′=Qnew=180 μCQ_1' = Q_2' = Q_{\text{new}} = 180\text{ }\mu\text{C}


03

Calculate the New Potential Difference Across C2C_2

Using the definition of capacitance V=QCV = \frac{Q}{C}: V2=QnewC2′=180 μC30.0 μF=6.00 VV_2 = \frac{Q_{\text{new}}}{C_2'} = \frac{180\text{ }\mu\text{C}}{30.0\text{ }\mu\text{F}} = 6.00\text{ V}

(Alternative check using the capacitive voltage divider formula: V2=V⋅C1C1+C2′=24.0 V⋅10.040.0=6.00 VV_2 = V \cdot \frac{C_1}{C_1 + C_2'} = 24.0\text{ V} \cdot \frac{10.0}{40.0} = 6.00\text{ V}.)


04

Calculate the Change in Charge on C1C_1

The change in charge on the un-modified capacitor C1C_1 is: ΔQ1=Q1′−Q1=180 μC−120 μC=+60.0 μC\Delta Q_1 = Q_1' - Q_1 = 180\text{ }\mu\text{C} - 120\text{ }\mu\text{C} = +60.0\text{ }\mu\text{C}

Common Pitfall: A common mistake is to assume that because C1C_1 was physically untouched, its charge must stay constant. In a series circuit, altering one component changes the total equivalent capacitance of the entire branch. Because the battery maintains a fixed total voltage, more charge is pulled through the entire series loop, increasing the stored charge on both capacitors.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misapplies the parallel voltage divider formula directly proportional to capacitance rather than inversely proportional to capacitance for series capacitors.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    C1=10.0  μF,  C2′=3.00⋅10.0  μF=30.0  μFC_1 = 10.0\;\mu\text{F},\; C_2' = 3.00 \cdot 10.0\;\mu\text{F} = 30.0\;\mu\text{F}

  2. Step 2

    V2′=V⋅C2′C1+C2′  ⟹  V2′=24.0⋅30.040.0=18.0 VV_2' = \frac{V \cdot C_2'}{C_1 + C_2'} \implies V_2' = \frac{24.0 \cdot 30.0}{40.0} = 18.0\text{ V}

    Correct

    V2′=V(C1C1+C2′)=24.0 V(10.040.0)=6.00 VV_2' = V \left(\frac{C_1}{C_1 + C_2'}\right) = 24.0\text{ V} \left(\frac{10.0}{40.0}\right) = 6.00\text{ V}

    For capacitors in series, the charge QQ is identical across both elements, so potential difference is inversely proportional to capacitance (V=Q/CV = Q/C). The voltage across C2C_2 depends on the ratio C1C1+C2′\frac{C_1}{C_1 + C_2'}, not C2′C1+C2′\frac{C_2'}{C_1 + C_2'}.

  3. Step 3

    Qinitial=(10.02)⋅24.0=120  μC  ⟹  Ceq′=10.0⋅30.010.0+30.0=7.50  μF  ⟹  Q′=7.50⋅24.0=180  μC  ⟹  ΔQ1=180−120=+60.0  μCQ_{\text{initial}} = \left(\frac{10.0}{2}\right) \cdot 24.0 = 120\;\mu\text{C} \implies C_{\text{eq}}' = \frac{10.0 \cdot 30.0}{10.0 + 30.0} = 7.50\;\mu\text{F} \implies Q' = 7.50 \cdot 24.0 = 180\;\mu\text{C} \implies \Delta Q_1 = 180 - 120 = +60.0\;\mu\text{C}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly multiplied by the dielectric constant to find the new capacitance C2′C_2'.

You accurately computed the equivalent capacitance and charge for both the initial and final circuit states.

You correctly subtracted initial charge from final charge to find ΔQ1\Delta Q_1.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Voltage Divider Ratio

No, this is a conceptual confusion between capacitive and resistive voltage dividers.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Because capacitors in series carry the exact same charge QQ, their voltages relate via V=Q/CV = Q/C. Consequently, the voltage across each capacitor is inversely proportional to its capacitance: the larger capacitor takes the smaller share of the total voltage. Using the direct proportional formula V2=VC2C1+C2V_2 = V \frac{C_2}{C_1 + C_2} incorrectly treats capacitors like series resistors.

REASONING PATH
Your ACEpath teacher’s suggested approach
Capacitive Voltage Divider Rule
  • In a two-capacitor series loop, V1=Vtotal(C2C1+C2)V_1 = V_{\text{total}} \left(\frac{C_2}{C_1 + C_2}\right) and V2=Vtotal(C1C1+C2)V_2 = V_{\text{total}} \left(\frac{C_1}{C_1 + C_2}\right).

  • Always place the opposite capacitor's value in the numerator when finding the voltage across one series capacitor, or simply use V2=QnewC2′V_2 = \frac{Q_{\text{new}}}{C_2'} directly.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recall that in a series circuit, each capacitor carries the same charge Q′=180  μCQ' = 180\;\mu\text{C}.

  2. Apply V2′=Q′C2′V_2' = \frac{Q'}{C_2'} directly: V2′=180  μC30.0  μF=6.00 VV_2' = \frac{180\;\mu\text{C}}{30.0\;\mu\text{F}} = 6.00\text{ V}.

  3. Alternatively, use the inverse voltage divider formula: V2′=24.0 V⋅10.0  μF10.0  μF+30.0  μF=6.00 VV_2' = 24.0\text{ V} \cdot \frac{10.0\;\mu\text{F}}{10.0\;\mu\text{F} + 30.0\;\mu\text{F}} = 6.00\text{ V}.

Final answer

V2=6.00 V,  ΔQ1=+60.0  μCV_2 = 6.00\text{ V},\; \Delta Q_1 = +60.0\;\mu\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Notice that you already had Q′=180  μCQ' = 180\;\mu\text{C} in your later steps; dividing that by C2′=30.0  μFC_2' = 30.0\;\mu\text{F} gives 6.00 V6.00\text{ V} immediately and avoids voltage-divider confusion.

  • Remember the inverse relationship for series capacitors: larger capacitance means smaller voltage drop.

OverviewACEpath Teacher's Diagnosis

02 The student incorrectly calculates the equivalent capacitance by adding capacitances directly as if they were in parallel.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    C1=10.0  μF,  C2′=3.00⋅10.0  μF=30.0  μFC_1 = 10.0\;\mu\text{F},\; C_2' = 3.00 \cdot 10.0\;\mu\text{F} = 30.0\;\mu\text{F}

  2. Step 2

    Ceq′=C1+C2′=10.0+30.0=40.0  μFC_{\text{eq}}' = C_1 + C_2' = 10.0 + 30.0 = 40.0\;\mu\text{F}

    Correct

    1Ceq′=1C1+1C2′  ⟹  Ceq′=10.0⋅30.010.0+30.0  μF=7.50  μF\frac{1}{C_{\text{eq}}'} = \frac{1}{C_1} + \frac{1}{C_2'} \implies C_{\text{eq}}' = \frac{10.0 \cdot 30.0}{10.0 + 30.0}\;\mu\text{F} = 7.50\;\mu\text{F}

    Capacitors in series add reciprocally: 1Ceq=1C1+1C2\frac{1}{C_{\text{eq}}} = \frac{1}{C_1} + \frac{1}{C_2}. Adding capacitances directly (C1+C2C_1 + C_2) applies only to parallel configurations.

  3. Step 3

    Q′=Ceq′⋅V=40.0⋅24.0=960  μC  ⟹  V2′=Q′C2′=96030.0=32.0 VQ' = C_{\text{eq}}' \cdot V = 40.0 \cdot 24.0 = 960\;\mu\text{C} \implies V_2' = \frac{Q'}{C_2'} = \frac{960}{30.0} = 32.0\text{ V}

    Correct

    Q′=Ceq′⋅V=(7.50  μF)(24.0 V)=180  μC  ⟹  V2=180  μC30.0  μF=6.00 VQ' = C_{\text{eq}}' \cdot V = (7.50\;\mu\text{F})(24.0\text{ V}) = 180\;\mu\text{C} \implies V_2 = \frac{180\;\mu\text{C}}{30.0\;\mu\text{F}} = 6.00\text{ V}

    Your relations Q′=Ceq′VQ' = C_{\text{eq}}'V and V2=Q′C2′V_2 = \frac{Q'}{C_2'} are conceptually correct, but carrying forward the incorrect equivalent capacitance led to V2=32.0 VV_2 = 32.0\text{ V} (which also exceeds the 24.0 V24.0\text{ V} source voltage).

  4. Step 4

    Ceq, initial=10.0+10.0=20.0  μF  ⟹  Qinitial=20.0⋅24.0=480  μCC_{\text{eq, initial}} = 10.0 + 10.0 = 20.0\;\mu\text{F} \implies Q_{\text{initial}} = 20.0 \cdot 24.0 = 480\;\mu\text{C}

    Correct

    Ceq, initial=C02=5.00  μF  ⟹  Qinitial=(5.00  μF)(24.0 V)=120  μCC_{\text{eq, initial}} = \frac{C_0}{2} = 5.00\;\mu\text{F} \implies Q_{\text{initial}} = (5.00\;\mu\text{F})(24.0\text{ V}) = 120\;\mu\text{C}

    You repeated the parallel addition formula for the initial series combination instead of calculating Ceq, initial=C02=5.00  μFC_{\text{eq, initial}} = \frac{C_0}{2} = 5.00\;\mu\text{F}.

  5. Step 5

    ΔQ1=Q′−Qinitial=960−480=+480  μC\Delta Q_1 = Q' - Q_{\text{initial}} = 960 - 480 = +480\;\mu\text{C}

    Correct

    ΔQ1=Q′−Qinitial=180  μC−120  μC=+60.0  μC\Delta Q_1 = Q' - Q_{\text{initial}} = 180\;\mu\text{C} - 120\;\mu\text{C} = +60.0\;\mu\text{C}

    Your formula for the change in charge is correct, but the result is affected by the earlier equivalent capacitance errors.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly increased the capacitance of C2C_2 by the factor κ=3.00\kappa = 3.00.

You correctly applied Q=CeqVQ = C_{\text{eq}}V to find total circuit charge.

You recognized that series capacitors carry equal charge and defined ΔQ1=Q′−Qinitial\Delta Q_1 = Q' - Q_{\text{initial}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Parallel Addition Used for Series Capacitors

You added capacitances directly (Ceq=C1+C2C_{\text{eq}} = C_1 + C_2) instead of using the reciprocal addition rule for series connections.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You reversed the combination rules for capacitors and resistors. Unlike resistors, capacitors add directly in parallel and reciprocally in series because series plates divide the applied voltage while maintaining a single shared charge.

REASONING PATH
Your ACEpath teacher’s suggested approach
Series vs. Parallel Equivalent Capacitance
  • For series capacitors: 1Ceq=1C1+1C2=C1C2C1+C2\frac{1}{C_{\text{eq}}} = \frac{1}{C_1} + \frac{1}{C_2} = \frac{C_1 C_2}{C_1 + C_2}. For parallel capacitors: Ceq=C1+C2C_{\text{eq}} = C_1 + C_2.

  • Check whether charge must pass sequentially through each capacitor (series →\rightarrow reciprocal sum) or can split between independent branches (parallel →\rightarrow direct sum).

Sanity Check on Series Voltages
  • By Kirchhoff's voltage law, the voltage across any individual passive capacitor in a series loop cannot exceed the total battery voltage: Vi<VtotalV_i < V_{\text{total}}.

  • When you obtained V2=32.0 VV_2 = 32.0\text{ V} across one capacitor from a 24.0 V24.0\text{ V} battery, pause and re-check your equivalent capacitance.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the new series equivalent capacitance: Ceq′=C1⋅C2′C1+C2′=10.0⋅30.010.0+30.0  μF=7.50  μFC_{\text{eq}}' = \frac{C_1 \cdot C_2'}{C_1 + C_2'} = \frac{10.0 \cdot 30.0}{10.0 + 30.0}\;\mu\text{F} = 7.50\;\mu\text{F}.

  2. Find the new series charge: Q′=Ceq′⋅V=(7.50  μF)(24.0 V)=180  μCQ' = C_{\text{eq}}' \cdot V = (7.50\;\mu\text{F})(24.0\text{ V}) = 180\;\mu\text{C}.

  3. Compute the new voltage across C2C_2: V2=Q′C2′=180  μC30.0  μF=6.00 VV_2 = \frac{Q'}{C_2'} = \frac{180\;\mu\text{C}}{30.0\;\mu\text{F}} = 6.00\text{ V}.

  4. Find the initial series equivalent capacitance and charge: Ceq, initial=10.02  μF=5.00  μF  ⟹  Qinitial=(5.00  μF)(24.0 V)=120  μCC_{\text{eq, initial}} = \frac{10.0}{2}\;\mu\text{F} = 5.00\;\mu\text{F} \implies Q_{\text{initial}} = (5.00\;\mu\text{F})(24.0\text{ V}) = 120\;\mu\text{C}.

  5. Calculate the change in charge on C1C_1: ΔQ1=Q′−Qinitial=180  μC−120  μC=+60.0  μC\Delta Q_1 = Q' - Q_{\text{initial}} = 180\;\mu\text{C} - 120\;\mu\text{C} = +60.0\;\mu\text{C}.

Final answer

V2=6.00 VV_2 = 6.00\text{ V}, ΔQ1=+60.0  μF\Delta Q_1 = +60.0\;\mu\text{F}

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the mnemonic: 'Capacitors combine opposite to resistors' (series = reciprocals, parallel = direct sum).

  • Always perform a quick voltage reasonableness check: in series, V1+V2=VbatteryV_1 + V_2 = V_{\text{battery}}, so each component voltage must be less than the total.

OverviewACEpath Teacher's Diagnosis

03 The student assumes the un-modified capacitor's charge remains constant because its physical dimensions and capacitance did not change.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    C1=10.0  μF,  C2′=30.0  μF  ⟹  1Ceq′=110.0+130.0=430.0  ⟹  Ceq′=7.50  μFC_1 = 10.0\;\mu\text{F},\; C_2' = 30.0\;\mu\text{F} \implies \frac{1}{C_{\text{eq}}'} = \frac{1}{10.0} + \frac{1}{30.0} = \frac{4}{30.0} \implies C_{\text{eq}}' = 7.50\;\mu\text{F}

  2. Step 2

    Q′=7.50×24.0=180  μC  ⟹  V2′=18030.0=6.00 VQ' = 7.50 \times 24.0 = 180\;\mu\text{C} \implies V_2' = \frac{180}{30.0} = 6.00\text{ V}

  3. Step 3

    Capacitor C1C_1 is unchanged and its physical structure is unmodified   ⟹  ΔQ1=0  μC\implies \Delta Q_1 = 0\;\mu\text{C}

    Correct

    Q1=Ceq, initialV=120  μC,  Q1′=180  μC  ⟹  ΔQ1=Q1′−Q1=+60.0  μCQ_1 = C_{\text{eq, initial}} V = 120\;\mu\text{C},\; Q_1' = 180\;\mu\text{C} \implies \Delta Q_1 = Q_1' - Q_1 = +60.0\;\mu\text{C}

    Although capacitor C1C_1 was not physically modified, it is connected in series with C2C_2 across a constant-voltage battery. Because the total equivalent capacitance of the branch increased, the battery supplied additional charge to the entire series line, so the charge on C1C_1 increased from 120  μC120\;\mu\text{C} to 180  μC180\;\mu\text{C}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly scaled the capacitance of C2C_2 by the dielectric constant κ\kappa.

You combined series capacitors properly to obtain the new equivalent capacitance Ceq′C_{\text{eq}}'.

You determined the correct final potential difference V2=6.00 VV_2 = 6.00\text{ V}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Local Modification Misconception in Series Circuits

Assuming an un-modified component in a series network maintains a constant electrical state.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the constant physical structure of C1C_1 as implying a constant stored charge, overlooking that in a series circuit connected to a constant voltage source, changing one element alters the equivalent capacitance and therefore changes the charge shared across every component in the branch.

REASONING PATH
Your ACEpath teacher’s suggested approach
Series Charge Invariance
  • Every capacitor in a single series branch carries identical charge equal to Q=CeqVtotalQ = C_{\text{eq}} V_{\text{total}}.

  • Whenever any component in a series circuit changes, recompute CeqC_{\text{eq}} to find the new shared branch charge before comparing it to the initial state.

Local vs. Global Changes
  • An untouched component keeps its capacitance CC, but its voltage and charge adapt to the circuit's new equilibrium.

  • Do not set ΔQ=0\Delta Q = 0 or ΔV=0\Delta V = 0 for an un-modified capacitor unless the circuit topology strictly isolates it or holds its terminal voltage fixed.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the initial charge on C1C_1 before insertion: Ceq, initial=C02=5.00  μFC_{\text{eq, initial}} = \frac{C_0}{2} = 5.00\;\mu\text{F}, so Qinitial=(5.00  μF)(24.0 V)=120  μCQ_{\text{initial}} = (5.00\;\mu\text{F})(24.0\text{ V}) = 120\;\mu\text{C}.

  2. Identify the final charge on C1C_1 from the new series charge: Q1′=Q′=180  μCQ_1' = Q' = 180\;\mu\text{C}.

  3. Compute the change in charge: ΔQ1=Q1′−Qinitial=180  μC−120  μC=+60.0  μC\Delta Q_1 = Q_1' - Q_{\text{initial}} = 180\;\mu\text{C} - 120\;\mu\text{C} = +60.0\;\mu\text{C}.

Final answer

V2=6.00 V,  ΔQ1=+60.0  μCV_2 = 6.00\text{ V},\; \Delta Q_1 = +60.0\;\mu\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always calculate both initial and final states (QinitialQ_{\text{initial}} and QfinalQ_{\text{final}}) explicitly when a problem asks for a change ΔQ\Delta Q.

  • Remember that in series branches, charge is a shared property of the whole loop, so modifying one capacitor redistributes charge across all capacitors in that branch.

Lock it in

Similar question

01

Two capacitors of capacitance CA=4.0  μFC_A = 4.0\;\mu\text{F} and CB=12.0  μFC_B = 12.0\;\mu\text{F} are connected in series across a 48.0 V48.0\text{ V} power supply. Calculate the voltage drop across each capacitor.

Answer

VA=36.0 V,  VB=12.0 VV_A = 36.0\text{ V},\; V_B = 12.0\text{ V}. The equivalent capacitance is Ceq=4.0×12.04.0+12.0=3.0  μFC_{\text{eq}} = \frac{4.0 \times 12.0}{4.0 + 12.0} = 3.0\;\mu\text{F}. The total series charge is Q=(3.0  μF)(48.0 V)=144  μCQ = (3.0\;\mu\text{F})(48.0\text{ V}) = 144\;\mu\text{C}. Then VA=144  μC4.0  μF=36.0 VV_A = \frac{144\;\mu\text{C}}{4.0\;\mu\text{F}} = 36.0\text{ V} and VB=144  μC12.0  μF=12.0 VV_B = \frac{144\;\mu\text{C}}{12.0\;\mu\text{F}} = 12.0\text{ V}.

02

A 20.0  μF20.0\;\mu\text{F} air-filled capacitor and an identical second capacitor are connected in series to a 60.0 V60.0\text{ V} DC source. A dielectric with κ=4.00\kappa = 4.00 is completely inserted into the second capacitor while the battery stays connected. Determine the final voltage across the unmodified capacitor and the modified capacitor.

Answer

V1=48.0 V,  V2=12.0 VV_1 = 48.0\text{ V},\; V_2 = 12.0\text{ V}. The modified capacitance is C2′=4.00×20.0=80.0  μFC_2' = 4.00 \times 20.0 = 80.0\;\mu\text{F}. Using the capacitive voltage divider, V1=60.0×80.020.0+80.0=48.0 VV_1 = 60.0 \times \frac{80.0}{20.0 + 80.0} = 48.0\text{ V} and V2=60.0×20.020.0+80.0=12.0 VV_2 = 60.0 \times \frac{20.0}{20.0 + 80.0} = 12.0\text{ V}.

03

Three capacitors with ratings C1=10  μFC_1 = 10\;\mu\text{F}, C2=20  μFC_2 = 20\;\mu\text{F}, and C3=30  μFC_3 = 30\;\mu\text{F} are connected in series across a 110 V110\text{ V} source. Find the potential difference across C1C_1.

Answer

V1=60 VV_1 = 60\text{ V}. Find equivalent capacitance: 1Ceq=110+120+130=6+3+260=1160  μF−1\frac{1}{C_{\text{eq}}} = \frac{1}{10} + \frac{1}{20} + \frac{1}{30} = \frac{6 + 3 + 2}{60} = \frac{11}{60}\;\mu\text{F}^{-1}, so Ceq=6011  μFC_{\text{eq}} = \frac{60}{11}\;\mu\text{F}. Total charge is Q=CeqV=(6011)(110)=600  μCQ = C_{\text{eq}} V = \left(\frac{60}{11}\right)(110) = 600\;\mu\text{C}. The voltage across C1C_1 is V1=QC1=600  μC10  μF=60 VV_1 = \frac{Q}{C_1} = \frac{600\;\mu\text{C}}{10\;\mu\text{F}} = 60\text{ V}.

Loading workspace…