Resources

An ultra-high-impedance electrometer with internal leakage resistance Rleak=1.50 GΩR_{\text{leak}} = 1.50\text{ G}\Omega is connected across an isolated, charged air-gap parallel-plate capacitor of capacitance C=250 pFC = 250\text{ pF}. The capacitor is initially charged to an initial voltage V0=100.0 VV_0 = 100.0\text{ V} and left in open ambient air. (a) Calculate the asymptotic discharge time constant τ0\tau_0. (b) Determine the time tt required for the voltage across the capacitor plates to drop asymptotically to thermal noise floor levels of Vnoise=1.00 mVV_{\text{noise}} = 1.00\text{ mV}. (c) What is the total electric charge that will have passed through the electrometer leakage resistance between t=0t = 0 and t→∞t \to \infty?

Answer and steps

Final answer

(a) τ0=0.375 s\tau_0 = 0.375\text{ s}; (b) t=4.32 st = 4.32\text{ s}; (c) Qtotal=2.50×10−8 CQ_{\text{total}} = 2.50 \times 10^{-8}\text{ C} (or 25.0 nC25.0\text{ nC})

Steps

Part (a): Calculating the Discharge Time Constant τ0\tau_0

When a capacitor discharges through a resistor, the rate of discharge is characterized by the capacitive time constant τ0\tau_0. By definition, the time constant for an RCRC circuit is:

τ0=RleakC\tau_0 = R_{\text{leak}} C

Convert the given quantities into standard SI units:

  • Resistance: Rleak=1.50 GΩ=1.50×109 ΩR_{\text{leak}} = 1.50\text{ G}\Omega = 1.50 \times 10^9\ \Omega
  • Capacitance: C=250 pF=250×10−12 F=2.50×10−10 FC = 250\text{ pF} = 250 \times 10^{-12}\text{ F} = 2.50 \times 10^{-10}\text{ F}

Substitute these values into the formula:

τ0=(1.50×109 Ω)(2.50×10−10 F)=0.375 s\tau_0 = (1.50 \times 10^9\ \Omega)(2.50 \times 10^{-10}\text{ F}) = 0.375\text{ s}


Part (b): Time Required to Reach the Noise Floor Voltage

The voltage across a discharging capacitor decreases exponentially with time according to the equation:

V(t)=V0e−t/τ0V(t) = V_0 e^{-t/\tau_0}

To find the time tt at which V(t)=Vnoise=1.00 mV=1.00×10−3 VV(t) = V_{\text{noise}} = 1.00\text{ mV} = 1.00 \times 10^{-3}\text{ V}:

  1. Isolate the exponential term: V(t)V0=e−t/τ0\frac{V(t)}{V_0} = e^{-t/\tau_0}
  2. Take the natural logarithm of both sides: ln⁡(V(t)V0)=−tτ0  ⟹  t=τ0ln⁡(V0V(t))\ln\left(\frac{V(t)}{V_0}\right) = -\frac{t}{\tau_0} \implies t = \tau_0 \ln\left(\frac{V_0}{V(t)}\right)
  3. Substitute the numerical values: V0Vnoise=100.0 V1.00×10−3 V=1.00×105\frac{V_0}{V_{\text{noise}}} = \frac{100.0\text{ V}}{1.00 \times 10^{-3}\text{ V}} = 1.00 \times 10^5

    t=(0.375 s)⋅ln⁡(105)=(0.375 s)⋅(5ln⁡10)≈(0.375 s)⋅(11.513)≈4.32 st = (0.375\text{ s}) \cdot \ln(10^5) = (0.375\text{ s}) \cdot (5 \ln 10) \approx (0.375\text{ s}) \cdot (11.513) \approx 4.32\text{ s}

Common Pitfall: Ensure that both voltages are expressed in the same unit (V\text{V}) before computing their ratio. Omitting the prefix conversion for millivolts would lead to an incorrect ratio.


Part (c): Total Charge Passing Through the Leakage Resistance

As t→∞t \to \infty, the capacitor discharges completely from its initial potential V0V_0 down to 0 V0\text{ V}. Therefore, the total charge QtotalQ_{\text{total}} that flows through the electrometer is equal to the total charge initially stored on the capacitor:

Qtotal=Q0=CV0Q_{\text{total}} = Q_0 = C V_0

Substitute the given capacitance and initial voltage:

Qtotal=(250×10−12 F)(100.0 V)=2.50×10−8 C=25.0 nCQ_{\text{total}} = (250 \times 10^{-12}\text{ F})(100.0\text{ V}) = 2.50 \times 10^{-8}\text{ C} = 25.0\text{ nC}

Alternatively, integrating the discharge current I(t)=V0Rleake−t/τ0I(t) = \frac{V_0}{R_{\text{leak}}} e^{-t/\tau_0} from t=0t = 0 to t→∞t \to \infty confirms this result:

∫0∞I(t) dt=V0Rleak[−τ0e−t/τ0]0∞=V0τ0Rleak=CV0=2.50×10−8 C\int_0^{\infty} I(t)\,dt = \frac{V_0}{R_{\text{leak}}} \left[-\tau_0 e^{-t/\tau_0}\right]_0^{\infty} = \frac{V_0 \tau_0}{R_{\text{leak}}} = C V_0 = 2.50 \times 10^{-8}\text{ C}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misinterprets the metric prefix giga (G) as 10⁶ instead of 10⁹, leading to an underestimated time constant and discharge duration.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R=1.50×106 ΩR = 1.50 \times 10^6\,\Omega, C=250×10−12 F  ⟹  τ0=RC=(1.50×106)×(250×10−12)=3.75×10−4 sC = 250 \times 10^{-12}\text{ F} \implies \tau_0 = RC = (1.50 \times 10^6) \times (250 \times 10^{-12}) = 3.75 \times 10^{-4}\text{ s}

    Correct

    τ0=RleakC=(1.50×109 Ω)(250×10−12 F)=0.375 s\tau_0 = R_{\text{leak}} C = (1.50 \times 10^9\,\Omega)(250 \times 10^{-12}\text{ F}) = 0.375\text{ s}

    You correctly set up the time constant formula τ0=RC\tau_0 = RC and handled picofarads (10−1210^{-12}), but giga (G\text{G}) corresponds to 10910^9, not 10610^6 (mega, M\text{M}).

  2. Step 2

    V(t)=V0e−t/τ0  ⟹  t=τ0ln⁡(V0/Vnoise)=(3.75×10−4)×ln⁡(100.0/0.001)=(3.75×10−4)×11.513=4.32×10−3 sV(t) = V_0 e^{-t/\tau_0} \implies t = \tau_0 \ln(V_0 / V_{\text{noise}}) = (3.75 \times 10^{-4}) \times \ln(100.0 / 0.001) = (3.75 \times 10^{-4}) \times 11.513 = 4.32 \times 10^{-3}\text{ s}

    Correct

    t=τ0ln⁡(V0Vnoise)=(0.375 s)ln⁡(100.0 V1.00×10−3 V)=0.375×11.513≈4.32 st = \tau_0 \ln\left(\frac{V_0}{V_{\text{noise}}}\right) = (0.375\text{ s}) \ln\left(\frac{100.0\text{ V}}{1.00 \times 10^{-3}\text{ V}}\right) = 0.375 \times 11.513 \approx 4.32\text{ s}

    Your algebraic derivation and voltage unit conversion (1.00 mV=0.001 V1.00\text{ mV} = 0.001\text{ V}) were completely correct, but your final numerical value was affected by the value of τ0\tau_0 carried over from part (a).

  3. Step 3

    Qtotal=CV0=(250×10−12 F)×100.0 V=2.50×10−8 CQ_{\text{total}} = C V_0 = (250 \times 10^{-12}\text{ F}) \times 100.0\text{ V} = 2.50 \times 10^{-8}\text{ C}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied the time constant equation τ0=RC\tau_0 = RC.

You flawlessly solved the exponential decay equation V(t)=V0e−t/τ0V(t) = V_0 e^{-t/\tau_0} for the elapsed time tt.

You correctly converted 1.00 mV1.00\text{ mV} to 0.001 V0.001\text{ V} when evaluating the voltage ratio.

You recognized that total charge transferred over full discharge is Q0=CV0Q_0 = C V_0 and evaluated it accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric prefix confusion (Giga vs. Mega)

You substituted 10610^6 instead of 10910^9 for the prefix giga (G\text{G}).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the SI prefix giga (G=109\text{G} = 10^9) with mega (M=106\text{M} = 10^6), a common slip when converting large electrical resistance values.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check SI Multiplier Prefixes
  • k=103\text{k} = 10^3, M=106\text{M} = 10^6, G=109\text{G} = 10^9, T=1012\text{T} = 10^{12}

  • Always double-check large multipliers: giga (G\text{G}) is a billion (10910^9), whereas mega (M\text{M}) is a million (10610^6).

Sense-Check RC Time Constants
  • τ=RC\tau = R C

  • Pairing a gigaohm-range leakage resistor (109 Ω10^9\,\Omega) with a sub-nanofarad capacitor (10−10 F10^{-10}\text{ F}) typically produces a time constant on the order of tenths of a second to seconds, not fractions of a millisecond.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert Rleak=1.50 GΩR_{\text{leak}} = 1.50\text{ G}\Omega to standard SI units: 1.50×109 Ω1.50 \times 10^9\,\Omega.

  2. Recalculate the discharge time constant: τ0=(1.50×109 Ω)(2.50×10−10 F)=0.375 s\tau_0 = (1.50 \times 10^9\,\Omega)(2.50 \times 10^{-10}\text{ F}) = 0.375\text{ s}.

  3. Substitute τ0=0.375 s\tau_0 = 0.375\text{ s} into your time equation: t=0.375×11.513≈4.32 st = 0.375 \times 11.513 \approx 4.32\text{ s}.

Final answer

(a) τ0=0.375 s\tau_0 = 0.375\text{ s}; (b) t=4.32 st = 4.32\text{ s}; (c) Qtotal=2.50×10−8 CQ_{\text{total}} = 2.50 \times 10^{-8}\text{ C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the standard SI metric prefix ladder from micro (μ\mu) to giga (G\text{G}) and tera (T\text{T}).

  • Practice converting mixed-prefix circuit values (e.g., GΩ\text{G}\Omega, MΩ\text{M}\Omega, pF\text{pF}, nF\text{nF}) into scientific notation before substituting them into formulas.

OverviewACEpath Teacher's Diagnosis

02 The student uses the common logarithm (log₁₀) instead of the natural logarithm (ln) when inverting the exponential decay equation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ0=Rleak×C  ⟹  τ0=(1.50×109 Ω)×(250×10−12 F)  ⟹  τ0=0.375 s\tau_0 = R_{\text{leak}} \times C \implies \tau_0 = (1.50 \times 10^9\ \Omega) \times (250 \times 10^{-12}\text{ F}) \implies \tau_0 = 0.375\text{ s}

  2. Step 2

    V(t)=V0e−t/τ0  ⟹  t=τ0log⁡10(V0/Vnoise)  ⟹  t=0.375×log⁡10(100.0/1.00×10−3)  ⟹  t=0.375×5  ⟹  t=1.88 sV(t) = V_0 e^{-t/\tau_0} \implies t = \tau_0 \log_{10}(V_0/V_{\text{noise}}) \implies t = 0.375 \times \log_{10}(100.0 / 1.00 \times 10^{-3}) \implies t = 0.375 \times 5 \implies t = 1.88\text{ s}

    Correct

    t=τ0ln⁡(V0Vnoise)=(0.375 s)⋅ln⁡(105)≈(0.375 s)(11.513)≈4.32 st = \tau_0 \ln\left(\frac{V_0}{V_{\text{noise}}}\right) = (0.375\text{ s}) \cdot \ln(10^5) \approx (0.375\text{ s})(11.513) \approx 4.32\text{ s}

    Because the voltage decay involves Euler's constant ee, the inverse function is the natural logarithm ln⁡\ln, not the base-10 logarithm log⁡10\log_{10}. Using log⁡10\log_{10} misses a factor of ln⁡(10)≈2.303\ln(10) \approx 2.303.

  3. Step 3

    Qtotal=CV0  ⟹  Qtotal=(250×10−12 F)×100.0 V  ⟹  Qtotal=2.50×10−8 CQ_{\text{total}} = C V_0 \implies Q_{\text{total}} = (250 \times 10^{-12}\text{ F}) \times 100.0\text{ V} \implies Q_{\text{total}} = 2.50 \times 10^{-8}\text{ C}

WHAT YOU DID WELL
Compliments from Your Teacher

You applied the correct time-constant formula τ0=RC\tau_0 = RC with precise unit conversions.

You identified the governing exponential discharge equation V(t)=V0e−t/τ0V(t) = V_0 e^{-t/\tau_0}.

You correctly related the total discharged charge to the initial capacitor charge Q0=CV0Q_0 = C V_0.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Logarithm Base Confusion

You wrote log⁡10\log_{10} instead of ln⁡\ln when undoing the natural exponential e−t/τ0e^{-t/\tau_0}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Inverting natural exponential decay requires the natural logarithm ($ \ln x = \log_e x)because) because \ln(e^u) = u,whereas, whereas \log_{10}(e^u) = u \log_{10}(e) ≈\approx 0.4343 u.Confusing. Confusing \log_{10}withwith\lnscalestheresultingtimedownbyafactorofscales the resulting time down by a factor of\ln(10) ≈\approx 2.303$._

REASONING PATH
Your ACEpath teacher’s suggested approach
Match the Logarithm Base to the Exponential Base
  • If an equation has the form ex=ye^x = y, take the natural logarithm: ln⁡(ex)=ln⁡(y)  ⟹  x=ln⁡(y)\ln(e^x) = \ln(y) \implies x = \ln(y).

  • Reserve log⁡10\log_{10} strictly for powers of 10, such as decibels or pH scales, and use ln⁡\ln whenever dealing with RCRC or RLRL circuits governed by e−t/τe^{-t/\tau}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Divide both sides by V0V_0: V(t)V0=e−t/τ0\frac{V(t)}{V_0} = e^{-t/\tau_0}.

  2. Take the natural logarithm of both sides: ln⁡(V(t)V0)=−tau0\ln\left(\frac{V(t)}{V_0}\right) = -\frac{t}{ au_0}.

  3. Solve for tt: t = \tau_0 \ln\left(\frac{V_0}{V(t)} ight).

  4. Substitute the voltage values and time constant: t=(0.375 s)⋅ln⁡(100.0 V1.00×10−3 V)=(0.375 s)⋅ln⁡(105)t = (0.375\text{ s}) \cdot \ln\left(\frac{100.0\text{ V}}{1.00 \times 10^{-3}\text{ V}}\right) = (0.375\text{ s}) \cdot \ln(10^5).

  5. Evaluate using ln⁡(105)=5ln⁡(10)≈11.513\ln(10^5) = 5 \ln(10) \approx 11.513: t≈0.375×11.513≈4.32 st \approx 0.375 \times 11.513 \approx 4.32\text{ s}.

Final answer

(a) τ0=0.375 s\tau_0 = 0.375\text{ s}; (b) t=4.32 st = 4.32\text{ s}; (c) Qtotal=2.50×10−8 CQ_{\text{total}} = 2.50 \times 10^{-8}\text{ C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the inverse relationship between exe^x and ln⁡(x)\ln(x) on your formula sheet.

  • Practice solving exponential decay equations by isolating e−t/τe^{-t/\tau} and explicitly writing ln⁡\ln on both sides.

  • Check that your final numerical answer for discharge time is longer than a few time constants when the voltage drops by multiple orders of magnitude.

OverviewACEpath Teacher's Diagnosis

03 The student confuses total charge transferred with steady-state current, multiplying Ohm's law current by the time constant instead of evaluating the initial capacitor charge.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    τ0=Rleak×C  ⟹  τ0=(1.50×109 Ω)×(250×10−12 F)  ⟹  τ0=0.375 s\tau_0 = R_{\text{leak}} \times C \implies \tau_0 = (1.50 \times 10^9\ \Omega) \times (250 \times 10^{-12}\ \text{F}) \implies \tau_0 = 0.375\ \text{s}

  2. Step 2

    V(t)=V0e−t/τ0  ⟹  t=τ0ln⁡(V0/Vnoise)  ⟹  t=0.375×ln⁡(100.0/0.00100)  ⟹  t=0.375×11.51  ⟹  t=4.32 sV(t) = V_0 e^{-t/\tau_0} \implies t = \tau_0 \ln(V_0 / V_{\text{noise}}) \implies t = 0.375 \times \ln(100.0 / 0.00100) \implies t = 0.375 \times 11.51 \implies t = 4.32\ \text{s}

  3. Step 3

    I0=V0Rleak=100.0(1.50×109)=6.67×10−8 A  ⟹  Qtotal=I0×τ0=(6.67×10−8 A)×0.375 s  ⟹  Qtotal=2.50×10−8 CI_0 = \frac{V_0}{R_{\text{leak}}} = \frac{100.0}{(1.50 \times 10^9)} = 6.67 \times 10^{-8}\ \text{A} \implies Q_{\text{total}} = I_0 \times \tau_0 = (6.67 \times 10^{-8}\ \text{A}) \times 0.375\ \text{s} \implies Q_{\text{total}} = 2.50 \times 10^{-8}\ \text{C}

    Correct

    Qtotal=Q0=CV0=(250×10−12 F)(100.0 V)=2.50×10−8 CQ_{\text{total}} = Q_0 = C V_0 = (250 \times 10^{-12}\ \text{F})(100.0\ \text{V}) = 2.50 \times 10^{-8}\ \text{C}

    You applied Q=I0×τ0Q = I_0 \times \tau_0 as if the initial current remained constant for a duration of one time constant. The discharge current decays exponentially, so you cannot apply constant-current formulas. The total charge transferred as t→∞t \to \infty is simply the initial stored charge Q0=CV0Q_0 = C V_0.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the circuit discharge time constant τ0=RleakC\tau_0 = R_{\text{leak}} C.

You modeled exponential voltage decay accurately to determine the time to reach the noise floor.

You handled all metric prefixes correctly, including gigaohms, picofarads, and millivolts.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Misapplying steady current formula to exponential discharge

You computed the initial current and multiplied it by the time constant (Q=I0τ0Q = I_0 \tau_0) rather than directly evaluating the capacitor's stored charge Q0=CV0Q_0 = C V_0.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the discharge process as a steady-state current flowing over a time interval equal to τ0\tau_0. Because current decays continuously according to I(t)=I0e−t/τ0I(t) = I_0 e^{-t/\tau_0}, the total charge transferred to infinity equals the initial charge on the plates (Qtotal=CV0Q_{\text{total}} = C V_0), which also matches the integral ∫0∞I(t) dt\int_0^\infty I(t)\,dt.

REASONING PATH
Your ACEpath teacher’s suggested approach
Total Transferred Charge in Complete Discharge
  • When a capacitor completely discharges to 0 V0\ \text{V}, all charge initially stored on its plates flows through the discharge path: Qtotal=Q0=CV0Q_{\text{total}} = Q_0 = C V_0.

  • Calculate the total charge directly from the capacitor relation Q=CV0Q = C V_0 without introducing intermediate currents.

Validity of $Q = I \Delta t$
  • The formula Q=IΔtQ = I \Delta t requires current II to be constant over the entire duration Δt\Delta t.

  • For time-varying currents, determine transferred charge either by integrating Q=∫I(t) dtQ = \int I(t)\,dt or by using initial and final stored charges.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recognize that as t→∞t \to \infty, the capacitor discharges completely from initial potential V0=100.0 VV_0 = 100.0\ \text{V} down to 0 V0\ \text{V}.

  2. Apply the fundamental definition of stored capacitance charge: Qtotal=Q0=CV0Q_{\text{total}} = Q_0 = C V_0.

  3. Substitute the given capacitance and voltage values: Qtotal=(250×10−12 F)(100.0 V)=2.50×10−8 CQ_{\text{total}} = (250 \times 10^{-12}\ \text{F})(100.0\ \text{V}) = 2.50 \times 10^{-8}\ \text{C} (or 25.0 nC25.0\ \text{nC}).

Final answer

Qtotal=2.50×10−8 CQ_{\text{total}} = 2.50 \times 10^{-8}\ \text{C} (or 25.0 nC25.0\ \text{nC})

NEXT STEPS
Final Takeaways from Your Teacher
  • Use conservation of charge (Qtotal=CV0Q_{\text{total}} = C V_0) when finding the total charge transferred during a complete discharge.

  • Review the integration of exponential decay ∫0∞I0e−t/τ dt=I0τ\int_0^\infty I_0 e^{-t/\tau}\,dt = I_0 \tau to see why your numerical product yielded the correct number despite the conceptual slip.

Lock it in

Similar question

01

A high-precision ionization chamber has an insulation leakage resistance of 4.00 GΩ4.00\text{ G}\Omega in parallel with an internal capacitance of 120 pF120\text{ pF}. Calculate the leakage time constant τ\tau.

Answer

τ=RC=(4.00×109 Ω)(120×10−12 F)=0.480 s\tau = RC = (4.00 \times 10^9\,\Omega)(120 \times 10^{-12}\text{ F}) = 0.480\text{ s}.

02

A 50.0 pF50.0\text{ pF} capacitor charged to 50.0 V50.0\text{ V} discharges through an electrometer of input resistance 2.00 GΩ2.00\text{ G}\Omega. How long does it take for the capacitor voltage to drop to 5.00 V5.00\text{ V}?

Answer

t=τln⁡(V0/V)=(2.00×109×50.0×10−12)ln⁡(50.0/5.00)=(0.100 s)ln⁡(10)≈0.230 st = \tau \ln(V_0 / V) = (2.00 \times 10^9 \times 50.0 \times 10^{-12}) \ln(50.0 / 5.00) = (0.100\text{ s}) \ln(10) \approx 0.230\text{ s}.

03

An electrostatic voltmeter with resistance R=5.00 GΩR = 5.00\text{ G}\Omega is connected across a charged capacitor C=800 pFC = 800\text{ pF}. The initial voltage is 200 V200\text{ V}. (a) Determine the initial stored energy. (b) Find the total energy dissipated in the resistance as t→∞t \to \infty. (c) Find the time required for 99%99\% of the initial energy to be dissipated.

Answer

(a) U0=12CV02=12(800×10−12)(200)2=1.60×10−5 J=16.0 μJU_0 = \frac{1}{2} C V_0^2 = \frac{1}{2}(800 \times 10^{-12})(200)^2 = 1.60 \times 10^{-5}\text{ J} = 16.0\,\mu\text{J}. (b) By conservation of energy, Udiss=U0=16.0 μJU_{\text{diss}} = U_0 = 16.0\,\mu\text{J}. (c) Since U(t)∝V(t)2=V02e−2t/τU(t) \propto V(t)^2 = V_0^2 e^{-2t/\tau}, 1%1\% energy remaining means e−2t/τ=0.01  ⟹  t=τ2ln⁡(100)=τln⁡(10)e^{-2t/\tau} = 0.01 \implies t = \frac{\tau}{2} \ln(100) = \tau \ln(10). With τ=(5.00×109)(800×10−12)=4.00 s\tau = (5.00 \times 10^9)(800 \times 10^{-12}) = 4.00\text{ s}, t=4.00×2.3026≈9.21 st = 4.00 \times 2.3026 \approx 9.21\text{ s}.

Loading workspace…