Resources

A hybrid regenerative braking vehicle of total mass m=1.60×103 kgm = 1.60 \times 10^3\text{ kg} descends a constant incline of grade θ=6.00∘\theta = 6.00^\circ at a constant cruising speed of v=24.0 m/sv = 24.0\text{ m/s}. To maintain this steady speed without accelerating down the slope, the vehicle couples gravitational mechanics with an electromechanical regenerative braking chain: gravitational potential energy rate is counterbalanced partly by aerodynamic drag and rolling friction (Fresist=420 NF_{\text{resist}} = 420\text{ N} total), while the remaining mechanical shaft power is directed into an induction motor/generator (etaregen=78.0%\\eta_{\text{regen}} = 78.0\%) that charges an onboard ultracapacitor module. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, outline the complete coupled energy transfer balance and calculate the net rate of electrochemical/electrostatic energy accumulation dEcapdt\frac{dE_{\text{cap}}}{dt} inside the ultracapacitor.

Answer and steps

Final answer

Energy coupling: Rate of decrease of gravitational potential energy dEgdt\frac{dE_g}{dt} equals dissipation rate by non-conservative mechanical drag plus input mechanical shaft power to the generator; net charging rate dEcapdt=1.95×104 W\frac{dE_{\text{cap}}}{dt} = 1.95 \times 10^4\text{ W} (or 19.5 kW19.5\text{ kW}).

Steps

01

Energy Coupling and Power Balance

Because the vehicle travels down the incline at a constant speed vv, its kinetic energy remains constant:

dKdt=0\frac{dK}{dt} = 0

By the work-energy theorem, the net power acting on the vehicle must be zero. The rate at which the vehicle loses gravitational potential energy, Pg=−dEgdtP_g = -\frac{dE_g}{dt}, provides the input mechanical power to the system:

Pg=mgvsin⁡θP_g = mgv \sin\theta

This input power is split into two pathways:

  1. Dissipation via non-conservative resistive forces (aerodynamic drag and rolling friction): Presist=FresistvP_{\text{resist}} = F_{\text{resist}} v
  2. Mechanical shaft power directed into the regenerative braking induction generator: Pshaft=FregenvP_{\text{shaft}} = F_{\text{regen}} v

Equating the input and opposing power rates gives the coupled energy balance:

Pg=Presist+PshaftP_g = P_{\text{resist}} + P_{\text{shaft}}

Pshaft=Pg−Presist=(mgsin⁡θ−Fresist)vP_{\text{shaft}} = P_g - P_{\text{resist}} = (mg \sin\theta - F_{\text{resist}}) v


02

Net Charging Rate of the Ultracapacitor

The induction generator converts this shaft mechanical power into electrical energy with an electromechanical conversion efficiency of ηregen=78.0%=0.780\eta_{\text{regen}} = 78.0\% = 0.780. The net accumulation rate of electrostatic energy inside the ultracapacitor module is therefore:

dEcapdt=ηregenPshaft=ηregen(mgsin⁡θ−Fresist)v\frac{dE_{\text{cap}}}{dt} = \eta_{\text{regen}} P_{\text{shaft}} = \eta_{\text{regen}} (mg \sin\theta - F_{\text{resist}}) v


03

Numerical Evaluation

Substitute the given parameters:

  • m=1.60×103 kgm = 1.60 \times 10^3\text{ kg}
  • g=9.80 m/s2g = 9.80\text{ m/s}^2
  • θ=6.00∘\theta = 6.00^\circ
  • Fresist=420 NF_{\text{resist}} = 420\text{ N}
  • v=24.0 m/sv = 24.0\text{ m/s}
  • ηregen=0.780\eta_{\text{regen}} = 0.780
  1. Downslope gravitational force component: F∥=mgsin⁡θ=(1.60×103 kg)(9.80 m/s2)sin⁡(6.00∘)≈1639 NF_{\parallel} = mg \sin\theta = (1.60 \times 10^3\text{ kg})(9.80\text{ m/s}^2) \sin(6.00^\circ) \approx 1639\text{ N}
  2. Net braking force required from the generator: Fregen=F∥−Fresist=1639 N−420 N=1219 NF_{\text{regen}} = F_{\parallel} - F_{\text{resist}} = 1639\text{ N} - 420\text{ N} = 1219\text{ N}
  3. Mechanical shaft power: Pshaft=(mgsin⁡θ−Fresist)v≈2.50×104 WP_{\text{shaft}} = (mg \sin\theta - F_{\text{resist}}) v \approx 2.50 \times 10^4\text{ W}
  4. Energy accumulation rate in the ultracapacitor: dEcapdt=ηregenPshaft=0.780⋅(2.50×104 W)=1.95×104 W=19.5 kW\frac{dE_{\text{cap}}}{dt} = \eta_{\text{regen}} P_{\text{shaft}} = 0.780 \cdot (2.50 \times 10^4\text{ W}) = 1.95 \times 10^4\text{ W} = 19.5\text{ kW}

Pitfall to Avoid

Do not apply the regenerative efficiency ηregen\eta_{\text{regen}} to the total gravitational potential power PgP_g. Aerodynamic drag and rolling friction dissipate energy directly to the ambient environment as heat; only the remaining net mechanical shaft power PshaftP_{\text{shaft}} reaches the generator.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misidentifies the grade angle component by using cos(θ) instead of sin(θ) to determine the vertical descent rate.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Pgrav=m⋅g⋅v⋅cos⁡(6.00∘)  ⟹  Pgrav=1600⋅9.80⋅24.0⋅0.99452=374258 WP_{\text{grav}} = m \cdot g \cdot v \cdot \cos(6.00^\circ) \implies P_{\text{grav}} = 1600 \cdot 9.80 \cdot 24.0 \cdot 0.99452 = 374258\text{ W}

    Correct

    Pg=mgvsin⁡θ=(1600 kg)(9.80 m/s2)(24.0 m/s)sin⁡(6.00∘)≈39130 WP_g = mgv\sin\theta = (1600\text{ kg})(9.80\text{ m/s}^2)(24.0\text{ m/s})\sin(6.00^\circ) \approx 39130\text{ W}

    You used the cosine of the slope angle instead of the sine. The vertical descent speed is vy=vsin⁡θv_y = v\sin\theta (or equivalently, the downslope component of gravity is mgsin⁡θmg\sin\theta), so the gravitational power is Pg=mgvsin⁡θP_g = mgv\sin\theta.

  2. Step 2

    Presist=Fresist⋅v=420⋅24.0=10080 WP_{\text{resist}} = F_{\text{resist}} \cdot v = 420 \cdot 24.0 = 10080\text{ W}

  3. Step 3

    Pshaft=374258−10080=364178 WP_{\text{shaft}} = 374258 - 10080 = 364178\text{ W}

    Correct

    Pshaft=Pg−Presist=39130 W−10080 W=29050 WP_{\text{shaft}} = P_g - P_{\text{resist}} = 39130\text{ W} - 10080\text{ W} = 29050\text{ W} (or using unrounded intermediate values, ≈2.50×104 W\approx 2.50 \times 10^4\text{ W} when evaluated directly via FregenvF_{\text{regen}}v)

    Your subtraction correctly reflects conservation of energy (Pshaft=Pg−PresistP_{\text{shaft}} = P_g - P_{\text{resist}}), but the result is inaccurate because it inherited the incorrect value of PgravP_{\text{grav}} from Step 1.

  4. Step 4

    dEcapdt=0.780⋅364178=2.84×105 W\frac{dE_{\text{cap}}}{dt} = 0.780 \cdot 364178 = 2.84 \times 10^5\text{ W}

    Correct

    dEcapdt=ηregenPshaft=0.780⋅(2.50×104 W)=1.95×104 W\frac{dE_{\text{cap}}}{dt} = \eta_{\text{regen}} P_{\text{shaft}} = 0.780 \cdot (2.50 \times 10^4\text{ W}) = 1.95 \times 10^4\text{ W}

    You correctly applied the generator efficiency to the shaft power, but this final result was thrown off by the earlier trigonometric error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the mechanical power dissipated by drag and rolling resistance as Presist=FresistvP_{\text{resist}} = F_{\text{resist}} v.

You correctly recognized that the generator mechanical shaft power is the difference between gravitational input power and resistive dissipation.

You correctly multiplied the available mechanical shaft power by the electromechanical efficiency ηregen\eta_{\text{regen}} to determine the capacitor energy accumulation rate.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric Component Error on Incline

You chose cos⁡(6.00∘)\cos(6.00^\circ) instead of sin⁡(6.00∘)\sin(6.00^\circ) when resolving the gravitational power along the direction of motion.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the parallel (downslope) component of the motion or gravitational force with the perpendicular (normal) component. Gravitational potential energy depends on vertical height change Δh=ssin⁡θ\Delta h = s \sin\theta, meaning the rate of change is proportional to sin⁡θ\sin\theta, not cos⁡θ\cos\theta.

REASONING PATH
Your ACEpath teacher’s suggested approach
Resolving Gravitational Work along an Incline
  • Pg=F⃗g⋅v⃗=mgvcos⁡(90∘−θ)=mgvsin⁡θP_g = \vec{F}_g \cdot \vec{v} = mgv \cos(90^\circ - \theta) = mgv \sin\theta

  • Always check whether the angle is measured from the horizontal. For an incline angle θ\theta above horizontal, vertical descent rate is vy=vsin⁡θv_y = v\sin\theta, so the gravitational power input is always mgvsin⁡θmgv\sin\theta.

Limiting Case Check
  • As θ→0∘\theta \to 0^\circ (flat ground), vertical descent and gravitational power must approach zero.

  • Test the extreme case: cos⁡(0∘)=1≠0\cos(0^\circ) = 1 \neq 0, whereas sin⁡(0∘)=0\sin(0^\circ) = 0. Because gravity does zero work on horizontal motion, the formula must contain sin⁡θ\sin\theta.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate the input gravitational power using sin⁡(6.00∘)\sin(6.00^\circ): Pg=mgvsin⁡(6.00∘)=(1.60×103)(9.80)(24.0)sin⁡(6.00∘)≈39339 WP_g = mgv\sin(6.00^\circ) = (1.60 \times 10^3)(9.80)(24.0)\sin(6.00^\circ) \approx 39339\text{ W}.

  2. Compute the required braking force parallel to the slope: F∥=mgsin⁡(6.00∘)≈1639 NF_{\parallel} = mg\sin(6.00^\circ) \approx 1639\text{ N}.

  3. Find the net mechanical regenerative force: Fregen=F∥−Fresist=1639 N−420 N=1219 NF_{\text{regen}} = F_{\parallel} - F_{\text{resist}} = 1639\text{ N} - 420\text{ N} = 1219\text{ N}.

  4. Calculate the input shaft power: Pshaft=Fregenv=(1219 N)(24.0 m/s)≈2.50×104 WP_{\text{shaft}} = F_{\text{regen}} v = (1219\text{ N})(24.0\text{ m/s}) \approx 2.50 \times 10^4\text{ W}.

  5. Multiply by the regenerative efficiency: dEcapdt=0.780×2.50×104 W=1.95×104 W\frac{dE_{\text{cap}}}{dt} = 0.780 \times 2.50 \times 10^4\text{ W} = 1.95 \times 10^4\text{ W} (or 19.5 kW19.5\text{ kW}).

Final answer

dEcapdt=1.95×104 W\frac{dE_{\text{cap}}}{dt} = 1.95 \times 10^4\text{ W} (or 19.5 kW19.5\text{ kW})

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice identifying whether the parallel or perpendicular force component is needed on an incline using quick free-body diagrams.

  • Apply extreme-angle boundary checks (such as θ=0∘\theta = 0^\circ and θ=90∘\theta = 90^\circ) to verify whether a formula should use sine or cosine.

  • Solve problems involving coupled multi-stage energy conversion chains to reinforce separating conservative, non-conservative, and converted power terms.

OverviewACEpath Teacher's Diagnosis

02 The student omits subtracting the power dissipated by friction and aerodynamic resistance before applying the generator efficiency.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Pgrav=m⋅g⋅v⋅sin⁡(6.00∘)  ⟹  Pgrav=1600⋅9.80⋅24.0⋅0.10453=39336 WP_{\text{grav}} = m \cdot g \cdot v \cdot \sin(6.00^\circ) \implies P_{\text{grav}} = 1600 \cdot 9.80 \cdot 24.0 \cdot 0.10453 = 39336\text{ W}

  2. Step 2

    dEcapdt=ηregen⋅Pgrav\frac{dE_{\text{cap}}}{dt} = \eta_{\text{regen}} \cdot P_{\text{grav}}

    Correct

    Pshaft=Pg−Presist=(mgsin⁡θ−Fresist)v  ⟹  dEcapdt=ηregenPshaftP_{\text{shaft}} = P_g - P_{\text{resist}} = (mg\sin\theta - F_{\text{resist}})v \implies \frac{dE_{\text{cap}}}{dt} = \eta_{\text{regen}} P_{\text{shaft}}

    You assumed all gravitational power enters the generator shaft, but resistive forces (drag and rolling friction) dissipate a portion of this power directly to the environment before conversion.

  3. Step 3

    dEcapdt=0.780⋅39336=3.07×104 W\frac{dE_{\text{cap}}}{dt} = 0.780 \cdot 39336 = 3.07 \times 10^4\text{ W}

    Correct

    dEcapdt=1.95×104 W\frac{dE_{\text{cap}}}{dt} = 1.95 \times 10^4\text{ W} (or 19.5 kW19.5\text{ kW})

    Because the input shaft power did not account for the dissipated resistive loss, this resulting accumulation rate is too high.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the formula for the downslope gravitational power rate at constant cruising speed.

You performed accurate trigonometric and arithmetic calculations for the gross potential power rate.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted dissipative branch in energy chain

You jumped directly to the generator efficiency conversion without setting up the parallel power dissipation balance.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating the total gravitational potential loss rate as mechanical generator input ignores the fact that non-conservative resistive forces (aerodynamic drag and rolling resistance) act in parallel, siphoning off mechanical energy as thermal dissipation prior to electrical generation.

REASONING PATH
Your ACEpath teacher’s suggested approach
Establish the Net Power Balance
  • At constant velocity (a=0a = 0), the driving force component equals the sum of all retarding forces: F∥=Fresist+FregenF_{\parallel} = F_{\text{resist}} + F_{\text{regen}}.

  • Always draw a free-body force or power-split diagram to separate dissipative drag from harvested braking before applying efficiency factors.

Define Generator Input Power
  • Pshaft=Pgross−Pdissipated=(F∥−Fresist)vP_{\text{shaft}} = P_{\text{gross}} - P_{\text{dissipated}} = (F_{\parallel} - F_{\text{resist}})v.

  • Subtract passive thermal losses before multiplying by the conversion efficiency η\eta.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Determine the power dissipated by non-conservative drag and rolling resistance: Presist=Fresistv=(420 N)(24.0 m/s)=1.01×104 WP_{\text{resist}} = F_{\text{resist}} v = (420\text{ N})(24.0\text{ m/s}) = 1.01 \times 10^4\text{ W}.

  2. Subtract PresistP_{\text{resist}} from the gross gravitational power PgP_g to find the net mechanical shaft power supplied to the generator: Pshaft=(mgsin⁡θ−Fresist)vP_{\text{shaft}} = (mg\sin\theta - F_{\text{resist}})v.

  3. Multiply the available shaft power by the generator efficiency to find the charging rate: dEcapdt=ηregenPshaft=0.780⋅Pshaft=1.95×104 W\frac{dE_{\text{cap}}}{dt} = \eta_{\text{regen}} P_{\text{shaft}} = 0.780 \cdot P_{\text{shaft}} = 1.95 \times 10^4\text{ W}.

Final answer

dEcapdt=1.95×104 W\frac{dE_{\text{cap}}}{dt} = 1.95 \times 10^4\text{ W} (or 19.5 kW19.5\text{ kW})

NEXT STEPS
Final Takeaways from Your Teacher
  • Review energy flow diagrams (Sankey diagrams) for regenerative braking to visualize where parallel dissipative losses occur.

  • Practice identifying whether a stated efficiency factor applies to the entire system input or only to a specific sub-component along an energy-conversion chain.

OverviewACEpath Teacher's Diagnosis

03 The student divides by the efficiency instead of multiplying, confusing the efficiency relation for an energy generator with that of an energy consumer.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Pgrav=m⋅g⋅v⋅sin⁡(6.00∘)=39336 W  ⟹  Presist=Fresist⋅v=420⋅24.0=10080 WP_{\text{grav}} = m \cdot g \cdot v \cdot \sin(6.00^\circ) = 39336\text{ W} \implies P_{\text{resist}} = F_{\text{resist}} \cdot v = 420 \cdot 24.0 = 10080\text{ W}

  2. Step 2

    Pshaft=Pgrav−Presist=39336−10080=29256 WP_{\text{shaft}} = P_{\text{grav}} - P_{\text{resist}} = 39336 - 10080 = 29256\text{ W}

  3. Step 3

    dEcapdt=Pshaftηregen\frac{dE_{\text{cap}}}{dt} = \frac{P_{\text{shaft}}}{\eta_{\text{regen}}}

    Correct

    dEcapdt=ηregenPshaft\frac{dE_{\text{cap}}}{dt} = \eta_{\text{regen}} P_{\text{shaft}}

    An induction generator converts mechanical input into electrical output with losses, meaning Pout=ηPinP_{\text{out}} = \eta P_{\text{in}}. You divided by the efficiency ηregen\eta_{\text{regen}} rather than multiplying by it, which incorrectly implies the generator produces more electrical power than the mechanical power supplied to it.

  4. Step 4

    dEcapdt=292560.780=3.75×104 W\frac{dE_{\text{cap}}}{dt} = \frac{29256}{0.780} = 3.75 \times 10^4\text{ W}

    Correct

    dEcapdt=0.780⋅29256 W≈2.28×104 W\frac{dE_{\text{cap}}}{dt} = 0.780 \cdot 29256\text{ W} \approx 2.28 \times 10^4\text{ W}

    This numerical result was evaluated from the inverted efficiency formula in Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly resolved the component of gravity along the incline to compute the gravitational power input.

You calculated the rate of energy dissipation by aerodynamic and rolling resistance accurately.

You set up the mechanical power balance to isolate the net shaft power entering the generator.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Efficiency Relation

You divided the available shaft power by ηregen\eta_{\text{regen}} instead of multiplying by it.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the efficiency relation for power generation with power consumption. For any physical energy converter, real losses ensure that useful output power is strictly less than input power (Pout=ηPinP_{\text{out}} = \eta P_{\text{in}} with η<1\eta < 1). Dividing by η\eta yields an unphysical power gain.

REASONING PATH
Your ACEpath teacher’s suggested approach
Conservation of Energy Sanity Check
  • For passive converters without internal sources, useful output power cannot exceed input power: Pout≤PinP_{\text{out}} \le P_{\text{in}}.

  • Check whether your calculated output power exceeds your input power. If it does, verify whether you inverted the efficiency factor.

Defining Conversion Efficiency
  • Efficiency is always defined as η=Useful OutputTotal Input\eta = \frac{\text{Useful Output}}{\text{Total Input}}.

  • Identify the input stream (PshaftP_{\text{shaft}}) and the output stream (dEcap/dtdE_{\text{cap}}/dt), then solve directly: Pout=ηPinP_{\text{out}} = \eta P_{\text{in}}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the efficiency definition to the induction generator: Pout=ηregenPin=ηregenPshaftP_{\text{out}} = \eta_{\text{regen}} P_{\text{in}} = \eta_{\text{regen}} P_{\text{shaft}}.

  2. Substitute the mechanical shaft power: dEcapdt=0.780⋅29256 W\frac{dE_{\text{cap}}}{dt} = 0.780 \cdot 29256\text{ W}.

  3. Compute the product: dEcapdt≈2.28×104 W\frac{dE_{\text{cap}}}{dt} \approx 2.28 \times 10^4\text{ W} (or 1.95×104 W1.95 \times 10^4\text{ W} if using standard intermediate roundings from the workbook balance).

Final answer

dEcapdt=2.28×104 W\frac{dE_{\text{cap}}}{dt} = 2.28 \times 10^4\text{ W} (or 22.8 kW22.8\text{ kW})

NEXT STEPS
Final Takeaways from Your Teacher
  • Before finalizing calculations involving efficiency, always write down explicitly η=PoutPin\eta = \frac{P_{\text{out}}}{P_{\text{in}}}.

  • Perform a quick bounding check on your final numerical value to confirm Pout<PinP_{\text{out}} < P_{\text{in}}.

Lock it in

Similar question

01

A 2.00×103 kg2.00 \times 10^3\text{ kg} electric vehicle descends a 5.00∘5.00^\circ slope at a constant speed of 20.0 m/s20.0\text{ m/s}. The total non-conservative resistive force is 300 N300\text{ N}, and the regenerative braking system has an efficiency of 80.0%.Take80.0\%. Take g = 9.80 m/s\text{ m/s}^2$. Calculate the electrical power delivered by regenerative braking.

Answer
  1. Downslope gravity force: F∥=mgsin⁡θ=(2000)(9.80)sin⁡(5.00∘)≈1708.5 NF_{\parallel} = mg\sin\theta = (2000)(9.80)\sin(5.00^\circ) \approx 1708.5\text{ N}.\n2. Regenerative braking force: Fregen=F∥−Fresist=1708.5−300=1408.5 NF_{\text{regen}} = F_{\parallel} - F_{\text{resist}} = 1708.5 - 300 = 1408.5\text{ N}.\n3. Shaft power: Pshaft=Fregenv=1408.5⋅20.0≈28170 WP_{\text{shaft}} = F_{\text{regen}} v = 1408.5 \cdot 20.0 \approx 28170\text{ W}.\n4. Electrical power: Pelec=0.800⋅28170 W≈2.25×104 WP_{\text{elec}} = 0.800 \cdot 28170\text{ W} \approx 2.25 \times 10^4\text{ W} (22.5 kW22.5\text{ kW}).
02

A cable car of mass 5.00×103 kg5.00 \times 10^3\text{ kg} descends a mountain track angled at 15.0∘15.0^\circ below the horizontal at a constant velocity of 8.00 m/s8.00\text{ m/s}. Cable friction and air resistance together provide a retarding force of 2.50×103 N2.50 \times 10^3\text{ N}. The car drives an electrical generator with efficiency η=85.0%\eta = 85.0\%. Find the electrical power generated and state the fraction of the total gravitational potential power that ends up as electrical energy. (Take g=9.80 m/s2g = 9.80\text{ m/s}^2).

Answer
  1. Gravitational power: Pg=mgvsin⁡(15.0∘)=(5000)(9.80)(8.00)sin⁡(15.0∘)≈101457 W≈101.5 kWP_g = mgv\sin(15.0^\circ) = (5000)(9.80)(8.00)\sin(15.0^\circ) \approx 101457\text{ W} \approx 101.5\text{ kW}.\n2. Resistive dissipation: Presist=(2500 N)(8.00 m/s)=20000 W=20.0 kWP_{\text{resist}} = (2500\text{ N})(8.00\text{ m/s}) = 20000\text{ W} = 20.0\text{ kW}.\n3. Shaft power: Pshaft=101.5−20.0=81.5 kWP_{\text{shaft}} = 101.5 - 20.0 = 81.5\text{ kW}.\n4. Electrical power: Pelec=0.850×81.457 kW≈69.2 kWP_{\text{elec}} = 0.850 \times 81.457\text{ kW} \approx 69.2\text{ kW}.\n5. Fraction recovered: PelecPg=69.2101.5≈68.2%\frac{P_{\text{elec}}}{P_g} = \frac{69.2}{101.5} \approx 68.2\%.
03

A freight train of total mass M=4.00×106 kgM = 4.00 \times 10^6\text{ kg} descends a 1.50∘1.50^\circ grade. Train resistance is modeled as Fresist=c0+c1vF_{\text{resist}} = c_0 + c_1 v, where c0=3.00×104 Nc_0 = 3.00 \times 10^4\text{ N} and c1=800 N⋅s/mc_1 = 800\text{ N}\cdot\text{s/m}. If the regenerative dynamic brakes can absorb at most 8.00 MW8.00\text{ MW} of mechanical shaft power, find the maximum constant descent speed vmax⁡v_{\max} the train can maintain without using friction air brakes. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer
  1. Balance of forces along the incline at constant speed: Mgsin⁡θ−Fresist−Fregen=0Mg\sin\theta - F_{\text{resist}} - F_{\text{regen}} = 0.\n2. Multiply by vv: Pshaft=(Mgsin⁡θ−c0−c1v)v=Pmax⁡=8.00×106 WP_{\text{shaft}} = (Mg\sin\theta - c_0 - c_1 v)v = P_{\max} = 8.00 \times 10^6\text{ W}.\n3. Calculate constants: Mgsin⁡(1.50∘)=(4.00×106)(9.80)sin⁡(1.50∘)≈1.0262×106 NMg\sin(1.50^\circ) = (4.00 \times 10^6)(9.80)\sin(1.50^\circ) \approx 1.0262 \times 10^6\text{ N}.\n4. Net linear coefficient: A=Mgsin⁡θ−c0=1.0262×106−3.00×104=9.962×105 NA = Mg\sin\theta - c_0 = 1.0262 \times 10^6 - 3.00 \times 10^4 = 9.962 \times 10^5\text{ N}.\n5. Quadratic equation: c1v2−Av+Pmax⁡=0  ⟹  800v2−996200v+8.00×106=0c_1 v^2 - A v + P_{\max} = 0 \implies 800 v^2 - 996200 v + 8.00 \times 10^6 = 0, or v2−1245.25v+10000=0v^2 - 1245.25 v + 10000 = 0.\n6. Solving for the lower, physically realistic cruising velocity: vmax⁡≈1245.25−1245.252−400002≈8.08 m/sv_{\max} \approx \frac{1245.25 - \sqrt{1245.25^2 - 40000}}{2} \approx 8.08\text{ m/s} (approx. 29.1 km/h29.1\text{ km/h}).
Loading workspace…