Resources

An electric heating element supplies a constant thermal power of P=750 WP = 750\text{ W} to an insulated copper vessel containing 0.500 kg0.500\text{ kg} of liquid water at 20.0∘C20.0^\circ\text{C}. The mass of the copper vessel is 0.200 kg0.200\text{ kg} (cCu=387 J/(kg⋅∘C)c_{\text{Cu}} = 387\text{ J}/(\text{kg}\cdot^\circ\text{C})), and the specific heat of water is cw=4186 J/(kg⋅∘C)c_{\text{w}} = 4186\text{ J}/(\text{kg}\cdot^\circ\text{C}). Determine the exact heating duration Δtboil\Delta t_{\text{boil}} required to bring the water up to its boiling threshold of 100.0∘C100.0^\circ\text{C}, and calculate the maximum additional time Δtevap\Delta t_{\text{evap}} that the heater can run past this threshold before exactly 10.0%10.0\% of the water mass is vaporized. Take the latent heat of vaporization of water at 100.0∘C100.0^\circ\text{C} as Lv=2.26×106 J/kgL_v = 2.26 \times 10^6\text{ J}/\text{kg}.

Answer and steps

Final answer

Δtboil=232 s\Delta t_{\text{boil}} = 232\text{ s}, Δtevap=151 s\Delta t_{\text{evap}} = 151\text{ s}

Steps

01

Identify the heat required to reach the boiling point

Both the water and the copper vessel are in thermal equilibrium and are heated together from an initial temperature of Ti=20.0∘CT_i = 20.0^\circ\text{C} to the boiling temperature Tf=100.0∘CT_f = 100.0^\circ\text{C}.

The temperature change for both components is: ΔT=Tf−Ti=100.0∘C−20.0∘C=80.0∘C\Delta T = T_f - T_i = 100.0^\circ\text{C} - 20.0^\circ\text{C} = 80.0^\circ\text{C}

The total heat energy QboilQ_{\text{boil}} needed to warm both substances is given by the sum of their heat capacities multiplied by ΔT\Delta T: Qboil=(mwcw+mCucCu)ΔTQ_{\text{boil}} = (m_{\text{w}} c_{\text{w}} + m_{\text{Cu}} c_{\text{Cu}}) \Delta T

Substitute the given values: mwcw=(0.500 kg)(4186 J/(kg⋅∘C))=2093 J/∘Cm_{\text{w}} c_{\text{w}} = (0.500\text{ kg})(4186\text{ J}/(\text{kg}\cdot^\circ\text{C})) = 2093\text{ J}/^\circ\text{C} mCucCu=(0.200 kg)(387 J/(kg⋅∘C))=77.4 J/∘Cm_{\text{Cu}} c_{\text{Cu}} = (0.200\text{ kg})(387\text{ J}/(\text{kg}\cdot^\circ\text{C})) = 77.4\text{ J}/^\circ\text{C}

Qboil=(2093 J/∘C+77.4 J/∘C)⋅80.0∘C=(2170.4 J/∘C)⋅80.0∘C=173632 JQ_{\text{boil}} = (2093\text{ J}/^\circ\text{C} + 77.4\text{ J}/^\circ\text{C}) \cdot 80.0^\circ\text{C} = (2170.4\text{ J}/^\circ\text{C}) \cdot 80.0^\circ\text{C} = 173632\text{ J}

Common Pitfall: Forgetting to include the thermal energy absorbed by the container (mCucCuΔTm_{\text{Cu}} c_{\text{Cu}} \Delta T) leads to underestimating the time required to reach the boiling threshold.


02

Calculate the time to reach the boiling threshold (Δtboil\Delta t_{\text{boil}})

Since the electric heater provides a constant power P=750 WP = 750\text{ W}, the energy supplied over time Δt\Delta t is Q=P⋅ΔtQ = P \cdot \Delta t. Rearranging for the duration: Δtboil=QboilP=173632 J750 W≈231.51 s\Delta t_{\text{boil}} = \frac{Q_{\text{boil}}}{P} = \frac{173632\text{ J}}{750\text{ W}} \approx 231.51\text{ s}

Rounding to three significant figures: Δtboil=232 s\Delta t_{\text{boil}} = 232\text{ s}


03

Calculate the heat required to vaporize 10.0%10.0\% of the water

Once the system reaches 100.0∘C100.0^\circ\text{C}, the temperature remains constant during phase change. Any additional heat is used exclusively for vaporization.

The mass of water vaporized is: mvap=0.100⋅mw=0.100⋅0.500 kg=0.0500 kgm_{\text{vap}} = 0.100 \cdot m_{\text{w}} = 0.100 \cdot 0.500\text{ kg} = 0.0500\text{ kg}

The heat required for this phase change is: Qevap=mvapLv=(0.0500 kg)(2.26×106 J/kg)=113000 JQ_{\text{evap}} = m_{\text{vap}} L_v = (0.0500\text{ kg})(2.26 \times 10^6\text{ J}/\text{kg}) = 113000\text{ J}


04

Calculate the additional time needed (Δtevap\Delta t_{\text{evap}})

Using the constant thermal power of the heater: Δtevap=QevapP=113000 J750 W≈150.67 s\Delta t_{\text{evap}} = \frac{Q_{\text{evap}}}{P} = \frac{113000\text{ J}}{750\text{ W}} \approx 150.67\text{ s}

Rounding to three significant figures: Δtevap=151 s\Delta t_{\text{evap}} = 151\text{ s}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student ignores the heat capacity of the copper container and only calculates the energy absorbed by the water when heating to boiling.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ΔT=100.0−20.0=80.0∘C\Delta T = 100.0 - 20.0 = 80.0^\circ\text{C}

  2. Step 2

    Qheat=mw∗cw∗ΔT=0.500∗4186∗80.0=167440 JQ_{\text{heat}} = m_{\text{w}} * c_{\text{w}} * \Delta T = 0.500 * 4186 * 80.0 = 167440\text{ J}

    Correct

    Qboil=(mwcw+mCucCu)ΔT=(2093 J/∘C+77.4 J/∘C)⋅80.0∘C=173632 JQ_{\text{boil}} = (m_{\text{w}} c_{\text{w}} + m_{\text{Cu}} c_{\text{Cu}}) \Delta T = (2093\text{ J}/^\circ\text{C} + 77.4\text{ J}/^\circ\text{C}) \cdot 80.0^\circ\text{C} = 173632\text{ J}

    You only calculated the heat absorbed by the water. Because the water is inside an insulated copper container, the copper container also warms up by 80.0∘C80.0^\circ\text{C} and absorbs an additional QCu=mCucCuΔT=77.4⋅80.0=6192 JQ_{\text{Cu}} = m_{\text{Cu}} c_{\text{Cu}} \Delta T = 77.4 \cdot 80.0 = 6192\text{ J}.

  3. Step 3

    Δtboil=223.25 s\Delta t_{\text{boil}} = 223.25\text{ s}

    Correct

    Δtboil=QboilP=173632 J750 W≈232 s\Delta t_{\text{boil}} = \frac{Q_{\text{boil}}}{P} = \frac{173632\text{ J}}{750\text{ W}} \approx 232\text{ s}

    Your calculation 167440 J750 W≈223.25 s\frac{167440\text{ J}}{750\text{ W}} \approx 223.25\text{ s} followed correctly from your previous value, but it is numerically low due to omitting the vessel's heat capacity.

  4. Step 4

    mevap=0.100∗0.500=0.0500 kg  ⟹  Qevap=mevap∗Lv=0.0500∗2.26∗106=113000 Jm_{\text{evap}} = 0.100 * 0.500 = 0.0500\text{ kg} \implies Q_{\text{evap}} = m_{\text{evap}} * L_v = 0.0500 * 2.26 * 10^6 = 113000\text{ J}

  5. Step 5

    Δtevap=113000/750=150.67 s\Delta t_{\text{evap}} = 113000 / 750 = 150.67\text{ s}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the temperature difference ΔT=80.0∘C\Delta T = 80.0^\circ\text{C}.

You correctly applied the latent heat equation Q=mLvQ = m L_v for the 10.0%10.0\% phase change.

You accurately related total energy to duration using Δt=QP\Delta t = \frac{Q}{P}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted Container Heat Capacity

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You neglected the heat capacity of the container holding the liquid. In calorimetry and heating problems, any vessel in thermal contact with the liquid undergoes the same temperature change and absorbs part of the supplied thermal energy.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify all bodies undergoing temperature change
  • When a fluid is heated inside a vessel, both the fluid and the vessel remain in thermal equilibrium: Qtotal=(m1c1+m2c2+… )ΔTQ_{\text{total}} = (m_1 c_1 + m_2 c_2 + \dots)\Delta T.

  • Always list every component in the system and check whether its mass and specific heat are provided in the problem statement.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the heat absorbed by the copper vessel: QCu=mCucCuΔT=(0.200 kg)(387 J/(kg⋅∘C))(80.0∘C)=6192 JQ_{\text{Cu}} = m_{\text{Cu}} c_{\text{Cu}} \Delta T = (0.200\text{ kg})(387\text{ J}/(\text{kg}\cdot^\circ\text{C}))(80.0^\circ\text{C}) = 6192\text{ J}.

  2. Add this to the heat absorbed by the water: Qboil=Qw+QCu=167440 J+6192 J=173632 JQ_{\text{boil}} = Q_{\text{w}} + Q_{\text{Cu}} = 167440\text{ J} + 6192\text{ J} = 173632\text{ J}.

  3. Calculate the corrected time to boil: Δtboil=173632 J750 W≈231.51 s≈232 s\Delta t_{\text{boil}} = \frac{173632\text{ J}}{750\text{ W}} \approx 231.51\text{ s} \approx 232\text{ s}.

Final answer

Δtboil=232 s\Delta t_{\text{boil}} = 232\text{ s}, Δtevap=151 s\Delta t_{\text{evap}} = 151\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always reread the problem statement to ensure every given property (like mCum_{\text{Cu}} and cCuc_{\text{Cu}}) is accounted for in your energy balance.

  • Note that during phase change at constant temperature, the vessel does not absorb additional sensible heat, which is why your calculation for Δtevap\Delta t_{\text{evap}} was completely correct.

OverviewACEpath Teacher's Diagnosis

02 The student mistakenly vaporizes the entire mass of water rather than only 10.0% of it.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ΔT=100.0−20.0=80.0∘C  ⟹  Qheat=(0.500×4186+0.200×387)×80.0=173632 J\Delta T = 100.0 - 20.0 = 80.0^\circ\text{C} \implies Q_{\text{heat}} = (0.500 \times 4186 + 0.200 \times 387) \times 80.0 = 173632\text{ J}

  2. Step 2

    Δtboil=173632/750=231.51 s\Delta t_{\text{boil}} = 173632 / 750 = 231.51\text{ s}

  3. Step 3

    Qevap=mw×Lv=0.500×2.26×106=1130000 JQ_{\text{evap}} = m_{\text{w}} \times L_v = 0.500 \times 2.26 \times 10^6 = 1130000\text{ J}

    Correct

    Qevap=mvapLv=(0.100×0.500 kg)(2.26×106 J/kg)=113000 JQ_{\text{evap}} = m_{\text{vap}} L_v = (0.100 \times 0.500\text{ kg})(2.26 \times 10^6\text{ J}/\text{kg}) = 113000\text{ J}

    You substituted the entire mass of water (0.500 kg0.500\text{ kg}) instead of vaporizing only 10.0%10.0\% of it (mvap=0.0500 kgm_{\text{vap}} = 0.0500\text{ kg}).

  4. Step 4

    Δtevap=1130000/750=1506.67 s\Delta t_{\text{evap}} = 1130000 / 750 = 1506.67\text{ s}

    Correct

    Δtevap=113000 J750 W≈151 s\Delta t_{\text{evap}} = \frac{113000\text{ J}}{750\text{ W}} \approx 151\text{ s}

    Your division by P=750 WP = 750\text{ W} was carried out correctly, but the resulting time was ten times too large due to the incorrect energy value from Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You included both the water and the copper vessel when calculating sensible heat.

You correctly related heating time to heat energy using P=Q/ΔtP = Q / \Delta t.

You selected the correct latent heat equation Q=mLvQ = m L_v for the phase change.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Full Mass Used for Fractional Vaporization

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the phase change as vaporizing all the water present rather than identifying and using the partial mass fraction specified in the problem (10.0%10.0\% of the water mass).

REASONING PATH
Your ACEpath teacher’s suggested approach
Differentiate total mass from transformed mass
  • For partial phase changes, Q=mtransformedLQ = m_{\text{transformed}} L, where mtransformed=f×mtotalm_{\text{transformed}} = f \times m_{\text{total}}.

  • Always explicitly define and compute mvap=f⋅mtotalm_{\text{vap}} = f \cdot m_{\text{total}} as an independent quantity before inserting it into Q=mLQ = m L.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the mass of water converted to steam: mvap=0.100×0.500 kg=0.0500 kgm_{\text{vap}} = 0.100 \times 0.500\text{ kg} = 0.0500\text{ kg}.

  2. Calculate the latent heat required to boil off this mass: Qevap=mvapLv=0.0500 kg×2.26×106 J/kg=113000 JQ_{\text{evap}} = m_{\text{vap}} L_v = 0.0500\text{ kg} \times 2.26 \times 10^6\text{ J}/\text{kg} = 113000\text{ J}.

  3. Calculate the heating duration: Δtevap=113000 J750 W≈150.67 s≈151 s\Delta t_{\text{evap}} = \frac{113000\text{ J}}{750\text{ W}} \approx 150.67\text{ s} \approx 151\text{ s}.

Final answer

Δtboil=232 s\Delta t_{\text{boil}} = 232\text{ s}, Δtevap=151 s\Delta t_{\text{evap}} = 151\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Whenever a problem asks for a percentage or fraction of a substance to change phase, write out mphase=(fraction)×mtotalm_{\text{phase}} = (\text{fraction}) \times m_{\text{total}} before writing the energy equation.

  • Practice thermal problems involving partial phase transitions to avoid defaulting to full substance conversion.

OverviewACEpath Teacher's Diagnosis

03 The student uses the total time from the start of heating instead of the additional time past the boiling threshold for the second task.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ΔT=100.0−20.0=80.0∘C  ⟹  Qheat=(0.500⋅4186+0.200⋅387)⋅80.0=173632 J  ⟹  Δtboil=173632/750=231.51 s\Delta T = 100.0 - 20.0 = 80.0^\circ\text{C} \implies Q_{\text{heat}} = (0.500 \cdot 4186 + 0.200 \cdot 387) \cdot 80.0 = 173632\text{ J} \implies \Delta t_{\text{boil}} = 173632 / 750 = 231.51\text{ s}

  2. Step 2

    mevap=0.100⋅0.500=0.0500 kg  ⟹  Qevap=0.0500⋅2.26×106=113000 Jm_{\text{evap}} = 0.100 \cdot 0.500 = 0.0500\text{ kg} \implies Q_{\text{evap}} = 0.0500 \cdot 2.26 \times 10^6 = 113000\text{ J}

  3. Step 3

    Δttotal=(173632+113000)/750=382.18 s  ⟹  Δtevap=382.18 s\Delta t_{\text{total}} = (173632 + 113000) / 750 = 382.18\text{ s} \implies \Delta t_{\text{evap}} = 382.18\text{ s}

    Correct

    Δtevap=QevapP=113000 J750 W≈151 s\Delta t_{\text{evap}} = \frac{Q_{\text{evap}}}{P} = \frac{113000\text{ J}}{750\text{ W}} \approx 151\text{ s}

    You calculated the total cumulative heating time from the start (t=0t = 0) rather than the additional heating interval Δtevap\Delta t_{\text{evap}} after the boiling point is reached.

WHAT YOU DID WELL
Compliments from Your Teacher

You included the heat capacity of both the copper vessel and the water when calculating the energy needed to warm the system.

You used the correct latent heat equation Q=mLvQ = m L_v for the phase change calculation.

You correctly used the power relation P=QΔtP = \frac{Q}{\Delta t} across all calculations.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Cumulative Time vs. Incremental Time Interval

You solved for the cumulative total time Δttotal\Delta t_{\text{total}} from the very beginning of heating instead of the incremental interval Δtevap\Delta t_{\text{evap}} beyond the boiling point.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Misinterpreting the reference zero-point in multi-stage heating problems by confusing total elapsed time (ttotal=t1+t2t_{\text{total}} = t_1 + t_2) with an isolated stage duration (t2t_2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Define the Time Interval Reference
  • When a prompt asks for 'additional time past [event]' or 'extra time', calculate only the energy added during that specific phase: Δt=QstageP\Delta t = \frac{Q_{\text{stage}}}{P}.

  • Check whether the question asks for 'total time from start' or 'additional time'. If it asks for additional time, use only the energy delivered during that second stage.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Divide only the vaporization energy QevapQ_{\text{evap}} by the constant power P=750 WP = 750\text{ W}:

  2. Δtevap=113000 J750 W≈150.67 s\Delta t_{\text{evap}} = \frac{113000\text{ J}}{750\text{ W}} \approx 150.67\text{ s}

  3. Round to three significant figures to match the given data.

Final answer

Δtboil=232 s\Delta t_{\text{boil}} = 232\text{ s}, Δtevap=151 s\Delta t_{\text{evap}} = 151\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Pay special attention to words like 'additional', 'further', or 'total' in multi-phase physics questions.

  • Draw a simple timeline or energy bar chart separating each stage before converting energy into time.

Lock it in

Similar question

01

An aluminum cup of mass 0.150 kg0.150\text{ kg} (cAl=900 J/(kg⋅∘C)c_{\text{Al}} = 900\text{ J}/(\text{kg}\cdot^\circ\text{C})) contains 0.300 kg0.300\text{ kg} of water (cw=4186 J/(kg⋅∘C)c_{\text{w}} = 4186\text{ J}/(\text{kg}\cdot^\circ\text{C})) at 25.0∘C25.0^\circ\text{C}. An immersion heater supplies 500 W500\text{ W} of power. How long does it take to heat the water and cup to 100.0∘C100.0^\circ\text{C}?

Answer

Q=(mAlcAl+mwcw)ΔT=(0.150×900+0.300×4186)(75.0)=(135+1255.8)(75.0)=104310 JQ = (m_{\text{Al}}c_{\text{Al}} + m_{\text{w}}c_{\text{w}})\Delta T = (0.150 \times 900 + 0.300 \times 4186)(75.0) = (135 + 1255.8)(75.0) = 104310\text{ J}. Then Δt=QP=104310 J500 W≈209 s\Delta t = \frac{Q}{P} = \frac{104310\text{ J}}{500\text{ W}} \approx 209\text{ s}.

02

A 0.250 kg0.250\text{ kg} glass beaker (cglass=840 J/(kg⋅∘C)c_{\text{glass}} = 840\text{ J}/(\text{kg}\cdot^\circ\text{C})) holding 0.400 kg0.400\text{ kg} of ethyl alcohol (ceth=2440 J/(kg⋅∘C)c_{\text{eth}} = 2440\text{ J}/(\text{kg}\cdot^\circ\text{C})) is heated from 18.0∘C18.0^\circ\text{C} to its boiling point of 78.0∘C78.0^\circ\text{C} using a 400 W400\text{ W} hot plate. Find the time needed to reach boiling, and the additional time to vaporize 20.0 g20.0\text{ g} of alcohol (Lv=8.55×105 J/kgL_v = 8.55 \times 10^5\text{ J}/\text{kg}).

Answer
  1. ΔT=60.0∘C\Delta T = 60.0^\circ\text{C}. Qboil=(0.250×840+0.400×2440)(60.0)=(210+976)(60.0)=71160 JQ_{\text{boil}} = (0.250 \times 840 + 0.400 \times 2440)(60.0) = (210 + 976)(60.0) = 71160\text{ J}. Δtboil=71160400=178 s\Delta t_{\text{boil}} = \frac{71160}{400} = 178\text{ s}. 2) Qevap=0.0200×8.55×105=17100 JQ_{\text{evap}} = 0.0200 \times 8.55 \times 10^5 = 17100\text{ J}. Δtevap=17100400=42.8 s\Delta t_{\text{evap}} = \frac{17100}{400} = 42.8\text{ s}.
03

A heating element with power P=1200 WP = 1200\text{ W} warms an iron kettle of mass 1.20 kg1.20\text{ kg} (cFe=450 J/(kg⋅∘C)c_{\text{Fe}} = 450\text{ J}/(\text{kg}\cdot^\circ\text{C})) containing 1.50 kg1.50\text{ kg} of water from 15.0∘C15.0^\circ\text{C} to 100.0∘C100.0^\circ\text{C}, after which it runs for another 300 s300\text{ s}. Assuming no heat is lost to the surroundings, find the total time to reach boiling and the mass of water vaporized during the additional 300 s300\text{ s} (Lv=2.26×106 J/kgL_v = 2.26 \times 10^6\text{ J}/\text{kg}).

Answer
  1. ΔT=85.0∘C\Delta T = 85.0^\circ\text{C}. Qboil=(1.20×450+1.50×4186)(85.0)=(540+6279)(85.0)=579615 JQ_{\text{boil}} = (1.20 \times 450 + 1.50 \times 4186)(85.0) = (540 + 6279)(85.0) = 579615\text{ J}. Δtboil=5796151200≈483 s\Delta t_{\text{boil}} = \frac{579615}{1200} \approx 483\text{ s}. 2) During boiling, Q=P⋅Δt=1200×300=360000 JQ = P \cdot \Delta t = 1200 \times 300 = 360000\text{ J}. Mass vaporized: mvap=QLv=3600002.26×106≈0.159 kgm_{\text{vap}} = \frac{Q}{L_v} = \frac{360000}{2.26 \times 10^6} \approx 0.159\text{ kg}.
Loading workspace…