Resources

A crate of mass m=120 kgm = 120\text{ kg} is released from rest at the top of a frictionless incline of height h=4.90 mh = 4.90\text{ m} inclined at θ=30.0∘\theta = 30.0^\circ above the horizontal. At the base of the ramp, the crate transitions smoothly to a level, horizontal floor where it immediately collides with a safety buffer. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2: (a) Calculate the speed v0v_0 of the crate when it reaches the bottom of the ramp. (b) If the safety buffer consists of a hydraulic piston that brings the crate to rest over a time interval of Δt=0.600 s\Delta t = 0.600\text{ s}, calculate the magnitude of the average horizontal force Fˉbuffer\bar{F}_{\text{buffer}} applied to the crate. (c) If instead of the buffer, the crate slid across a rough horizontal concrete floor having a kinetic friction coefficient μk=0.250\mu_k = 0.250 to come to rest, calculate the time Δtfriction\Delta t_{\text{friction}} required for friction alone to halt the crate.

Answer and steps

Final answer

(a) v0=9.80 m/sv_0 = 9.80\text{ m/s}, (b) Fˉbuffer=1.96×103 N\bar{F}_{\text{buffer}} = 1.96 \times 10^3\text{ N}, (c) Δtfriction=4.00 s\Delta t_{\text{friction}} = 4.00\text{ s}

Steps

Part (a): Determining the Speed at the Bottom of the Ramp

Because the incline is frictionless and transitions smoothly to the horizontal surface, mechanical energy is conserved during the descent:

Einitial=EfinalE_{\text{initial}} = E_{\text{final}}

Setting the gravitational potential energy to zero at the level floor (y=0y = 0):

mgh=12mv02mgh = \frac{1}{2}mv_0^2

Dividing both sides by the mass mm and solving for the speed v0v_0:

v0=2ghv_0 = \sqrt{2gh}

Substitute the given values (g=9.80 m/s2g = 9.80\text{ m/s}^2 and h=4.90 mh = 4.90\text{ m}):

v0=2⋅9.80 m/s2⋅4.90 m=96.04 m2/s2=9.80 m/sv_0 = \sqrt{2 \cdot 9.80\text{ m/s}^2 \cdot 4.90\text{ m}} = \sqrt{96.04\text{ m}^2/\text{s}^2} = 9.80\text{ m/s}

Common Pitfall: The ramp angle θ=30.0∘\theta = 30.0^\circ is extra information; the vertical displacement hh determines the potential energy change regardless of the ramp angle or length.


Part (b): Average Force Exerted by the Safety Buffer

By the impulse-momentum theorem, the net impulse delivered to the crate equals its change in momentum:

J=Δp=mvf−mv0J = \Delta p = m v_f - m v_0

Since the crate comes to rest, vf=0 m/sv_f = 0\text{ m/s}:

Δp=0−(120 kg)(9.80 m/s)=−1176 kg⋅m/s\Delta p = 0 - (120\text{ kg})(9.80\text{ m/s}) = -1176\text{ kg}\cdot\text{m/s}

The average horizontal stopping force exerted by the buffer over the time interval Δt=0.600 s\Delta t = 0.600\text{ s} is:

Fˉbuffer=∣Δp∣Δt=1176 N⋅s0.600 s=1960 N=1.96×103 N\bar{F}_{\text{buffer}} = \frac{|\Delta p|}{\Delta t} = \frac{1176\text{ N}\cdot\text{s}}{0.600\text{ s}} = 1960\text{ N} = 1.96 \times 10^3\text{ N}


Part (c): Stopping Time due to Kinetic Friction

On a flat horizontal surface, the normal force equals the crate's weight: FN=mgF_N = mg. The magnitude of the kinetic friction force is:

fk=μkFN=μkmgf_k = \mu_k F_N = \mu_k mg

Using the impulse-momentum theorem for this scenario:

fkΔtfriction=mv0f_k \Delta t_{\text{friction}} = m v_0

Substituting fk=μkmgf_k = \mu_k mg:

μkmgΔtfriction=mv0\mu_k mg \Delta t_{\text{friction}} = m v_0

Canceling mass mm and solving for the time interval:

Δtfriction=v0μkg\Delta t_{\text{friction}} = \frac{v_0}{\mu_k g}

Substitute the numerical values:

Δtfriction=9.80 m/s0.250⋅9.80 m/s2=10.250 s=4.00 s\Delta t_{\text{friction}} = \frac{9.80\text{ m/s}}{0.250 \cdot 9.80\text{ m/s}^2} = \frac{1}{0.250}\text{ s} = 4.00\text{ s}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student mistakenly multiplies height by sin(θ) when applying conservation of energy, believing height must be projected by the ramp angle.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    mghsin⁡(30.0∘)=12mv02  ⟹  v0=2ghsin⁡(30.0∘)=2×9.80×4.90×0.500=6.93 m/smgh\sin(30.0^\circ) = \frac{1}{2}mv_0^2 \implies v_0 = \sqrt{2gh\sin(30.0^\circ)} = \sqrt{2 \times 9.80 \times 4.90 \times 0.500} = 6.93\text{ m/s}

    Correct

    mgh=12mv02  ⟹  v0=2gh=2(9.80 m/s2)(4.90 m)=9.80 m/smgh = \frac{1}{2}mv_0^2 \implies v_0 = \sqrt{2gh} = \sqrt{2(9.80\text{ m/s}^2)(4.90\text{ m})} = 9.80\text{ m/s}

    You multiplied the given height hh by sin⁡(30.0∘)\sin(30.0^\circ). The problem specifies that h=4.90 mh = 4.90\text{ m} is already the vertical height of the incline, so the change in gravitational potential energy is simply mghmgh. You only multiply by sin⁡θ\sin\theta when you are given the distance along the incline (LL) rather than the vertical height.

  2. Step 2

    Fˉbuffer=mv0Δt=120×6.930.600=1386 N\bar{F}_{\text{buffer}} = \frac{mv_0}{\Delta t} = \frac{120 \times 6.93}{0.600} = 1386\text{ N}

    Correct

    Fˉbuffer=mv0Δt=(120 kg)(9.80 m/s)0.600 s=1.96×103 N\bar{F}_{\text{buffer}} = \frac{mv_0}{\Delta t} = \frac{(120\text{ kg})(9.80\text{ m/s})}{0.600\text{ s}} = 1.96 \times 10^3\text{ N}

    You applied the impulse-momentum theorem correctly to find the average stopping force, but your result was affected by the incorrect value of v0v_0 from part (a).

  3. Step 3

    a=μkg=0.250×9.80=2.45 m/s2  ⟹  Δtfriction=v0a=6.932.45=2.83 sa = \mu_k g = 0.250 \times 9.80 = 2.45\text{ m/s}^2 \implies \Delta t_{\text{friction}} = \frac{v_0}{a} = \frac{6.93}{2.45} = 2.83\text{ s}

    Correct

    a=μkg=2.45 m/s2  ⟹  Δtfriction=v0a=9.80 m/s2.45 m/s2=4.00 sa = \mu_k g = 2.45\text{ m/s}^2 \implies \Delta t_{\text{friction}} = \frac{v_0}{a} = \frac{9.80\text{ m/s}}{2.45\text{ m/s}^2} = 4.00\text{ s}

    You correctly determined the frictional deceleration and kinematic stopping time, but this step inherited the erroneous initial velocity from part (a).

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that mechanical energy is conserved along the frictionless ramp.

You correctly used the impulse-momentum theorem FˉΔt=mv0\bar{F} \Delta t = m v_0 to solve for the buffer's average force.

You accurately derived the acceleration due to kinetic friction on a level surface as a=μkga = \mu_k g.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unnecessary trigonometric projection of vertical height

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the vertical height of an incline with the distance along the slope. Gravitational potential energy depends strictly on the vertical elevation change Δy=h\Delta y = h. The angle θ\theta is only needed if you must resolve a distance along the incline into a vertical drop via h=Lsin⁡θh = L \sin\theta.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check What the Given Length Represents
  • Gravitational potential energy near Earth's surface is Ug=mgyU_g = mgy, where yy is strictly the vertical coordinate.

  • Before writing an energy equation, ask yourself: 'Is the given value the vertical drop hh or the ramp length LL?' If it is already vertical height, use mghmgh directly.

Evaluate If the Angle Is Extraneous
  • In frictionless gravity-driven descent, the final speed depends only on the vertical drop Δy\Delta y, independent of the path slope or incline angle.

  • Remember that v=2ghv = \sqrt{2gh} applies to any frictionless ramp of height hh; the angle only determines acceleration along the ramp and time of descent, not final speed.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set initial gravitational potential energy equal to final kinetic energy: mgh=12mv02mgh = \frac{1}{2}mv_0^2.

  2. Cancel mass mm and solve for v0v_0: v0=2gh=2(9.80)(4.90)=9.80 m/sv_0 = \sqrt{2gh} = \sqrt{2(9.80)(4.90)} = 9.80\text{ m/s}.

  3. Recalculate the buffer force in part (b): Fˉbuffer=mv0Δt=(120)(9.80)0.600=1960 N\bar{F}_{\text{buffer}} = \frac{m v_0}{\Delta t} = \frac{(120)(9.80)}{0.600} = 1960\text{ N}.

  4. Recalculate the stopping time in part (c): Δtfriction=v0μkg=9.80(0.250)(9.80)=4.00 s\Delta t_{\text{friction}} = \frac{v_0}{\mu_k g} = \frac{9.80}{(0.250)(9.80)} = 4.00\text{ s}.

Final answer

(a) v0=9.80 m/sv_0 = 9.80\text{ m/s}, (b) Fˉbuffer=1.96×103 N\bar{F}_{\text{buffer}} = 1.96 \times 10^3\text{ N}, (c) Δtfriction=4.00 s\Delta t_{\text{friction}} = 4.00\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between vertical height hh and incline distance LL when calculating gravitational potential energy.

  • Practice identifying when problem statements provide extraneous geometric information, such as ramp angles in energy conservation problems.

OverviewACEpath Teacher's Diagnosis

02 The student erroneously includes cos(θ) in the normal force on the level horizontal floor by carrying over the ramp incline angle.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    mgh=12mv02  ⟹  v0=2gh=2×9.80×4.90=9.80 m/smgh = \frac{1}{2}mv_0^2 \implies v_0 = \sqrt{2gh} = \sqrt{2 \times 9.80 \times 4.90} = 9.80\text{ m/s}

  2. Step 2

    Favg=mv0Δt  ⟹  Favg=120×9.800.600=1960 NF_{\text{avg}} = \frac{mv_0}{\Delta t} \implies F_{\text{avg}} = \frac{120 \times 9.80}{0.600} = 1960\text{ N}

  3. Step 3

    fk=μkmgcos⁡(30.0∘)  ⟹  a=μkgcos⁡(30.0∘)=0.250×9.80×cos⁡(30.0∘)=2.12 m/s2f_k = \mu_k mg\cos(30.0^\circ) \implies a = \mu_k g\cos(30.0^\circ) = 0.250 \times 9.80 \times \cos(30.0^\circ) = 2.12\text{ m/s}^2

    Correct

    fk=μkmg  ⟹  a=μkg=0.250×9.80 m/s2=2.45 m/s2f_k = \mu_k mg \implies a = \mu_k g = 0.250 \times 9.80\text{ m/s}^2 = 2.45\text{ m/s}^2

    The crate has transitioned to a flat horizontal surface. On a level floor with no vertical incline, the normal force is FN=mgF_N = mg, not mgcos⁡(30.0∘)mg\cos(30.0^\circ).

  4. Step 4

    Δtfriction=v0a=9.802.12=4.62 s\Delta t_{\text{friction}} = \frac{v_0}{a} = \frac{9.80}{2.12} = 4.62\text{ s}

    Correct

    Δtfriction=v0a=9.80 m/s2.45 m/s2=4.00 s\Delta t_{\text{friction}} = \frac{v_0}{a} = \frac{9.80\text{ m/s}}{2.45\text{ m/s}^2} = 4.00\text{ s}

    Your stopping time formula Δt=v0a\Delta t = \frac{v_0}{a} is conceptually correct, but evaluating it with your underestimated acceleration a=2.12 m/s2a = 2.12\text{ m/s}^2 propagated the error into the final value.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly set up and solved conservation of mechanical energy for the descent down the frictionless ramp.

You correctly applied the impulse-momentum theorem to determine the average stopping force of the safety buffer.

You correctly related stopping time to initial velocity and deceleration via Δt=v0a\Delta t = \frac{v_0}{a}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incline angle carried over to level floor

You included cos⁡(30.0∘)\cos(30.0^\circ) in the normal force even though the crate had already transitioned off the incline onto a horizontal surface.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the normal force as mgcos⁡θmg\cos\theta across the entire problem instead of re-evaluating the free-body diagram when the crate transitioned from the 30.0∘30.0^\circ ramp to the flat horizontal floor. On a horizontal floor with no additional vertical forces, ΣFy=0\Sigma F_y = 0 yields FN=mgF_N = mg.

REASONING PATH
Your ACEpath teacher’s suggested approach
Re-evaluate Free-Body Diagrams Across Surface Transitions
  • The expression FN=mgcos⁡θF_N = mg\cos\theta applies only along a ramp of angle θ\theta. Once an object moves on a level horizontal plane, θ=0∘\theta = 0^\circ, so FN=mgF_N = mg.

  • Always pause when a problem states that an object leaves an incline or transitions to a level floor, and write a fresh vertical equilibrium equation for the new surface.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Establish vertical equilibrium on the flat floor: ΣFy=FN−mg=0  ⟹  FN=mg\Sigma F_y = F_N - mg = 0 \implies F_N = mg.

  2. Compute the kinetic friction force and deceleration: fk=μkmg  ⟹  a=μkg=0.250×9.80 m/s2=2.45 m/s2f_k = \mu_k mg \implies a = \mu_k g = 0.250 \times 9.80\text{ m/s}^2 = 2.45\text{ m/s}^2.

  3. Apply kinematics or impulse to find the stopping time: Δtfriction=v0a=9.80 m/s2.45 m/s2=4.00 s\Delta t_{\text{friction}} = \frac{v_0}{a} = \frac{9.80\text{ m/s}}{2.45\text{ m/s}^2} = 4.00\text{ s}.

Final answer

(a) v0=9.80 m/sv_0 = 9.80\text{ m/s}, (b) Fˉbuffer=1.96×103 N\bar{F}_{\text{buffer}} = 1.96 \times 10^3\text{ N}, (c) Δtfriction=4.00 s\Delta t_{\text{friction}} = 4.00\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review free-body diagrams for transitions between inclined planes and horizontal surfaces to ensure trigonometric factors are removed once the surface is level.

  • Practice setting up ΣFy=0\Sigma F_y = 0 explicitly whenever surface geometry changes rather than memorizing a single normal force template.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to take the square root when solving for velocity from kinetic energy, using v₀ = 2gh.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    mgh=12mv02  ⟹  v0=2gh=2×9.80×4.90=96.04 m/smgh = \frac{1}{2}mv_0^2 \implies v_0 = 2gh = 2 \times 9.80 \times 4.90 = 96.04\text{ m/s}

    Correct

    mgh=12mv02  ⟹  v0=2gh=2×9.80×4.90=9.80 m/smgh = \frac{1}{2}mv_0^2 \implies v_0 = \sqrt{2gh} = \sqrt{2 \times 9.80 \times 4.90} = 9.80\text{ m/s}

    You correctly equated gravitational potential energy to kinetic energy and canceled mass mm. However, after multiplying by 22, you isolated v0v_0 instead of v02v_0^2, forgetting to take the square root.

  2. Step 2

    Favg=mv0Δt  ⟹  Favg=120×96.040.600=19208 NF_{\text{avg}} = \frac{m v_0}{\Delta t} \implies F_{\text{avg}} = \frac{120 \times 96.04}{0.600} = 19208\text{ N}

    Correct

    Fˉbuffer=mv0Δt=120×9.800.600=1960 N=1.96×103 N\bar{F}_{\text{buffer}} = \frac{m v_0}{\Delta t} = \frac{120 \times 9.80}{0.600} = 1960\text{ N} = 1.96 \times 10^3\text{ N}

    Your application of the impulse-momentum theorem is completely correct, but the numerical result is affected by substituting the unrooted velocity from part (a).

  3. Step 3

    a=μkg=0.250×9.80=2.45 m/s2  ⟹  Δtfriction=v0a=96.042.45=39.2 sa = \mu_k g = 0.250 \times 9.80 = 2.45\text{ m/s}^2 \implies \Delta t_{\text{friction}} = \frac{v_0}{a} = \frac{96.04}{2.45} = 39.2\text{ s}

    Correct

    a=μkg=0.250×9.80=2.45 m/s2  ⟹  Δtfriction=v0a=9.802.45=4.00 sa = \mu_k g = 0.250 \times 9.80 = 2.45\text{ m/s}^2 \implies \Delta t_{\text{friction}} = \frac{v_0}{a} = \frac{9.80}{2.45} = 4.00\text{ s}

    Your determination of friction acceleration and stopping time is mathematically and physically sound, but the final value carries forward the incorrect initial speed from part (a).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that mechanical energy is conserved along the frictionless ramp.

You correctly applied the impulse-momentum theorem to relate stopping force, contact time, and momentum change.

You correctly determined the deceleration due to kinetic friction on a horizontal surface using a=μkga = \mu_k g.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Algebraic Isolation / Missing Square Root

You solved 12mv2=mgh\frac{1}{2}mv^2 = mgh by writing v=2ghv = 2gh rather than v2=2ghv^2 = 2gh.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Skipping the intermediate power step (v2=2ghv^2 = 2gh) when isolating a squared variable leads to equating speed directly to 2gh2gh, which dimensionally represents specific energy or squared velocity (m2/s2\text{m}^2/\text{s}^2) rather than velocity (m/s\text{m/s}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolating Squared Variables
  • If an expression contains v2v^2, clearing coefficients leaves v2v^2; you must apply a radical to obtain vv.

  • Always write down the explicit step v2=…v^2 = \dots before taking the square root: v=…v = \sqrt{\dots}.

Dimensional & Order-of-Magnitude Sanity Check
  • Speed must have units of m/s\text{m/s}, and an object falling ∼5 m\sim 5\text{ m} reaches roughly 10 m/s10\text{ m/s}, not nearly 100 m/s100\text{ m/s}.

  • Check units (2gh→[m/s2][m]=m2/s22gh \rightarrow [\text{m/s}^2][\text{m}] = \text{m}^2/\text{s}^2) and test whether the resulting speed matches everyday intuition before using it downstream.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Take the square root of both sides: v0=2gh=2(9.80 m/s2)(4.90 m)=96.04 m2/s2=9.80 m/sv_0 = \sqrt{2gh} = \sqrt{2(9.80\text{ m/s}^2)(4.90\text{ m})} = \sqrt{96.04\text{ m}^2/\text{s}^2} = 9.80\text{ m/s}.

  2. Substitute v0=9.80 m/sv_0 = 9.80\text{ m/s} into the buffer force formula: Fˉbuffer=mv0Δt=(120 kg)(9.80 m/s)0.600 s=1960 N=1.96×103 N\bar{F}_{\text{buffer}} = \frac{m v_0}{\Delta t} = \frac{(120\text{ kg})(9.80\text{ m/s})}{0.600\text{ s}} = 1960\text{ N} = 1.96 \times 10^3\text{ N}.

  3. Substitute v0=9.80 m/sv_0 = 9.80\text{ m/s} into the friction time equation: Δtfriction=v0μkg=9.80 m/s2.45 m/s2=4.00 s\Delta t_{\text{friction}} = \frac{v_0}{\mu_k g} = \frac{9.80\text{ m/s}}{2.45\text{ m/s}^2} = 4.00\text{ s}.

Final answer

(a) v0=9.80 m/sv_0 = 9.80\text{ m/s}, (b) Fˉbuffer=1.96×103 N\bar{F}_{\text{buffer}} = 1.96 \times 10^3\text{ N}, (c) Δtfriction=4.00 s\Delta t_{\text{friction}} = 4.00\text{ s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out v2=…v^2 = \dots as its own line whenever solving kinetic energy equations so you remember the square root step.

  • Perform a quick dimensional check whenever you compute velocity from acceleration and distance: [a][d]=m/s\sqrt{[a][d]} = \text{m/s}.

  • Re-evaluate downstream steps immediately whenever a computed speed appears unrealistically high for a modest drop height.

Lock it in

Similar question

01

A 2.0 kg2.0\text{ kg} sled starts from rest at the top of a frictionless hill of height h=7.2 mh = 7.2\text{ m} inclined at 25∘25^\circ. What is the sled's speed at the bottom of the hill? Take g=9.8 m/s2g = 9.8\text{ m/s}^2.

Answer

v=11.9 m/sv = 11.9\text{ m/s} (or 12 m/s12\text{ m/s}). Key steps: By conservation of energy, mgh=12mv2  ⟹  v=2gh=2(9.8)(7.2)=141.12≈11.9 m/smgh = \frac{1}{2}mv^2 \implies v = \sqrt{2gh} = \sqrt{2(9.8)(7.2)} = \sqrt{141.12} \approx 11.9\text{ m/s}. The angle 25∘25^\circ is extra information.

02

A 50 kg50\text{ kg} skier slides from rest down a frictionless 20∘20^\circ slope of length L=30 mL = 30\text{ m}. Upon reaching the bottom, they hit a snowbank that stops them in 0.80 s0.80\text{ s}. Find the magnitude of the average stopping force exerted by the snowbank. Take g=9.8 m/s2g = 9.8\text{ m/s}^2.

Answer

Fˉ=8.9×102 N\bar{F} = 8.9 \times 10^2\text{ N}. Key steps: (1) Find vertical drop: h=Lsin⁡θ=30sin⁡(20∘)≈10.26 mh = L\sin\theta = 30\sin(20^\circ) \approx 10.26\text{ m}. (2) Speed at bottom: v=2gh=2(9.8)(10.26)≈14.18 m/sv = \sqrt{2gh} = \sqrt{2(9.8)(10.26)} \approx 14.18\text{ m/s}. (3) Impulse-momentum: Fˉ=mvΔt=50×14.180.80≈886 N≈8.9×102 N\bar{F} = \frac{mv}{\Delta t} = \frac{50 \times 14.18}{0.80} \approx 886\text{ N} \approx 8.9 \times 10^2\text{ N}.

03

A 4.0 kg4.0\text{ kg} block is released from rest at the top of a ramp of vertical height h=3.2 mh = 3.2\text{ m} inclined at 37∘37^\circ. The ramp is frictionless, but the level floor at the base has a kinetic friction coefficient μk=0.40\mu_k = 0.40. (a) Find the speed at the base. (b) Find the stopping distance on the rough floor. (c) If the ramp angle were increased to 53∘53^\circ while keeping h=3.2 mh = 3.2\text{ m} constant, how would the stopping distance change? Take g=9.8 m/s2g = 9.8\text{ m/s}^2.

Answer

(a) v0=7.9 m/sv_0 = 7.9\text{ m/s}, (b) d=8.0 md = 8.0\text{ m}, (c) Unchanged. Key steps: (a) v0=2gh=2(9.8)(3.2)≈7.92 m/sv_0 = \sqrt{2gh} = \sqrt{2(9.8)(3.2)} \approx 7.92\text{ m/s}. (b) Work-energy on floor: fkd=12mv02  ⟹  μkmgd=mgh  ⟹  d=hμk=3.20.40=8.0 mf_k d = \frac{1}{2}mv_0^2 \implies \mu_k mg d = mgh \implies d = \frac{h}{\mu_k} = \frac{3.2}{0.40} = 8.0\text{ m}. (c) Since d=hμkd = \frac{h}{\mu_k} depends only on vertical height hh and μk\mu_k, changing the incline angle has no effect on the final stopping distance.

Loading workspace…