Resources

An experimenter applies an adjustable potential difference VV across a fixed ohmic cylindrical resistor of resistance R=82.0 ΩR = 82.0\ \Omega. Measurements indicate that a total electric charge of Q=55.35 CQ = 55.35\text{ C} traverses the full cross-section of the resistor over an elapsed time interval of Δt=45.0 s\Delta t = 45.0\text{ s}. Assuming the resistor strictly obeys Ohm's law, determine: (a) the constant electric current II passing through the resistor, and (b) the required terminal voltage VV applied across the resistor.

Answer and steps

Final answer

(a) I=1.23 AI = 1.23\text{ A}; (b) V=101 VV = 101\text{ V} (or 1.01×102 V1.01 \times 10^2\text{ V})

Steps

Part (a): Determining the Electric Current II

  1. Definition of Electric Current: Electric current II is the rate at which electric charge QQ flows through a cross-sectional area of a conductor over a time interval Δt\Delta t: I=QΔtI = \frac{Q}{\Delta t}
  2. Calculation: Substitute the given values of charge (Q=55.35 CQ = 55.35\text{ C}) and time (Δt=45.0 s\Delta t = 45.0\text{ s}): I=55.35 C45.0 s=1.23 AI = \frac{55.35\text{ C}}{45.0\text{ s}} = 1.23\text{ A}

Part (b): Determining the Applied Potential Difference VV

  1. Applying Ohm's Law: For an ohmic conductor of constant resistance RR, the potential difference (voltage) VV across its terminals is directly proportional to the current II flowing through it: V=I⋅RV = I \cdot R
  2. Calculation: Using the calculated current I=1.23 AI = 1.23\text{ A} and the given resistance R=82.0 ΩR = 82.0\ \Omega: V=1.23 A⋅82.0 Ω=100.86 VV = 1.23\text{ A} \cdot 82.0\ \Omega = 100.86\text{ V}
  3. Significant Figures: Rounding to three significant figures to match the precision of the given data (45.0 s45.0\text{ s} and 82.0 Ω82.0\ \Omega): V≈101 V(or 1.01×102 V)V \approx 101\text{ V} \quad (\text{or } 1.01 \times 10^2\text{ V})

Common Pitfalls to Avoid

  • Confusing Current and Charge: Charge (QQ, measured in coulombs, C\text{C}) represents the quantity of electricity, whereas current (II, measured in amperes, A=C/s\text{A} = \text{C/s}) represents its rate of flow. Always divide the total charge by the elapsed time to find the current.
  • Premature Rounding: Keep unrounded values in intermediate steps when performing sequential calculations to prevent rounding errors in the final voltage value.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student multiplies charge by time instead of dividing to find the current, resulting in an incorrect current and subsequent voltage.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    I=Q∗Δt  ⟹  I=55.335∗45.0=2490.75 AI = Q * \Delta t \implies I = 55.335 * 45.0 = 2490.75\text{ A}

    Correct

    I=QΔt=55.35 C45.0 s=1.23 AI = \frac{Q}{\Delta t} = \frac{55.35\text{ C}}{45.0\text{ s}} = 1.23\text{ A}

    Electric current is the rate of charge flow per unit time, defined as I=QΔtI = \frac{Q}{\Delta t}, not the product Q⋅ΔtQ \cdot \Delta t. In addition, the problem provided Q=55.35 CQ = 55.35\text{ C} rather than 55.335 C55.335\text{ C}.

  2. Step 2

    V=I∗R  ⟹  V=2490.75∗82.0=204241.5 VV = I * R \implies V = 2490.75 * 82.0 = 204241.5\text{ V}

    Correct

    V=I⋅R=(1.23 A)(82.0 Ω)≈101 VV = I \cdot R = (1.23\text{ A})(82.0\ \Omega) \approx 101\text{ V}

    Your application of Ohm's law V=IRV = I R is algebraically correct, but the calculated voltage is inaccurate because it uses the incorrect current from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that Ohm's law connects voltage, current, and resistance via the relationship V=IRV = I R.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula inversion / rate definition confusion

You copied the given charge value as 55.335 C55.335\text{ C} instead of 55.35 C55.35\text{ C}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated current as the product of charge and time (Q⋅ΔtQ \cdot \Delta t) rather than the rate of charge flow (Q/ΔtQ / \Delta t). Checking units would immediately reveal that C⋅s≠A\text{C}\cdot\text{s} \neq \text{A}, since 1 A=1 C/s1\text{ A} = 1\text{ C/s}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Definition of Current
  • I=ΔQΔtI = \frac{\Delta Q}{\Delta t} with units of amperes (1 A=1 C/s1\text{ A} = 1\text{ C/s}).

  • Always set up current as charge divided by time interval.

Unit Dimensional Check
  • Multiplying coulombs by seconds yields C⋅s\text{C}\cdot\text{s}, not amperes.

  • Verify that your intermediate calculated unit matches the target physical unit before substituting into subsequent equations.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the electric current using the rate definition: I=QΔt=55.35 C45.0 s=1.23 AI = \frac{Q}{\Delta t} = \frac{55.35\text{ C}}{45.0\text{ s}} = 1.23\text{ A}.

  2. Substitute the corrected current into Ohm's law: V=I⋅R=(1.23 A)(82.0 Ω)=100.86 VV = I \cdot R = (1.23\text{ A})(82.0\ \Omega) = 100.86\text{ V}.

  3. Round to three significant figures to match the given measurements.

Final answer

(a) I=1.23 AI = 1.23\text{ A}; (b) V=101 VV = 101\text{ V} (or 1.01×102 V1.01 \times 10^2\text{ V})

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the fundamental definition of electric current as charge flow rate (I=Q/ΔtI = Q / \Delta t).

  • Practice using dimensional analysis to catch inverted formulas before computing values.

  • Solve the practice problems below to consolidate using I=Q/ΔtI = Q / \Delta t alongside Ohm's law V=IRV = I R.

OverviewACEpath Teacher's Diagnosis

02 The student misremembers Ohm's law as V = I / R instead of V = I * R, leading to an incorrect terminal voltage.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    I=QΔt  ⟹  I=55.3545.0=1.23 AI = \frac{Q}{\Delta t} \implies I = \frac{55.35}{45.0} = 1.23\text{ A}

  2. Step 2

    V=IR  ⟹  V=1.2382.0=0.015 VV = \frac{I}{R} \implies V = \frac{1.23}{82.0} = 0.015\text{ V}

    Correct

    V=I⋅R=(1.23 A)(82.0 Ω)=100.86 V≈101 VV = I \cdot R = (1.23\text{ A})(82.0\ \Omega) = 100.86\text{ V} \approx 101\text{ V}

    You wrote Ohm's law as V=IRV = \frac{I}{R} instead of V=I⋅RV = I \cdot R. Potential difference is proportional to both current and resistance, so you need to multiply them.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recalled the definition formula for electric current I=QΔtI = \frac{Q}{\Delta t}.

You substituted the given values of charge and elapsed time accurately to find I=1.23 AI = 1.23\text{ A}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Ohm's Law Algebraic Form Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the rearranged forms of Ohm's law (I=VRI = \frac{V}{R}, V=IRV = IR, R=VIR = \frac{V}{I}), incorrectly setting voltage equal to current divided by resistance instead of their product.

REASONING PATH
Your ACEpath teacher’s suggested approach
Ohm's Law Triangle / Base Relationship
  • V=I⋅RV = I \cdot R, which rearranges to I=VRI = \frac{V}{R} and R=VIR = \frac{V}{I}.

  • Check units before computing: [A]⋅[Ω]=[V][\text{A}] \cdot [\Omega] = [\text{V}], whereas dividing amperes by ohms gives A/Ω=V/Ω2\text{A}/\Omega = \text{V}/\Omega^2, not volts.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply Ohm's law for terminal voltage: V=I⋅RV = I \cdot R.

  2. Substitute I=1.23 AI = 1.23\text{ A} and R=82.0 ΩR = 82.0\ \Omega: V=(1.23 A)(82.0 Ω)=100.86 VV = (1.23\text{ A})(82.0\ \Omega) = 100.86\text{ V}.

  3. Round to three significant figures to match the given data: V≈101 VV \approx 101\text{ V}.

Final answer

(a) I=1.23 AI = 1.23\text{ A}; (b) V=101 VV = 101\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the three algebraic arrangements of Ohm's law using the VV on top relationship (V=IRV = IR).

  • Perform a quick dimensional check whenever computing voltage to verify that you are multiplying current by resistance.

OverviewACEpath Teacher's Diagnosis

03 The student misidentifies terminal voltage as being given by V = R / I, resulting in an erroneous potential difference.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    I=QΔt  ⟹  I=55.3545.0=1.23 AI = \frac{Q}{\Delta t} \implies I = \frac{55.35}{45.0} = 1.23\text{ A}

  2. Step 2

    V=RI  ⟹  V=82.01.23=66.67 VV = \frac{R}{I} \implies V = \frac{82.0}{1.23} = 66.67\text{ V}

    Correct

    V=IR=(1.23 A)(82.0 Ω)≈101 VV = I R = (1.23\text{ A})(82.0\ \Omega) \approx 101\text{ V}

    According to Ohm's law, potential difference is proportional to both current and resistance (V=IRV = I R), not resistance divided by current.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the definition of electric current as the rate of charge flow over time.

You calculated the value of the current accurately with proper units in part (a).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Ohm's Law Algebraic Rearrangement Error

You set up the formula for voltage as a quotient RI\frac{R}{I} instead of the product IRI R.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You likely confused the rearrangement R=VIR = \frac{V}{I} with the direct formula for potential difference V=IRV = I R.

REASONING PATH
Your ACEpath teacher’s suggested approach
Ohm's Law Triangle / Form
  • Potential difference equals current multiplied by resistance (V=IRV = I R).

  • Whenever solving for voltage VV, multiply current II and resistance RR; division by current gives resistance (R=VIR = \frac{V}{I}).

Dimensional Unit Check
  • Volts=Amperes×Ohms\text{Volts} = \text{Amperes} \times \text{Ohms} (1 V=1 A⋅Ω1\text{ V} = 1\text{ A}\cdot\Omega).

  • Check units: ΩA\frac{\Omega}{\text{A}} does not equal volts, whereas A⋅Ω\text{A} \cdot \Omega yields volts.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recall Ohm's law relating voltage, current, and resistance: V=IRV = I R.

  2. Substitute I=1.23 AI = 1.23\text{ A} and R=82.0 ΩR = 82.0\ \Omega: V=(1.23 A)(82.0 Ω)=100.86 VV = (1.23\text{ A})(82.0\ \Omega) = 100.86\text{ V}.

  3. Round to three significant figures to match the input data.

Final answer

V=101 VV = 101\text{ V} (or 1.01×102 V1.01 \times 10^2\text{ V})

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice rearranging Ohm's law into its three equivalent forms: V=IRV = I R, I=VRI = \frac{V}{R}, and R=VIR = \frac{V}{I}.

  • Use a quick unit sanity check before finalizing algebraic calculations.

Lock it in

Similar question

01

A steady current flows through a heating element with resistance R=24.0 ΩR = 24.0\ \Omega. If 72.0 C72.0\text{ C} of charge passes through the element in 30.0 s30.0\text{ s}, calculate (a) the electric current II and (b) the voltage VV across the element.

Answer

(a) I=QΔt=72.0 C30.0 s=2.40 AI = \frac{Q}{\Delta t} = \frac{72.0\text{ C}}{30.0\text{ s}} = 2.40\text{ A}. (b) Using Ohm's law, V=IR=(2.40 A)(24.0 Ω)=57.6 VV = I R = (2.40\text{ A})(24.0\ \Omega) = 57.6\text{ V}.

02

A potential difference of 12.0 V12.0\text{ V} is applied across a resistor, producing a current of 0.750 A0.750\text{ A}. (a) Find the resistance RR. (b) How much total charge QQ traverses the resistor in 2.00 minutes2.00\text{ minutes}?

Answer

(a) R=VI=12.0 V0.750 A=16.0 ΩR = \frac{V}{I} = \frac{12.0\text{ V}}{0.750\text{ A}} = 16.0\ \Omega. (b) Convert time: Δt=2.00 min=120 s\Delta t = 2.00\text{ min} = 120\text{ s}. Then Q=IΔt=(0.750 A)(120 s)=90.0 CQ = I \Delta t = (0.750\text{ A})(120\text{ s}) = 90.0\text{ C}.

03

An electronic component with resistance R=150 ΩR = 150\ \Omega operates under an unknown constant terminal voltage. Over an interval of 1.50 minutes1.50\text{ minutes}, 5.40×10205.40\times 10^{20} conduction electrons traverse the component. Taking the elementary charge as e=1.60×10−19 Ce = 1.60\times 10^{-19}\text{ C}, determine (a) the electric current II and (b) the terminal voltage VV.

Answer

Total charge: Q=Ne=(5.40×1020)(1.60×10−19 C)=86.4 CQ = N e = (5.40\times 10^{20})(1.60\times 10^{-19}\text{ C}) = 86.4\text{ C}. Time in seconds: Δt=1.50 min=90.0 s\Delta t = 1.50\text{ min} = 90.0\text{ s}. (a) I=QΔt=86.4 C90.0 s=0.960 AI = \frac{Q}{\Delta t} = \frac{86.4\text{ C}}{90.0\text{ s}} = 0.960\text{ A}. (b) V=IR=(0.960 A)(150 Ω)=144 VV = I R = (0.960\text{ A})(150\ \Omega) = 144\text{ V}.

Loading workspace…